Synthesis and crystallization behavior of rigid copolyesters with biphenyl‐4,4′‐dicarboxylate and 2,6‐naphthalenedicarboxylate in the main chain

Structurally rigid copolyester thermoplastics were synthesized from 1,4‐cyclohexanedimethanol and the diesters dimethyl biphenyl‐4,4′‐dicarboxylate and dimethyl 2,6‐naphthalenedicarboxylate (DMN) via conventional melt transesterification. Conventional differential scanning calorimetry (CDSC) showed all compositions to exhibit multiple endotherms upon heating. Wide‐angle X‐ray diffraction analysis showed copolyester compositions to exhibit the crystalline structure of either the homopolyester Poly(1,4‐cyclohexylenedimethylene 2,6‐naphthalate) (PCN) or the homopolyester Poly(1,4‐cyclohexylenedimethylene 4,4′‐bibenzoate) (PCB), but not both simultaneously. Further thermal analysis using CDSC and fast DSC investigated the origin of the multiple endotherm behavior. While three endotherms are observed for low heating rates, the upper two endotherms appear to merge at heating rates about 1–5 °C s^?1 and a single endotherm remains above heating rates about 10–50 °C s^?1. While the behavior of the upper two endotherms is undeniably consistent with the mechanism of melting–recrystallization–remelting (MRR), we suggest that the low endotherm is likely associated with the melting of constrained secondary crystals, although MRR effects cannot be ruled out. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 973–980     

Synthesis and properties of cyclic diester based aliphatic copolyesters

Melt polycondensation was used to prepare a systematic series of random and amorphous copolyesters using the following cycloaliphatic diesters: dimethyl‐1,4‐cyclohexane dicarboxylate (DMCD), dimethyl bicyclo[2.2.1]heptane‐1,4‐dicarboxylate (DMCD‐1), dimethyl bicyclo[2.2.2]octane‐1,4‐dicarboxylate (DMCD‐2), dimethyl bicyclo[3.2.2]nonane‐1,5‐dicarboxylate (DMCD‐3), 1,4‐dimethoxycarbonyl‐1,4‐dimethylcyclohexane (DMCD‐M) and the aliphatic diols: ethylene glycol (EG) and 1,4‐cyclohexane dimethanol (CHDM). The polymer compositions were determined by nuclear magnetic resonance (NMR) and the molecular weights were determined using size exclusion chromatography (SEC). The polyesters were characterized by dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The copolyester based on DMCD‐2 was observed to have a higher glass transition temperature (T_g up to 115 °C) than the other copolyesters of this study. For poly[x(DMCD‐2)y(DMCD) 30(EG)70(CHDM)], T_g increases linearly with increase of DMCD‐2 mole content. DMA showed that all of the cycloaliphatic copolyesters have secondary relaxations, resulting from the conformational transitions of the cyclohexylene rings. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2162–2169, 2010     

Block copolyesters of poly(pentamethylene p,p′‐bibenzoate) and poly(tetramethylene adipate)

Hydroxy‐terminated poly(pentamethylene p,p′‐bibenzoate) oligomers with different molecular weights were prepared. The poly(pentamethylene p,p′‐bibenzoate) oligomers showed rather high crystallinity, and some of them exhibited a monotropic smectic phase. Block copolyesters with hard segments of poly(pentamethylene p,p′‐bibenzoate) and soft segments of poly(tetramethylene adipate) were prepared by coupling the poly(pentamethylene p,p′‐bibenzoate) oligomer and a poly(tetramethylene adipate)glycol with methylene‐4,4′‐diphenylene diisocyanate in solution. The block copolyesters were characterized by IR, ¹H NMR, differential scanning calorimetry, a polarized microscope, and X‐ray diffraction. The thermal transitions of the block copolyesters were dependent on the composition and the molecular weight of the poly(pentamethylene p,p′‐bibenzoate) oligomer used. The hard segments in the block copolyesters showed no liquid crystallinity and exhibited rather low crystallinity or were even amorphous. The molecular weight of the poly(pentamethylene p,p′‐bibenzoate) oligomer used influences the glass‐transition temperature and crystalline properties of the soft segments in the block copolyesters significantly. The effect on the glass‐transition temperature of the soft segments is described as the difference in miscibility between the hard and soft segments. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2626–2636, 2002     

Aromatic polybenzoxazoles containing ether–sulfone linkages

A series of poly(o‐hydroxy amide)s having both ether and sulfone linkages in the main chain were synthesized via the low‐temperature solution polycondensation of 4,4′‐[sulfonylbis(1,4‐phenylene)dioxy]dibenzoyl chloride and 4,4′‐[sulfonylbis(2,6‐dimethyl‐1,4‐phenylene)dioxy]dibenzoyl chloride with three bis(o‐aminophenol)s including 4,4′‐diamino‐3,3′‐dihydroxybiphenyl, 3,3′‐diamino‐4,4′‐dihydroxybiphenyl, and 2,2‐bis(3‐diamino‐4‐hydroxyphenyl)hexafluoropropane. Subsequent thermal cyclodehydration of the poly(o‐hydroxy amide)s afforded polyethersulfone benzoxazoles. Most of the poly(o‐hydroxy amide)s were soluble in polar organic solvents such as N‐methyl‐2‐pyrrolidone; however, the polybenzoxazoles without the hexafluoroisopropylidene group were organic‐insoluble. The polybenzoxazoles exhibited glass‐transition temperatures (T_g) in the range of 219–282 °C by DSC and softening temperatures (T_s) of 242–320 °C by thermomechanical analysis. Thermogravimetric analyses indicated that most polybenzoxazoles were stable up to 450 °C in air or nitrogen. The 10% weight loss temperatures were recorded in the ranges of 474–593 °C in air and 478–643 °C in nitrogen. The methyl‐substituted polybenzoxazoles had higher T_g's but lower T_s's and initial decomposition temperatures compared with the corresponding unsubstituted polybenzoxazoles. For a comparative purpose, the synthesis and characterization of a series of sulfonyl polybenzoxazoles without the ether group that derived from 4,4′‐sulfonyldibenzoyl chloride and bis(o‐aminophenol)s were also reported. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2262–2270, 2001     

Oxygen‐barrier properties of copolymers based on ethylene terephthalate

The oxygen‐barrier properties of amorphous polyethylene terephthalate‐based copolymers with various acid comonomers were examined. The incorporation of increasing amounts of isophthalate, phthalate, or naphthalate gradually reduced the permeability P toward the low values obtained for the corresponding homopolymers. The permeability of poly(ethylene 3,4′‐bibenzoate) homopolymer was only slightly lower than that of polyethylene terephthalate, and the copolymers correspondingly exhibited a very gradual decrease in P as the amount of 3,4′‐bibenzoate (3,4′BB) increased. In contrast, copolymerization with the linear isomer, 4,4′BB, produced a substantial increase in P. Generally, comonomer affected the solubility S less than the diffusivity D, and therefore changes in P reflected primarily changes in D for the polymers studied. The diffusivity and solubility depended on the copolymer composition in accordance with static and dynamic free‐volume concepts of gas permeability in glassy polymers. The solubility S correlated with the amount of free volume as determined by the glass‐transition temperature. Correlation of the diffusivity D with the magnitude of the subambient γ relaxation identified dynamic free volume with thermally activated conformational changes and segmental motions. Correspondence in the activation energy confirmed the relationship. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1889–1899, 2001     

Linear polyurethanes made from naturally occurring tartaric acid

Naturally occurring tartaric acid was used as raw material for the synthesis of novel linear polyurethanes (PURs) bearing two carboxylate side‐groups in the repeating unit. Aliphatic and aromatic PURs were obtained by reaction in solution of alkyl and benzyl tartrates with hexamethylene diisocyanate and 4,4′‐methylene‐bis(phenyl isocyanate), respectively. All the novel PURs were thermally stable and optically active. The aliphatic carboxylate‐containing PURs had M_w in the 40–70 kDa range, with PD between 2.1 and 2.5; all were semicrystalline polymers with melting temperatures between 100 and 150 °C and T_g in the 50–80 °C range. The aromatic PURs were amorphous materials with molecular weights between 18 kDa and 25 kDa and T_g above 130 °C. Hydrogenolysis of the PUR made from hexamethylene diisocyanate and benzyl tartrate yielded PURs containing up to 40% of free carboxylic side‐groups. The tartrate‐derived PURs displayed enhanced sensitivity to hydrolysis compared with their unsubstituted 2,6‐PUR homologs. The PURs bearing free carboxylic groups were unique in being degraded by water upon incubation under physiological conditions. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2391–2407, 2009     

Synthesis and characterization of hyperbranched polyimides with good organosolubility and thermal properties based on a new triamine and conventional dianhydrides

A triamine monomer, 1,3,5‐tris(4‐aminophenoxy)benzene (TAPOB), was synthesized from phloroglucinol and 4‐chloronitrobenzene, and it was successfully polymerized into soluble hyperbranched polyimides (HB PIs) with commercially available dianhydrides: 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride (6FDA), 4,4′‐oxydiphthalic anhydride (ODPA), and 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride (BTDA). Different monomer addition methods and different monomer molar ratios resulted in HB PIs with amino or anhydride end groups. From ¹H NMR spectra, the degrees of branching of the amino‐terminated polymers were estimated to be 0.65, 0.62, and 0.67 for 6FDA–TAPOB, ODPA–TAPOB, and BTDA–TAPOB, respectively. All polymers showed good thermal properties with 10% weight‐loss temperatures (T₁₀'s) above 505 °C and glass‐transition temperatures (T_g's) of 208–282 °C for various dianhydrides. The anhydride‐terminated HB PIs showed lower T₁₀ and T_g values than their amino‐terminated counterparts. The chemical conversion of the terminal amino or anhydride groups of the 6FDA‐based polyimides into an aromatic imido structure improved their thermal stability, decreased their T_g, and improved their solubility. The HB PIs had moderate molecular weights with broad distributions. The 6FDA‐based HB PIs exhibited good solubility even in common low‐boiling‐point solvents such as chloroform, tetrahydrofuran, and acetone. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3804–3814, 2002     

Synthesis and characterization of phthalazinone containing poly(arylene ether)s via a novel N–C coupling reaction

High‐molecular‐weight poly(phthalazinone)s with very high glass‐transition temperatures (T_g's) were synthesized via a novel N–C coupling reaction. New bisphthalazinone monomers ( 7a–e ) were synthesized from 2‐(4‐chlorobenzoyl) phthalic acid in two steps. Poly(phthalazinone)s, having inherent viscosities in the range of 0.34–0.91 dL/g, were prepared by the reaction of the bis(phthalazinone) monomers with an activated aryl halide in a dipolar aprotic solvent in the presence of potassium carbonate. The poly(phthalazinone)s exhibited T_g's greater than 230 °C. polymer 8b synthesized from diphenyl biphenol and bis(4‐flurophenyl) sulfone demonstrated the highest T_g of 297 °C. Thermal stabilities of the poly(phthalazinone)s were determined by thermogravimetric analysis. All the poly(phthalazinone)s showed a similar pattern of decomposition with no weight loss below 450 °C in nitrogen. The temperatures of 5% weight loss were observed to be about 500 °C. The poly(phthalazinone)s containing 4,4′‐isopropylidenediphenol and 4,4′‐(hexafluoroisopropylidene) diphenol and diphenyl ether linkage were soluble in chlorinated solvents such as chloroform. Other poly‐(phthalazinone)s were soluble in dipolar aprotic solvents such as N,N′‐dimethylacetamide. The soluble poly(phthalazinone)s can be cast as flexible films from solution. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2481–2490, 2003     

Synthesis and properties of poly(ether imide)s based on the bis(ether anhydride)s from hydroquinone and its derivatives

Four bis(ether anhydride)s, 4,4′‐(1,4‐phenylenedioxy)diphthalic anhydride (IV), 4,4′‐(2,5‐tolylenedioxy)‐diphthalic anhydride (Me‐IV), 4,4′‐(2‐chloro‐1,4‐phenylenedioxy)diphthalic anhydride (Cl‐IV), and 4,4′‐(2,5‐biphenylenedioxy)diphthalic anhydride (Ph‐IV), were prepared in three steps starting from the nucleophilic nitrodisplacement reaction of 4‐nitrophthalonitrile with the potassium phenoxides of hydroquinone and various substituted hydroquinones such as methylhydroquinone, chlorohydroquinone, and phenylhydroquinone in N,N‐dimethylformamide, followed by alkaline hydrolysis and dehydration. Four series of poly(ether imide)s were prepared from bis(ether anhydride)s with various aromatic diamines by a classical two‐step procedure. The inherent viscosities of the intermediate poly(amic acid)s were in the range of 0.40–2.63 dL/g. Except for those derived from p‐phenylenediamine and benzidine, almost all the poly(amic acid)s could be solution‐cast and thermally converted into transparent, flexible, and tough polyimide films. Introduction of the chloro or phenyl substituent leads to a decreased crystallinity and an increased solubility of the polymers. The glass transition temperatures (T_g) of these polyimides were recorded in the range of 204–263°C. In general, the methyl‐ and chloro‐substituted polyimides exhibited relatively higher T_gs, whereas the phenyl‐substituted ones exhibited slightly lower T_gs compared to the corresponding nonsubstituted ones. Thermogravimetric analysis (TG) showed that 10% weight loss temperatures of all the polymers were above 500°C either in nitrogen or in air. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 665–675, 1999     

Synthesis and properties of novel Y‐type nonlinear optical polyimides with high thermal stability of second harmonic generation

2,4‐Bis‐(3,4‐dicarboxyphenylcarboxyethoxy)‐1‐(2,2‐dicyanovinyl)benzene dianhydride (4) was prepared and reacted with 4,4′‐oxydianiline, 4,4′‐diaminobenzanilide and 4,4′‐(hexafluoroisopropylidene)dianiline to yield novel Y‐type polyimides 5‐7 containing 2,4‐dioxybenzylidenemalononitrile groups as nonlinear optical (NLO) chromophores, which constitute parts of the polymer backbone. The resulting polyimides 5‐7 are soluble in polar solvents such as dimethylsulfoxide and N,N‐dimethylformamide. Polymers 5‐7 showed a thermal stability up to 330 °C in thermogravimetric analysis thermograms with T_g values obtained from differential scanning calorimetry thermograms in the range 179–194 °C. The second harmonic generation (SHG) coefficients (d₃₃) of poled polymer films at the 1064 nm fundamental wavelength were around 5.56 × 10^?9 esu. The dipole alignment exhibited exceptionally high thermal stability even at 20 °C higher than the glass‐transition temperature there was no SHG decay below 215 °C because of the partial main‐chain character of polymer structure, which is acceptable for NLO device applications. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3078–3087, 2008     

Improvement of thermoplasticity for s‐BPDA/PDA by copolymerization and blend with novel asymmetric BPDA‐based polyimides

Asymmetric biphenyl type polyimides (PI) derived from 2,3,3′,4′‐biphenyltetracarboxylic dianhydride (a‐BPDA) and p‐phenylenediamine (PDA) or 4,4′‐oxydianiline (ODA) show higher T_gs, and much better thermoplasticity than the corresponding isomeric PIs from symmetric 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (s‐BPDA). In addition, a‐BPDA‐derived PIs are completely amorphous owing to their bent chain structures and highly distorted conformations, whereas the PIs from s‐BPDA are semicrystalline. a‐BPDA‐derived PIs possessing these properties or the a‐BPDA monomer were used as a flexible blend component or a comonomer to improve the insufficient thermoplasticity of semirigid s‐BPDA/PDA homo polymer. The blends composed of s‐BPDA/PDA (80%) with a‐BPDA‐derived PIs (20%), as well as the s‐BPDA/PDA‐based copolymer containing 20% a‐BPDA, showed a certain extent of thermoplasticity above the T_gs without causing a decrease in T_g. In addition, these blends and copolymer provided comparatively low thermal expansion coefficient (ca. 18 ppm). The improved film properties for the blends are related to good blend miscibility. On the other hand, when s‐BPDA/ODA was used as a flexible matrix polymer instead of a‐BPDA‐derived PIs, the 80/20 blend film annealed at 400°C exhibited no prominent softening at the T_g. This result arises from annealing‐induced crystallization of the flexible s‐BPDA/ODA component. Thus, these results revealed that a‐BPDA‐derived PIs are promising candidates as matrix polymers for semirigid s‐BPDA/PDA for the present purpose. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2499–2511, 1999     

Synthesis and properties of 4,4′-biphenyldicarboxylic acid and 2,6-naphthalenedicarboxylic acid

This article describes the synthesis and the properties of polyesters and copolyesters prepared from ethylene glycol, terephthalic acid, 4,4′ biphenyldicarboxylic acid (BDA), and 2,6-naphthlenedicarboxylic acid (NDA). The effect of incorporating varying levels of BDA and NDA on polyethylene terephthalate (PET) is described. Depending on the concentration, incorporation of BDA into PET leads to an improvement in glass transition temperature (T_g), strength, modulus, and barrier properties. Copolymers of PET containing up to about 50% BDA derived units are clear and have T_g's ranging from 85 to 105°C, making them suitable for applications where a high T_g along with clarity is important. Copolymers with higher BDA concentration are highly crystalline, with high rates of crystallization from the melt. Copolymerization of NDA with oligoethyleneterephthalate leads to copolymers that are generally amorphous. Crystallinity can be developed in copolymers with low concentration of NDA by thermal annealing. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3139–3146, 1999     

Hydrazine‐based polyimides from isomeric bis(chlorophthalimide)s

3,3′‐Dichloro‐N,N′‐biphthalimide (3,3′‐DCBPI), 3,4′‐dichloro‐N,N′‐biphthalimide (3,4′‐DCBPI), and 4,4′‐dichloro‐N,N′‐biphthalimide (4,4′‐DCBPI) were synthesized from 3‐ or 4‐chlorophthalic anhydrides and hydrazine in glacial acetic acid. The yield of 3,3′‐DCBPI (90%) was much higher than that of 4,4′‐DCBPI (33%) because of the better stability of the intermediate, 3‐chloro‐N‐aminophthalimide, and 3,3′‐DCBPI. A series of hydrazine‐based polyimides were prepared from isomeric DCBPIs and 4,4′‐thiobisbenzenethiol (TBBT) in N,N‐dimethylacetamide in the presence of tributylamine. Inherent viscosity of these polymers was in the range of 0.51–0.69 dL/g in 1‐methyl‐2‐pyrrolidinone (NMP) at 30 °C. These polyimides were soluble in 1,1,2,2‐terachloroethane, NMP, and phenols. The 5% weight‐loss temperatures (T_5%s) of the polymers were near 450 °C in N₂. Their glass‐transition temperatures (T_gs) determined by dynamic mechanical thermal analysis and differential scanning calorimetry increased according to the order of polyimides based on 4,4′‐DCBPI, 3,4′‐DCBPI, and 3,3′‐DCBPI. The hydrolytic stability of these polymers was measured under acid, basic, and neutral conditions and the results indicated that the order was 3,3′‐DCBPI/TBBT > 3,4′‐DCBPI/TBBT > 4,4′‐DCBPI/TBBT. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4933–4940, 2007     

Synthesis and nonlinear optical properties of novel Y‐type polyurethane containing tricyanovinylthiazole with enhanced thermal stability of second harmonic generation

A novel Y‐type poly[iminocarbonyloxyethyl‐5‐methyl‐4‐{2‐thiazolylazo‐4‐(1,2,2‐tricyanovinyl)}resorcinoxyethyloxycarbonylimino‐(3,3′‐dimethoxy‐4,4′‐biphenylene)] 4 containing 5‐methyl‐4‐{5‐(1,2,2‐tricyanovinyl)‐2‐thiazolylazo}resorcinoxy groups as nonlinear optical (NLO) chromophores, which constitute part of the polymer backbone, was prepared and characterized. Polyurethane 4 is soluble in common organic solvents such as acetone and N,N‐dimethylformamide. It showed a thermal stability up to 250 °C in thermogravimetric analysis thermogram and the glass‐transition temperature (T_g) obtained from differential scanning calorimetry thermogram was around 118 °C. The second harmonic generation coefficient (d₃₃) of poled polymer films at 1560 nm fundamental wavelength was around 8.43 × 10^?9 esu. The dipole alignment exhibited a thermal stability even at 12 °C higher than T_g, and there was no SHG decay below 130 °C due to the partial main‐chain character of the polymer structure, which is acceptable for NLO device applications. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1166–1172, 2010     

Synthesis and properties of noncoplanar rigid‐rod aromatic polyhydrazides and poly(1,3,4‐oxadiazole)s containing phenyl or naphthyl substituents

Two new phenyl‐ and naphthyl‐substituted rigid‐rod aromatic dicarboxylic acid monomers, 2,2′‐diphenylbiphenyl‐4,4′‐dicarboxylic acid ( 4 ) and 2,2′‐di(1‐naphthyl)biphenyl‐4,4′‐dicarboxylic acid ( 5 ), were synthesized by the Suzuki coupling reaction of 2,2′‐diiodobiphenyl‐4,4′‐dicarboxylic acid dimethyl ester with benzeneboronic acid and naphthaleneboronic acid, respectively, followed by alkaline hydrolysis of the ester groups. Four new polyhydrazides were prepared from the dicarboxylic acids 4 and 5 with terephthalic dihydrazide (TPH) and isophthalic dihydrazide (IPH), respectively, via the Yamazaki phosphorylation reaction. These polyhydrazides were amorphous and readily soluble in many organic solvents. Differential scanning calorimetry (DSC) indicated that these hydrazide polymers had glass transition temperatures in the range of 187–234 °C and could be thermally cyclodehydrated into the corresponding oxadiazole polymers in the range of 300–400 °C. The resulting poly(1,3,4‐oxadiazole)s exhibited T_g's in the range of 252–283 °C, 10% weight‐loss temperature in excess of 470 °C, and char yield at 800 °C in nitrogen higher than 54%. These organo‐soluble polyhydrazides and poly(1,3,4‐oxadiazole)s exhibited UV–Vis absorption maximum at 262–296 and 264–342 nm in NMP solution, and their photoluminescence spectra showed maximum bands around 414–445 and 404–453 nm, respectively, with quantum yield up to 38%. The electron‐transporting properties were examined by electrochemical methods. Cyclic voltammograms of the poly(1,3,4‐oxadiazole) films cast onto an indium‐tin oxide (ITO)‐coated glass substrate exhibited reversible reduction redox with E_onset at ?1.37 to ?1.57 V versus Ag/AgCl in dry N,N‐dimethylformamide solution. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6466–6483, 2006     

Aromatic poly(benzoxazole)s from multiring diacids containing (phenylenedioxy)diphenylene or (naphthalenedioxy)diphenylene groups: Synthesis and thermal properties

Poly(arylether benzoxazole)s (PAEBOs) were prepared from a series of fully aromatic dicarboxylic acids containing (phenylenedioxy)diphenylene or (naphthalenedioxy) diphenylene groups and 3,3′‐dihydroxy‐4,4′‐diaminobiphenyl (I) or 4‐4′‐(hexafluoroisopropylidene)bis(2‐aminophenol) (II) through high‐temperature direct polycondensation. A phosphorous pentoxide/methanesulfonic acid mixture or trimethylsilylpolyphosphate was used as a condensing agent. All the PAEBOs were amorphous and soluble in strong acids, and those derived from II were also readily soluble in polar organic solvents. Flexible films were cast from their chloroform solutions. The PAEBOs showed inherent viscosity values of 0.68–2.06 dL/g (CH₃SO₃H, T = 30 °C, c = 0.15 g · dL⁻¹). Thermal analysis indicated glass‐transition temperatures ranging from 236 to 270 °C and thermal stability (5% weight loss) in nitrogen up to 526 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1172–1178, 2000     

Thiol–ene polymerizations using imide‐based monomers

New diene and dithiol monomers, based on aromatic imides such as benzophenone‐3,3′,4,4′‐tetracarboxylic diimide were synthesized and used in thiol‐ene polymerizations which yield poly(imide‐co‐thioether)s. These linear polymers exhibit limited solubility in various organic solvents. The molecular weights of the polymers were found to decrease with increasing imide content. The glass transition temperature (T_g) of these polymers is dependent on imide content, with T_g values ranging from ?55 °C (with no imide) up to 13 °C (with 70% imide). These thermal property improvements are due to the H‐bonding and rigidity of the aromatic imide moieties. Thermal degradation, as studied by thermogravimetric analysis, was not significantly different to the nonimide containing thiol‐ene polymers made using trimethyloylpropane diallyl ether and 3,5‐dioxa‐1,8‐dithiooctane. It is expected that such monomers may lead to increased glass transition temperatures in other thiol‐ene polymer systems as these normally exhibit low glass transition temperatures. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4637–4642     

Highly refractive polymer resin derived from sulfur‐containing aromatic acrylate

New sulfur‐containing polymers with high‐refractive indices and low birefringences have been developed as UV‐curable high‐refractive polymer resins. The polymers derived from 2,7‐bis[(2‐acryloylethyl)sulfanyl]thianthrene (2,7‐BAST) and 4,4′‐bis[(acryloyloxyethylthio)diphenylsulfide (4,4′‐BADS) were prepared by photopolymerization under UV irradiation. Transparent UV‐cured films were obtained in both cases. Both polymers showed good thermal stability, such as a 5% weight‐loss temperature at 355 °C under nitrogen and glass transition temperatures (T_g) in the range of 94–143 °C. They also showed high‐refractive indices of 1.6531 and 1.6645 at 632.8 nm and low birefringences of 0.0039 and 0.0069 in addition to high transparency in the visible region. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2604–2609, 2010     

Synthesis of polyphenylquinoxaline copolymers via aromatic nucleophilic substitution reactions of an A‐B quinoxaline monomer

A self‐polymerizable quinoxaline monomer (A‐B) has been synthesized and polymerized via aromatic nucleophilic substitution reactions. An isomeric mixture of self‐polymerizable quinoxaline monomers—2‐(4‐hydroxyphenyl)‐3‐phenyl‐6‐fluoroquinoxaline and 3‐(4‐hydroxyphenyl)‐2‐phenyl‐6‐fluoroquinoxaline—was polymerized in N‐methyl‐2‐pyrrolidinone (NMP) to afford high molecular weight polyphenylquinoxaline (PPQ) with intrinsic viscosities up to 1.91 dL/g and a glass‐transition temperature (T_g) of 251 °C. A series of comonomers was polymerized with A‐B to form PPQ/polysulfone (PS), PPQ/polyetherether ketone (PEEK), and PPQ/polyethersulfone (PES) copolymers. The copolymers readily obtained high intrinsic viscosities when fluorine was displaced in NMP under reflux. However, single‐electron transfer (SET) side reactions, which limit molecular weight, played a more dominant role when chlorine was displaced instead of fluorine. SET side reactions were minimized in the synthesis of PPQ/PS copolymers through mild polymerization conditions in NMP for longer polymerization times. Thus, the T_g's of PES (T_g = 220 °C), PEEK (T_g = 145 °C), and PS (T_g = 195 °C) were raised through the incorporation of quinoxaline units into the polymer. Copolymers with high intrinsic viscosities resulted in all cases, except in the case of PPQ/PEEK copolymers when 4,4′‐dichlorobenzophenone was the comonomer. © 2001 John Wiley & Sons, Inc. J Polym Sci A Part A: Polym Chem 39: 2037–2042, 2001     

Synthesis and characterization of a series of wholly aromatic copolyesters containing 2‐(α‐phenylisopropyl)hydroquinone moiety

Two series of new wholly aromatic thermotropic copolyesters containing the 2‐(α‐phenylisopropyl)hydroquinone (PIHQ) moiety have been synthesized and their basic properties such as glass transition temperature (T_g), melting temperature (T_m), thermal stability, crystallinity, and liquid crystallinity were studied by differential scanning calorimetry (DSC), thermogravimetry (TG), and wide‐angle X‐ray diffractometry (WAXD) and on a polarizing microscope. The first series was prepared from acetylated PIHQ, terephthalic acid (TPA), and 2,6‐naphthalenedicarboxylic acid (NDA), and the second series from acetylated PIHQ, TPA, and 1,1′‐biphenyl‐4,4′‐dicarboxylic acid (BDA). The T_g values (152–168°C) of the two series are not much different, although the values for the first series appear slightly higher. The T_m values (287–378°C) and the degree of crystallinity of the first series are appreciably greater than those of the second series. Such differences can be explained by the geometric structure of NDA and BDA moieties. All of the present polyesters are thermotropic and nematic. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 881–889, 1999