Viscoelastic behavior of polypropylene/nitrile rubber thermoplastic elastomer blends: Application of Kerner's models for reactively compatibilized and dynamically vulcanized systems

The viscoelastic properties of binary blends of nitrile rubber (NBR) and isotactic polypropylene (PP) of different compositions have been calculated with mean‐field theories developed by Kerner. The phase morphology and geometry have been assumed, and experimental data for the component polymers over a wide temperature range have been used. Hashin's elastic–viscoelastic analogy principle is used in applying Kerner's theory of elastic systems for viscoelastic materials, namely, polymer blends. The two theoretical models used are the discrete particle model (which assumes one component as dispersed inclusions in the matrix of the other) and the polyaggregate model (in which no matrix phase but a cocontinuous structure of the two is postulated). A solution method for the coupled equations of the polyaggregate model, considering Poisson's ratio as a complex parameter, is deduced. The viscoelastic properties are determined in terms of the small‐strain dynamic storage modulus and loss tangent with a Rheovibron DDV viscoelastometer for the blends and the component polymers. Theoretical calculations are compared with the experimental small‐strain dynamic mechanical properties of the blends and their morphological characterizations. Predictions are also compared with the experimental mechanical properties of compatibilized and dynamically cured 70/30 PP/NBR blends. The results computed with the discrete particle model with PP as the matrix compare well with the experimental results for 30/70, 70/30, and 50/50 PP/NBR blends. For 70/30 and 50/50 blends, these predictions are supported by scanning electron microscopy (SEM) investigations. However, for 30/70 blends, the predictions are not in agreement with SEM results, which reveal a cocontinuous blend of the two. Predictions of the discrete particle model are poor with NBR as the matrix for all three volume fractions. A closer agreement of the predicted results for a 70/30 PP/NBR blend and the properties of a 1% maleic anhydride modified PP or 3% phenolic‐modified PP compatibilized 70/30 PP/NBR blend in the lower temperature zone has been observed. This may be explained by improved interfacial adhesion and stable phase morphology. A mixed‐cure dynamically vulcanized system gave a better agreement with the predictions with PP as the matrix than the peroxide, sulfur, and unvulcanized systems. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1417–1432, 2004     

Dynamic mechanical behavior of acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) blends

The dynamic mechanical behavior of uncrosslinked (thermoplastic) and crosslinked (thermosetting) acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) (NBR/EVA) blends was studied with reference to the effect of blend ratio, crosslinking systems, frequency, and temperature. Different crosslinked systems were prepared using peroxide (DCP), sulfur, and mixed crosslink systems. The glass‐transition behavior of the blends was affected by the blend ratio, the nature of crosslinking, and frequency. sThe damping properties of the blends increased with NBR content. The variations in tan δ_max were in accordance with morphology changes in the blends. From tan δ values of peroxide‐cured NBR, EVA, and blends the crosslinking effect of DCP was more predominant in NBR. The morphology of the uncrosslinked blends was examined using scanning electron and optical microscopes. Cocontinuous morphology was observed between 40 and 60 wt % of NBR. The particle size distribution curve of the blends was also drawn. The Arrhenius relationship was used to calculate the activation energy for the glass transition of the blends, and it decreased with an increase in the NBR content. Various theoretical models were used to predict the modulus of the blends. From wide‐angle X‐ray scattering studies, the degree of crystallinity of the blends decreased with an increasing NBR content. The thermal behavior of the uncrosslinked and crosslinked systems of NBR/EVA blends was analyzed using a differential scanning calorimeter. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1556–1570, 2002     

Characterization of elastomeric blends by atomic force microscopy

The bulk mechanical properties of a blend of elastomers are found to depend on the micro and nano scale morphology of the phases of the materials in the blend. In this study, we examine the phase morphology of blends of incompatible elastomers using Atomic Force Microscopy (AFM). Specifically, nanoindentation and Tapping Mode AFM (TMAFM) imaging techniques are used as experimental tools for mapping the composition of unfilled elastomeric blends. Depending on the composition of the blend, either co‐continuous or discontinuous domain/matrix morphology is observed. To identify the different components in bromobutyl (BIIR)/natural rubber (NR) blends, nanoscale indentation measurements were made on the observed phase‐separated regions. Results from force mode AFM and mechanical measurements of bulk NR and BIIR are used to assist in the interpretation of the TMAFM results for the BIIR/NR blends. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 492–503, 2006     

Physical properties and structure of a poly(styrene-co-butadiene) rubber/poly(acrylonitrile-co-butadiene) rubber latex mixture film

The physical properties and the structure of a poly(styrene-co-butadiene) rubber (SBR) and poly(acrylonitrile-co-butadiene) rubber (NBR) latex mixture film are studied in relation to the composition of SBR/NBR for optimization as the precursor of a polymer electrolyte. The composition of SBR50/NBR50 is most suitable in terms of mechanical strength and ionic conductivity. The relationship between the mechanical strength and the structure is analyzed using a simple equivalent mechanical model modified from the Takayanagi model. Our model gives better agreement with experimental results and extends the range of validity of the model to the cocontinuous phase type morphologies. It is possible to estimate the mechanical strength from the continuity of the mechanical supporting phase, calculated from the mechanical model. The tensile properties are found to be strongly affected by the fragile component. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2493–2501, 1998     

Dynamic mechanical properties of isotactic polypropylene/nitrile rubber blends: Effects of blend ratio,reactive compatibilization,and dynamic vulcanization

The effect of blend ratio and compatibilization on dynamic mechanical properties of PP/NBR blends was investigated at different temperatures. The storage modulus of the blend decreased with increase in rubber content and shows two T_g's indicating the incompatibility of the system. Various composite models have been used to predict the experimental viscoelastic data. The Takayanagi model fit well with the experimental values. The addition of phenolic modified polypropylene (Ph-PP) and maleic modified polypropylene (MA-PP) improved the storage modulus of the blend at lower temperatures. The enhancement in storage modulus was correlated with the change in domain size of dispersed NBR particles. The effect of dynamic vulcanization using sulfur, peroxide, and mixed system on viscoelastic behavior was also studied. Among these peroxide system shows the highest modulus. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 2309–2327, 1997     

Effect of compatibilizer on morphology and properties of HDPE/Nylon 6 blends

The compatibilization effect of linear low‐density polyethylene‐grafted maleic anhydride (LLDPEgMA) and high‐density polyethylene‐grafted maleic anhydride (HDPEgMA) on high‐density polyethylene (HDPE)/polyamide 6 (Nylon 6) blend system is investigated. The morphology of 45 wt %/55 wt % polyethylene/Nylon 6 blends with three compatibilizer compositions (5 wt %, 10 wt %, and 15 wt %) are characterized by atomic force microscopic (AFM) phase imaging. The blend with 5 wt % LLDPEgMA demonstrates a Nylon 6 continuous, HDPE dispersed morphology. Increased amount of LLDPEgMA leads to sharp transition in morphology to HDPE continuous, Nylon 6 dispersed morphology. Whereas, increasing HDPEgMA concentration in the same blends results in gradual morphology transition from Nylon 6 continuous to co‐continuous morphology. The mechanical properties, oxygen permeability, and water vapor permeability are measured on the blends which confirm the morphology and indicate that HDPEgMA is a better compatibilizer than LLDPEgMA for the HDPE/Nylon 6 blend system. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 281–290     

Effect of sol–gel derived in situ silica on the morphology and mechanical behavior of natural rubber and acrylonitrile butadiene rubber blends

Silica particles were generated and grown in situ by sol–gel method into rubber blends comprised of natural rubber (NR) and acrylonitrile butadiene rubber (NBR) at various blend ratios. Silica formed into rubber matrix was amorphous in nature. Amount of in situ silica increased with increase in natural rubber proportion in the blends during the sol–gel process. Morphology studies showed that the generated in situ silica were nanoparticles of different shapes and sizes mostly grown into the NR phase of the blends. In situ silica filled NR/NBR blend composites showed improvement in the mechanical and dynamic mechanical behaviors in comparison to those of the unfilled and externally filled NR/NBR blend composites. For the NR/NBR blend at 40/60 composition, in particular, the improvement was appreciable where size and dispersion of the silica particles into the rubber matrix were found to be more uniform. Dynamic mechanical analysis revealed a strong rubber–in situ silica interaction as indicated by a positive shift of the glass transition temperature of both the rubber phases in the blends.     

Preparation and characterization of thermoplastic elastomer of poly(vinyl chloride) and chlorinated waste rubber

In order to develop applications for the abundant waste rubber powder, chlorinated waste rubber (Cl-WR) was prepared by a water based chlorination method using chlorine as chlorinating agent. In this paper, Cl-WR was used as an elastic filler and blended with poly(vinyl chloride) (PVC) matrix to develop a new thermoplastic elastomer PVC/Cl-WR. The mechanical properties, hydrophilicity, swelling resistance, morphology and thermal properties of PVC/Cl-WR were characterized and compared with those of PVC/waste rubber powder (PVC/WR) blends. The results indicated that the mechanical properties, hydrophilicity, swelling resistance and thermal properties of the PVC/Cl-WR blends showed noticeable improvements over PVC/WR blends due to the improved polarity of Cl-WR. Also, the excellent miscibility and compatibility of Cl-WR with PVC was demonstrated by scanning electron microscope (SEM) images of the resulting blends.     

聚合物共混物脆韧转变性能研究 V.橡胶粒子的分布对聚氯乙烯/丁腈橡胶共混物韧性刚性关系的影响

聚合物共混物脆韧转变性能研究Ｖ．橡胶粒子的分布对聚氯乙烯／丁腈橡胶共混物韧性刚性关系的影响刘浙辉朱晓光张学东漆宗能（中国科学院化学研究所工程塑料国家重点实验室北京１０００８０）蔡忠龙（香港理工大学应用物理系香港九龙）王佛松（中国科学院北京...     

Investigation on crosslinking behaviors of NBR/PVC filled with anhydrous copper sulfate particles by dynamic mechanical analysis

Crosslinking behaviors of acrylonitrile butadiene rubber (NBR)/poly (vinyl chloride) (PVC) alloy, filled with anhydrous copper sulfate (CuSO₄) particles, were investigated for the first time by dynamic mechanical analysis (DMA) under hetero and isothermal modes, respectively. In the heterothermal testing, (NBR/PVC)/CuSO₄ compound showed two marked increases in the storage modulus (E′), corresponding to coordination crosslinking of NBR-CuSO₄ and self-crosslinking of NBR and PVC respectively. During the isothermal testing, a dramatic increase in E′ was found at the initial stage while that of original NBR/PVC alloy was not detected. The marked increase in E′ of (NBR/PVC)/CuSO₄ compound was mainly due to the crosslinking induced by coordination between  CN and Cu²⁺. The increasing extent of E′ increased with the rise of CuSO₄ content, suggesting the formation of a greater number of crosslinks. Moreover, the activation energy (E_a) of crosslinking process was about 139 kJ/mol. In this work, fourier transform infrared spectrum (FT-IR) and equilibrium swelling method were also performed for the characterization of the compound. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 41–51, 2007     

Melt rheology and morphology of thermoplastic elastomers from polyethylene/nitrile‐rubber blends: The effect of blend ratio,reactive compatibilization,and dynamic vulcanization

A study of the melt‐rheological behavior of thermoplastic elastomers from high‐density polyethylene and acrylonitrile butadiene rubber (NBR) blends was carried out in a capillary rheometer. The effect of the blend ratio and shear rate on the melt viscosity reveals that the viscosity decreases with the shear rate but increases with NBR content. Compatibilization by maleic anhydride modified polyethylene has no significant effect on the blend viscosity, but a finer dispersion of the rubber is obtained, as is evident from scanning electron micrographs. The melt‐elasticity parameters, such as the die swell, principal normal stress difference, recoverable shear strain, and elastic shear modulus of the blends, were also evaluated. The effect of annealing on the morphology of the extrudate reveals that annealing in the extruder barrel results in the coalescence of rubber particles in the case of the incompatible blends, whereas the tendency toward agglomeration is somewhat suppressed in the compatibilized blends. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1104–1122, 2000     

Studies of photooxidative degradation of poly(vinyl chloride)/poly(ethylene oxide) blends

The photooxidative degradation of blends (in a full range of compositions) of amorphous poly(vinyl chloride) (PVC) with semicrystalline poly(ethylene oxide) (PEO) in the form of thin films is investigated using absorption spectroscopy (UV–visible and Fourier transform infrared) and atomic force microscopy (AFM). The amount of insoluble gel formed as a result of photocrosslinking is estimated gravimetrically. It is found that the PVC/PEO blendsí susceptibility to photooxidative degradation differs from that pure of the components and depends on the blend composition and morphology. Photoreactions such as degradation and oxidation are accelerated whereas dehydrochlorination is retarded in blends. The photocrosslinking efficiency in PVC/PEO blends is higher than in PVC; moreover, PEO is also involved in this process. AFM images showing the lamellar structure of semicrystalline PEO in the blend lead to the conclusion that the presence of PVC does not disturb the crystallization process of PEO. The changes induced by UV irradiation allow the observation of more of the distinct PEO crystallites. This is probably caused by recrystallization of short, more mobile chains in degraded PEO or by partial removal of the less stable amorphous phase from the film surface. These results confirm previous information on the miscibility of PVC with PEO. The mechanism of the interactions between the components and the blend photodegradation are discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 585–602, 2004     

Effect of Electron Beam Irradiation and Ethylene Vinyl Acetate Copolymer on the Properties of NBR/HDPE Blends

The mechanical and physical properties of blends based essentially on nitrile butadiene rubber (NBR) and different ratios of high density polyethylene (HDPE) up to 25 parts per hundred part of rubber (phr) before and after electron beam irradiation were investigated. The values of tensile strength (TS), tensile modulus at 50% elongation (M₅₀), hardness and gel fraction % (GF%) of NBR/HDPE blends were increased with both irradiation dose and by increasing the content of HDPE in the blends. On the other hand, the values of elongation at break (E _b ) were decreased with both irradiation dose and the content of HDPE in the blends. By loading NBR/HDPE (100/25) blend with ethylene vinyl acetate (EVA) copolymer the mechanical and physico-chemical properties were improved. Moreover, the degree of improvement is proportional to the loading content of EVA.     

Novel in situ coordination copper sulfate/ acrylonitrile–butadiene rubber composite

A novel rubber composite of acrylonitrile–butadiene rubber (NBR) filled with anhydrous copper sulfate (CuSO₄) particles was investigated. Dynamic mechanical analysis, differential scanning calorimetry, X‐ray photoelectron spectroscopy, tensile testing, and an equilibrium swelling method were used for the characterization of this novel CuSO₄/NBR composite. The results indicated that the composite had wonderful mechanical properties, which profited from the in situ coordination crosslinking interactions between the nitrile groups (? CN) of NBR and solid CuSO₄ particles. Scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, and transmission electron microscopy results showed that CuSO₄ particles played two roles, acting as both crosslink agents and reinforcing fillers in the matrix. The double actions of CuSO₄ gave the CuSO₄/NBR composites their excellent mechanical properties. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 571–576, 2007     

Transition from crazing to shear deformation in ABS/PVC blends

ABS/PVC blends were prepared over a range of compositions by mixing PVC, SAN, and PB‐g‐SAN. All samples were designed to have a constant rubber level of 12 wt % and the ratio of total‐SAN to PVC in the matrix of the blends varied from 70.5/17.5 to 18/80. Transmission electron microscope and scanning electron microscope have been used to study deformation mechanisms in the ABS/PVC blends. Several different types of microscopic deformation mechanisms, depending on the composition of blends, were observed for the ABS/PVC blends. When the blend is a SAN‐rich system, the main deformation mechanisms were crazing of the matrix. When the blend is a PVC‐rich system, crazing could no longer be detected, while shear yielding of the matrix and cavitation of the rubber particles were the main mechanisms of deformation. When the composition of blend is in the intermediate state, both crazing and shear yielding of matrix were observed. This suggests that there is a transition of deformation mechanism in ABS/PVC blends with the change in composition, which is from crazing to shear deformation. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 687–695, 2006     

聚氯乙烯－丁腈橡胶－氯丁橡胶三元共混物的研究

测定了聚氯乙烯（ＰＶＣ）－丁腈橡胶（ＮＢＲ－２９）－氯丁橡胶（ＣＲ）三元共混物的冲击性能和应力－应变行为，用动态力学分析、扫描电镜和透射电镜研究了共混物的相容性和形态结构，结果表明，ＮＢＲ－２９对ＰＶＣ，ＣＲ有良好的增容作用，三元共混物是部分相容的二相体系，具有良好的抗冲击性能。     

Development and characterization of reactive extruded PVC/polyacrylate blends

This paper describes a method to obtain polymer blends by the absorption of a liquid solution of monomer, initiator, and a crosslinking agent in suspension type porous poly(vinyl chloride) (PVC) particles, forming a dry blend. These PVC/monomer dry blends are reactively polymerized in a twin‐screw extruder to obtain the in situ polymerization in a melt state of various blends: PVC/poly(methyl methacrylate) (PVC/PMMA), PVC/poly(vinyl acetate) (PVC/PVAc), PVC/poly(butyl acrylate) (PVC/PBA) and PVC/poly(ethylhexyl acrylate) (PVC/PEHA). Physical PVC/PMMA blends were produced, and the properties of those blends are compared to reactive blends of similar compositions. Owing to the high polymerization temperature (180°C), the polymers formed in this reactive polymerization process have low molecular weight. These short polymer chains plasticize the PVC phase reducing the melt viscosity, glass transition and the static modulus. Reactive blends of PVC/PMMA and PVC/PVAc are more compatible than the reactive PVC/PBA and PVC/PEHA blends. Reactive PVC/PMMA and PVC/PVAc blends are transparent, form single phase morphology, have single glass transition temperature (T_g), and show mechanical properties that are not inferior than that of neat PVC. Reactive PVC/PBA and PVC/PEHA blends are incompatible and two discrete phases are observed in each blend. However, those blends exhibit single glass transition owing to low content of the dispersed phase particles, which is probably too low to be detected by dynamic mechanical thermal analysis (DMTA) as a separate T_g value. The reactive PVC/PEHA show exceptional high elongation at break (～90%) owing to energy absorption optimized at this dispersed particle size (0.2–0.8 µm). Copyright © 2005 John Wiley & Sons, Ltd.     

Studies on phase morphology and thermo-physical properties of nitrile rubber blends

The study deals with the morphological and thermal analysis of binary rubber blends of acrylonitrile-co-butadiene rubber (NBR) with another polymer. Either ethylene propylene diene terpolymer (EPDM), ethylene vinyl acetate (EVA), chlorosulphonated polyethylene (CSM), or polyvinyl chloride (PVC) has been selected for the second phase. Depending on the relative polarity and interaction parameter of the components, the binary blends showed development of a bi-phasic morphology through scanning electron microscopy (SEM). Use of different types of thermal analysis techniques revealed that these blends are generally incompatible excepting one of NBR and PVC. Derivative differential scanning calorimetry (DDSC), in place of conventional DSC, has been used to characterize the compatibility behavior of the blends. NBR–PVC shows appearance of only one glass transition temperature (T _g) averaging the individual T _g’s of the blend components. The partially missible blend of NBR and CSM shows a broadening of T _g interval between the phase components, while the immiscible blends of either NBR–EPDM or NBR–EVA do not show any change in T _g values corresponding to the individual rubbers of their blend. The experimental T _g values were also compared with those calculated theoretically by Fox equation and observed to match closely with each other. Studies have also been made to evaluate the thermal stability of these blends by thermo-gravimetric analysis (TG) and evaluation of activation energy of respective decomposition processes by Flynn and Wall method. Thermo-mechanical analysis (TMA) was found to be effective for comparison of creep recovery and dimensional stability of the blends both at sub-ambient as well as at elevated temperatures.     

Thermal characterization of nitrile butadiene rubber (NBR)/PVC blends

Summary Nitrile butadiene rubber (NBR) and NBR/PVC blends were produced using 2,2,4-trimethyl-1,2-dihydroquinoline (TMQ) or not as antioxidant. Controlled ozone degradation was performed in several samples. Thermal, compositional and morphological analysis was performed by means of differential scanning calorimetry, thermogravimetry, chemical analysis and scanning electron microscopy. Thermogravimetry analysis shows four mass loss processes related to plastizicer, complex rubber degradation and metallic oxides and other additives. In NBR (NBR/PVC blends) the onset temperature of the first degradation process varies between 227-231°C (259-262°C) and the apparent activation energy between 26 and 36 kJ mol^-1 (36-57 kJ mol^-1), the NBR/PVC samples non degraded presents the higher thermal stability.     

偶联剂对聚氯乙烯－聚丙撑碳酸酯共混体系力学性能的影响

偶联剂对聚氯乙烯－聚丙撑碳酸酯共混体系力学性能的影响王胜杰，黄玉惠，丛广民（中国科学院广州化学研究所广州５１０６５０）关键词聚氯乙烯，聚丙撑碳酸酯，偶联剂，丁腈胶，过氧化苯甲酰，共混聚氯乙烯（ＰＶＣ）是用量巨大的通用塑料，其软性制品需用大量的增塑剂，...