药物和蛋白质与聚己内酯分层复合纳米纤维的微观结构与力学特性

应用同轴共纺技术制得芯质和表层为两种不同材料的分层复合纳米纤维.分别以乙酰螺旋酶素片剂和明胶蛋白质为芯质材料,以可生物降解的聚己内酯作为表层材料,研究了这种分层复合纳米纤维的微观结构与力学特性.结果表明,尽管药物与表层聚合物材料的溶解溶剂互不相同,但仍可以将药物包覆在壁厚小于100nm的超细纤维中.这种纤维可用作体内手术伤口缝合线或大面积创伤如烧伤伤口的敷布.在实验范围内,纤维膜的力学性能随芯质内溶质含量的提高而降低.     

Preparation of biocompatible system based on electrospun CMC/PVA nanofibers as controlled release carrier of diclofenac sodium

Nanofibers of naturally modified polymer such as carboxymethyl cellulose (CMC) blended with poly(vinyl alcohol) (PVA) at different ratios was obtained by electrospinning technique. The blended solutions of CMC and PVA loaded with and without diclofenac sodium (DS) were electrospun using environmentally benign electrospinning technique in the absence of organic solvents. Scanning electron microscopy (SEM), Fourier transform infrared (FTIR), thermogravimetric analysis (TGA) were used to investigate the surface morphology functional groups, as well as the thermal stability of DS loaded CMC/PVA nanofibers mat. The mechanical properties of the as prepared electrospun nanofibers was also evaluated. The entrapment efficiency and the in vitro release of DS loaded CMC/PVA nanofibers were characterized using UV-Vis spectroscopy. The obtained results displayed that the blended nanofibers have shown a smooth morphology, no beads formation when the concentration of CMC was equal or below 5% and beads formation above 5%. FTIR data demonstrated that there were good interactions between CMC and PVA possibly via the formation of hydrogen bonds. The electrospun blended CMC/PVA nanofibers exhibit good mechanical properties. From the in vitro release data, it was found that with the presence of CMC, the release of DS from the nanofibers mats became sustained controlled. Due to the biocompatibility and low cost of the two blended polymers (CMC and PVA), the blended nanofibers system can be considered as one of the promising materials for the preparation of excellent drug carrier.     

Double‐layered composite nanofibers and their mechanical performance

Continuous polymer nanofibers are available through electrospinning, but most have the same structure in their cross section. This article focuses on the fabrication and the structural and mechanical characterization of pencil‐like double‐layered composite nanofibers coaxially electrospun from solutions of two different biodegradable materials, i.e., gelatin and poly(ε‐caprolactone) (PCL). Transmission electron microscopy and water contact angle measurements confirmed that a gelatin inner fiber was wrapped with a PCL outer layer. Possible applications of such nanofibers include a controlled degradation rate when used as a medical device in human body. It has been found that the tensile performance of the composite nanofibers was better than those of both the pure constituent, i.e. gelatin and PCL, nanofibers alone. The ultimate strength and ultimate strain of the composite nanofibers with 7.5% w/v gelatin in the core and 10% w/v PCL as shell were at least 68% and 244% higher, respectively, than those of the same concentration pure gelatin and PCL nanofibers. Thus, a coaxial electrospinning technique as used in this article can be applicable, not only in developing functionalized nanofibers but also in elevating their mechanical property. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2852–2861, 2005     

同轴静电纺丝法制备ZnO/Ag2O纳米纤维材料及其光电催化性能研究

以醋酸锌和乙酰丙酮银为前驱体, 通过同轴静电纺丝和热处理过程在氟掺杂氧化锡(FTO)导电玻璃上制备了ZnO/Ag₂O同轴纳米纤维. 采用X射线衍射(XRD)、 X射线光电子能谱(XPS)、 扫描电子显微镜(SEM)、 透射电子显微镜(TEM)、 拉曼光谱和紫外-可见漫反射光谱(UV-Vis DRS)等手段对材料进行了表征. 以氙灯模拟可见光光源, 亚甲基蓝为目标降解物, 考察了所制备纳米纤维的光电催化活性. 结果表明, 同轴ZnO/Ag₂O纳米纤维具有壳核类似结构(ZnO为壳, Ag₂O为核), Ag₂O与ZnO形成的异质结和杂质能级降低了ZnO的带隙能, 提高了对可见光的利用率. 在可见光下, 与纯ZnO相比, ZnO/Ag₂O具有很强的光电催化能力, 并且Ag₂O的量对同轴纤维光电催化活性影响很大, 在同样光电催化条件下, ZnO/Ag₂O-7同轴纳米纤维的光电催化效果最好, 亚甲基蓝降解率达93%, 动力学常数最大为1.13×10 ^-2 min ^-1.     

Reverse Thinking of the Aggregation-Induced Emission Principle: Amplifying Molecular Motions to Boost Photothermal Efficiency of Nanofibers**

Using reverse thinking of the aggregation-induced emission (AIE) principle, we demonstrate an ingenious and universal protocol for amplifying molecular motions to boost photothermal efficiency of fibers. Core–shell nanofibers having the olive oil solution of AIE-active molecules as the core surrounded by PVDF-HFP shell were constructed by coaxial electrospinning. The molecularly dissolved state of AIE-active molecules allows them to freely rotate and/or vibrate in nanofibers upon photoexcitation and thus significantly elevates the proportion of non-radiative energy dissipation, affording impressive heat-generating efficiency. Photothermal evaluation shows that the core–shell nanofibers with excellent durability can reach up to 22.36 % of photothermal conversion efficiency, which is 26-fold as the non-core–shell counterpart. Such a core–shell fiber can be used for photothermal textiles and solar steam generation induced by natural sunlight with green and carbon-zero emission.     

Poly(glycerol sebacate) nanofiber scaffolds by core/shell electrospinning

The novel biomaterial poly(glycerol sebacate) (PGS) holds great promise for tissue engineering and regenerative medicine. PGS is a rubbery, degradable polymer much like elastin; however, it has been limited to cast structures. This work reports on the formation of PGS nanofibers in random non-woven mats for use as tissue engineering scaffolds by coaxial core/shell electrospinning. PGS nanofibers are an inexpensive and synthetic material that mimics the chemical and mechanical environment provided by elastin fibers. Poly(lactide) was used as the shell material to constrain the PGS during the curing process and was removed before cell seeding. Human microvascular endothelial cells from skin (HDMEC) were used to evaluate the in-vitro cellular compatibility of the PGS nanofiber scaffolds. [Figure: see text].     

Interface hydrogen-bonded core-shell nanofibers by coaxial electrospinning

Core-shell nanofibers were prepared by coaxial electrospinning technology,with poly(ethylene oxide) (PEO) as the core while poly(acrylic acid) (PAA) as the shell.PEO and PAA can form polymer complexes based on hydrogen bonding.In order to avoid forming strong hydrogen bonding complexes at nozzle and blocking spinning process,a polar aprotic solvent,N,N-dimethylformamide (DMF),was selected to dissolve PEO and PAA respectively.SEM,TEM and DSC were utilized to characterize the morphology and structure of PEO-PAA core-shell nanofibers.FTIR spectra demonstrated that hydrogen bonding was formed at the core-shell interface.In addition,the PAA shell of the nanofibers can be cross-linked by ethylene glycol (EG) under heat treatment,which increases the stability and extends the potential applications in aqueous environment.     

Controlled release of doxorubicin from electrospun MWCNTs/PLGA hybrid nanofibers

In this study, multiwalled carbon nanotubes (MWCNTs) were used to encapsulate a model anticancer drug, doxorubicin (Dox). Then, the drug-loaded MWCNTs (Dox/MWCNTs) with an optimized drug encapsulation percentage were mixed with poly(lactide-co-glycolide) (PLGA) polymer solution for subsequent electrospinning to form drug-loaded composite nanofibrous mats. The structure, morphology, and mechanical properties of the formed electrospun Dox/PLGA, MWCNTs/PLGA, and Dox/MWCNTs/PLGA composite nanofibrous mats were characterized using scanning electron microscopy (SEM), Fourier transform infrared spectroscopy, and tensile testing. In vitro viability assay and SEM morphology observation of mouse fibroblast cells cultured onto the MWCNTs/PLGA fibrous scaffolds demonstrate that the developed MWCNTs/PLGA composite nanofibers are cytocompatible. The incorporation of Dox-loaded MWCNTs within the PLGA nanofibers is able to improve the mechanical durability and maintain the three-dimensional structure of the nanofibrous mats. More importantly, our results indicate that this double-container drug delivery system (both PLGA polymer and MWCNTs are drug carriers) is beneficial to avoid the burst release of the drug and able to release the antitumor drug Dox in a sustained manner for 42 days. The developed composite electrospun nanofibrous drug delivery system may be used as therapeutic scaffold materials for post-operative local chemotherapy.     

Direct electrochemistry and voltammetric determination of midecamycin at a multi-walled carbon nanotube coated gold electrode

Magnesium l-ascorbic acid 2-phosphate (MAAP) and α-tocopherol acetate (α-TAc), as the stable vitamin C and vitamin E derivative, respectively, are often applied to skin care products for reducing UV damage. The encapsulation of MAAP (0.5%, g/mL) and α-TAc (5%, g/mL) together within the polyacrylonitrile (PAN) nanofibers was demonstrated using a coaxial electrospinning technique. The structure and morphology characterizations of the core-shell fibers MAAP/α-TAc-PAN were investigated by SEM, FTIR and XRD. As a negative control, the blend nanofibers MAAP/α-TAc/PAN were prepared from a normal electrospinning method. The results from SEM indicated that the morphology and diameter of the nanofibers were influenced by concentration of spinning solution, the polymer component of the shell, the carrying agent of the core and the fabricating methods, and the core-shell nanofibers obtained at the concentration of 8% had finer and uniform structure with the average diameters of 200 ± 15 nm. From in vitro release studies it could be seen that both different fiber specimens showed a gradual increase in the amount of α-TAc or MAAP released from the nanofibers. Furthermore, α-TAc and MAAP released from the blend nanofibers showed the burst release at the maximum release of ～15% and ～40% during the first 6 h, respectively, but their release amount from the core-shell nanofibers was only 10–12% during the initial part of the process. These results showed that core-shell nanofibers alleviated the initial burst release and gave better sustainability compared to that of the blend nanofibers. The present study would provide a basis for further optimization of processing conditions to obtain desired structured core-shell nanofibers and release kinetics for practical applications in dermal tissue.     

Preparation of polyamide-6/chitosan composite nanofibers by a single solvent system via electrospinning for biomedical applications

This work was focused on preparation and characterizations of chitosan blended polyamide-6 nanofibers by a new single solvent system via electrospinning process for human osteoblastic (HOB) cell culture applications. The morphological, structural and thermal properties of the polyamide-6/chitosan nanofibers were analyzed by using field-emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), Fourier transform-infrared (FT-IR) spectroscopy, Raman spectroscopy, differential scanning calorimetry (DSC) and thermogravimetry (TGA). SEM images revealed that the nanofibers were well-oriented and had good incorporation of chitosan. FT-IR results indicated that the amino groups of chitosan existed in the blended nanofibers. TGA analysis revealed that the onset degradation temperature was decreased with increasing chitosan content in the blended nanofibers. The morphological features of the cells attached on nanofibers were confirmed by SEM. The adhesion, viability and proliferation properties of osteoblast cells on the polyamide-6/chitosan blended nanofibers were analyzed by in vitro cell compatibility test.     

将源药包覆到聚己内酯超细纤维的芯部

采用同轴共纺技术,分别将白藜芦醇(Resveratrol,RT)和硫酸庆大霉素(Gentamycin Sulfate,GS)源药包覆在生物可降解的聚己内酯(PCL)超细(直径为几百纳米)纤维芯部.研究了这种纤维的制备过程以及它们的微观结构.这种复合纳米纤维可在医疗新产品开发中发挥作用,如用于制备新的羊肠线(体内手术伤口缝合线)或伤口敷布.     

Fabrication,characterization and in vivo evaluation of dexpanthenol sustained-release nanofibers for wound healing

In this study, wound dressings consisting of dexpanthenol (Dex)-loaded electrospun nanofibers were fabricated using polyvinyl alcohol (PVA)/sodium alginate (SA), and chitosan as the core and the shell, respectively. Considering the remarkable properties of chitosan, it was used as a shell against drug release and to improve the thermal stability, and tensile strength of the scaffold. By comparing the thermogravimetric, and tensile strength results of nanofibers with and without shell, it was revealed that the presence of chitosan in the shell side could improve the thermal stability and increased the tensile strength by about three times. The isotherm models of dexpanthenol release from the PVA/SA/Dex-CS scaffold was best described by the Langmuir model. Besides, Fourier transform infrared, scanning electron microscopy, and X-ray diffraction techniques were performed to characterize nanofibers. Furthermore, an in vivo investigation of a wound dressing with dexpanthenol showed better healing compared to the wound dressings without dexpanthenol.     

Electrospinning Process of Thermo-sensitive Poly(N-isopropylacrylamide) /poly (2-acrylamido-2-methylpropanesulfonic acid) Nanofibers

Poly (N-isopropylacrylamide)/poly (2-acrylamido-2-methylpropanesulfonic acid) (PNIPAAm/PAMPS) nanofibers was prepared using the electrospinning technique. The electrospinning process parameters such as solution concentration, voltage, receiver distance and flow rate were determined by the orthogonal experiments. The appropriate electrospinning parameters were 7.0% of solution concentration, 10.0 kV of voltage, 20 cm of distance and 3.1 μL·min^?1 of flow rate, respectively. The major factor affecting the nanofibers diameter was the solution concentration and the diameter increased with the solution concentration. The Fourier-transform infrared spectroscopy (FTIR) was conducted to characterize the structure of the components for electrospinning. Scanning electron microscopy (SEM) was taken to observe the morphology, and the contact angle (CA) measuring was carried out to determine the wettability of the nanofibers with temperatures. The results of SEM observation showed that the surfaces of nanofibers were smooth with uniform fibrous diameters and without the formation of beads. The CA detections showed that the electrospun PNIPAAm/PAMPS nanofibers exhibited thermo-sensitivity of hydrophilicity at 20°C and hydrophobicity at 40°C.     

Synthesis,Characterization, and Photocatalytic Properties of Ag/TiO2 Composite Nanofibers Prepared by Electrospinning

Ag nanoparticles (Ag NPs) embedded titanium dioxide (TiO₂) nanofibers were fabricated by colloidal sol process, electrospinning, and calcination technique. Calcination of the electrospun nanofibers were heat treated at 600°C for 180 minutes in air atmosphere. X-ray diffraction patterns exhibited that the anatase phase and silver coexisted in the resulted Ag NPs/TiO₂ nanofibers; transmission electron microscopy demonstrated Ag NPs well spread in the porous microstructure of composite fibers. The prepared nanofibers were utilized as photocatalyst for degradation of methyl orange. The degradation rate of methyl orange dye solution containing Ag/TiO₂ composite nanofibers is 99% only after irradiation for 3 hours. It is proposed that these new Ag NPs/TiO₂ composite nanofibers will have potential application in water pollution treatment.      

Electrospun nanofibers for drug delivery applications: Methods and mechanism

Electrospinning procedures such as blend electrospinning, coaxial electrospinning, and emulsion electrospinning have been used for the fabrication of electrospun nanofibers (ENFs) for biomedical applications. These ENFs are attracted great interest especially in drug delivery applications due to their small size, high surface area-to-volume, and porosity. The aim of this review is to focus on the controlled release mechanism among the different electrospinning methods, and the selectivity of hydrophilic, water-soluble polymers as a carrier for drug. The mechanism for the drug delivery depends mainly on the method of drug loading, polymeric interactions, and the nature of polymer swelling, erosion, or degradation. This review compressed on the literature survey about the fabrication of nanofibers by different electrospinning methods, factors affecting the nanofiber morphologies, selectivity of polymeric blends for successful controlled release behavior, and the mechanism involved in the drug release steps.     

Polysulfone nanofibers prepared by electrospinning and gas/jet-electrospinning

Polysulfone nanofibers were prepared by electrospinning. The electrospinning equipment was designed in a new way, wherein the spinneret was combined with a gas jet device. The intrinsic viscosity of the used polysulfone was 0.197 dL/g in dimethyl acetamide, which was also the solvent in electrospinning. The gas used in this gas jet/electrostatic spinning was nitrogen. The relationship between the process parameters and the average diameter of polysulfone nanofibers was investigated. The main process parameters studied in this work were the voltage, the flow rate of the spinning fluid, the distance between the spinneret and the nanofiber collector and the temperature in the spinning chamber. The other important factors determining the nanometer diameter were the spinning fluid properties including its viscosity, surface tension and electrical conductivity. The average diameter and the diameter distribution of electrospinning nanofibers were measured experimentally by using scanning electron microscopy. The diameter of polysulfone nanofibers prepared by the gas jet/electrostatic spinning was in the range 50–500 nm. It was found that the diameter of nanofibers mainly depended on high voltage, the gap between the spinneret and the collector and the concentration of polymer solutions. It is concluded that the gas-jet/electrospinning is a better method than the conventional electrospinning, in that it makes the nanofibers finer and more uniform and exhibits higher efficiency in the process of electrospinning. __________ Translated from Acta Polymerica Sinica, 2005, (5) (in Chinese)     

Core–shell structure PEO/CS nanofibers based on electric field induced phase separation via electrospinning and its application

Core–shell structured PEO‐chitosan nanofibers have been produced from electric field inducing phase separation. Chitosan, a positive charged polymer, was dissolved in 50 wt % aqueous acetic acid and the amino group on polycation would protonize, which would endow chitosan electrical properties. Chitosan molecules would move along the direction of the electric field under the electrostatic force and formed the shell layer of nanofibers. Preparation process of core – shell structure is quite simple and efficient without any post‐treatment. The core–shell structure and existence of chitosan on the shell layer were confirmed before and after post‐treatment by TEM and further supported by SEM, FTIR, XRD, DSC, and XPS studies. Blending ratio of PEO and chitosan, molecular weight of chitosan for the mobility of chitosan are thought to be the key influence factors on formation of core–shell structure. Drug release studies show that the prepared core–shell structure nanofibers has a potential application in the biomedical fields involving drug delivery. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2298–2311     

Electrospinning nanofibers of microbial polyhydroxyalkanoates for applications in medical tissue engineering

Differently to most chemically synthesized medical materials, polyhydroxyalkanoates (PHAs) are intracellular carbon and energy storage granules, which is a family of natural bio-polymers synthesized by microorganism's materials. Due to excellent biocompatibility reasonable biodegradability and versatile material difference, PHAs are well medical biomaterials candidates for applications in tissue engineering and drug delivery, including commercial PHB, PHBV, PHBHHx, PHBVHHx, P34HB and few uncommercial PHAs. Electrospinning nanofibers with the size of 10–10,000 nm can improve the mechanical properties and decrease the crystallinity of PHA, meanwhile simulate the structure and function of native extracellular matrix of cells. Hence, PHAs electrospinning nanofibers as engineered scaffolds have been widely used for tissue engineering scaffolds in cardiovascular, vascular, nerve, bone, cartilage and skin; also, as carriers for application in drug delivery system. In this review, we highlight the extraction and properties of medical PHAs from natural or engineered microorganism, and microstructure, current manufacturing techniques and medical applications of electrospinning nanofibers of PHAs. Moreover, the current challenges and prospects of PHAs electrospinning nanofibers are discussed rationally, providing an insight into developing vibrant fields of PHAs electrospinning nanofibers-based biomedicine.     

Hyaluronic Acid (HA)‐Based Silk Fibroin/Zinc Oxide Core–Shell Electrospun Dressing for Burn Wound Management

Burn injuries represent a major life‐threatening event that impacts the quality of life of patients, and places enormous demands on the global healthcare systems. This study introduces the fabrication and characterization of a novel wound dressing made of core–shell hyaluronic acid–silk fibroin/zinc oxide (ZO) nanofibers for treatment of burn injuries. The core–shell configuration enables loading ZO—an antibacterial agent—in the core of nanofibers, which in return improves the sustained release of the drug and maintains its bioactivity. Successful formation of core–shell nanofibers and loading of zinc oxide are confirmed by transmission electron microscopy, Fourier‐transform infrared spectroscopy, and energy dispersive X‐ray. The antibacterial activity of the dressings are examined against Escherichia coli and Staphylococcus aureus and it is shown that addition of ZO improves the antibacterial property of the dressing in a dose‐dependent fashion. However, in vitro cytotoxicity studies show that high concentration of ZO (>3 wt%) is toxic to the cells. In vivo studies indicate that the wound dressings loaded with ZO (3 wt%) substantially improves the wound healing procedure and significantly reduces the inflammatory response at the wound site. Overall, the dressing introduced herein holds great promise for the management of burn injuries.     

Cable-Like Core–Shell Mesoporous SnO2 Nanofibers by Single-Nozzle Electrospinning Phase Separation for Formaldehyde Sensing

In this study, we have developed a simple and efficient single-nozzle electrospinning strategy involving the phase separation of polystyrene and poly(vinylpyrrolidone) to construct cable-like core–shell mesoporous SnO₂ nanofibers. Compared with traditional multi-axial electrospinning approaches to the synthesis of core–shell nanofibers, the single-nozzle electrospinning process requires no complex multi-axial electrospinning setups or post-treatments, just drying and annealing after electrospinning. The obtained SnO₂ nanofibers show promise as a sensing material for formaldehyde at low concentrations, the detection limit being about 1 ppm. Furthermore, the nanofibers exhibited good cycling stability and selectivity, with response and recovery times toward 10 ppm formaldehyde being approximately 18 and 196 s, respectively, at an operating temperature of 195 °C.