Ammonium persulfate-initiated polymerization of cationic starch-grafted-cationic polyacrylamide flocculant for the enhanced flocculation of oil sludge suspension

In this study, a novel, highly efficient and environmentally friendly flocculant, namely, cationic starch-grafted-cationic polyacrylamide (CS-g-CPAM), was synthesized by initiation polymerization of ammonium persulfate. First, CS-g-CPAM was polymerized with cationic starch(CS), acrylamide(AM) and diallyl dimethyl ammonium chloride (DMDAAC), and then the influence factors of graft polymerization were investigated, including total monomer concentration, initiator dosage, the monomer mass ratio of m_AM: m_CS: m_DMDAAC, post-polymerization temperature and post-polymerization time. And the intrinsic viscosity of the CS-g-CPAM was measured by the one point method accurately. The chemical structures and morphology of the samples were characterized by Fourier transform-infrared spectroscopy (FT-IR), X-ray diffraction (XRD), thermo-gravimetric and differential scanning calorimetry (TG-DSC), and scanning electron microscope (SEM). The CS-g-CPAM was utilized to flocculate the oil sludge suspension, the effects of CS-g-CPAM dosage, temperature and pH value on the flocculation performance were investigated. The results show that CS-g-CPAM has outstanding flocculation effect.     

Nanofiltration membrane cross‐linked by m‐phenylenediamine for dye removal from textile wastewater

In this work, m‐phenylenediamine (MPD) is used to prepare cross‐linked polyetherimide (PEI)‐based nanofiltration (NF) membrane for treatment of dye containing wastewater. The effects of dope solution composition, cross‐linking time, and dye concentration on membrane performance are investigated. Results indicate that the rejection of dye is increased with the increase of acetone concentration in the dope solution, cross‐linking time, and dye concentration. Meanwhile, membrane flux showed the opposite trend. With the aid of SEM and FTIR analysis, the cross‐linking between MPD and PEI is confirmed. The cross‐linked membrane has thicker and dense selective layer compared to the unmodified membrane. The cross‐linked NF membrane (PEI: 15 wt%; acetone: 20 wt%; cross‐linking time: 10 minutes) showed good performance in filtration of synthetic dye wastewater (Reactive Red 120, 1500 ppm) with 98% dye rejection and 0.013 L m^?2 hour^?1 of flux at relatively low operating pressure (60 psi).     

Novel Metal‐Polyurethane Complexes with Enhanced Antimicrobial Activity

Summary: The silver coating of polymers has been intensively investigated in the last few decades as an effective non‐resistance‐inducing strategy to prevent medical device‐related infections. We have developed a completely new approach to incorporate silver ions in polymers by the synthesis of a carboxylated polyurethane able to coordinate Ag⁺. The obtained polymers possess mechanical properties suitable for the development of medical devices, without any risk of loss of activity. To minimize the risk of increasing antibiotic resistance, the metal ion‐containing polymers are loaded with ciprofloxacin, which possesses a different mechanism of antimicrobial action, thus a system able to inhibit Staphylococcus epidermidis and Pseudomonas aeruginosa growth for at least one month is developed.

SEM images showing a mature S. epidermidis biofilm on the surface of the carboxylated polyurethane (left) and the surface of the silver ion‐containing polyurethane free from bacterial colonization (right) after 48 h of incubation.     

An NMR investigation of the interaction of polyethylene oxide with water‐soluble poly(vinyl phenol‐co‐potassium styrene sulfonate)

The water‐soluble complex of polyethylene oxide (PEO) with poly (vinyl phenol‐co‐potassium styrene sulfonate) (PVPh‐co‐KSS) was studied by liquid‐state NMR. PEO showed two peaks in the ¹H spectra, which corresponded to the free and complexed PEO. The ratio of the free PEO/complexed PEO was decreased with the increase in the mixing ratio of PVPh‐co‐KSS/PEO. Some of the complex formation disappeared when the pH was raised from 6.4 to 12.0. It had been thought that at high pH, the phenolic groups dissociate and thus cannot form hydrogen bonds. The fact that NMR indicates some interaction at pH 12.0 implies there are some other interactions, such as hydrophobic interactions between the aromatic rings and the polyether methylene groups, contributing to PEO and PVPh‐co‐KSS complex formation. Nuclear Overhauser effect (NOE) cross peaks were observed between PEO and the aromatic protons of PVPh‐co‐KSS in nuclear Overhauser effect spectra (NOESY) suggesting that the distance between PEO and the aromatic protons of PVPh‐co‐KSS was less than 5 Å. The exchange between the complexed PEO and the free PEO was slow on the NMR time scale. The ratio of the integral of the complexed PEO to the free PEO increased with temperature, indicating that the number of PEO segments interacting with the aromatic ring increases with temperature. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1276–1284, 2000     

Side‐chain glycylglycine‐based polymer for simultaneous sensing and removal of copper(II) from aqueous medium

Since glycylglycine (Gly‐Gly) residue in the N‐terminal region of human prion protein, a copper binding protein, binds with Cu(II), N‐terminus Gly‐Gly side‐chain containing water soluble block copolymer was synthesized and used for simultaneous sensing and removal of Cu(II) ion from aqueous medium. The polymer has amide nitrogen atom and ester carbonyl group as potential binding sites in the side‐chain Gly‐Gly pendants. Job's plot experiment confirms 2:1 binding stoichiometry of polymer with Cu(II). This polymer is able to sense parts per billion level of Cu(II) very selectively in an aqueous medium and remove Cu(II) ions quantitatively by precipitating out the Cu(II) via complex formation in the pH range 7–9. The binding mode of polymer with Cu(II) in polymer‐Cu(II) complex was characterized by ¹H NMR, FTIR, and UV–vis spectroscopy. The attachment of Cu(II) in the polymer‐Cu(II) complex was confirmed by cyclic voltammetry experiment. Cu(II) release from the complex was achieved at pH 5 due to the protonation of amide nitrogen atoms in the Gly‐Gly moiety. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 914–921     

Coordination of nickel and copper dithiolate to 2,2′‐bipyridine‐based π‐conjugated polymers

π‐Conjugated polymers (Poly1–Poly3) containing a 2,2′‐bipyridine (bpy) unit were subjected to coordination to nickel and copper dithiolate for the purpose of manipulating the photophysical properties. The absorption maximum peak of Poly1 [maximum wavelength (λ_max) = 446 nm] redshifted by 36 nm upon the coordination of bpy to NiCl₂, which produced Poly1–NiCl₂. A further bathochromic shift was observed in the spectrum of Poly1–mntNi [mntNi = (maleonitrile dithiolate)nickel; λ_max = 499 nm] bearing the dithiolate ligand, which stemmed from the extension of the conjugated system over the nickel dithiolate moiety through the bpy unit. An increase in the [Ni]/[bpy] ratio in Poly1–mntNi rendered the original maximum peak at 446 nm smaller and the lower energy charge‐transfer peak at 499 nm larger; the isosbestic points remained at 380 and 475 nm. The green fluorescence (λ_max = 504 nm) emitted from Poly1 markedly diminished upon the coordination of nickel dithiolate because of the effective energy transfer. The absorption maximum peak of Poly1–mntNi in chloroform at 499 nm blueshifted to 471 nm when the volume ratio of the chloroform/N,N‐dimethylformamide solvent reached 10:90. The coordination of nickel dithiolate to Poly2 and Poly3 also brought about redshifts of the absorption maximum peaks of as much as 55 and 61 nm, respectively. The absorption maximum peak of Poly1–(phenyldithiolate)nickel(pdtNi) (λ_max = 474 nm) redshifted by 28 nm in comparison with that of Poly1, whereas the magnitude of the shift of Poly1–bis(thiophenoxide)nickel(btpNi) bearing two thiophenoxide ligands was 20 nm. Poly1–mntCu with a tetrahedral copper center was also investigated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2631–2639, 2004     

Iridium complex grafted to 3,6‐carbazole‐alt‐tetraphenylsilane copolymers for blue electrophosphorescence

We designed a 3,6‐dibromo‐9‐hexyl‐9H‐carbazole derivative with the blue emissive iridium complex bis[2‐(4,6‐difluorophenyl)pyridyl‐N,C^2′](picolinato)iridium(III) (FIrpic) linked at the alkyl terminal. Based on this monomer, novel 3,6‐carbazole‐alt‐tetraphenylsilane copolymers grafted with FIrpic were synthesized by palladium‐catalyzed Suzuki coupling reaction, and the content of FIrpic in the polymers could be controlled by feed ratio of the monomers. The polymer films mainly show blue emission from FIrpic, and the emission intensity from the polymer backbones is much weaker compared with the doped analogues, which demonstrates an efficient energy transfer from polymeric host to covalently bonded guest. The phase separation in the polymers was suppressed, which can be identified by atomic force microscopy and designed electroluminescent (EL) devices. EL devices based on the polymers exhibited blue phosphorescence from FIrpic. The luminous efficiency of preliminary devices reached 2.3 cd/A, and the efficiency roll‐off at high current densities was suppressed. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1859–1865, 2010     

Preparation of nano‐chitosan Schiff‐base copper complexes and their anticancer activity

A new kind of nano‐chitosan Schiff‐base Cu complexes with particle sizes of 350 nm were prepared by combination of nano‐chitosan, Cu and Schiff‐base, and characterized by FT‐IR spectra, TEM, DLS and elemental analysis. The modes and mechanism of interaction of the copper complexes with DNA were studied by the fluorescent probe method and electrophoresis analysis. The results suggest that the Cu complexes bound to DNA by electrostatic and intercalation modes. The anticancer activity of the Cu complexes was evaluated by Sulforhodamine B (SRB) assay in vitro. Nano‐chitosan and their Schiff‐base Cu complexes inhibited the growth of the liver cancer cell lines SMMC‐7721 in vitro. The inhibition rate of Schiff‐base Cu complexes was higher than that of nano‐chitosan. Nano‐chitosan combining with Schiff‐base and Cu improved their anticancer activity, which ascribed to the synergistic effect between the chitosan matrix and the planar construction of the Cu complexes. Copyright © 2008 John Wiley & Sons, Ltd.     

Synthesis and performances for treating oily wastewater produced from polymer flooding of new demulsifiers based on polyoxyalkylated N,N‐dimethylethanolamine

Usually, oily wastewater produced from polymer flooding (OWPF) was treated by cationic polymer in oilfield. In this paper, six block copolymers of ethylene oxide and propylene oxide were prepared by using N,N‐dimethylethanolamine (DMEA) as the acceptor (DMEA‐mnp and DMEA‐mnpq, n:m:p:q represented the weight ratio of different blocks). Most of DMEA products could perform well for treating OWPF, especially DMEA1231. Their performances were mainly affected by temperature. The reason of increasing oil removal performance of DMEA1231 with temperature was the decrease of interfacial dilational modulus (ε) with increasing temperature. When temperature raised up to 55°C, the ε of DMEA1231 had the minimum (1.5 l mN/m). Therefore, the OiW had the minimum (90 mg/l). Because DMEA1231 had the best performance, its flocculation kinetics was studied systemically. The results showed that the optimum condition for DMEA1231 was as follows: dosage was 300 mg/l, temperature was 55°C, stirring speed was 200 rpm and stirring time was 5 min. At last, the offshore oil field test was carried out to check the DMEA1231 performance. The result showed that at the optimum condition, DMEA1231 could perform as well as the cationic polymer. The most important thing was that flocs of DMEA1231 were not viscous and floated on the surface of the water. The results obtained by this paper provide a good choice for the treatment of OWPF in offshore oilfield to avoid the formation of viscous flocs. Copyright © 2014 John Wiley & Sons, Ltd.     

Synthesis and magnetic properties of poly(p‐phthaloyl‐disacetylaceton‐ethylenediimine) metal complexes

Macrocyclic Schiff‐base ligand, bisacetylaceton‐ethylenediimine (BAE) and its transition metal complexes M(BAE) (M = Cu²⁺, Ni²⁺) were synthesized. The complexes having characteristics of aromatic systems and well‐defined one‐dimensional structures, reacted with p‐phthaloyl chloride, to obtain polymer complexes. The complexes were characterized by elemental analysis, inductively coupled plasma (ICP), FT‐IR, and thermal analysis and show good thermal stability. ESR spectra analysis discovered that there are free radicals in the chain of polymers, indicating that a weak magnetic spin‐exchange interaction operates between the metal ions and free radicals. It is found that, as the bridging p‐phthaloyl group is able to propagate the magnetic exchange interaction, the polymer complexes show paramagnetic properties by measurement of temperature dependence of the magnetic property, and obey Curie–Weiss law. Copyright © 2001 John Wiley & Sons, Ltd.     

Multifunctional materials based on polyazomethines derived from 2,5‐dihydroxy‐1,4‐benzoquinone and siloxane diamines

New polyazomethines have been synthesized by the reaction between 2,5‐dihydroxy‐1,4‐benzoquinone and siloxane diamines differing by the siloxane sequence length. A dimer has also been prepared as a model compound. The products were characterized by spectral (FTIR and ¹H‐NMR) and elemental analyses, GPC, viscosity measurements, solubility tests, and transmission electron microscopy (TEM). The different properties have been investigated by adequate techniques: thermal (DSC and TGA), spectral (UV–vis and fluorescence spectroscopy), redox (Differential Pulse Voltammetry). pH‐sensitivity and metal complexing ability were also evaluated. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1862–1872, 2008     

Poly(4‐vinylpyridine) as the host ligand of metal‐containing chromophores for second‐order nonlinear optical active materials

Two formulas of grafted polymers with metal‐containing chromophores, potentially suitable for second‐order nonlinear optics applications, are described. Two chromophores were obtained from a tridentate ligand coordinated to Cu(II) or Pd(II) ions. The organometallic chromophore fragments were grafted to poly(4‐vinylpyridine) by the pyridinic nitrogen of the host polymer. Some qualities displayed by the new metallated polymers are remarkable: (1) a high value of the first hyperpolarizability coefficient of the chromophores, (2) a high content of the grafted chromophore in the polymers (up to 60 wt %), (3) a considerable increase in the glass‐transition temperatures (up to 240 °C), (4) good thermal stability in air (ca. 280 °C), and (5) good optical transparency of the films. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2987–2993, 2002     

Metallo‐Supramolecular Diethylene Glycol: Water‐Soluble Reversible Polymers

Bis(2,2′:6′,2″‐terpyrid‐4′‐yl) diethylene glycol was synthesized as a monomer unit and further utilized for polymerization with FeCl₂ in order to form water‐soluble coordination polymers. Viscosity measurements and film‐forming properties indicate the formation of linear coordination polymers or larger ring structures. The terpyridine/iron(II) complexes are stable up to temperatures of 210 °C, but can be uncomplexed by the addition of an excess of a strong competitive ligand (HEDTA) under mild conditions.

     

Preparation of a Yb(III)‐Incorporated porous polymer by post‐Coordination: Enhancement of gas adsorption and catalytic activity

We synthesized a Yb(III)‐incorporated microporous polymer (Yb‐ADA) and studied its gas adsorption property and catalytic activity. The adamantane‐based porous polymer (ADA) was obtained from an ethynyl‐functionalized adamantane derivative and 2,5‐dibromoterephthalic acid through Sonogashira–Hagihara cross‐coupling. ADA had two carboxyl groups which were used for Yb(III) coordination under basic conditions. The Brunauer‐Emmett‐Teller (BET) surface area of ADA was 970 m² g^?1. As Yb(III) ions were incorporated into ADA, the surface area of the polymer (Yb‐ADA) was reduced to 885 m² g^?1. However, Yb‐ADA exhibited a significantly enhanced CO₂ adsorption capacity despite the reduction of surface area. The CO₂ uptakes of ADA and Yb‐ADA were 1.56 and 2.36 mmol g^?1 at 298 K, respectively. The H₂ uptake of ADA also increased after coordination with Yb(III) from 1.15 to 1.40 wt % at 77 K. Yb‐ADA showed high catalytic activity in the acetalization of 4‐bromobenzaldehyde and furfural with trimethyl orthoformate and could be reused after recovery without severe loss of activity. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5291–5297     

Synthesis and characterization of water‐soluble barbiturate‐ and thiobarbiturate‐functionalized polystyrene

The synthesis and characterization of barbiturate‐ and thiobarbiturate‐functionalized polystyrene from polystyrene homopolymer by polymer‐modification reactions is discussed. Polystyrene homopolymer quantitatively functionalized at the para postion with diethyl oxomalonate functionality was subjected to a condensation reaction with urea and thiourea in the presence of sodium methoxide in methanol. This reaction proceeded essentially to quantitative conversion to the barbiturate‐ (BAPS) and thiobarbiturate‐functionalized polystyrenes (TBAPS) as estimated by ¹H NMR, UV, and IR spectroscopies. Thus, several copolymers of styrene with barbiturate‐ and thiobarbiturate‐functionalized styrene were synthesized. The detailed characterizations of quantitatively functionalized polystyrene using gel permeation chromatographic, IR, UV, and ¹H NMR spectroscopic techniques as well as thermogravimetric analysis are discussed. An application of the newly synthesized polymer in removing Cu(II) ions from aqueous solution is demonstrated. This is the first report on the synthesis of BAPS and TBAPS by the polymer‐modification route or otherwise. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 731–737, 2002; DOI 10.1002/pola.10154     

New less toxic zeolite‐encapsulated Cu(II) complex nanomaterial for dual applications in biomedical field and wastewater remediation

A new dual‐functional Cu(II) complex and its nanohybrid form encapsulated into NaY zeolite cavities were synthesized. The synthesized compounds were characterized using elemental analyses, X‐ray fluorescence, infrared, ¹H NMR, electronic, electron spin resonance and mass spectra, powder X‐ray diffraction, surface area and transmission electron microscopy in addition to conductivity and magnetic susceptibility measurements. The encapsulated Cu(II) complex was catalytically tested for degradation of industrial wastewater. The decolorization and mineralization results indicate that the Cu(II) complex encapsulated into zeolite host is an effective heterogeneous catalyst for real industrial wastewater remediation. In addition, both free and encapsulated Cu(II) complexes were tested as anti‐microbial and anti‐tumour agents. The results show that the Cu(II) complex encapsulated into zeolite has a high activity (IC₅₀ = 14.4 μg ml^?1). The results of in vivo toxicity experiments indicate that the Cu(II) complex encapsulated into zeolite is a less toxic biocompatible material (LD₅₀ = 1245 mg kg^?1). The catalytic properties, cytotoxicity and toxicity of the new nanohybrid Cu(II) complex encapsulated into zeolite make it a promising eco‐friendly and biocompatible material for water remediation and biomedical applications.     

A novel crystal structure of {tris[4‐(1H‐pyrazol‐3‐yl‐κN2)‐3‐azabut‐3‐enyl]amine‐κN}iron(II) bis(tetrafluoridoborate) methanol monosolvate featuring a low‐spin configuration

Mononuclear complexes are good model systems for evaluating the effects of different ligand systems on the magnetic properties of iron(II) centres. A novel crystal structure of the title compound, [Fe(C₁₈H₂₄N₁₀)](BF₄)₂·CH₃OH, with one molecule of methanol per formula unit exhibits a strictly sixfold coordination sphere associated with a low‐spin configuration at the metal centre. The incorporated methanol solvent molecule promotes extended hydrogen‐bonding networks between the tetrafluoridoborate anions and the cationic units. A less constrained crystal structure regarding close contacts between the tetrafluoridoborate anions and the cationic units allows a spin transition which is inhibited in the previously published hydrate of the title compound.     

Multi‐center nature of ethylene polymerization catalysts based on 2,6‐bis(imino)pyridyl complexes of iron and cobalt

2,6‐Bis(imino)pyridyl complexes of Fe and Co in combination with methylalumoxane form very active homogeneous catalytic systems for polymerization of ethylene. GPC analysis of the polymers prepared with the complexes indicates that the Co complexes produce single‐center catalysts whereas the Fe complexes produce catalysts with numerous types of active centers. Different centers in the latter catalyst systems respond differently to reaction conditions such as the reaction duration, the [MAO]:[Fe] ratio, the ethylene concentration, etc. The article examines the effects of reaction variables on the performance of both types of catalysts and proposes an explanation for the complex behavior of the catalysts derived from the Fe complexes. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6159–6170, 2006     

Multinuclear Non‐Heme Iron Complexes for Double‐Strand DNA Cleavage

Bleomycin mimics : Efficient oxidative double‐strand DNA cleavage has been achieved with multinuclear non‐heme iron complexes (see scheme). These complexes therefore represent model compounds that mimic the mode of action of the anti‐tumor drug bleomycin.