Sonochemical fabrication of fluorinated mesoporous titanium dioxide microspheres

A sonochemical-hydrothermal method for preparing fluorinated mesoporous TiO₂ microspheres was developed. Formation of mesoporous TiO₂ and doping of fluorine was achieved by sonication and then hydrothermal treatment of a solution containing titanium isopropoxide, template, and sodium fluoride. The as-synthesized TiO₂ microspheres were characterized by X-ray diffraction (XRD), Fourier translation infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy-dispersive X-ray (EDX) spectroscopy, photoluminescence spectroscopy (PL), and BET surface areas. The P123 template was removed completely during the hydrothermal and washing steps, which was different from the conventional calcination treatment. The as- synthesized TiO₂ microspheres had good crystallinity and high stability. Results from the photocatalytic degradation of methylene blue (MB) showed that fluorination could remarkably improve the photocatalytic activity of titanium dioxide.     

简易模板剂法制备多级介孔TiO2微球及其在染料敏化太阳能电池中的性能

采用模板剂法一步合成分级结构的介孔TiO₂微球, 考察了烷基胺类模板剂中烷基链长度对介孔TiO₂微球合成及性能影响. 将其应用于染料敏化太阳能电池的光阳极半导体薄膜中, 得到了9.5%-10.1%的高能量转换效率. X射线衍射(XRD)、物理吸附仪(BET)、扫描电镜(SEM)等的分析结果表明: 分级结构介孔TiO₂微球的晶相为纯锐钛矿型; 介孔TiO₂微球表面粗糙, 的纳米粒子堆积形成, 使微球具有介孔性质和较适宜的比表面积. 介孔TiO₂微球堆积形成了利于物质扩散的通道并具有良好的光散射效果; 同时微球介孔粗糙表面保证了染料的大量吸附, 从而提高了电池的光电流. 通过电化学阻抗分析结果验证了分等级结构介孔TiO₂微球光阳极有利于电解液的传输和物质扩散的优异性能.     

锌离子掺杂的二氧化钛介孔空心微球的制备及光催化性能

以二氧化硅为模板,钛酸四丁酯(TBOT)为钛源,硝酸锌为锌源,采用溶胶凝胶法制备了锌离子掺杂的介孔二氧化钛空心微球。采用X射线衍射(XRD)、比表面积(BET)、透射电镜(TEM)、扫描电镜(SEM)和X射线光电子能谱(XPS)等技术对样品进行表征,以亚甲基蓝(MB)的光催化降解为目标反应评价其光催化活性。结果表明,去核之后的复合微球为空心微球,壁厚为20 nm左右。钛酸四丁酯溶液的滴加时间对微球的形貌影响较大,当滴加时间大于15 min时,可以得到结构清晰的空心微球。用氢氧化钠溶液去除二氧化硅核,反应90 min,二氧化硅可以被完全去除。X射线衍射表明,实验得到的掺杂锌离子的空心微球和没有掺杂锌离子的空心微球都是锐钛矿。当锌离子的摩尔分数为0.3%时,二氧化钛空心微球的晶粒尺寸最小,比表面积最大,催化亚甲基蓝降解的效率最高。     

Study on the fabrication and photovoltaic property of TiO2 mesoporous microspheres

Titanium dioxide mesoporous microspheres with high surface area was successfully prepared by a facile one-step hydrothermal approach using polyethylene glycol (PEG, MW 200) as the soft template. Study shows that ∼15 nm TiO₂ nanoparticles was assembled into ∼1.1 μm mesoporous microspheres. The Brunauer-Emmett-Teller surface area of TiO₂ microsphere is up to 137 m²/g. TiO₂ mesoporous microspheres were fabricated onto the surface of fluorine-doped tin oxide glass and used as the photoanode of dye-sensitized solar cells, which exhibits an open circuit photovoltage of 0.80 V and an overall conversion efficiency of 6.6%. Owing to the enhanced dye loading and light-harvesting efficiency, a 26% improvement in the overall conversion efficiency was achieved when compared with the commercial Degussa P₂₅ nanoparticles.     

Mesoporous titania photocatalyst: effect of relative humidity and aging on the preparation of mesoporous titania and on its photocatalytic activity performance

Mesoporous TiO₂ has been synthesized by the sol–gel method, using a nonionic triblock copolymer P123 as surfactant template under acidic conditions. The as-prepared samples were characterized by thermogravimetry–differential thermal analysis (TG–DTA), nitrogen absorption–desorption (BET), field emission scanning electron microscopy, and transmission electron microscopy. The photocatalytic activity of the mesoporous TiO₂ was evaluated by degradation of methylene blue under high-intensity UV light irradiation; the amount of methylene blue was measured by UV–visible spectroscopy. TG–DTA analysis revealed that the surfactant had been removed partly in as-synthesized samples. BET analysis proved that all the samples retained mesoporosity with a narrow pore-size distribution (4.5–6.3 nm) and high surface area (103–200 m²/g). All calcined mesoporous TiO₂ had high photocatalytic activity in the photodegradation of methylene blue.     

Preparation of Anatase Hollow TiO2 Spheres and Their Photocatalytic Activity in the Photodegradation of Chlorpyrifos

Hollow anatase titania (TiO₂) spheres were synthesized using fructose and tetrabutyl titanate (Ti(OC₄H₉)₄, TBT) as the precursors via the conventional hard template method. The morphological, structural and thermal properties of the products were characterized using scanning electron microscopy (SEM), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), Fourier transform infrared (FTIR) spectroscopy, X‐ray diffraction (XRD), thermogravimetric and differential thermal analysis (TG‐DTA), Brunauer? Emmett? Teller (BET) surface area analysis and diffuse reflectance ultraviolet visible (DR UV? Vis) spectroscopy. XRD revealed that the hollow TiO₂ prepared was in the anatase phase and the BET surface area measured was about 22 m² g^?1. The photocatalytic activity of the synthesized hollow anatase TiO₂ in the photodecomposition of chlorpyrifos was 18.67 % higher than that obtained using commercial TiO₂.     

Development of mesoporous TiO2 microspheres with high specific surface area for selective enrichment of phosphopeptides by mass spectrometric analysis

In this study, mesoporous TiO₂ microspheres were synthesized by simple hydrothermal reaction, and successfully developed for phosphopeptides enrichment from both standard protein digestion and real biological sample such as rat brain tissue extract. The mesoporous TiO₂ microspheres (the diameter size of about 1.0 μm) obtained by simple hydrothermal method were found to have a specific surface area of 84.98 m²/g, which is much larger than smooth TiO₂ microspheres with same size. The surface area of mesoporous TiO₂ microspheres is almost two times of commercial TiO₂ nanoparticle (a diameter of 90 nm). Using standard proteins digestion and real biological samples, the superior selectivity and capacity of mesoporous TiO₂ microspheres for the enrichment of phosphorylated peptides than that of commercial TiO₂ nanoparticles and TiO₂ microspheres was also observed. It has been demonstrated that mesoporous TiO₂ microspheres have powerful potential for selective enrichment of phosphorylated peptides. Moreover, the preparation of the mesoporous TiO₂ microspheres obtained by the hydrothermal reaction is easy, simple and low-cost. These mesoporous TiO₂ microspheres with the ability of large scale synthesis can widely be applied for phosphorylated proteomic research.     

Structurally Stabilized Organosilane‐Templated Thermostable Mesoporous Titania

Structurally thermostable mesoporous anatase TiO₂ (m‐TiO₂) nanoparticles, uniquely decorated with atomically dispersed SiO₂, is reported for the first time. The inorganic Si portion of the novel organosilane template, used as a mesopores‐directing agent, is found to be incorporated in the pore walls of the titania aggregates, mainly as isolated sites. This is evident by transmission electron microscopy and high‐angle annular dark field scanning transmission electron microscopy, combined with electron dispersive X‐ray spectroscopy. This type of unique structure provides exceptional stability to this new material against thermal collapse of the mesoporous structure, which is reflected in its high surface area (the highest known for anatase titania), even after high‐temperature (550 °C) calcination. Control of crystallite size, pore diameter, and surface area is achieved by varying the molar ratios of the titanium precursor and the template during synthesis. These mesoporous materials retain their porosity and high surface area after template removal and further NaOH/HCl treatment to remove silica. We investigate their performance for dye‐sensitized solar cells (DSSCs) with bilayer TiO₂ electrodes, which are prepared by applying a coating of m‐TiO₂ onto a commercial titania (P25) film. The high surface area of the upper mesoporous layer in the P25–m‐TiO₂ DSSC significantly increases the dye loading ability of the photoanode. The photocurrent and fill factor for the DSSC with the bilayer TiO₂ electrode are greatly improved. The large increase in photocurrent current (ca. 56 %) in the P25–m‐TiO₂ DSSC is believed to play a significant role in achieving a remarkable increase in the photovoltaic efficiency (60 %) of the device, compared to DSSCs with a monolayer of P25 as the electrode.     

Solvothermal preparation of copper(II) porphyrin-sensitized mesoporous TiO<Subscript>2</Subscript> composites: enhanced photocatalytic activity and stability in degradation of 4-nitrophenol

Four new copper(II) porphyrins CuPp(1, 2, 3, 4) with a different number of peripheral ester groups were synthesized and used to sensitize the mesoporous TiO₂ under solvothermal condition, and accordingly, four mesoporous CuPp(1, 2, 3, 4)/TiO₂ composites were obtained. These composites were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, BET nitrogen adsorption–desorption isotherms (BET), UV–vis diffuse reflectance spectroscopy (UV–vis-DRS), and Fourier-transform infrared spectroscopy (FT-IR). The results showed the crystal structure and morphology of mesoporous TiO₂ were not affected by the porphyrin existence on its surface. The photocatalysis properties of mesoporous TiO₂ and CuPp(1, 2, 3, 4)/TiO₂ have been evaluated by conducting the photocatalytic degradation of 4-nitrophenol (4-NP) under visible-light irradiation, and the result showed their higher photocatalytic activities and the order is: CuPp(4)/TiO₂ > CuPp(3)/TiO₂ > CuPp(2)/TiO₂ > CuPp(1)/TiO₂ ? TiO₂. The probable reasons are their large surface area and different number of peripheral groups in CuPp, which separate electron–hole pairs efficiently. The repetition test of CuPp(1, 2, 3, 4)/TiO₂ composites demonstrated that they still maintained superior photocatalytic activity over six recycles.     

Photocatalytic Activity of Microwave Plasma-Synthesized TiO2 Nanopowder

Nanocrystalline TiO₂ was synthesized using the microwave plasma technique and characterized using X-ray diffraction, transmission electron microscopy, scanning electron microscopy, laser particle size analyzer, UV–vis spectroscopy and BET surface area analyzer. The synthesized TiO₂ powder crystallized in anatase phase and the crystallite sizes were in nanometers. The photocatalytic activity of the compound was determined and compared against the activity of the commercial Degussa P-25 TiO₂ catalyst. The degradation rates of the dyes were found to be higher over the synthesized TiO₂ as compared to that over commercial Degussa P-25 TiO₂.     

Evaluating the efficiency of the GO‐Fe3O4/TiO2 mesoporous photocatalyst for degradation of chlorpyrifos pesticide under visible light irradiation

In this work, the photocatalytic activity of the synthesized graphene oxide (GO)‐Fe₃O₄/TiO₂ mesoporous photocatalysts was evaluated using chlorpyrifos (CP) as a contaminant. The nano‐photocatalyst was characterized by X‐ray diffraction, field emission scanning electron microscopy with energy‐dispersive X‐ray spectroscopy, transmission electron microscopy, and specific surface area by the Brunauer–Emmett–Teller method. Using visible light, the GO‐Fe₃O₄/TiO₂ mesoporous photocatalyst was investigated on the degradation of CP pesticide. The GO‐Fe₃O₄/TiO₂ photocatalyst displayed a good photocatalytic activity, which was achieving 97% of CP degradation after 60 min. Finally, experiments were performed to evaluate GO‐Fe₃O₄/TiO₂ mesoporous nanocatalyst activity on repeated applications; after several uses, its photocatalytic activity was retained, which indicated stability.     

后处理法合成高热稳定性的中孔Ti-P-Al材料

 以阳离子表面活性剂十六烷基三甲基溴化铵(CTAB)为模板剂,采用水热合成法制备了中孔氧化钛原粉,再采用磷酸和氯化铝溶液依次对中孔氧化钛原粉进行后处理,得到了具有高热稳定性的中孔Ti-P-Al材料. 通过粉末X射线衍射、透射电子显微镜和氮物理吸附等方法对样品进行了表征. 结果表明,反应凝胶组成对样品的中孔结构有较大的影响,当反应凝胶配比为Ti(SO4)2∶CTAB∶H2O=1∶0.54∶430, 温度为363 K, 处理时间为10～20 min时,所得的TiO2原粉具有较规整的中孔结构. 此样品经过0.25 mol/L的磷酸处理后有序性有较大程度的提高. 将磷酸处理过的样品进一步用氯化铝溶液处理,得到了中孔结构的Ti-P-Al材料,此材料经过873 K焙烧后仍具有典型的中孔特征,其比表面积为 382 m2/g, 孔径为3.13 nm.     

锌离子掺杂的二氧化钛介孔空心微球的制备及光催化性能

以二氧化硅为模板,钛酸四丁酯（TBOT）为钛源,硝酸锌为锌源,采用溶胶凝胶法制备了锌离子掺杂的介孔二氧化钛空心微球。采用X射线衍射（XRD）、比表面积（BET）、透射电镜（TEM）、扫描电镜（SEM）和X射线光电子能谱（XPS）等技术对样品进行表征,以亚甲基蓝（MB）的光催化降解为目标反应评价其光催化活性。结果表明,去核之后的复合微球为空心微球,壁厚为20nm左右。钛酸四丁酯溶液的滴加时间对微球的形貌影响较大,当滴加时间大于15min时,可以得到结构清晰的空心微球。用氢氧化钠溶液去除二氧化硅核,反应90min,二氧化硅可以被完全去除。X射线衍射表明,实验得到的掺杂锌离子的空心微球和没有掺杂锌离子的空心微球都是锐钛矿。当锌离子的摩尔分数为0.3%时,二氧化钛空心微球的晶粒尺寸最小,比表面积最大,催化亚甲基蓝降解的效率最高。     

Preparation of mesoporous TiO2/CNT nanocomposites by synthesis of mesoporous titania via EISA and their photocatalytic degradation under visible light irradiation

Stabilized mesoporous TiO₂ was synthesized by evaporation induced self assembly (EISA) method and mechanically incorporated into single-walled carbon nanotubes (SWCNT) with different ratios. The physicochemical properties of the nanocomposites (mesoporous TiO₂/SWCNT) materials were investigated by Brunauer–Emmett–Teller (BET) measurement, X-ray diffraction (XRD), transmission electron microscopy (TEM), energy dispersive X-ray (EDX), photoluminescence (PL) and ultraviolet–visible (UV–Vis) spectroscopy measurements. The catalytic activity of mesoporous TiO₂ and nanocomposites were assessed by examining the degradation of rhodamine B as model aqueous solution under visible light. CNTs are facilitating the photocatalytic activity of mesoporous TiO₂ in the degradation of rhodamine B efficiently.     

Low Temperature Solvent Evaporation-induced Crystallization Synthesis of Nanocrystalline TiO2 Photocatalyst

A novel and efficient methodology for obtaining highly active photocatalyst of bi-phase TiO2 with small particle size and high specific surface area was developed by solvent evaporation-in-duced crystallization (SEIC) method at low temperature. The prepared TiO2 powder was characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM) and BET surface areas. The photocatalyfic activity was evaluated by the photocatalyflc oxidation of acetone in air. The results showed that the photocatalytic activity of the TiO2 powder preDared by this method approached that of Degnssa P25. This may be atotributed to the fact that the predated TiO2 powder had larzer specific surface areas (265 m2. g- 1 ) and smaller crystallite size (about 5 nm), but relatively low crystallinity, as compared with Degussa P25.     

Fluorinated Mesoporous Anatase TiO<Subscript>2</Subscript> Microspheres with High Surface and Enhanced Photocatalytic Activity for the Degradation of Methyl Orange

Highly crystalline mesoporous TiO₂ microspheres with areas up to 122 m²/g and tunable pore size have been prepared through a combined sol–gel and solvothermal processes. The concentration of NaF exhibits a great effect on the morphology, crystallinity, crystal size and photocatalytic activity of the TiO₂ microspheres. A higher NaF concentration results in an increase in the average crystal size and pore size, whereas whereas it caused a decrease in the specific surface areas. All fluorinated TiO₂ microspheres showed a higher photocatalytic activity than P25 and pure TiO₂ microspheres obtained in the absence of NaF due to the effect of surface fluorination on the photoactivity of TiO₂. The approach described in this study provides a simple method to synthesize the micrometer-sized hierarchical structure of mesoporous TiO₂ microspheres that are ready for practical applications such as environmental pollutants removal and solar cell because these high active materials can be easily separated.     

Preparation and characterization of SiO2/TiO2 composite microspheres with microporous SiO2 core/mesoporous TiO2 shell

SiO₂/TiO₂ composite microspheres with microporous SiO₂ core/mesoporous TiO₂ shell structures were prepared by hydrolysis of titanium tetrabutylorthotitanate (TTBT) in the presence of microporous silica microspheres using hydroxypropyl cellulose (HPC) as a surface esterification agent and porous template, and then dried and calcined at different temperatures. The as-prepared products were characterized with differential thermal analysis and thermogravimetric (DTA/TG), scanning electron microscopy (SEM), X-ray diffraction (XRD), nitrogen adsorption. The results showed that composite particles were about 1.8 μm in diameter, and had a spherical morphology and a narrow size distribution. Uniform mesoporous titania coatings on the surfaces of microporous silica microspheres could be obtained by adjusting the HPC concentration to an optimal concentration of about 3.2 mmol L⁻¹. The anatase and rutile phase in the SiO₂/TiO₂ composite microspheres began to form at 700 and 900 °C, respectively. At 700 °C, the specific surface area and pore volume of the SiO₂/TiO₂ composite microspheres were 552 and 0.652 mL g⁻¹, respectively. However, at 900 °C, the specific surface area and pore volume significantly decreased due to the phase transformation from anatase to rutile.     

Synthesis of nano‐sized magnetite mesoporous carbon for removal of Reactive Yellow dye from aqueous solutions

In this study, core‐shell structures of magnetite nanoparticles coated with CMK‐8 ordered mesoporous carbon (Fe₃O₄@SiO₂‐CMK‐8 NPs) have been successfully synthesized for the first time by carbonizing sucrose inside the pores of the Kit‐6 mesoporous silica. The nano‐sized mesoporous particles were characterized by X‐ray diffraction, Fourier transform‐infrared spectroscopy, scanning electron microscope, dynamic light scattering, vibrating‐sample magnetometer, Brunauer–Emmett–Teller (BET) and transmission electron microscopy instruments. The obtained nanocomposite was used for removal of Reactive Yellow 160 (RY 160) dye from aqueous samples. The N₂ adsorption–desorption method (at 77 K) confirmed the mesoporous structure of synthesized Fe₃O₄@SiO₂‐CMK‐8 NPs. Also, the surface area was calculated by the BET method and Langmuir plot as 276.84 m²/g and 352.32 m²/g, respectively. The surface area, volume and pore diameter of synthesized nanoparticles (NPs) were calculated from the pore size distribution curves using the Barrett–Joyner–Halenda formula (BJH). To obtain the optimum experimental variables, the effect of various experimental parameters on the dye removal efficiency was studied using Taguchi orthogonal array experimental design method. According to the experimental results, about 90.0% of RY 160 was removed from aqueous solutions at the adsorbent amount of 0.06 g, pH 3 and ionic strength = 0.05 m during 10 min. The pseudo‐second order kinetic model provided a very good fit for the RY 160 dye removal (R² = 0.999). The Langmuir, Freundlich, Temkin and Dubinin–Radushkevich models were applied to describe the equilibrium isotherms, and the Langmuir isotherm showed the best fit to data with the maximum adsorption capacity of 62.893 mg/g. Furthermore, the Fe₃O₄@SiO₂‐CMK‐8 NPs could be simply recovered by external magnet, and exhibited recyclability and reusability for a subsequent six runs.     

Enhanced electron collection in photoanode based on ultrafine TiO2 nanotubes by a rapid anodization process

The separated and ultrafine TiO₂ nanotubes are fabricated by a modified rapid anodization method, which cannot be achieved through conventional anodization. Then, model dye-sensitized solar cells based on the prepared TiO₂ nanotubes and commercial TiO₂ nanoparticles (P25) are investigated, and a discrepancy is discovered between the light-harvesting capability and the power conversion efficiency. The charge transport and recombination are studied by the electrochemical impedance spectroscopy and the open-circuit voltage decay technique. Results show that the nanotube photoanode owns a longer electron diffusion length and a larger electron lifetime than the nanoparticle one, which can compensate for the loss of light absorption. The enhanced electron collection efficiency observed is attributed to the facilitated charge carrier pathways in the photoanode composed by the separated TiO₂ nanotubes fabricated in this work. Therefore, the TiO₂ nanotubes synthesized by this method are verified to have good electronic properties, which might find applications not only in photovoltaic, but also in catalysis, sensors, and other areas.     

Effect of TiCl4‐based TiO2 compact and blocking layers on efficiency of dye‐sensitized solar cells

The effect of the number and arrangement of TiO₂‐based photoanode layers on the efficiency of dye‐sensitized solar cells (DSSCs) was investigated. Compact, mesoporous, and blocking layers of TiO₂ were prepared to form monolayer, bilayer, and trilayer photoanodes. Compact and blocking TiO₂ layers were prepared using dip‐coating technique, whereas the doctor‐blade method was employed to prepare TiO₂ paste layers using nanoparticles prepared by the sol–gel method. The crystalline structure of photoanodes was characterized by X‐ray diffraction (XRD) measurements and their morphology and thickness were characterized by the scanning electron microscopy (SEM) technique. The photovoltaic performance of constructed DSSC devices was investigated and the optimum arrangement was identified and explained in terms of dye loading enhancement and recombination reduction at the fluorine‐doped tin oxide (FTO)/electrolyte interface.