锌离子掺杂的二氧化钛介孔空心微球的制备及光催化性能

以二氧化硅为模板,钛酸四丁酯(TBOT)为钛源,硝酸锌为锌源,采用溶胶凝胶法制备了锌离子掺杂的介孔二氧化钛空心微球。采用X射线衍射(XRD)、比表面积(BET)、透射电镜(TEM)、扫描电镜(SEM)和X射线光电子能谱(XPS)等技术对样品进行表征,以亚甲基蓝(MB)的光催化降解为目标反应评价其光催化活性。结果表明,去核之后的复合微球为空心微球,壁厚为20 nm左右。钛酸四丁酯溶液的滴加时间对微球的形貌影响较大,当滴加时间大于15 min时,可以得到结构清晰的空心微球。用氢氧化钠溶液去除二氧化硅核,反应90 min,二氧化硅可以被完全去除。X射线衍射表明,实验得到的掺杂锌离子的空心微球和没有掺杂锌离子的空心微球都是锐钛矿。当锌离子的摩尔分数为0.3%时,二氧化钛空心微球的晶粒尺寸最小,比表面积最大,催化亚甲基蓝降解的效率最高。     

Towards ultrafine TiO2 nanocrystal at room temperature

Ultrafine titanium dioxide (TiO₂) nanocrystal has attracted enormous interest due to their unusual quantum and surface effects. Here, we propose a facile route to synthesize ultrafine anatase nanocrystal at room temperature via an aqueous sol–gel method using lactic acid (LA) and acetylacetone (Acac) as double chelators. Transmission electron microscopy (TEM) and size analyzer confirmed that TiO₂ nanocrystal in precursor possessed an average size of ~3 nm with a narrow size distribution. Crystal structure characterized by TEM and X-ray diffraction (XRD) indicated that TiO₂ nanocrystal to be anatase phase. The results of field emission scanning electron microscopy (FE-SEM) and BET surface area exhibited that TiO₂ xerogel powder had mono-dispersed particles size and large BET surface area up to 90 m²/g.     

锌离子掺杂的二氧化钛介孔空心微球的制备及光催化性能

以二氧化硅为模板,钛酸四丁酯（TBOT）为钛源,硝酸锌为锌源,采用溶胶凝胶法制备了锌离子掺杂的介孔二氧化钛空心微球。采用X射线衍射（XRD）、比表面积（BET）、透射电镜（TEM）、扫描电镜（SEM）和X射线光电子能谱（XPS）等技术对样品进行表征,以亚甲基蓝（MB）的光催化降解为目标反应评价其光催化活性。结果表明,去核之后的复合微球为空心微球,壁厚为20nm左右。钛酸四丁酯溶液的滴加时间对微球的形貌影响较大,当滴加时间大于15min时,可以得到结构清晰的空心微球。用氢氧化钠溶液去除二氧化硅核,反应90min,二氧化硅可以被完全去除。X射线衍射表明,实验得到的掺杂锌离子的空心微球和没有掺杂锌离子的空心微球都是锐钛矿。当锌离子的摩尔分数为0.3%时,二氧化钛空心微球的晶粒尺寸最小,比表面积最大,催化亚甲基蓝降解的效率最高。     

Preparation,characterization and photocatalytic properties of TiO<Subscript>2</Subscript> nanostructured spheres synthesized by the Sol–Gel method modified with ethylene glycol

Monodispersed nanostructured TiO₂ spheres were obtained by the Sol–Gel method modified with ethylene glycol. The sample morphology and surface textural properties were characterized by X-ray diffraction (XRD), N₂-physisorption, scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA) and diffuse reflectance spectroscopy (DRS). The SEM image showed spheres with sizes ranging from 600 to 700 nm. In addition, HRTEM micrographs reveal hexagonal grains slightly elongated (20 nm). The powders present a BET surface area of 116 m² g⁻¹. Samples without thermal treatment and those treated at 400 °C both showed characteristic reflections of the anatase phase. The photocatalytic activity of the prepared TiO₂ spheres was determined by degradation of 2,4-dichlorophenoxyacetic acid (2,4-D) in aqueous solution. Kinetics parameters have displayed than the nanostructured material present a reaction half-life time of 30 min and it was two times faster than commercial TiO₂ (P25).     

Synthesis of Bi-doped TiO2 Nanotubes and Enhanced Photocatalytic Activity for Hydrogen Evolution from Glycerol Solution

Bi‐doped TiO₂ nanotubes with variable Bi/Ti ratios were synthesized by hydrothermal treatment in 10 mol·L^?1 NaOH (aq.) through using Bi‐doped TiO₂ particles derived from conventional sol‐gel method as starting materials. The effects of Bi content on the morphology, textural properties, photo absorption and photocatalytic activity of TiO₂ nanotubes were investigated. The scanning electron microscopy (SEM), transmission electron microscopy (TEM), X‐ray diffraction (XRD) and X‐ray photoelectron spectroscopy (XPS) observations of the obtained samples revealed the formation of titanate nanotube structure doped with Bi, which exists as a higher oxidation state than Bi³⁺. Bi‐doping TiO₂ nanotubes exhibited an extension of light absorption into the visible region and improved photocatalytic activities for hydrogen production from a glycerol/water mixed solution as compared with pure TiO₂ nanotubes. There was an optimal Bi‐doped content for the photocatalytic hydrogen production, and high content of Bi would retard the phase transition of titanate to anatase and result in morphology change from nanotube to nanobelt, which in turn decreases the photocatlytic activity for hydrogen evolution.     

Photocatalytic Activity of Microwave Plasma-Synthesized TiO2 Nanopowder

Nanocrystalline TiO₂ was synthesized using the microwave plasma technique and characterized using X-ray diffraction, transmission electron microscopy, scanning electron microscopy, laser particle size analyzer, UV–vis spectroscopy and BET surface area analyzer. The synthesized TiO₂ powder crystallized in anatase phase and the crystallite sizes were in nanometers. The photocatalytic activity of the compound was determined and compared against the activity of the commercial Degussa P-25 TiO₂ catalyst. The degradation rates of the dyes were found to be higher over the synthesized TiO₂ as compared to that over commercial Degussa P-25 TiO₂.     

Rapid Synthesis of Mesoporous TiO2 for the Photoanodes in Dye Sensitized Solar Cells

Mesoporous TiO₂ microspheres with high specific surface areas were synthesized by means of a facile one‐step microwave hydrothermal process without using any template. The mesoporous materials were rapidly achieved using TiCl₄, urea and ammonium sulphate at comparatively low microwave power (400 W) for 8 min irradiation. The morphology and microstructure of the as‐prepared products were characterized by field emission scanning electron microscopy (FESEM), X‐ray diffraction (XRD), transmission electron microscopy (TEM) and Brunauer‐Emmett‐Teller (BET) surface area analysis. Structural characterization indicates that the TiO₂ microspheres display mesoporous structure. The average pore sizes and BET surface areas of the spheres were 5.3 nm and 222 m²g^?1, respectively. The mesoporous nanocrystals synthesized at 160 °C for 8 min were then used to prepare the photoanode for dye sensitized solar cells (DSSCs). A high power conversion efficiency of 5.72% was achieved from the mesoporous TiO₂ based photoanode, representing about 25.7% improvement over the efficiency of P25 photoanode.     

Microstructures and photocatalytic properties of Ag and La surface codoped TiO2 films prepared by sol–gel method

Ag⁺ and La³⁺ surface codoped TiO₂ films were successfully prepared by the improved sol–gel and doping processes. The as-prepared specimens were characterized using differential thermal analysis-thermogravimetry (DTA–TG), X-ray diffraction (XRD), high-resolution field emission scanning electron microscopy (FE-SEM), X-ray energy dispersive spectroscopy (EDS), Brunauer–Emmett–Teller (BET) surface area, Photoluminescence spectrum (PL) and UV–vis diffuse reflectance spectroscopy. The photocatalytic activities of the films were evaluated by degradation of an organic dye in aqueous solution. The results of XRD, FE-SEM and BET analyses indicated that the TiO₂ films were composed of nano-particles or aggregates with a size of less than 10 nm. With the codoping of Ag⁺ and La³⁺, TiO₂ films with high photocatalytic activity and clearly responsive to the visible light were obtained. The improvement mechanism by ions doping was also discussed.     

Preparation of Ce‐doped TiO2 Hollow Fibers and Their Photocatalytic Degradation Properties for Dye Compound

Cerium‐doped titanium dioxide (TiO₂) with a hollow fiber structure was successfully prepared using ammonium ceric nitrate and tetrabutyltitanate as precursors and cotton fiber as the template. The effects of cerium (Ce)‐doping on the crystallite sizes, crystal pattern, and optical property of the prepared catalysts were investigated by means of techniques such as scanning electron microscopy (SEM), X‐ray diffraction (XRD), BET surface area, and UV‐vis diffuse absorption spectroscopy. SEM observation showed that the prepared TiO₂ fibers possessed fibrous shape inherited from the cotton fiber and had a hollow structure. As confirmed by XRD and UV‐vis diffuse absorption spectroscopy examinations, Ce‐doping restrained the growth of grain size and extended the photoabsorption edge of TiO₂ hollow fiber into the visible light region. The present photocatalyst showed higher photocatalytic reactivity in photodegradation of highly concentrated methylene blue (MB) solutions than pure TiO₂ under UV and visible light, and the amount of Ce‐doped significantly affected the catalytic property. In the experiment condition, the photocatalytic activity of 0.5 mol% Ce‐doped TiO₂ fiber was optimal of all the prepared samples. In addition, the possibility of cyclic usage of the photocatalyst was also confirmed. The material was easily removed by centrifugal separation. Therefore, using the template method and by doping with cerium, TiO₂ may hopefully become a low‐energy consuming, high activity and green environmentally friendly catalytic material.     

Solar active nano-TiO2 for mineralization of Reactive Red 120 and Trypan Blue: 1st Nano Update

Nano-TiO₂ was synthesized by sol–gel method. The catalyst was characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) images, transmission electron microscope (TEM), BET surface area measurement and DRS analysis. The formation of anatase phase nano-TiO₂ was confirmed by XRD measurements and its crystalline size is found to be 15.2 nm. SEM images depict the crystalline nature of prepared TiO₂. The BET surface area of prepared TiO₂ is found to be 86.5 m² g^?1 which is higher than that of commercially available TiO₂–P25. The photocatalytic activity of prepared anatase phase TiO₂ has been tested for the degradation of two azo dyes: Reactive Red 120 (RR 120) and Trypan Blue (TB) using solar light. The photocatalytic activity of nano-TiO₂ is higher than TiO₂–P25 under solar light. The mineralization of dyes has been confirmed by chemical oxygen demand (COD) measurements.     

Mesoporous titania photocatalyst: effect of relative humidity and aging on the preparation of mesoporous titania and on its photocatalytic activity performance

Mesoporous TiO₂ has been synthesized by the sol–gel method, using a nonionic triblock copolymer P123 as surfactant template under acidic conditions. The as-prepared samples were characterized by thermogravimetry–differential thermal analysis (TG–DTA), nitrogen absorption–desorption (BET), field emission scanning electron microscopy, and transmission electron microscopy. The photocatalytic activity of the mesoporous TiO₂ was evaluated by degradation of methylene blue under high-intensity UV light irradiation; the amount of methylene blue was measured by UV–visible spectroscopy. TG–DTA analysis revealed that the surfactant had been removed partly in as-synthesized samples. BET analysis proved that all the samples retained mesoporosity with a narrow pore-size distribution (4.5–6.3 nm) and high surface area (103–200 m²/g). All calcined mesoporous TiO₂ had high photocatalytic activity in the photodegradation of methylene blue.     

One‐Pot Synthesis of Nitrogen‐doped TiO2 Nanowires with Enhanced Photocurrent Generation

A nitrogen‐doped TiO₂ (N‐TiO₂) nanowire film was synthesized via a one‐pot hydrothermal method using triethylamine as nitrogen source. The effect of the concentration of the triethylamine on the films was evaluated. In addition, the N‐TiO₂ nanowires were characterized using field‐emission scanning electron microscopy (FE‐SEM), X‐ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, and ultraviolet–visible spectroscopy. A 3.2× enhancement of the photocurrent for N‐TiO₂ (0.6) was achieved over the as‐prepared TiO₂ nanowire, under AM1.5G solar illumination. This was due to nitrogen doping, which could narrow the bandgap of titania to extend the adsorption of the catalyst to the visible light region.     

金红石相TiO2-石墨烯复合材料的制备及其光催化性能

以鳞片石墨为原料, 用改进的Hummers法制备氧化石墨烯(GO), 以异丙醇钛为钛源经一步水热法制备得到金红石相TiO₂-石墨烯复合材料(rGO-TiO₂), 考察了氧化石墨烯用量对复合材料光催化性能的影响. 采用X射线衍射(XRD), 比表面积(BET), 透射电镜(TEM), 扫描电镜(SEM), 拉曼光谱, 紫外-可见(UV-Vis)吸收光谱和荧光光谱(PL)等测试手段对复合材料进行表征. 结果表明: 复合材料中TiO₂为针簇状结构的金红石相, 与石墨烯能够均匀复合; 与纯金红石相TiO₂相比, 复合材料具有较大的比表面积. 研究了该复合材料在紫外光下对罗丹明B 以及可见光下对甲基橙光降解效果. 当氧化石墨烯浓度为0.5 mg·mL^-1时, 制备得到的复合材料rGO-TiO₂具有较好的光催化效果.     

Synthesis, characterization, and catalytic activity of nitrogen and iron(III) co-doped TiO2

The nitrogen and iron(III) co-doped TiO₂ (N–Fe–TiO₂) samples were synthesized via modified sol–gel method by using alkyl amine as both nitrogen source and pore directing agent. Morphologies and properties of the co-doped TiO₂ samples were investigated by X-ray diffraction, Fourier transform infrared spectroscopy, electron spin resonance spectroscopy, UV–Vis spectroscopy, scanning electron microscopy, and transmission electron microscopy. The results showed anatase phase mixed with rutile structure as well as hydroxyl and amine functional groups. The presence of Fe³⁺ in N–Fe–TiO₂ sample was detected at g value of 2.00. In addition, the prepared samples were photocatalytically active for methyl orange degradation under UV light irradiation, but not under visible light.     

Effects of NH 4 + and Cl− on the preparation of nanocrystalline TiO2 by hydrothermal method

Nanocrystalline TiO₂ powders with different morphologies and grain sizes were successfully synthesized by the hydrothermal method. Different concentrations of hydrochloric acid (HCl), ammonium chloride (NH₄Cl), ammonium sulfate [(NH₄)₂SO₄], and ammonium carbonate [(NH₄)₂CO₃] were used as additives in the hydrothermal process to investigate the effect of the concentration of ammonium (NH ₄ ⁺ ) and chloride ions (Cl^?) on the phase compositions, morphologies, and grain sizes of the prepared TiO₂. The as-synthesized samples were characterized by X-ray diffraction (XRD), transmission electron microscopy, Brunauer–Emmett–Teller analysis, and UV–Vis spectra. XRD results show that the as-synthesized powders are composed of anatase or a mixture of anatase and brookite. The grain size of the synthesized nano-TiO₂ powder ranged from 5.0 to 11.3 nm, and the related BET specific surface area varied from 127.5 to 191.0 m²/g. The photocatalytic activities of the prepared TiO₂ powders were evaluated by degradation of methylene blue (MB) in aqueous solution under UV light irradiation, and the results show that the photocatalytic performance of TiO₂ powders synthesized with additives is improved compared with that of TiO₂ prepared without any additives.     

Effect of Erbium on the Photocatalytic Activity of TiO2/Ag Nanocomposites under Visible Light Irradiation

Erbium co‐doped TiO₂/Ag catalysts are synthesized by using a simple, one‐step solvothermal method and characterized by X‐ray diffraction, field‐emission scanning electron microscopy, transmission electron microscopy, Raman analysis, X‐ray photoelectron spectroscopy, and diffuse reflectance spectroscopy. The catalysts exhibit anatase crystal structures with increased visible light absorption compared with pure TiO₂. Enhanced photocatalytic activity is observed with Er co‐doped TiO₂/Ag nanocomposites for Rhodamine B degradation under visible light irradiation. The photocatalytic activity of 1 % Er co‐doped TiO₂/Ag is much higher than that of TiO₂/Ag, TiO₂/Er, pure TiO₂, and commercial Degussa P25. The kinetics of the degradation process are studied and the pseudo‐first‐order rate constant (k) and half‐life time (t_1/2) of the reaction are calculated. The enhanced activity might be accredited to the efficient separation of electron–hole pairs by silver and higher visible light absorption of TiO₂ induced by Er.     

Sonochemical fabrication of fluorinated mesoporous titanium dioxide microspheres

A sonochemical-hydrothermal method for preparing fluorinated mesoporous TiO₂ microspheres was developed. Formation of mesoporous TiO₂ and doping of fluorine was achieved by sonication and then hydrothermal treatment of a solution containing titanium isopropoxide, template, and sodium fluoride. The as-synthesized TiO₂ microspheres were characterized by X-ray diffraction (XRD), Fourier translation infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy-dispersive X-ray (EDX) spectroscopy, photoluminescence spectroscopy (PL), and BET surface areas. The P123 template was removed completely during the hydrothermal and washing steps, which was different from the conventional calcination treatment. The as- synthesized TiO₂ microspheres had good crystallinity and high stability. Results from the photocatalytic degradation of methylene blue (MB) showed that fluorination could remarkably improve the photocatalytic activity of titanium dioxide.     

Preparation and Characterization of Room-temperature Ferromagnetic Ni-doped TiO2 Nanobelts

Ni-doped anatase TiO₂ nanobelts (NBs) with different Ni²⁺ contents were simply prepared by combining ion-exchange with hydrothermal treatment. They were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FTIR), and magnetic measurement techniques. The results showed that Ni²⁺ cations doped into the TiO₂ lattice and no metallic nickel clusters or nanoparticles could be found. The magnetic results demonstrated that the prepared Ni-doped TiO₂ samples had complex magnetic mechanism including room-temperature ferromagnetic and paramagnetic behaviors, and with the increase of Ni²⁺ content, the magnetization also increased under the same applied field owing to uniform distribution of Ni²⁺ ions in TiO₂ nanobelts.     

Hydrothermal synthesis and photocatalytic property of porous CuO hollow microspheres via PS latex as templates

Porous copper oxide (CuO) hollow microspheres have been fabricated through a simple hydrothermal method using PS latex as templates. The as-obtained samples were characterized by means of scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffractometry (XRD) and Fourier transform infrared spectroscopy (FTIR). The influences of the mole ratio of Ethylenediamine (C₂H₈N₂) and copper acetate (Cu(Ac)₂·H₂O), hydrothermal temperature and time on the size and morphologies of the final products have been investigated. The possible formation mechanism of porous CuO hollow microspheres has been proposed and the specific surface area of the hollow microspheres with 81.71 m²/g is measured by BET method. The band gap value calculated from a UV–vis absorption spectrum of porous CuO hollow microspheres is 2.71 eV. The as-synthesized product exhibits high photocatalytic activity during the photodegradation of an organic dyestuff, rhodamine B (RhB), under UV-light illumination.     

Synthesis of anatase TiO2 in a vinyl-containing ionic liquid and its enhanced photocatalytic activity

TiO₂ microspheres were synthesized by the sol–gel method using the ionic liquid (IL) 1-vinyl-3-propylimidazolium iodide (VPIM⁺I^?) as a reaction medium, then calcined at 500 °C. The samples were characterized by X-ray diffraction, scanning electron microscopy, and ultraviolet–visible (UV–Vis) diffuse reflectance spectroscopy. The phase of TiO₂ microspheres is anatase, and VPIM⁺I^? is able to favor the growth of anatase phase and prevents the collapse of small pores. The photocatalytic activity of TiO₂-IL was tested by degradation of 2-nitrophenol under UV light illumination. The photocatalytic activity of TiO₂-IL was higher than that of samples prepared in the reaction medium without VPIM⁺I^?.