Eu-doped B2O3–ZnO–PbO glass phosphor powders with?spherical shape and fine size prepared by spray pyrolysis

Eu-doped B₂O₃–ZnO–PbO glass phosphor powders with spherical shape and fine size were directly prepared by spray pyrolysis. The glass phosphor powders prepared at a temperature of 1100°C had broad XRD peak at around 28°. One glass phosphor powder was formed from one droplet at the preparation temperature range from 900 to 1100°C. The mean size of the glass phosphor powders was 0.75 μm. The glass transition temperature (T _g ) of the glass phosphor powders prepared by spray pyrolysis was 378.5°C. The excitation spectrum of the glass phosphor powders prepared at the optimum preparation temperature of 1100°C had bands at 362, 381, 392, 463, 525, and 532 nm. The glass phosphor powders had emission spectra with bands at 579, 614, and 653 nm. The glass phosphor powders with doping concentration of Eu of 7 wt% had the maximum photoluminescence intensity. The glass phosphor layer formed from the glass phosphor powders had high transparencies above 90%.     

Transparencies of dielectric layers formed from size-controlled Bi-based glass powders obtained by spray pyrolysis

Submicron-size Bi-based glass powders were directly prepared by high-temperature spray pyrolysis. The mean sizes of the Bi-based glass powders were changed from 0.48 to 0.91 μm by changing the concentrations of spray solution. The dielectric layers formed from the Bi-based glass powders with fine size had higher transparencies than those of the dielectric layers formed from the Bi-based glass powders with large size. The transparencies of the dielectric layers formed from the glass powders obtained by spray pyrolysis from spray solution of 0.05 M decreased from 94 to 67% when the firing temperatures of the dielectric layers were changed from 580 to 500 °C. At the same firing temperatures, the transparencies of the dielectric layers formed from the glass powders obtained by spray pyrolysis from spray solution of 0.5 M decreased from 83 to 28%. The dielectric layers formed from the glass powders with fine size had dense and homogeneous structures even at low firing temperatures. PACS 42.70.Ce; 85.60.Pg; 71.55.Jv     

Nanocrystalline CaCu<Subscript>3</Subscript>Ti<Subscript>4</Subscript>O<Subscript>12</Subscript> powders prepared by egg white solution route: synthesis,characterization and its giant dielectric properties

Nanocrystalline CaCu₃Ti₄O₁₂ powders with particle sizes of 50–90 nm were synthesized by a simple method using Ca(NO₃)₂·4H₂O, Cu(NO₃)₂·4H₂O, titanium(diisoproproxide) bis(2,4-pentanedionate) and freshly extracted egg white (ovalbumin) in aqueous medium. The synthesized precursor was characterized by TG-DTA to determine the thermal decomposition and crystallization temperature which was found to be at above 400 °C. The precursor was calcined at 700 and 800 °C in air for 8 h to obtain nanocrystalline powders of CaCu₃Ti₄O₁₂. The calcined CaCu₃Ti₄O₁₂ powders were characterized by XRD, FTIR, SEM and TEM. Sintering of the powders was conducted in air at 1100 °C for 16 h. The XRD results indicated that all sintered samples have a typical perovskite CaCu₃Ti₄O₁₂ structure and a small amount of CuO, although the sintered sample of the 700 °C calcined powders contained some amount of CaTiO₃. SEM micrographs showed the average grain sizes of 12.0±7.8 and 15.5±8.9 μm for the sintered CaCu₃Ti₄O₁₂ ceramics prepared using the CaCu₃Ti₄O₁₂ powders calcined at 700 and 800 °C, respectively. The sintered samples exhibit a giant dielectric constant, ε^′ of ∼ 1.5–5×10⁴. The dielectric behavior of both samples exhibits Debye-like relaxation, and can be explained based on a Maxwell–Wagner model. PACS 77.22.Gm; 81.05.Je; 81.07.Wx; 81.20.Ev     

Dielectric properties of Bi<Subscript>2</Subscript>PbNb<Subscript>2</Subscript>O<Subscript>9</Subscript> ceramics prepared by different techniques

Different techniques for the synthesis of Bi₂PbNb₂O₉, namely the mixed oxide technique, molten salt synthesis, hydrothermal synthesis, co-precipitation and the tartaric acid gel method were investigated and the results on the dielectric properties are reported. The heat-treatment of the precursor powders was the same for all precursor powders. Sintering at 1040 °C under ambient pressure resulted in polycrystalline specimens, while hot-forging at 1040 °C with a pressure of 20 MPa produced c-axis aligned samples. Phase composition and crystallite orientation of the sintered bodies were analyzed by X-ray diffraction. Single-phase material was obtained in all cases. Hot-forging not only yielded c-axis orientation, but also increased the relative densities above 99.4%. The relative permittivity decreased for c-axis oriented material compared to polycrystalline ceramics. Values for the relative permittivity for the hot-forged specimens at 100 °C at 100 kHz varied between 165 and 250, depending on the fabrication method. The Curie temperature for the c-axis aligned samples was 568 °C, independent of the nature of the precursor powders. PACS 77.22.-d; 77.84.-s     

Structural and electrical properties of 0.7Pb(Mg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>)O<Subscript>3</Subscript>–0.3PbTiO<Subscript>3</Subscript> thin films grown on Ir/MgO buffered Si(100) substrates

Thin films of 0.7Pb(Mg_1/3Nb_2/3)O₃–0.3PbTiO₃ (PMN-PT) have been grown on Ir/MgO buffered Si(100) substrates at different substrate temperatures by pulsed laser deposition. Crystalline phases as well as preferred orientations in the PMN-PT films were investigated by X-ray diffraction analysis (XRD). The microstructure, dielectric and ferroelectric properties of PMN-PT film prepared at 650 °C were studied. The results show that the film prepared at 650 °C exhibits pure perovskite phase and single c-axis orientation. The dielectric constant and dissipation factor of the single c-axis oriented film are 1000 and 0.04 at a frequency of 1 kHz, while the remnant polarization and coercive field are about 13.0 μC/cm² and 100 kV/cm under an electric field of 480 kV/cm, respectively. PACS 81.15.Fg; 77.80.-e; 77. 22.Ej; 77.55.+f; 85.50.Gk     

Synthesis and electrochemical performance of spherical LiNi<Subscript>0.8</Subscript>Co<Subscript>0.15</Subscript>Ti<Subscript>0.05</Subscript>O<Subscript>2</Subscript> cathode materials with high tap density

A series of spherical LiNi_0.8Co_0.15Ti_0.05O₂ cathode materials were synthesized through co-oxidation-controlled crystallization method followed by solid-state reaction at different calcination temperatures under oxygen flowing. The crystal structure and particles morphology of the as-prepared powders were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. All samples correspond to the layered α-NaFeO₂ structure with R-3m space group. The LiNi_0.8Co_0.15Ti_0.05O₂ prepared at 800 °C presents a better hexagonal ordering structure and better spherical particles and possesses a high tap density of 3.22 g cm^?3. Meanwhile, the NCT-2 sample exhibits an advanced electrochemical performance with an initial discharge capacity of 174.2 mAh g^?1 and capacity retention of 86.7 % after 30 cycles at 0.2 C.     

Enhanced energy storage in polyvinylidenefluoride (PVDF) + BaZrO<Subscript>3</Subscript> electroactive nanocomposites

PVDF + BaZrO₃ electroactive nanocomposite thin film has been prepared by solution casting method. The structural analysis was carried out by using x-ray diffraction pattern and atomic force microscopy (AFM). Generally, the performance of dielectric capacitors toward higher energy density and higher operating temperatures has been drawing increased interest. In this regard, the present study was focussed on the fabrication and characterization of PVDF + BaZrO₃ electroactive nanocomposites in view of enhancing the energy density at elevated temperature. Cole-Cole plot is an agreement with multiple relaxation process in electroactive nanocomposites. Dielectric energy storage performance is assessed for PVDF nanocomposites with different wt% of BaZrO₃ at different frequencies and temperature. It has been observed that with increase of temperature, the permittivity increased while the energy density slightly decreased but significantly higher than pure polymer PVDF. A high energy density of 6.88 J/cm³ was obtained for BaZrO₃ electroactive nanocomposites at 50 °C and 5.06 J/cm³ at 70 °C. Overall, the testing results indicate that using nanocomposites of PVDF and BaZrO₃ as a dielectric component is promising for implementation to preserve high energy density values up to temperatures of 70 °C.The enhancement of dielectric permittivity and the energy density is attributed due to increase of interracial charge density. The effect of BaZrO₃ nanoparticles in energy density of PVDF is first time reported.     

Light intensity and temperature dependence on performance of a photoelectrochemical cells of ITO/TiO<Subscript>2</Subscript>/PVC-LiClO<Subscript>4</Subscript>/graphite

The photovoltaic characteristics of a photoelectrochemical cell of ITO/TiO₂/PVC-LiClO₄/graphite are reported. This paper is concerned with the influence of light intensity and temperature on short-circuit current density, J_sc and open-circuit voltage, V_oc of the device. The photoelectrochemical cell material was a screen-printed layer of titanium dioxide onto an ITO-covered glass substrate, which was used as a working electrode of the cell. The solid electrolyte was polivinylchloride-lithium perchlorate. The graphite film serves as a counter electrode of the cell. The current density–voltage characteristics of the device under an illumination of 20, 40, 60, 80 and 100 mW cm⁻² light from a tungsten halogen lamp were recorded at 40 °C as well as under an illumination of 100 mW cm⁻² at 30, 35, 40, 45 and 50 °C, respectively. It was found that the short-circuit current density, J_sc of the device increases with both light intensity and temperature. The J_sc obtained at 100 mW cm⁻² was 1.0 μAcm⁻² and that at 50 °C was 0.7 μAcm⁻².     

Effect of alkali metal on the properties of Bi-based glass powders prepared by spray pyrolysis

Bismuth-based glass powders with different quantities of Li₂O were directly prepared by high-temperature spray pyrolysis. The bismuth-based glass powders were completely spherical and submicron in size irrespective of the quantities of the Li₂O additive. The high optical transmittances of the dielectric layers formed from the glass powders obtained by spray pyrolysis were due to the decrease in the glass-transition temperatures of the glass powders with the addition of Li₂O. The ‘yellowing phenomenon’ was not observed in the dielectric layers formed from the glass powders obtained by spray pyrolysis, whereas it occurred in the dielectric layers formed from the glass powders obtained through the conventional melting process. PACS 42.70.Ce; 85.60.Pg; 71.55.Jv     

Structural and electrical properties of KCa<Subscript>2</Subscript>Nb<Subscript>5</Subscript>O<Subscript>15</Subscript> ceramics

A polycrystalline sample of KCa₂Nb₅O₁₅ with tungsten bronze structure was prepared by a mixed oxide method at high temperature. A preliminary structural analysis of the compound showed an orthorhombic crystal structure at room temperature. Surface morphology of the compound shows a uniform grain distribution throughout the surface of the sample. Studies of temperature variation on dielectric response at various frequencies show that the compound has a transition temperature well above the room temperature (i.e., 105°C), which was confirmed by the polarization measurement. Electrical properties of the material have been studied using a complex impedance spectroscopy (CIS) technique in a wide temperature (31–500°C) and frequency (10²–10⁶ Hz) range that showed only bulk contribution and non-Debye type relaxation processes in the material. The activation energy of the compound (calculated from both the loss and modulus spectrum) is same, and hence the relaxation process may be attributed to the same type of charge carriers. A possible ‘hopping’ mechanism for electrical transport processes in the system is evident from the modulus analysis. A plot of dc conductivity (bulk) with temperature variation demonstrates that the compound exhibits Arrhenius type of electrical conductivity.      

Synthesis,structural and electrical properties of double perovskite Sr<Subscript>2</Subscript>NiMoO<Subscript>6</Subscript> ceramics

The double perovskite Sr₂NiMoO₆ powders and ceramics were prepared by two different (conventional and precursor) solid-state reaction methods. The phase structure was characterized by XRD and TEM techniques. It has been indicated that single-phase perovskite powders were obtained when calcined in air at 1300°C. However, nano-particles of the size 30–60 nm have been found in powders prepared with the precursor method, while those from the conventional route exhibit large irregular shaped particles with aggregation. The dielectric properties (ε _r and tanδ) were also examined in the sintered ceramics. The results showed the transition point at 280°C for conventional route, while no clear phase change was observed in ceramics from the precursor route. These observations clearly indicate that the different starting processes affected the phase formation behavior and the electrical properties of Sr₂NiMoO₆ ceramics.     

Effect of calcination conditions on lithium conductivity in Li<Subscript>1.3</Subscript>Ti<Subscript>1.7</Subscript>Al<Subscript>0.3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript> prepared by sol-gel route

In order to study the influence of powder calcination temperature on lithium ion conductivity, synthesized Li_1.3Ti_1.7Al_0.3(PO₄)₃ (LATP) was calcined at temperatures between 750 and 900 °C. The shape and size of the particles were characterized employing scanning electron microscopy (SEM), and specific surface area of the obtained powder was measured. The crystallinity grade of different heat-treated powders was calculated from XRD spectra. Posteriorly, all powders were sintered at 1100 °C employing field-assisted sintering (SPS), and the electrical properties were correlated to the calcination conditions. The highest ionic conductivity was observed for samples made out of powders calcined at 900 °C.     

Preparation and characteristics of?a?BaO–Al2O3–B2O3–SiO2–La2O3 glass ceramic via spray pyrolysis

The characteristics of a BaO–Al₂O₃–B₂O₃–SiO₂–La₂O₃ glass ceramic prepared by spray pyrolysis were studied. Glass powders with spherical shape and amorphous phase were prepared by complete melting at a preparation temperature of 1 500°C. The mean size and geometric standard deviation of the powders prepared at the temperature of 1 500°C were 0.6 μm and 1.3. The glass powders had similar composition to that of the spray solution. The glass transition temperature (T _g) of the glass powders was 600.3°C. Two crystallization exothermic peaks were observed at 769.3 and 837.8°C. Densification of the specimen started at a sintering temperature of 600°C, in which Ba₄La₆O(SiO₄)₆ as main crystal structure was observed. Complete densification of the specimen occurred at a sintering temperature of 800°C. The specimens sintered at temperatures above 800°C had main crystal structure of BaAl₂Si₂O₈.     

CeO<Subscript>2</Subscript> and Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> modified Ni-YSZ anode for solid oxide fuel cell

Ni sintering at high temperature (～ 800 °C) operation drastically degrades the performance of Ni-yttria-stabilized zirconia (YSZ) anode in solid oxide fuel cell (SOFC). Mixed ionic and electronic conductive oxides such as CeO₂ and Nb₂O₅ enhance the dispersion of Ni, CeO₂ enhances the redox behavior and promotes charge transfer reactions, and Nb₂O₅ increases the triple phase boundary. In the present work, anode-supported SOFC is fabricated and tested in H₂ fuel at 800 °C. YSZ and lanthanum strontium manganite (LSM)-YSZ are used as the electrolyte and composite cathode with NiO-YSZ, CeO₂-NiO-YSZ, and Nb₂O₅-NiO-YSZ as an anode. The peak power density obtained for the cell with 10% CeO₂–30% NiO-YSZ anode at the 5 and 25 h of operation is 330 and 290 mW cm^?2 which is higher than that for 40% NiO-YSZ anode (275 mW cm^?2 at 5 h). The peak power density obtained for the cell with 10% Nb₂O₅–30% NiO-YSZ anode at the 5 and 25 h of operation is 301 and 285 mW cm^?2 which is higher than that for 40% NiO-YSZ anode (275 mW cm^?2 at 5 h). Physical characterization has been carried to study morphology, elemental analysis, particle size, and phase formation of the fabricated anode before and after cell operation to correlate the cell performance.     

Genesis,structural, and transport properties of La<Subscript>2</Subscript>Mo<Subscript>2-x</Subscript>W<Subscript>x</Subscript>O<Subscript>9</Subscript> prepared via mechanochemical activation

Fast oxide-ion conductors La₂Mo_2-xW_xO₉ (x = 0–1) have been prepared using mechanochemical activation (MA) of starting oxides in a high-power planetary ball mill. Studies of La₂Mo_2-xW_xO₉ genesis and structural properties using thermal analysis, XRD, SEM, IR, and Raman spectroscopy have revealed that MA results in the formation of an amorphous precursor, while the cubic β-phase is formed after calcination at 700–900 °C. Due to a high dispersion of powders, high-density pellets of W-LAMOX ceramics have been obtained already after sintering at 950 °C. Their electrical conductivity measured by the impedance spectroscopy depends on the W concentration being sufficiently high (up to 5.6?10^?3 S/cm at 630 °C) at temperatures below 650 °C.     

Optimized second-order optical nonlinearity in thermally poled GeS<Subscript>2</Subscript>-Ga<Subscript>2</Subscript>S<Subscript>3</Subscript>-KI chalcohalide glass

0.56GeS₂-0.24Ga₂S₃-0.2KI (mol%) chalcohalide glass was prepared and second-harmonic generation was observed by the thermal poling process. Second-order optical nonlinearity in the glass was also investigated by different poling temperature, voltage and time to optimize the poling parameters to improve χ ⁽²⁾. The maximum χ ⁽²⁾ in our study as large as 3.74 pm/V was obtained under the optimized poling condition with 5.2 kV, 260°C and 120 minutes.     

Optical properties and mechanisms of current flow in Cu<Subscript>2</Subscript>ZnSnS<Subscript>4</Subscript> films prepared by spray pyrolysis

Thin films Cu₂ZnSnS₄ (up to 0.9 μm thick) with p-type conductivity and band gap E_g = 1.54 eV have been prepared by the spray pyrolysis of 0.1 M aqueous solutions of the salts CuCl₂ · 2H₂O, ZnCl₂ · 2H₂O, SnCl₄ · 5H₂O, and (NH₂)₂CS at a temperature T_S = 290°C. The electrophysical properties of the films have been analyzed using the model for polycrystalline materials with electrically active grain boundaries. The energy and geometric parameters of the grain boundaries have been determined as follows: the height of the barriers is E_b ≈ 0.045–0.048 eV, and the thickness of the depletion region is δ ≈ 3.25 nm. The effective concentrations of charge carriers p₀ = 3.16 × 10¹⁸ cm^–3 and their mobilities in crystallites μ_p = 85 cm²/(V s) have been found using the technique for determining the kinetic parameters from the absorption spectra of thin films at a photon energy hν ≈ E_g. The density of states at grain boundaries N_t = 9.57 × 10¹¹ cm^–2 has been estimated.     

Conductivity and spectroscopic studies of Li<Subscript>2</Subscript>O-V<Subscript>2</Subscript>O<Subscript>5</Subscript>-B<Subscript>2</Subscript>O<Subscript>3</Subscript> glasses

Lithium vanadium-borate glasses with the composition of 0.3Li₂O–(0.7-x)B₂O₃–xV₂O₅ (x?=?0.3, 0.325, 0.35, 0.375, 0.4, 0.425, 0.45, and 0.475) were prepared by melt-quenching method. According to differential scanning calorimetry data, vanadium oxide acts as both glass former and glass modifier, since the thermal stability of glasses decreases with an increase in V₂O₅ concentration. Fourier transform infrared spectroscopy data show that the vibrations of [VO₄] structural units occur at V₂O₅ concentration of 45 mol%. It is established that the concentration of V⁴⁺ ions increases exponentially with the growth of vanadium oxide concentration. Direct and alternative current measurements are carried out to estimate the contribution both electronic and ionic conductivities to the value of total conductivity. It is shown that the electronic conductivity is predominant in the total one. The glass having the composition of 0.3Li₂O-0.275B₂O₃-0.475V₂O₅ shows the highest electrical conductivity that has the value of 7.4?×?10^?5 S cm^?1 at room temperature.     

Elevated electrochemical property of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> originated from nano-sized Mn<Subscript>3</Subscript>O<Subscript>4</Subscript>

By employment of nano-sized pre-prepared Mn₃O₄ as precursor, LiMn₂O₄ particles have been successfully prepared by facile solid state method and sol-gel route, respectively. And the reaction mechanism of the used precursors of Mn₃O₄ is studied. The structure, morphology, and element distribution of the as-synthesized LiMn₂O₄ samples are characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). Compared with LiMn₂O₄ synthesized by facile solid state method (SS-LMO), LiMn₂O₄ synthesized by modified sol-gel route (SG-LMO) possesses higher crystallinity, smaller average particle size (~175 nm), higher lithium chemical diffusion coefficient (1.17 × 10^?11 cm² s^?1), as well as superior electrochemical performance. For example, the cell based on SG-LMO can deliver a capacity of 85.5 mAh g^?1 at a high rate of 5 °C, and manifests 88.3% capacity retention after 100 cycles at 0.5 °C when cycling at 45 °C. The good electrochemical performance of the cell based on SG-LMO is ascribed mainly to its small particle size, high degree of dispersion, and uniform element distribution in bulk material. In addition, the lower polarization potential accelerates Li⁺ ion migration, and the lower atom location confused degree maintains integrity of crystal structure, both of which can effectively improve the rate capability and cyclability of SG-LMO.     

Fabrication and electrochemical performance of La<Subscript>0.5</Subscript>Sr<Subscript>0.5</Subscript>CoO<Subscript>3</Subscript> impregnated porous YSZ cathode

La_0.5Sr_0.5CoO₃-yttria-stabilized zirconia (LSCO-YSZ) composite cathode for solid oxide fuel cell (SOFC) has been fabricated by wet impregnation method. Nitrate precursors of La, Sr, and Co have been impregnated into the pre-sintered porous YSZ matrix, which is converted into LSCO phase after calcination at 850 °C in the presence of glycine as confirmed from X-ray diffraction. LSCO of 5, 7, and 10 wt% impregnated porous YSZ have been electrochemically characterized using 2-probe AC conductivity method. Maximum ionic conductivity of 0.27 S/cm at 800 °C and activation energy of 0.15 eV between 600 and 800 °C have been observed for 10 wt% LSCO-YSZ cathode. Area-specific resistance of 1.01 Ω cm² at 800 °C is estimated for the electrolyte-supported half-cell (10 wt% LSCO-YSZ/YSZ). After testing the LSCO-YSZ cathode matrix, the electrolyte-supported full cell (10 wt% LSCO-YSZ/YSZ/NiO-YSZ) has been tested and produced maximum power density 51.12 mW/cm² (109.38 mA/cm²) at 800 °C. The electrolyte-supported full cell exhibited 6 Ω cm² electrode polarization at 800 °C in H₂, which is in higher side leading to low performance. LSCO-YSZ/YSZ/NiO-YSZ SOFC found to give stable performance up to 2 h and scanning electron microscopy analysis has been carried out before and after cell testing to assess the morphological changes.