Evaluation of liquid-phase microextraction conditions for determination of chlorophenols in environmental samples using gas chromatography-mass spectrometry without derivatization

Determination of trace chlorophenols (CPs) in environmental samples has been evaluated using liquid-phase microextraction (LPME) coupled with gas chromatography-mass spectrometry (GC-MS) without derivatization. The LPME procedure used to extract CPs from water involved 15 microL 1-octanol as acceptor solution in a 5.0 cm polypropylene hollow fiber with an inner diameter of 600 microm and a pore size of 0.2 microm. Under the optimal extraction conditions, enrichment factors from 117 to 220 are obtained. The obtained linear range is 1-100 ng mL(-1) with r(2)=0.9967 for 2,4-dichlorophenol (2,4-DCP); 1-100 ng mL(-1) with r(2)=0.9905 for 2,4,6-trichlorophenol (2,4,6-TCP); 5-500 ng mL(-1) with r(2)=0.9983 for 2,3,4,6-tetrachlorophenol (2,3,4,6-TeCP), and 10-1000 ng mL(-1) with r(2)=0.9929 for pentachlorophenol (PCP). The limits of detection range from 0.08 to 2 ng mL(-1), which is comparable with the reported values (12-120 ng mL(-1)). Recoveries of CPs in various matrices exceed 85% with relative standard deviations of less than 10%, except for PCP in landfill leachate. The applicability of this method was examined to determine CPs in environmental samples by analyzing landfill leachate, ground water and soil. The 2,4-DCP and 2,4,6-TCP detected in the landfill leachate are 6.68 and 2.47 ng mL(-1). The 2,4,6-TCP detected in ground water is 2.08 ng mL(-1). All the studied CPs are detected in contaminated soil. The proposed method is simple, low-cost, less organic solvent used and can potentially be applied to analyze CPs in complex environmental matrices.     

Determination of environmental caused chlorophenol levels in urine of the general population

Summary A sensitive, specific and analytically reliable method for the determination of mono-, di-, tri- and tetrachlorophenols in human urine has been elaborated. After acid hydrolysis and a simultaneous steam distillation of the urine samples, spiked with an internal standard, the chromatographically concentrated chlorophenols have been derivatized with pentafluorobenzoylchloride and analyzed by capillary gas chromatography/mass spectrometry. The detection limits for the chlorophenols ranged from 0.2 to 2.5 g/l. Using this method we were able to detect 4-MCP, 2,4-+2,5-DCP, 2,4,6-TCP, 2,4,5-TCP and 2,3,4,6-+2,3,5,6-TeCP in urine samples of a group of 258 men and women which had no known occupational contact to hazardous chemical substances. The 95 percentiles for the concentrations of these substances in the urine samples under investigation were 7.5 (4-MCP); 33.6(2,4-+2,5-DCP); 4,7 (2,4,6-TCP); 4,5 (2,4,5-TCP) and 22.2 (2,3,4,6-+2,3,5,6-TeCP) g per liter. That means, that these chlorophenols are constituents of urine of the normal population in concentrations which in part are greater than that of pentachlorophenol (PCP).     

Optimization of headspace experimental factors to determine chlorophenols in water by means of headspace solid-phase microextraction and gas chromatography coupled with mass spectrometry and parallel factor analysis

In this work an analytical procedure based on headspace solid-phase microextraction and gas chromatography coupled with mass spectrometry (HS-SPME–GC/MS) is proposed to determine chlorophenols with prior derivatization step to improve analyte volatility and therefore the decision limit (CCα). After optimization, the analytical procedure was applied to analyze river water samples. The following analytes are studied: 2,4-dichlorophenol (2,4-DCP), 2,4,6-trichlorophenol (2,4,6-TrCP), 2,3,4,6-tetrachlorophenol (2,4,6-TeCP) and pentachlorophenol (PCP). A D-optimal design is used to study the parameters affecting the HS-SPME process and the derivatization step. Four experimental factors at two levels and one factor at three levels were considered: (i) equilibrium/extraction temperature, (ii) extraction time, (iii) sample volume, (iv) agitation time and (v) equilibrium time. In addition two interactions between four of them were considered. The D-optimal design enables the reduction of the number of experiments from 48 to 18 while maintaining enough precision in the estimation of the effects. As every analysis took 1 h, the design is blocked in 2 days.     

Determination of chlorophenols in landfill leachate using headspace sampling with ionic liquid-coated solid-phase microextraction fibers combined with gas chromatography–mass spectrometry

A new microextraction technique based on ionic liquid solid-phase microextraction (IL-SPME) was developed for determination of trace chlorophenols (CPs) in landfill leachate. The synthesized ionic liquid, 1-butyl-3-methylimidazolium hexafluorophosphate ([C₄MIM][PF₆]), was coated onto the spent fiber of SPME for extraction of trace CPs. After extraction, the absorbed analytes were desorbed and quantified using gas chromatography–mass spectrometry (GC/MS). The term of the proposed method is as ionic liquid-coated of solid-phase microextraction combined with gas chromatography–mass spectrometry (IL-SPME-GC/MS). No carryover effect was found, and every laboratory-made ionic liquids-coated-fiber could be used for extraction at least eighty times without degradation of efficiency. The chlorophenols studied were 2,4-dichlorophenol (2,4-DP), 2,4,6-trichlorophenol (2,4,6-TCP), 2,3,4,6-tetrachlorophenol (2,3,4,6-TeCP), and pentachlorophenol (PCP). The best results of chlorophenols analysis were obtained with landfill leachate at pH 2, headspace extraction for 4 min, and thermal desorption with the gas chromatograph injector at 240 °C for 4 min. Linearity was observed from 0.1 to 1000 μg L⁻¹ with relative standard deviations (RSD) less than 7% and recoveries were over 87%. The limit of detection (LOD) for pentachlorophenol was 0.008 μg L⁻¹. The proposed method was tested by analyzing landfill leachate from a sewage farm. The concentrations of chlorophenols were detected to range from 1.1 to 1.4 μg L⁻¹. The results demonstrate that the IL-SPME-GC/MS method is highly effective in analyzing trace chlorophenols in landfill leachate.     

顶空固相微萃取气相色谱法测定浓海水中的氯酚

建立浓海水中氯酚的顶空固相微萃取气相色谱法检测方法。采用顶空固相微萃取对海水淡化排放的浓海水样品中2,4,6-三氯酚(2,4,6-TCP)和五氯酚(PCP)进行分离富集,气相色谱-电子捕获检测器(μECD)测定浓海水样品中2,4,6-TCP和PCP的含量。讨论了萃取时间、萃取温度、水样盐度等实验条件对富集效率的影响,确定了萃取时间为40 min,萃取温度为60℃。2,4,6-TCP,PCP的质量浓度在0.500~20.0μg/L范围内与其色谱峰面积呈良好的线性关系,线性相关系数均大于0.999,2,4,6-TCP和PCP的检出限(2S/N)分别为0.055,0.128μg/L,测定结果的相对标准偏差为3.65%~11.4%(n=6),加标回收率为73.5%~119.0%。该方法快速,灵敏度高,适合于浓海水中氯酚的分析。     

Determination of chlorophenols in soil samples by microwave-assisted extraction coupled to headspace solid-phase microextraction and gas chromatography-electron-capture detection

Microwave-assisted extraction coupled to headspace solid-phase microextraction was studied and applied for one-step in-situ sample preparation prior to analysis of chlorophenols (CPs) in soil samples. The CPs in soil sample were extracted into the aqueous solution and then directly onto the solid-phase microextraction (SPME) fiber in headspace under the aid of microwave irradiation. After being desorbed from SPME fiber in the GC injection port, CPs were analyzed with a GC-electron-capture detection system. Parameters affecting the extraction efficiency such as the extraction solutions, the pH in the slurry, the humic acid content in the soil, the power and the irradiation time of microwave as well as the desorption parameters were investigated. Experimental results indicated that the extraction of a 1.0 g soil sample with a 6-ml aqueous solution (pH 2) and a polyacrylate fiber under the medium-power irradiation (132 W) for 9 min achieved the best extraction efficiency of about 90% recovery and less than 10% RSD. Desorption was optimal at 300 degrees C for 3 min. Detection limits were obtained at around 0.1-2.0 microg/kg levels. The proposed method provided a simple, fast, and organic solvent-free procedure to analyze CPs from soil sample matrix.     

Comparative studies on the oxidative dechlorination of chlorophenols by a superoxide complex

Transition Metal Chemistry - The chlorophenols (CPs), 4-chlorophenol (4-CP), 2,4-dichlorophenol (2,4-DCP) and 2,4,6-trichlorophenol (2,4,6-TCP), are potent environmental hazards. They can be...     

Sorption behaviour of some chlorophenols in lake aquatic humic matter

The sorption behaviour of 2,4-dichlorophenol (2,4-DCP), 2,4,6-trichlorophenol (2,4,6-TCP), 2,3,4,5-tetrachlorophenol (2,3,4,5-TeCP) and pentachlorophenol (PCP) with an aquatic humic sorbent (HS) was examined in their single and mixed solutions at different acidities (pH 3, 5.5 and 7). The binding capacities and equilibrium coefficients (K(OC)) obtained were fairly close to the literature values but still underline HS's structural and steric influence on the sorption. The most acidic carboxylic (COOH) groups of the HS structure have unquestionably an essential role in the sorption. The amounts of different chlorophenols bound onto the constant quantity of the aquatic HS were in reality very low demonstrating that the amount of the dissolved organic carbon (DOC) in the environment plays a greater role than the value of K(OC). The ability of the aqueous phase to force chlorophenols to associate with the HS becomes at more neutral acidities weaker and weaker and other binding mechanisms become favoured in comparison to hydrogen or hydrophobic bonds. Sorption isotherms were constructed from sorption data, and conformity to a linear model, non-linear Freundlich equation and Langmuir equation was checked.     

Stir bar sorptive extraction with in situ derivatization and thermal desorption-gas chromatography-mass spectrometry for determination of chlorophenols in water and body fluid samples

A new method, stir bar sorptive extraction (SBSE) with in situ derivatization and thermal desorption (TD)-gas chromatography-mass spectrometry (GC-MS), which is used for the determination of trace amounts of chlorophenols, such as 2,4-dichlorophenol (2,4-DCP), 2,4,6-trichlorophenol (2,4,6-TrCP), 2,3,4,6-tetrachlorophenol (2,3,4,6-TeCP) and pentachlorophenol (PCP), in tap water, river water and human urine samples, is described. The derivatization conditions with acetic acid anhydride and the SBSE conditions such as extraction time are investigated. Then, the stir bar is subjected to TD followed by GC-MS. The detection limits of the chlorophenols in tap water, river water and human urine samples are 1-2, 1-2, and 10-20 pg ml⁻¹ (ppt), respectively. The calibration curves for the chlorophenols are linear and have correlation coefficients higher than 0.99. The average recoveries of the chlorophenols in all the samples are higher than 95% (R.S.D. < 10%) with correction using added surrogate standards, 2,4-dichlorophenol-d₅, 2,4,6-trichlorophenol-¹³C₆, 2,3,4,6-tetrachlorophenol-¹³C₆ and pentachlorophenol-¹³C₆. This simple, accurate, sensitive and selective analytical method may be applicable to the determination of trace amounts of chlorophenols in liquid samples.     

Determination of chlorophenols in urine of children and suggestion of reference values

During the course of a human biomonitoring project (Biebesheim in Hessen, Germany) we elaborated a simple but sensitive method for the determination of tri- (TCP), tetra- (TeCP) and pentachlorophenol (PCP) in human urine. Urine samples, spiked with internal standards, were treated by acid hydrolysis. After a steam bath distillation the distillates were extracted using solid phase extraction. Derivatization of the chlorophenols was not carried out. GC/ECD system was used for detection. Detection limits of the chlorophenols were found in the range of 0.02 μg/L urine (detection limits of the ECD: 0.52 to 2.76 μg/L). By this method mono- and dichlorophenols cannot be detected. We investigated 24h-urine samples of 339 pupils (age 10 to 12 years). The children live either in the surroundings of a hazardous waste incinerator (SVA) in Biebesheim (n = 193), or controls (i.e. regions without waste incinerator) in the non polluted areas of Odenwald (n = 90) and Rheintal (n = 56). Between these three groups we did not find statistically significant differences in chlorophenol concentrations of the urine samples. The 95-percentiles of the analyzed samples are 0.74 μg/L (2,3,4-TCP), 1.24 μg/L (2,3,5-TCP), 0.70 μg/L (2,3,6–TCP), 1.10 μg/L (2,4,5–TCP), 1.74 μg/L (2,4,6–TCP), 2.84 μg/L (3,4,5–TCP), 4.78 μg/L (2,3,4,5-TeCP), 1.86 μg/L (2,3,4,6-TeCP), 2.90 μg/L (2,3,5,6-TeCP) and 4.39 μg/L (PCP). Received: 24 February 1999 / Revised: 3 May 1999 / Accepted: 6 May 1999     

Purge-assisted headspace solid-phase microextraction combined with gas chromatography-mass spectrometry for determination of chlorophenols in aqueous samples

A simple, economical and very effective method is demonstrated for simultaneous determination of 2,4-dichlorophenol, 2,4,6-trichlorophenol, 2,3,4,6-tetrachlorophenol and pentachlorophenol, in aqueous samples, by using purge-assisted headspace solid-phase microextraction (PA/HS-SPME) coupled to gas chromatography-mass spectrometry (GC-MS). In the new method, purging the sample enhances the removal of the trace chlorophenols without derivatization from the matrices to the headspace. Extraction parameters including extraction temperature, purge gas flow rate and extraction time were systematically investigated. Under optimal conditions, the relative standard deviations (RSDs) were 4-11% at 50 pg/mL and 5-14% at 5 pg/mL, respectively. The recoveries were in the range of 83-114%. Detection limits were determined at the fg level. These results indicate that PA/HS-SPME provides a significant contribution to highly efficient extraction of semi-volatile CPs, especially for pentachlorophenol, which has the smallest Henry's constant and large octanol-water partitioning coefficient. In addition, the proposed method was successfully applied to the analysis of chlorophenols in landfill leachate. New perspectives are opened for headspace extraction of relatively low vapor pressure compounds in complex matrices.     

Determination of chlorophenols in urine of children and suggestion of reference values

During the course of a human biomonitoring project (Biebesheim in Hessen, Germany) we elaborated a simple but sensitive method for the determination of tri- (TCP), tetra- (TeCP) and pentachlorophenol (PCP) in human urine. Urine samples, spiked with internal standards, were treated by acid hydrolysis. After a steam bath distillation the distillates were extracted using solid phase extraction. Derivatization of the chlorophenols was not carried out. GC/ECD system was used for detection. Detection limits of the chlorophenols were found in the range of 0.02 μg/L urine (detection limits of the ECD: 0.52 to 2.76 μg/L). By this method mono- and dichlorophenols cannot be detected. We investigated 24h-urine samples of 339 pupils (age 10 to 12 years). The children live either in the surroundings of a hazardous waste incinerator (SVA) in Biebesheim (n = 193), or controls (i.e. regions without waste incinerator) in the non polluted areas of Odenwald (n = 90) and Rheintal (n = 56). Between these three groups we did not find statistically significant differences in chlorophenol concentrations of the urine samples. The 95-percentiles of the analyzed samples are 0.74 μg/L (2,3,4-TCP), 1.24 μg/L (2,3,5-TCP), 0.70 μg/L (2,3,6–TCP), 1.10 μg/L (2,4,5–TCP), 1.74 μg/L (2,4,6–TCP), 2.84 μg/L (3,4,5–TCP), 4.78 μg/L (2,3,4,5-TeCP), 1.86 μg/L (2,3,4,6-TeCP), 2.90 μg/L (2,3,5,6-TeCP) and 4.39 μg/L (PCP). Received: 24 February 1999 / Revised: 3 May 1999 / Accepted: 6 May 1999     

One-step extraction and derivatization liquid-phase microextraction for the determination of chlorophenols by gas chromatography–mass spectrometry

A sample pretreatment method for the determination of 18 chlorophenols (CPs) in aqueous samples by derivatization liquid-phase microextraction (LPME) was investigated using gas chromatography–mass spectrometry. Derivatization reagent was spiked into the extraction solvent to combine derivatization and extraction into one step. High sensitivity of 18 CPs derivatives could be achieved after optimization of several parameters such as extraction solvent, percentage of derivatization reagent, extraction time, pH, and ionic strength. The results from the optimal method showed that calibration ranging from 0.5 to 500 μg L⁻¹ could be achieved with the RSDs between 1.75% and 9.39%, and the limits of detection (LOD) are ranging from 0.01 to 0.12 μg L⁻¹ for the CPs. Moreover, the proposed LPME method was compared with solid-phase microextraction (SPME) coupled with on-fiber derivatization technique. The results suggested that using both methods are quite agreeable. Furthermore, the recoveries of LPME evaluated by spiked environmental samples ranged from 87.9% (3,5-DCP) to 114.7% (2,3,5,6-TeCP), and environmental water samples collected from the Pearl River were analyzed with the optimized LPME method, the concentrations of 18 CPs ranged from 0.0237 μg L⁻¹ (3,5-DCP) to 0.3623 μg L⁻¹ (2,3,6-TCP).     

聚邻氨基苯硫酚/纳米金复合膜分子印迹传感器测定2, 4-二氯苯酚

在2,4-二氯苯酚(2,4-DCP)存在下, 在金电极表面自组装邻氨基苯硫酚(oATP)并电聚合oATP/金纳米粒子, 制得2,4-DCP印迹复合膜电化学传感器.采用循环伏安法和交流阻抗技术对传感器制备过程进行了表征, 以K₃Fe(CN)₆为探针, 间接对2,4-DCP进行定量分析.结果表明, 2,4-DCP在5.0×10^-8~1.2×10^-4 mol/L 浓度范围内与K₃Fe(CN)₆示差脉冲伏安曲线的峰电流呈线性关系(R²=0.9964), 检出限为1.5×10^-8 mol/L(S/N=3).该印迹传感器可在几种氯代酚干扰下选择性测定2,4-DCP.利用该传感器对环境水样进行加标回收检测, 回收率为95.2%~109.3%.     

Dechlorination of chlorophenols by magnesium-silver bimetallic system

More than 85% of 10 mg L(-1) of pentachlorophenol (PCP) was removed by magnesium/silver (206/1.47 mM) bimetal system in the presence of acetic acid. Dechlorination was found to be sequential and phenol was identified as the ultimate hydrocarbon skeleton along with some accumulation of tetra-, tri-, and dichlorophenols. The dechlorination reaction was found to follow second-order kinetics. Lower PCP removal efficiency (35%) was observed when the reaction was carried out in the absence of acid using Mg(0)/Ag system. When the reaction was conducted using Mg(0) alone in the presence of acid, substantial sorption of PCP occurred with very low efficiency of PCP dechlorination. Dechlorination studies on 10 mg L(-1) initial concentrations of 2,3,4,6-tetrachlorophenol (2,3,4,6-TeCP) and 2,4,5-trichlorophenol (2,4,5-TCP), under identical conditions as to PCP, revealed that dechlorination efficiency and reaction rate constants decrease with decreasing number of chlorine atoms on the target compound. A correlation (R(2)>0.9) between the dechlorination rate constants and E(LUMO) for chlorophenols was obtained.     

Use of disposable GRC electrodes for the detection of phenol and chlorophenols in liquid chromatography.

In this study, a wall-jet flow cell with a GRC (graphite reinforced by carbon) electrode was designed for the amperometric detection of phenol and chlorophenols in liquid chromatography. The voltammetric responses of these analytes at the GRC electrodes are very similar to those at conventional glassy carbon electrodes. As the GRC electrodes were made of the same materials as commercially available mechanical pencil leads, they exhibit the advantages of low cost, simple surface renewability, lower residual current, and good electrode-to-electrode reproducibility, and thus can be used as disposable-type electrodes. Chromatographic separations of phenol, o-chlorophenol (o-CP), 2,4-dichlorophenol (2,4-DCP), 2,4,6-trichlorophenol (2,4,6-TCP), and pentachlorophenol (PCP) were achieved with an ODS column using a mobile phase containing a mixture of CH3CN and H20 (40:60) containing 25 mM L-(+)tartaric acid (pH = 4.5). Amperometric detections were based on the electrochemical oxidation of these compounds around +0.9 V vs. Ag/AgCl. Under the optimized conditions, linear calibrations were obtained in a range up to 100 microM for phenol, o-CP, 2,4-DCP, 2,4,6-TCP, and 200 microM for PCP, with the correlation coefficients r2 of 0.9992, 0.9997, 0.9986, 0.9992, and 0.9968, respectively. The chromatographic detection limits for the tested analytes were obtained at pmol levels.     

A sensitive electrochemical chlorophenols sensor based on nanocomposite of ZnSe quantum dots and cetyltrimethylammonium bromide

In this work, a very sensitive and simple electrochemical sensor for chlorophenols (CPs) based on a nanocomposite of cetyltrimethylammonium bromide (CTAB) and ZnSe quantum dots (ZnSe–CTAB) through electrostatic self-assembly technology was built for the first time. The composite of ZnSe–CTAB introduced a favorable access for the electron transfer and gave superior electrocatalytic activity for the oxidation of CPs than ZnSe QDs and CTAB alone. Differential pulse voltammetry (DPV) was used for the quantitative determination of the CPs including 2-chlorophenol (2-CP), 2,4-dichlorophenol (2,4-DCP) and pentachlorophenol (PCP). Under the optimum conditions, the peak currents of the CPs were proportional to their concentrations in the range from 0.02 to 10.0 μM for 2-CP, 0.006 to 9.0 μM for 2,4-DCP, and 0.06 to 8.0 for PCP. The detection limits were 0.008 μM for 2-CP, 0.002 μM for 2,4-DCP, and 0.01 μM for PCP, respectively. The method was successfully applied for the determination of CPs in waste water with satisfactory recoveries. This ZnSe–CTAB electrode system provides operational access to design environment-friendly CPs sensors.     

Determination of phenol in landfill leachate by using microchip capillary electrophoresis with end-channel amperometric detection

Phenol, 2,4-dichlorophenol (2,4-DCP), and 2,4,6-trichlorophenol (2,4,6-TCP) were baseline separated by using a homemade microchip CE with an end-channel amperometric detector where a 50 microm Pt microdisk working electrode (WE) and a Pt cathode were integrated onto the microchip itself. Separation parameters such as injection time and voltage, pH of the buffer, online pretreatment condition for WE, reproducibility, and detection potential were investigated. Under the selected separation conditions, the linear ranges for phenol, 2,4-DCP, and 2,4,6-TCP were 2-200, 4-400, and 4-400 microM, respectively. The LODs were 0.4, 0.5, and 0.7 microM for phenol, 2,4-DCP, and 2,4,6-TCP, respectively (S/N = 3). The standard addition method was successfully applied to the analysis of landfill leachate samples and the concentration of phenol in the landfill leachate samples was measured to be 0.32 and 0.21 mM, respectively. The recoveries were in the range of 85-103% and corresponding RSDs were less than 5.5%.     

Mixed hemimicelles solid-phase extraction based on cetyltrimethylammonium bromide-coated nano-magnets Fe3O4 for the determination of chlorophenols in environmental water samples coupled with liquid chromatography/spectrophotometry detection

Mixed hemimicelles solid-phase extraction (SPE) based on cetyltrimethylammonium bromide (CTAB)-coated nano-magnets Fe3O4 was investigated for the preconcentration of four chlorophenols (CPs) in environmental water samples prior to HPLC-spectrophotometry determination in this paper. By the rapid isolating (about 5 min) of Fe3O4 nanoparticles (NPs) through placing a Nd-Fe-B strong magnet on the bottom of beaker, the time-consuming preconcentration process of loading large volume sample in conversional SPE method with a column can be avoided. The unique properties of Fe3O4 NPs such as high surface area and strong magnetism were utilized adequately in the SPE process. This novel separation method produced a high preconcentration rate and factor. A comprehensive study of the adsorption conditions such as the Fe3O4 NPs zeta-potential, CTAB added amounts, pH value, standing time and maximal extraction volume was also presented. Under optimized conditions, four analytes of 2-chlorophenol (2-CP), 2,4-dichlorophenol (2,4-DCP), 2,4,6-trichlorophenol (TCP) and pentachlorophenol (PCP) were quantitatively extracted. The method was then used to determine four CPs in five real environmental water samples. High concentration factors (700) were achieved for each of the analytes, with observed detection limits ranging between 0.11 and 0.15 microg L(-1). The accuracy of method was evaluated by recovery measurements on spiked samples. Good recovery results (83-98%) with satisfactory relative standard deviation (RSD) were achieved. It is important to note that satisfactory preconcentration factors and extraction recoveries for the four CPs were obtained with only a little amount of Fe3O4 NPs (0.1g) and CTAB (60 mg). To the best of our knowledge, this was the first time a mixed hemimicelles SPE method based on Fe3O4 NPs magnetic separation had been used for the pretreatment of environmental water samples.     

Determination of dichlorvos by on-line microwave-assisted extraction coupled to headspace solid-phase microextraction and gas chromatography-electron-capture detection

The pretreatment technique of microwave-assisted extraction on-line headspace solid-phase microextraction (MAE-HS-SPME) was designed and studied for one-step in-situ sample preparation prior to the chromatographic analysis of a pesticide on vegetables. The pesticide on chopped vegetables was extracted into an aqueous solution with the aid of microwave irradiation and then directly onto the SPME fiber in headspace. After being collected on to the SPME fiber and desorbed in the GC injection port, the pesticide (dichlorvos) was analyzed with a GC-electron-capture detection system. The optimum conditions for obtaining extraction efficiency, such as the pH, the polarity modifier, and the salt added in sample solution, the microwave irradiation, as well as the desorption parameters were investigated. Experimental results indicated that the proposed MAE-HS-SPME technique attained the best extraction efficiency of 106% recovery under the optimized conditions, i.e. irradiation of extraction solution (10% aqueous ethylene glycol) at pH 5.0 with medium microwave power for 10 min. Desorption at 220 degrees C for 3 min offered the best detection result. The detection was linear at 5-75 microg/l with correlation coefficient of 0.9985. Detection limit was obtained at approximately 1.0 microg/l level based on S/N=3. The proposed method provided a very simple, fast, and solvent-less procedure to collect pesticides directly from vegetables for GC determination. Its application was illustrated by the analysis of trace dichlorvos in vegetables.