Microwave-assisted solvothermal synthesis and characterization of metastable LiFe(1-x)(VO)(x)PO4 cathodes

Vanadyl ion substituted LiFePO(4) cathodes of the form LiFe(1-x)(VO)(x)PO(4) for 0 ≤ x ≤ 0.25 have been synthesized by a rapid microwave-solvothermal process at <300 °C within 10 min. Clear evidence of vanadyl ion substitution is demonstrated, despite a large size difference between Fe(2+) and (VO)(2+), by characterizing the products structurally, spectroscopically, and electrochemically. The vanadyl ion substitution is accompanied by the formation of iron vacancies in the lattice and Fe(3)O(4) impurity phase, which increases with increasing (VO)(2+) substitution for Fe(2+) and could be removed with a magnetic stir bar. The formation of iron vacancies, along with the oxidation of some Fe(2+) to Fe(3+) to maintain charge neutrality, results in a decrease in the unit cell volume with increasing x despite the substitution of larger (VO)(2+) for Fe(2+). Charge-discharge data of the vanadyl ion substituted samples suggest suppression of the two-phase plateau behavior that is characteristic of LiFePO(4). Electrochemical data collected without any carbon coating reveal that the capacity and rate capability decreases, but the capacity retention improves with (VO)(2+) substitution.     

Tuning the potentials of "extra" electrons in colloidal n-type ZnO nanocrystals via Mg2+ substitution

Colloidal reduced ZnO nanocrystals are potent reductants for one-electron or multielectron redox chemistry, with reduction potentials tunable via the quantum confinement effect. Other methods for tuning the redox potentials of these unusual reagents are desired. Here, we describe synthesis and characterization of a series of colloidal Zn(1-x)Mg(x)O and Zn(0.98-x)Mg(x)Mn(0.02)O nanocrystals in which Mg(2+) substitution is used to tune the nanocrystal reduction potential. The effect of Mg(2+) doping on the band-edge potentials of ZnO was investigated using electronic absorption, photoluminescence, and magnetic circular dichroism spectroscopies. Mg(2+) incorporation widens the ZnO gap by raising the conduction-band potential and lowering the valence-band potential at a ratio of 0.68:0.32. Mg(2+) substitution is far more effective than Zn(2+) removal in raising the conduction-band potential and allows better reductants to be prepared from Zn(1-x)Mg(x)O nanocrystals than can be achieved via quantum confinement of ZnO nanocrystals. The increased conduction-band potentials of Zn(1-x)Mg(x)O nanocrystals compared to ZnO nanocrystals are confirmed by demonstration of spontaneous electron transfer from n-type Zn(1-x)Mg(x)O nanocrystals to smaller (more strongly quantum confined) ZnO nanocrystals.     

Enhanced reducibility of Ce1-xTixO2 compared to that of CeO2 and higher redox catalytic activity of Ce1-x-yTixPtyO2-delta compared to that of Ce1-xPtxO2-delta

Nanocrystalline Ce(1)(-)(x)Ti(x)O(2) (0 < or = x < or = 0.4) and Ce(1-)(x)(-)(y)Ti(x)Pt(y)O(2)(-)(delta) (x = 0.15, y = 0.01, 0.02) solid solutions crystallizing in fluorite structure have been prepared by a single step solution combustion method. Temperature programmed reduction and XPS study of Ce(1)(-)(x)Ti(x)O(2) (x = 0.0-04) show complete reduction of Ti(4+) to Ti(3+) and reduction of approximately 20% Ce(4+) to Ce(3+) state compared to 8% Ce(4+) to Ce(3+) in the case of pure CeO(2) below 675 degrees C. The substitution of Ti ions in CeO(2) enhances the reducibility of CeO(2). Ce(0.84)Ti(0.15)Pt(0.01)O(2)(-)(delta) crystallizes in fluorite structure and Pt is ionically substituted with 2+ and 4+ oxidation states. The H/Pt atomic ratio at 30 degrees C over Ce(0.84)Ti(0.15)Pt(0.01)O(2)(-)(delta) is 5 and that over Ce(0.99)Pt(0.01)O(2)(-)(delta) is 4 against just 0.078 for 8 nm Pt metal particles. Carbon monoxide and hydrocarbon oxidation activity are much higher over Ce(1-)(x)(-)(y)Ti(x)Pt(y)O(2) (x = 0.15, y = 0.01, 0.02) compared to Ce(1)(-)(x)Pt(x)O(2) (x = 0.01, 0.02). Synergistic involvement of Pt(2+)/Pt degrees and Ti(4+)/Ti(3+) redox couples in addition to Ce(4+)/Ce(3+) due to the overlap of Pt(5d), Ti(3d), and Ce(4f) bands near E(F) is shown to be responsible for improved redox property and higher catalytic activity.     

Magnetic and high rate adsorption properties of porous Mn(1-x)Zn(x)Fe2O4 (0 ≤ x ≤ 0.8) adsorbents

Porous spinel ferrites Mn(1-x)Zn(x)Fe(2)O(4) (0 ≤ x ≤ 0.8) are synthesized by a simple sol-gel method with egg white. All samples exhibit porous morphologies and large BET surface area (S(BET)). The substitution of Zn(2+) affects the magnetic properties of ferrites and the adsorption properties of methylene blue (MB) on ferrites, obviously. The saturation magnetization (Ms) of Mn(1-x)Zn(x)Fe(2)O(4) increases before x=0.4, and decreases with further increase of Zn(2+) substitution. This can be ascribed to the changes of the cationic distribution and the variation of spin arrangement in A-site and B-site of spinel structure. All samples show high adsorption capacity and the removal efficiencies of MB reach up to >90% within 3 h. The Zn(2+) substitution accelerates the adsorption rate and capacity of MB on Mn(1-x)Zn(x)Fe(2)O(4). The quickest adsorption occurred at x=0.2 and the largest adsorption capacity occurred at x=0.8.     

Alloyed (ZnS)(x)(Cu2SnS3)(1-x) and (CuInS2)(x)(Cu2SnS3)(1-x) nanocrystals with arbitrary composition and broad tunable band gaps

Cu(2)SnS(3) nanocrystals with metastable zincblende and wurtzite structures have been successfully synthesized for the first time. Alloyed (ZnS)(x)(Cu(2)SnS(3))(1-x) and (CuInS(2))(x)(Cu(2)SnS(3))(1-x) nanocrystals with arbitrary composition (0 ≤x≤ 1) and ultra-broad tunable band gaps (3.63 to 0.94 eV) were obtained.     

Compositionally tunable Cu2ZnSn(S(1-x)Se(x))4 nanocrystals: probing the effect of Se-inclusion in mixed chalcogenide thin films

Nanocrystals of multicomponent chalcogenides, such as Cu(2)ZnSnS(4) (CZTS), are potential building blocks for low-cost thin-film photovoltaics (PVs). CZTS PV devices with modest efficiencies have been realized through postdeposition annealing at high temperatures in Se vapor. However, little is known about the precise role of Se in the CZTS system. We report the direct solution-phase synthesis and characterization of Cu(2)ZnSn(S(1-x)Se(x))(4) nanocrystals (0 ≤ x ≤ 1) with the aim of probing the role of Se incorporation into CZTS. Our results indicate that increasing the amount of Se increases the lattice parameters, slightly decreases the band gap, and most importantly increases the electrical conductivity of the nanocrystals without a need for annealing.     

Growth kinetic on the optical properties of the Pb(1-x)Mn(x)Se nanocrystals embedded in a glass matrix: thermal annealing and Mn2+ concentration

Semimagnetic Pb(1-x)Mn(x)Se nanocrystals were synthesized by a fusion method in a glass matrix and characterized by optical absorption (OA), atomic/magnetic force microscopy (AFM/MFM), and photoluminescence techniques. MFM images strongly indicated the formation of Pb(1-x)Mn(x)Se magnetic phases in the glass system. Quantum dot size was manipulated by tuning annealing time. It was shown that Mn(2+) impurity affects nucleation, where Mn(2+)-doped samples present a redshift of the OA peak after a short annealing time and a blueshift after long annealing time compared to undoped PbSe NCs. This behavior was linked to the dependence of band-gap energy and the absorption selection rule on Mn(2+) concentration. Photoluminescence in the Pb(1-x)Mn(x)Se nanocrystals increases as the temperature rises up to a point and then decreases at higher temperatures. Anomalous increases in emission efficiency were analyzed by considering temperature induced carrier-transfer in semimagnetic Pb(1-x)Mn(x)Se quantum dots nanocrystals of different sizes.     

Synthesis of Cd-free water-soluble ZnSe(1-x)Te(x) nanocrystals with high luminescence in the blue region

Cd-free core-shell nanocrystals (ZnSe(1-x)Te(x)/ZnS, 0相似文献   

Li(+) ion conductivity in rock salt-structured nickel-doped Li(3)NbO(4)

Two mechanisms of doping Li(3)NbO(4), which has an ordered, rock salt superstructure, have been established. In the "stoichiometric mechanism", the overall cation-to-anion ratio is maintained at 1:1 by means of the substitution 3Li(+) + Nb(5+) --> 4Ni(2+). In the "vacancy mechanism", Li(+) ion vacancies are created by means of the substitution 2Li(+) --> Ni(2+). Solid solution ranges have been determined for both mechanisms and a partial phase diagram constructed for the stoichiometric join. On the vacancy join, the substitution mechanism has been confirmed by powder neutron diffraction; associated with lithium vacancy creation, a dramatic increase in Li(+) ion conductivity occurs with increasing Ni content, reaching a value of 5 x 10(-4) Omega(-1) cm(-1) at 300 degrees C for composition x= 0.1 in the formula Li(3-2x)Ni(x)NbO(4). This is the first example of high Li(+) ion conductivity in complex oxides with rock salt-related structures.     

Sandia octahedral molecular sieves (SOMS): structural and property effects of charge-balancing the M(IV)-substituted (M = Ti, Zr) Niobate framework

Sandia octahedral molecular sieves (SOMS) is an isostructural, variable composition class of ion exchangers with the general formula Na(2)Nb(2-x)M(IV)(x)O (6-x)(OH)(x).H(2)O (M(IV) = Ti, Zr; x = 0.04-0.40) where up to 20% of the framework Nb(V) can be substituted with Ti(IV) or Zr(IV). This class of molecular sieves is easily converted to perovskite through low-temperature heat treatment (500-600 degrees C). This report provides a detailed account of how the charge imbalance of this Nb(V)-M(IV) substitution is compensated. X-ray powder diffraction with Rietveld refinement, infrared spectroscopy, thermogravimetric analysis, (23)Na MAS NMR, and (1)H MAS NMR were used to determine how the framework anionic charge is cation-balanced over a range of framework compositions. All spectroscopic evidence indicated a proton addition for each M(IV) substitution. Evidences for variable proton content included (1) increasing OH observed by (1)H MAS NMR with increasing M(IV) substitution, (2) increased infrared band broadening indicating increased H-bonding with increasing M(IV) substitution, (3) increased TGA weight loss (due to increased OH content) with increasing M(IV) substitution, (4) no variance in population on the sodium sites (indicated by Rietveld refinement) with variable composition, and (5) no change in the (23)Na MAS NMR spectra with variable composition. Also observed by infrared spectroscopy and (23)Na MAS NMR was increased disorder on the Nb(V)/M(IV) framework sites with increasing M(IV) substitution, evidenced by broadening of these spectral features. These spectroscopic studies, along with ion exchange experiments, also revealed the effect of the Nb(V)/M(IV) framework substitution on materials properties. Namely, the temperature of conversion to NaNb(1-x)M(IV)(x)O(3) (M = Ti, Zr) perovskite increased with increasing Ti in the framework and decreased with increasing Zr in the framework. This suggested that Ti stabilizes the SOMS framework and Zr destabilizes the SOMS framework. Finally, comparing ion exchange properties of a SOMS material with minimal (2%) Ti to a SOMS material with maximum (20%) Ti revealed the divalent cation selectivity of these materials which was reported previously is a function of the M(IV) substitution in the framework. A thorough investigation of this class of SOMS materials has revealed the importance of understanding the influence of heterovalent substitutions in microporous frameworks on material properties.     

NMR study of Li+ ion dynamics in the perovskite Li(3x)La(1/3-x)NbO3

(7)Li and (6)Li nuclear magnetic resonance (NMR) experiments are carried out on the perovskite Li(3x)La(1/3-x)NbO(3). The results are compared to those obtained on the titanate Li(3x)La(2/3-x)TiO3 (LLTO) in order to investigate the effect, on the lithium ion dynamics, of the total substitution of Nb(5+) for Ti(4+) in the B-site of the ABO(3) perovskites. The XRD patterns analysis reveals that this substitution leads to a change in the distribution of the La(3+) ions in the structure. La(3+) ions distribution is very important, in regard to ionic conductivity, because these immobile ions can be considered as obstacles for the long-range Li+ motion. If compared to the titanates, the compounds of the niobate solid solution have a bigger unit cell volume, a smaller number of La(3+) ions, and a higher number of vacancies. These should favor the motion of the mobile ions into the structure. This is not experimentally observed. Therefore, the interactions between the mobile species and their environment greatly influence their mobility. (7)Li and (6)Li NMR relaxation time experiments reveal that the Li relaxation mechanism is not dominated by quadrupolar interaction. (7)Li NMR spectra reveal the presence of different Li+ ion sites. Some Li+ ions reside in an isotropic environment with no distortion, some others reside in weakly distorted environments. T(1), T(1)(rho), and T(2) experiments allow us to evidence two motions of Li+. As in LLTO, T(1) probes a fast motion of the Li+ ions inside the A-cage of the perovskite structure and T(1)(rho) a slow motion of these ions from A-cage to A-cage. At variance with what has been observed in LLTO, these different Li+ ions can be differentiated through the spin-lattice relaxation times, T(1) and T(1)(rho), as well as through the transverse relaxation time, T(2).     

Investigation of hydrothermal routes to mixed-metal cerium titanium oxides and metal oxidation state assignment using XANES

The reaction between TiF(3) or TiO(2) and Ce(3+) in sodium hydroxide solutions yields highly crystalline NaCeTi(2)O(6) at room temperature and under mild hydrothermal conditions (T < or = 240 degrees C). There is no evidence for the formation of ternary Ce-Ti-O materials by this method, and the use of bases other than NaOH always produces poorly crystalline materials. The material NaCeTi(2)O(6) has a distorted perovskite structure with sodium and cerium ions randomly occupying the A sites: Pnma, a = 5.4517(8) A, b = 7.7292(6) A, c =5.4573(3) A. XANES spectroscopy at the Ti K edge and Ce L(III) edge, with reference to crystalline model compounds, reveals that cerium is found solely as Ce(III) and titanium as Ti(IV) in NaCeTi(2)O(6). Isomorphous substitution of Ce(3+) by Nd(3+) or Ti(4+) by V(4+) is found to be very facile under hydrothermal conditions (at a temperature of 240 degrees C), by addition of appropriate amounts of metal salts to the hydrothermal reaction mixtures. The series NaCe(1-x)Nd(x)Ti2O6 (0 < or = x < or = 1) and NaCeTi(2-x)V(x)O6 (0 相似文献   

New perovskite materials of the La(2-x)Sr(x)CoTiO6 series

Substitution of La(3+) by Sr(2+) in the double perovskite La(2)CoTiO(6) yields materials of the La(2-x)Sr(x)CoTiO(6) series showing a significant amount of trivalent cobalt ions when prepared at ambient atmosphere. The as-prepared compounds can be reduced in severe conditions retaining the perovskite structure while inducing the formation of a large amount of oxygen vacancies. The limit of aliovalent substitution in this series was found to extend up to x = 1. For substitution of La(3+) up to 15% cobalt and titanium are ordered, though the order is progressively lost as x increases; for x≥ 0.30 no ordering is observed as evidenced by magnetic measurements. The ability of these materials to present either cobalt ions in a mixed oxidation state or large amounts of anion vacancies depending on the atmosphere makes them interesting to be further investigated regarding their electrical and electrochemical properties, and hence, their usefulness in some electrochemical devices.     

Spectroscopic properties of Er(3+)/Yb(3+) co-doped Bi(2)O(3)-B(2)O(3)-GeO(2) glasses

Er(3+)/Yb(3+) co-doped 60Bi(2)O(3)-(40 - x)B(2)O(3)-xGeO(2) (BBG; x=0, 5, 10, 15 mol%) glasses that are suitable for fiber lasers, amplifiers have been fabricated and characterized. The absorption spectra, emission spectra, and lifetime of the (4)I(13/2) level and quantum efficiency of Er(3+):(4)I(13/2) --> (4)I(15/2) transition were measured and calculated. With the substitution of GeO(2) for B(2)O(3), both Delta lambda(eff) and sigma(e) decrease from 75 to 71 nm and 9.88 to 8.12 x 10(-21) cm(2), respectively. The measured lifetime of the (4)I(13/2) level and quantum efficiency of Er(3+):(4)I(13/2) --> (4)I(15/2) transition increase from 1.18 to 1.5 ms and 36.2% to 43.2%, respectively. The emission spectra of Er(3+):(4)I(13/2) --> (4)I(15/2) transition was also analyzed using a peak-fit routine, and an equivalent four-level system was proposed to estimate the stark splitting for the (4)I(15/2) and (4)I(13/2) levels of Er(3+) in the BBG glasses. The results indicate that the (4)I(13/2) --> (4)I(15/2) emission of Er(3+) can be exhibit a considerable broadening due to a significant enhance the peak A, and D emission.     

Vibrational modes and structural characteristics of (Ba(0.3)Sr(0.7))[(Zn(x)Mg(1-x))(1/3)Nb(2/3)]O3 solid solutions

(Ba(0.3)Sr(0.7))[(Zn(x)Mg(1-x))(1/3)Nb(2/3)]O(3) (BSZMN) (x = 0.0, 0.2, 0.4, 0.6, 0.8, 1.0) solid solution ceramics were synthesized by the conventional solid-state sintering technique. Vibration spectra (Raman spectroscopy and Fourier transform far-infrared reflection spectroscopy, short for FTIR) and X-ray diffraction (XRD) were employed to evaluate the correlation between crystal structures and vibration modes of these solid solutions as a function of Mg(2+) ions replaced by Zn(2+) ions. It is verified that these ceramics present a phase transition, i.e., the crystal structure changes from hexagonal phase (P ?3m1, where x≤ 0.4) to the pseudocubic phase (I4/mcm, where x≥ 0.8) with increasing Zn(2+) content. The phase transition is a gradual process, the sample where x = 0.6 is of the transition phase, i.e., at x = 0.6, phase transition begins to appear from hexagonal phase to pseudocubic phase but is not complete. The phase transition is also verified by the FTIR spectra. Tilting of oxygen octahedra is the main reason for the phase transition. The phonon modes of the vibration spectra were assigned, the position and width were determined, and the correlation of phonon vibrations with the microstructure for the different atoms substituted in B'-site was found.     

Density-functional-theory studies of the infrared spectra of titanium carbide nanocrystals

The infrared (IR) spectra of cuboidic titanium carbide (TiC) nanocrystals have been studied at the density-functional-theory (DFT) level using the Becke-Perdew (BP) functional and triple-zeta quality basis sets augmented by one set of polarization functions (TZVP). The accuracy of the calculations was checked by DFT calculations using the Perdew-Burke-Ernzerhof hybrid functional (PBE0) and up to quadruple-zeta quality basis sets augmented by one set of polarization functions (QZVP). The calculated IR spectrum for Ti(14)C(13) (3 x 3 x 3) is found to be in fair agreement with the experimental IR spectrum obtained by infrared resonance-enhanced multiphoton ionization (IR-REMPI) measurements, whereas, for Ti(18)C(18) (4 x 3 x 3) and Ti(32)C(32) (4 x 4 x 4), the calculated IR spectra differ significantly from the experimental ones. The smallest TiC cluster (Ti(4)C(4), 2 x 2 x 2) considered has not been reported in any mass-spectrometer studies. The present DFT calculations show that the vibrational modes related to the in-plane vibrations of solid TiC are not observed in the IR-REMPI spectra of nanocrystals larger than Ti(14)C(13). Contrary to solid TiC, the studied TiC nanocrystals are nonmetallic with optical gaps of 0.62 eV (0.55 eV) and 0.028 eV (0.027 eV) for Ti(32)C(32) and Ti(108)C(108) (6 x 6 x 6), calculated at the time-dependent density-functional-theory (TDDFT) level using the BP functional. The HOMO-LUMO gaps obtained in the BP DFT calculations are given within parentheses. At the PBE0 DFT level, the HOMO-LUMO gaps for Ti(32)C(32) and Ti(108)C(108) are 1.74 and 0.32 eV, respectively.     

Effects of Composition on the Structure and Capacitive Properties of Ti/(ZrO2)x(RuO2)1-x Electrodes

<正>A series of nominal composition Ti/(ZrO_2)_x(RuO_2)_(1-x) (0.1≤x≤0.9) coatings chan- ged in 10% steps was deposited on titanium substrate from RuCl_3·nH_2O and ZrCl_4 containing ethanol solution by thermal decomposition method. The X-ray diffraction (XRD), high-resolution transmission electron microscopy (HR-TEM) and electrochemical tests were performed to clarify the effects of ZrO_2 content on the structure and capacitive property of Ti/(ZrO_2)_x(RuO_2)_(1-x). The results show that by adding ZrO_2 into the coatings the degree of crystallization of RuO_2 decreases. The specific capacitance firstly increases and then deceases with the increase of ZrO_2 content in the mixed oxide coatings. The film of Ti/(ZrO_2)_(0.6)(RuO_2)_(0.4) consisting of amorphous matrix and fine nano-crystalline RuO_2 (about 4 nm) has the maximum specific capacitance of 713.27 F/g(RuO_2).     

Enhanced electronic correlation and thermoelectric response by Cu-doping in Ca(3)Co(4)O(9) single crystals

The structure, anisotropic magnetic, electrical and thermal transport properties for single crystals of Ca(3)Co(4-x)Cu(x)O(9) (x = 0, 0.2, 0.4, 0.6 and 0.8) have been investigated systematically. The Cu-doping with x = 0.2 at Co-site is sufficient to drive the low-temperature spin-glass state in the Ca(3)Co(4)O(9) system. The value of resistivity along ab-plane decreases monotonously with increasing x in the whole temperature range studied, and around room temperature, the in-plane resistivity of Ca(3)Co(3.2)Cu(0.8)O(9) is about 71% smaller than that of the undoped sample. The temperature region where the Fermi-liquid transport mechanism dominates becomes remarkably narrowed due to the Cu-doping while the electronic correlation in the system is enhanced. With further addition of Cu in the Ca(3)Co(4)O(9) system, the in-plane thermopower (S(ab)) increases slowly and the room-temperature S(ab) for Ca(3)Co(3.2)Cu(0.8)O(9) is about 17% larger than that of the undoped sample. As a result, the power factor along the ab-plane is enhanced by about 3.8 times compared to the undoped sample. The results are suggested to originate from the variations of carrier concentration and electronic correlation in this system via the different Cu-doping states: Cu(3+)/Cu(2+) (Cu(3+) major) into the CoO(2) layer for x ≤ 0.4, while Cu(2+)/Cu(3+) (Cu(2+) major) into the Ca(2)CoO(3) layers for x > 0.4.     

Interplay between defect structure and catalytic activity in the Mo(10-x)V(x)O(y) mixed-oxide system

The Mo(10-x)V(x)O(y) solid-solution systems (0≤x≤10) were studied by electron paramagnetic resonance spectroscopy. The results show the existence of paramagnetic vanadyl VO(2+) species, whose concentration becomes maximal for Mo(5)V(5)O(y·). A quantitative analysis of the [VO(2+)] concentration as a function of the Mo/V ratio allows it to characterize the prevailing defect chemistry in the Mo(10-x)V(x)O(y) system. In this respect, the semi-conducting properties of Mo(10-x)V(x)O(y) are p-type in an interval of Mo(9)V(1)O(y)-Mo(5)V(5)O(y) and switch into n-type because of the conduction electrons in a composition range of Mo(5)V(5)O(y)-Mo(1)V(9)O(y). Highest catalytic activity is obtained when vanadium acts as an acceptor center and oxygen vacancies ν(··)(O) are formed for reasons of charge compensation. In addition to the surface, ν(··)(O) and VO(2+) centers in the bulk have to be considered too for heterogeneous catalysis.