基于电中性锇配合物的低背景DNA电化学传感器

采用紫外光谱和电化学方法研究了一种电中性锇配合物Os(DPPZ)(PC)(H₂O)DPPZ=联吡啶并[3,2-a,2',3'-c]吩嗪, PC=2,6-吡啶二羧酸}与DNA的相互作用. 紫外光谱结果表明, DNA的加入引起配合物特征吸收峰的减色及红移效应, 说明二者之间存在嵌插作用. 循环伏安实验结果表明, 配合物溶液中加入DNA后, 氧化还原峰电流降低且式电位正移, 证实了二者之间的嵌插作用模式. 将该配合物作为杂交指示剂对CaMV35S启动子基因片段进行检测发现, 在单链探针DNA修饰电极上未观察到指示剂的电化学信号, 而在杂交后的双链DNA电极上呈现灵敏的电化学响应, 表明传感器具有较高的信噪比. 定量分析实验结果表明, 在最佳条件下, 杂交指示剂在传感器上的还原峰电流与目标序列浓度在8.0×10^-10~2.8×10^-9 mol/L范围内呈良好的线性关系. 选择性实验结果表明, 该传感器对互补序列、碱基错配序列和非互补序列具有良好的识别能力.     

基于金纳米粒子/聚阿魏酸/多壁碳纳米管修饰电极的DNA计时库仑法生物传感器的制备

构建了基于金纳米粒子/聚阿魏酸/多壁碳纳米管(AuNPs/PFA/MWCNTs)修饰电极的DNA计时库仑法生物传感器.利用循环伏安技术在多壁碳管修饰的玻碳电极表面上聚合一层阿魏酸,在恒电位条件下,在阿魏酸表面沉积金纳米粒子,巯基DNA作为探针通过金硫键固定在金纳米粒子表面.电化学交流阻抗技术(EIS)与扫描电镜(SEM...     

苯甲酸二聚铜配合物与DNA相互作用的电化学研究及应用

采用电化学法对自行合成的苯甲酸二聚铜配合物[Cu(R)2]与鲑鱼精DNA的相互作用进行了研究。配合物在0.197 V和0.162 V处有一对氧化还原峰。加入双链DNA(dsDNA)后,氧化还原峰电流明显降低且式量电位正移,说明苯甲酸二聚铜配合物与DNA以嵌入方式生成一种非电活性超分子复合物,导致苯甲酸二聚铜配合物的峰电流降低,峰电流在一定范围内与鲑鱼精dsDNA质量浓度呈线性关系,线性范围为3.0×10-2~4.5×10-3mg/L,检出限为3.5×10-4mg/L。同时,以[Cu(R)2]作杂交指示剂,把一种新型发夹结构锁核酸探针(LNA)固定在金电极表面制备了电化学生物传感器,将该修饰电极与人工合成的慢性粒细胞白血病BCR/ABL融合基因片段进行杂交,用差示伏安法进行检测,该铜配合物能够较好地区分探针序列、单碱基错配序列和互补链序列。     

一种在非水介质中检测有机化合物微量水的电化学传感器

制备了聚二-(1,10-邻菲啰啉)(1,10-邻菲啰啉-5,6-二酮)合钌修饰玻碳电极,研究了在非水介质中与水反应后的电极反应,成功构建了一种检测微量水的电化学传感器,建立了在非水介质中检测有机物中微量水的电化学分析法.在含有0.05 mol/L六氟磷酸四丁基胺的乙腈溶液中,采用差分脉冲伏安法,在电位-0.12 V处测得的阳极峰电流与水含量在0.02％～5.66％范围内成正比,检出限为0.005％(S/N=3).将传感器分别应用于乙腈、丙酮、93号汽油、柴油4种有机物中微量水的测定,相对标准偏差小于3.6％,加标回收率为94.1％ ～ 105.0％,测定结果与卡尔费休法相符.     

槲皮万寿菊素金属配合物的合成、抗氧化活性及与DNA结合的研究

合成了槲皮万寿菊素铜(Ⅱ)、锌(Ⅱ)铁(Ⅲ)三种配合物,采用红外、紫外光谱及元素分析等方法分析了其配位情况,研究了配合物清除DPPH自由基、超氧阴离子自由基和羟基自由基的活性,并运用紫外光谱滴定实验,研究了配体及配合物与ct-DNA的相互作用.结果表明,配合物较配体具有更强的清除DPPH自由基、超氧阴离子自由基和羟基自...     

基于聚硫堇、DNA/纳米银复合物共修饰癌胚抗原免疫传感器的研究

将硫堇聚合到玻碳电极(GCE)表面形成带正电的多孔聚硫堇(PTH)复合膜, 通过静电吸附固定DNA/纳米银复合物, 利用复合物中纳米银大的比表面积和强的吸附能力将癌胚抗体(anti-CEA)固定到电极表面, 从而制得高灵敏的电流型癌胚抗原(CEA)免疫传感器. 通过循环伏安法考察了电极表面的电化学行为, 并对免疫传感器的性能进行了详细研究. 在最优的实验条件下, 用示差脉冲伏安法(DPV)对癌胚抗原进行检测, 其线性范围为1.0～10.0 ng•mL^－1和10.0～80.0 ng•mL^－1, 线性相关系数分别为0.9983和0.9970, 检测限为0.24 ng•mL^－1, 并将该免疫传感器用于血清样品中CEA的检测.     

基于3,5-二溴水杨醛席夫碱镍配合物-氧化石墨烯电化学免疫传感器检测Anti-IgG含量的研究

应用物理吸附法将羊抗人IgG抗原直接固定于3,5-二溴水杨醛席夫碱镍配合物-氧化石墨烯修饰的金电极表面,制备电化学免疫传感器。采用循环伏安法和交流阻抗法对传感器进行表征,结果表明该传感器适合检测Anti-IgG浓度。同时探讨了缓冲液pH值、扫描速度、免疫反应温度、抗原与抗体配比对循环伏安峰电流的影响,结果表明在5~100mV/s扫速范围内,峰电流与扫速呈线性。孵育最优条件为25℃,h-IgG与Anti-IgG配比为1∶1。循环伏安法研究还表明Anti-IgG浓度在0.01~260μg/L范围内,线性关系良好,相关系数r2=0.993,检出限(S/N=3)为0.006μg/L,据此建立了检测Anti-IgG浓度的新方法。     

用石墨烯/聚二烯丙基二甲基氯化铵复合修饰电极为工作电极的循环伏安法同时测定人血清中尼莫地平和硝苯地平的含量

用聚二烯丙基二甲基氯化铵(PDDA)作为一种绿色还原剂还原氧化石墨(GO)制得石墨烯(GR),并进一步制得GR/PDDA复合物。将0.5g·L~(-1) GR/PDDA悬浮液均匀滴涂于经预处理的玻碳电极(GCE)表面,于红外灯下照射烘干,即得GR/PDDA/GCE复合修饰电极。用傅里叶红外光谱仪对所合成的复合物进行表征,证实了合成是成功的。用循环伏安法表征了该修饰电极的电化学特性,证明了GCE表面的GR/PDDA镀层不仅增加了电极的表面积,而且加速了电荷传导速率。在pH 6.0的磷酸氢二钠-柠檬酸缓冲溶液中,研究了尼莫地平(NM)和硝苯地平(NF)在复合修饰电极上的电化学行为,结果表明,两者依次在-0.444,-0.737V处出现较灵敏的还原峰,并且NM和NF的浓度在1.0×10~(-6)～1.4×10~(-4) mol·L~(-1),4.0×10~(-7)～2.6×10~(-4) mol·L~(-1)内分别与其还原峰电流呈线性关系。检出限(3s)分别为3.9×10-7 mol·L~(-1)和5.6×10-8 mol·L~(-1)。用循环伏安法可实现人血清中此2种血管疾病治疗药物的同时测定。     

基于PAMAM/聚2,6-吡啶二甲酸膜DNA电化学生物传感器的制备及对禽病毒基因检测的研究

以铂电极上聚合的2,6-吡啶二甲酸(PDC)膜组装G5.0树状高分子(PAMAM)固定ssDNA探针, 制备了一种新型的DNA电化学生物传感器. 用[Fe(CN)6]3－/4－作氧化还原指示剂, 以电化学交流阻抗和循环伏安技术对探针ssDNA的固定和杂交进行了表征. 实验表明, 当ssDNA在复合膜上固定及与其互补序列杂交后, 电极表面的传递电阻(Ret)依次增大. 因此, 可以利用Ret的明显差异, 以此固定探针的修饰电极, 对互补序列DNA进行无标记交流阻抗检测. 基于该生物传感器结合交流阻抗技术对禽病毒基因进行检测, 在优化实验条件下, 靶基因ssDNA-2在2.0×10－11～1.0×10－8 mol•L－1线性范围内, 其浓度与电极表面的电子传递电阻(Ret)之间呈良好的线性关系, 检测限为3.6×10－12 mol•L－1. 表明该方法为病毒灵敏地检测提供了一个有益的传感平台.     

Electrochemical Study and Application on Shikonin at Poly(diallyldimethylammonium chloride) Functionalized Graphene Sheets Modified Glass Carbon Electrode

The electrochemical behaviors of shikonin at a poly(diallyldimethylammonium chloride) functionalized graphene sheets modified glass carbon electrode(PDDA-GS/GCE) have been investigated. Shikonin could exhibit a pair of well-defined redox peaks at the PDDA-GS/GCE located at 0.681 V(E_pa) and 0.662 V(E_pc)[vs. saturated calomel electrode(SCE)] in 0.1 mol/L phosphate buffer solution(pH=2.0) with a peak-to-peak separation of about 20 mV, revealing a fast electron-transfer process. Moreover, the current response was remarkably increased at PDDA-GS/GCE compared with that at the bare GCE. The electrochemical behaviors of shikonin at the modified electrode were investigated. And the results indicate that the reaction involves the transfer of two electrons, accompanied by two protons and the electrochemical process is a diffusional-controlled electrode process. The electrochemical parameters of shikonin at the modified electrode, the electron-transfer coefficient(α), the electron-transfer number(n) and the electrode reaction rate constant(k_s) were calculated to be as 0.53, 2.18 and 3.6 s^-1, respectively. Under the optimal conditions, the peak current of differential pulse voltammetry(DPV) increased linearly with the shikonin concentration in a range from 9.472×10^-8 mol/L to 3.789×10^-6 mol/L with a detection limit of 3.157×10^-8 mol/L. The linear regression equation was I_p=0.7366c+0.7855(R=0.9978; I_p: 10^-7 A, c: 10^-8 mol/L). In addition, the modified glass carbon electrode also exhibited good stability, selectivity and acceptable reproducibility that could be used for the sensitive, simple and rapid determination of shikonin in real samples. Therefore, the present work offers a new way to broaden the analytical application of graphene in pharmaceutical analysis.     

Development of an Electrochemical Sensor for Selective Determination of Dopamine Based on Molecularly Imprinted Poly(p-aminothiophenol) Polymeric Film

In this study, a molecularly imprinted electrochemical sensor (MIP/DA) was investigated for selective and sensitive determination of dopamine (DA) by electrochemical polymerization of p-aminothiophenol in the presence of DA on gold electrode. According to electrochemical behaviour of the sensor, gained through cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS), MIP/DA sensor showed distinctive electron transfer characteristics in comparison to the non-imprinted (NIP/DA) sensor. Besides the MIP/DA sensor showed high selectivity for dopamine through its analyte specific cavities. The sensor had a broad working range of 5.0×10⁻⁸–2.0×10⁻⁷ M with a limit of detection (LOD) of 1.8×10⁻⁸ M and the developed sensor was successfully applied for determination of dopamine in pharmaceutical samples.     

A Nitrite Electrochemical Sensor Based on Boron‐Doped Diamond Planar Electrochemical Microcells Modified with a Monolacunary Silicotungstate Polyoxoanion

A new boron doped diamond microcells (BDD) was modified, for rapid, selective and highly sensitive determination of nitrite, using a coating film of polyoxometalates (POMs), formed by cyclic voltammetry on the molecular p‐phenylenediamine (PPD) functionalized BDD. The scanning electron microscopy (SEM) technique was used to examine the morphology of (PPD/SiW₁₁) modified (BDD) electrode. It was found that (SiW₁₁) layer was uniformly formed on the electrode surface. It was observed that (BDD/PPD/SiW₁₁) showed excellent electrocatalytic activities towards nitrite ion. Under the selected conditions, the anodic peak maximum at ?0.6 V was linear versus nitrite concentration in the 40 µM–4 mM range, and the detection limit obtained was 20 µM. The newly developed electrode has been successfully applied to the determination of nitrite content in real river water samples.     

对羟基苯甲酸酯分子印迹电化学传感器的研制

利用分子印迹技术,以对羟基苯甲酸乙酯为模板分子,甲基丙烯酸为单体,在玻碳电极表面原位聚合分子印迹聚合物敏感膜.采用方波伏安法对对羟基苯甲酸乙酯在该印迹电极上的电化学行为进行了研究,当响应时间为15 min时,0.95 V(vs SCE)处的峰电流与对羟基苯甲酸乙酯的浓度在2.0×10-6 ～2.0×10-4 mol/L范围内呈线性关系,检出限(S/N=3)为1.0 μmol/L,而相同条件下,对羟基苯甲酸乙酯在控制电极上的响应非常小并对浓度变化不灵敏;同时在印迹电极上氧化峰电位较在裸电极上发生了微弱正移.同一支印迹电极对对羟基苯甲酸乙酯响应值的RSD为4.3%(n=10).该印迹电极对尼泊金酯类具有良好的选择性,对对羟基苯甲酸甲酯、丙酯以及丁酯的选择性系数分别为1.89、1.70和2.01;对结构相似的苯酚、对羟基苯甲酸、对氨基苯甲酸等响应不灵敏,对结构差异较大的如维生素C等几乎无响应.用该分子印迹电极对实际样品进行分析,加标回收率大于90%.     

Electrochemical Sensor Based on Oxidation of 2,8‐Dihydroxyadenine to Monitor DNA Damage in Calf Thymus DNA

A novel and reliable direct electrochemical method has been established to monitor DNA damage in acid hydrolyzed calf thymus DNA, based on the determination of 2,8‐dihydroxyadenine (2,8‐DHA). A single‐wall carbon nanotubes (SWCNT) modified edge plane pyrolytic graphite electrode (EPPGE) has been used as a sensor to monitor the DNA damage. 2,8‐DHA the main in vivo adenine oxidation product undergoes oxidation at ～395 mV at SWCNT modified EPPGE using square wave voltammetry (SWV). The sensor exhibits potent and persistent electron‐mediating behavior. A well‐defined oxidation peak for the oxidation of 2,8‐DHA was observed at modified electrode with lowering of peak potential and increase in peak current as compared to bare EPPGE. At optimal experimental conditions, the catalytic oxidative peak current was responsive with the 2,8‐DHA concentrations ranging from 0.05 nM to 100 nM. The detection limit was 3.8×10^?11 M and limit of quantification was 1.27×10^?10 M. The modified electrode exhibited high stability and reproducibility.     

A Simple,Efficient and Ultrasensitive Gold Nanourchin Based Electrochemical Sensor for the Determination of an Antimalarial Drug: Mefloquine

Mefloquine (MQ) is a quinoline based antimalarial drug, which is potent against multiple drug‐resistant Plasmodium falciparum . It is widely prescribed for the prophylactic treatment of malaria. Due to extensive usage of MQ, constant monitoring of the drug level in human body is of paramount importancein order to ensure that optimum drug exposure is achieved. The present work describes a gold nanourchins (AuNUs) based electrochemical sensor for the determination of MQ.AuNUs were synthesized via seed‐mediated method and characterized using ultraviolet‐visible spectroscopy, energy‐dispersive X‐ray spectroscopy, field emission scanning electron microscopy, zeta‐sizer and electrochemical techniques (electrochemical impedance spectroscopy and cyclic voltammetry). Fabrication of the sensor was done by drop‐coating the synthesized AuNUs onto a glassy carbon electrode. The fabricated sensor exhibited enhanced voltammetric response, which was attributed to the excellent conductivity and high surface area of AuNUs. Under optimum square wave voltammetric conditions, the sensor displayed two linear response ranges (from 2.0×10⁻⁹ to 1.0×10⁻⁶ M and from 1.0×10⁻⁶ to 1.0×10⁻³ M) with a detection limit of 1.4 nM. The electrode demonstrated good reproducibility, stability and selectivity over common interferents. The utility of the sensor was successfully assessed for quantification of the drug in pharmaceutical preparation and spiked human urine sample. Thus, the present study demonstrates a promising approach for determination of MQ with practical utility in quality control and clinical analysis.     

A Highly Sensitive Sensor Based on Reduced Graphene Oxide,Carbon Nanotube and a Co(II) Complex Modified Carbon Paste Electrode: Simultaneous Determination of Isoprenaline,Captopril and Tryptophan

This paper describes the development of a reduced graphene oxide (RGO), carbon nanotube (CNT) and Co(II) complex (cobalt(II) bis (benzoylacetone) ethylenediimino) (CBE) modified carbon paste electrode (CPE) for simultaneous determination of isoprenaline (IP), captopril (CAP) and tryptophan (Try). A pair of well‐defined redox peaks of Co(II) complex were obtained through a direct electron transfer between the Co(II) complex and the CPE. The proposed sensor showed very efficient electrocatalytic activity for anodic oxidation of IP in a 0.1 M phosphate buffer solution (pH 7.0). Square wave voltammetry (SWV) exhibited two linear dynamic ranges of 0.125–30.0 µM and 30.0–300.0 µM for IP. The detection limit for IP was found to be 50 nM. The proposed sensor was successfully applied for the determination of IP in real samples such as human blood serum, urine and IP ampoule.     

基于银纳米粒子/氧化石墨烯复合薄膜制备TNP电化学传感器

利用改进的Hummers法制备了氧化石墨烯(GO), 以葡萄糖为还原剂直接在GO表面沉积银纳米粒子(AgNPs)得到性能稳定的AgNPs/GO纳米复合材料;基于该纳米复合材料修饰电极构建了一种新型的2, 4, 6-三硝基苯酚(TNP)电化学传感器。采用原子力显微镜(AFM)、扫描电镜(SEM)、透射电镜(TEM)、紫外可见光谱(UV-Vis)和交流阻抗(EIS)等多种方法对纳米复合薄膜进行了表征;并研究了TNP在复合薄膜修饰电极上的电化学行为和动力学性质。结果表明, AgNPs/GO对TNP有较强的电催化活性, 在复合薄膜修饰电极出现一灵敏的氧化峰和3个还原峰;利用氧化峰可对TNP进行定量分析。同时整个电极过程明显不可逆, 电极反应受到吸附步骤控制;复合膜电极表面覆盖度为5.617×10^-8 mol·cm^-2, 在所研究电位下的速率常数为9.745×10^-5 cm·s^-1。在pH 6.8的磷酸缓冲液中, 当富集电位为-0.70 V, 富集时间为60 s;TNP氧化峰电流与其浓度在5.0×10^-9~1.0×10^-7 mol·L^-1范围内成良好线性关系, 相关系数为0.995 8, 检出限可达1.0×10^-9 mol·L^-1。所制备的电化学传感器稳定性和选择性较好;用于实际水样中TNP的现场快速检测, 加标回收率在 97.6%~103.9%之间。     

Development of a Molecularly Imprinted Poly(Acrylic Acid)‐MWCNT Nanocomposite Electrochemical Sensor for Tramadol Determination in Pharmaceutical Samples

A new voltammetric sensor based on molecularly imprinted poly(acrylic acid)‐MWCNT nanocomposite (MIP‐MWCNT) drop‐coated onto glassy carbon electrode (GCE) was developed and applied to tramadol (TR) determination in pharmaceutical samples. The voltammetric sensor prepared by suspension of MIP‐MWCNT at 1 : 1 (w/w) ratio show an improved performance compared to unmodified GCE. The electrochemical method is based on preconcentration of tramadol onto MIP‐MWCNT modified GCE surface at ?1.5 V vs Ag/AgCl for 180 s in 0.1 Britton‐Robinson buffer (pH 8.0) at stirred solution. Upon preconcentration, the differential anodic voltammogram was recorded under the optimized condition giving rise to an analytical curve varying from 9.0 up to 30.0 μmol L^?1 (R²=0.997) and limits of detection and quantification of 1.4 and 4.8 μmol L^?1, respectively. The method precision was assessed in terms of intraday (n=6) and interday (two consecutive days) precision, giving relative standard deviations (RSD%) values between 2.8 to 7.4 %. Excipients usually found in pharmaceutical pills (magnesium stearate, microcrystalline cellulose, starch, and silica) and paracetamol were evaluated as potential interferents, however no interference was evidenced in TR determination. The method applicability was evaluated by TR analysis in pharmaceutical samples. Moreover, the method accuracy was attested by comparison of addition and recovery assays with a reference technique (high‐performance liquid chromatography).     

Construction and Application of an Electrochemical Sensor for Simultaneous Determination of Cd(II), Cu(II) and Hg(II) in Water and Foodstuff Samples

By incorporation of synthesized magnetite nanoparticles (Fe₃O₄ NPs) coated with a new Schiff base into carbon paste electrode, a novel modified electrode was constructed for simultaneous determination of ultra trace amounts of Cd(II), Cu(II) and Hg(II). The complexation reaction of Schiff base with metal ions was studied spectrophotometrically. Under optimal conditions a detection limit of 0.20, 0.90 and 1.00 ng mL^?1 for Cd(II), Cu(II) and Hg(II), respectively, was obtained. We take the advantages of the proposed method for simple, rapid, sensitive and selective simultaneous determination of trace amounts of hazardous Cd(II), Cu(II) and Hg(II) in water and foodstuff samples.