碳纤维表面改性研究进展

碳纤维因其优异的综合性能常被用作树脂基体的增强材料.然而由于碳纤维与树脂基体之间的界面结合性能较差,其增强的复合材料的力学性能往往与理论值相差甚远,因此必须对碳纤维进行表面改性,以提高其与聚合物基体的界面粘结性能.本文作者综述了国内外关于碳纤维表面改性技术的研究进展,概述了涂层法、氧化法、高能辐射法等改性方法对碳纤维增强复合材料界面强度的改性效果.     

碳纳米管修饰碳纤维超微圆柱电极的研制与应用

制作了碳纳米管修饰碳纤维组合电极(EUME-CNT),研究了木犀草素在EUME-CNT上的电化学行为,并且通过优化测定参数,建立了木犀草素的电化学分析方法。检出限达到4×10-7mol/L,线性范围为6×10-7~1×10-5mol/L。     

Surface modification of carbon fiber for improving the interfacial adhesion between carbon fiber and polymer matrix

In this study, the reinforcing mechanism of amine functionalized on carbon fibers (CFs) has been precisely discussed, and the differences between aliphatic and aromatic compounds have been illustrated. Polyacrylonitrile‐based CFs were functionalized with ethylenediamine, 4,4‐diaminodiphenyl sulphone, and p‐aminobenzoic acid (PAB), and CF‐reinforced epoxy composites were prepared. The structural and surface characteristics of the functionalized CFs were investigated using X‐ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FT‐IR), and scanning electron microscopy (SEM). Mechanical properties in terms of tensile and flexural strengths and moduli were studied. The FT‐IR results confirm the success in bonding amines on the CF surface. After treatment of CFs, the oxygen and nitrogen contents as well as the N/C ratio showed an increase. XPS results provided evidence of the chemical reaction during functionalization, rather than being physically coated on the CF surface. Chemical modification of CF with diamines led to considerable enhancement in compatibility of CF filaments and epoxy resin, and remarkable improvements were seen in both tensile and flexural properties of the reinforced composites. SEM micrographs also confirmed the improvement of interface adhesion between the modified CFs and epoxy matrix. Finally, it can be concluded that PAB is a promising candidate to functionalize CF in order to improve interfacial properties of CF/epoxy composites. Copyright © 2015 John Wiley & Sons, Ltd.     

The surface modification of carbon fiber for thermoplastic HDPE composites

The interfacial adhesion strength between the fiber and the matrix greatly affects the properties of the carbon fiber (CF)–reinforced composite. The presence of surface functional groups on the fiber and changes in surface roughness were determined by X-ray photoelectron spectroscopy, scanning electron microscopy (SEM), and Raman spectroscopy. The effect of surface modification of CF on the mechanical properties and tribological properties of the composites is enhanced. The performance has been significantly improved. SEM analysis showed that modification had a positive effect on the interface between fiber and matrix. In the paper, the method of CF modification and the treatment of enhanced high-density polyethylene have simple and effective characteristics, which can be widely used and have guiding significance for industrial production.     

DNA纳米网络修饰碳纤维盘电极及其分子传感应用

DNA immobilization on electrode surfaces has been widely used for fabricating sensors since DNA can interact with a wide variety of biomolecules. Recendy, DNA has been demonstrated as an electronic super conductor and become the most promising biomolecule for application of chemical sensing in biological system. Calf thymus DNA (ct-DNA) is a most popularly used native DNA in many applications. An electrochemical deposition on carbon fiber micro electrode can provide sensitive detection of dopamine in presence of large amount of ascorbic acid.     

Ensemble of carbon fiber ultra-microelectrodes modified with nanotubes, and its application to the determination of dopamine

An ensemble of carbon fibers ultra-microelectrode modified with carbon nanotubes (EUME-CNTS) has been constructed based on a thin carbon nanotubes film which was coated onto surfaces of carbon fibers of ultra-microelectrode. SEM micrographs illustrated the image of carbon nanotubes on the carbon fiber surface. The electrochemical characteristics of the EUME-CNTS has been investigated by cyclic voltammetry. The electrochemical properties of dopamine on this electrode were also studied, and the detection limit was found to be 2.0 × 10⁻⁹ mol·L⁻¹. Linear calibration plots were obtained for the oxidation peak current in a range 1.0 × 10⁻⁷–8.0 × 10⁻⁵ mol·L⁻¹. Correspondence: Xiuhua Liu, Kuaizhi Liu, Department of Chemistry and Chemical Engineering, Henan University, Henan Kaifeng 475001, P.R. China     

MoS2 incorporated carbon allotropes (activated carbon,graphene, MWCNT) as electrodes in symmetric supercapacitors

Symmetric supercapacitor devices were fabricated from MoS₂ incorporated carbon allotropes such as activated carbon (AC)/MoS₂, graphene/MoS₂ and MWCNT/MoS₂. The device performance was evaluated using cyclic voltammetry (CV), galvanostatic charge-discharge (GCD), and electrochemical impedance spectroscopy (EIS). The electrochemical properties of the devices fabricated from carbon allotropes (activated carbon, graphene, MWCNT) were remarkably enhanced to above 50% by the incorporation MoS₂ phases. Out of the three fabricated devices, electrochemical performance of AC/MoS₂ as found to be superior. The specific capacitance and energy density of this device is 216 ​F/g and 6.2 ​Wh/Kg respectively with excellent higher rate capability and longer cyclic durability. The devices fabricated from graphene/MoS₂ and MWCNT/MoS₂ has exhibited a specific capacitance value of 202 ​F/g and 161 ​F/g with an energy density value of 5.68 ​Wh/Kg and 3.95 ​Wh/Kg respectively.     

Surface modification of carbon fiber via electron‐beam irradiation grafting

In this paper, the surface properties of polyacrylonitrile‐based carbon fibers is improved by electron‐beam (EB) irradiation in maleic anhydride/acetone solution at 100, 150, 200 and 150 KGy. Experimental study of this paper is carried out to identify surface topography, surface chemical composition and functional groups, adsorption ability and interface properties of CF/epoxy composites. The results reveal that the roughness of carbon fiber surface is increased obviously after modification by EB irradiation grafting technology. The ratio value of O/C and the relative content of oxygen functional groups on fiber surface are improved effectively, comparing with the unmodified carbon fiber. Besides, adsorption of carbon fiber on epoxy and the mechanical performance of CF/epoxy composites are clearly enhanced after irradiation grafting modification. Copyright © 2012 John Wiley & Sons, Ltd.     

A review of heat treatment on polyacrylonitrile fiber

Developing carbon fiber from polyacrylonitrile (PAN) based fiber is generally subjected to three processes namely stabilization, carbonization, and graphitization under controlled conditions. The PAN fiber is first stretched and simultaneously oxidized in a temperature range of 200-300 °C. This treatment converts thermoplastic PAN to a non-plastic cyclic or a ladder compound. After oxidation, the fibers are carbonized at about 1000 °C in inert atmosphere which is usually nitrogen. Then, in order to improve the ordering and orientation of the crystallites in the direction of the fiber axis, the fiber must be heated at about 1500-3000 °C until the polymer contains 92-100%. High temperature process generally leads to higher modulus fibers which expel impurities in the chain as volatile by-products. During heating treatment, the fiber shrinks in diameter, builds the structure into a large structure and upgrades the strength by removing the initial nitrogen content of PAN precursor and the timing of nitrogen. With better-controlled condition, the strength of the fiber can achieve up to 400 GPa after this pyrolysis process.     

Development and evaluation of electrochemical glucose enzyme biosensors based on carbon film electrodes

Electrochemical glucose enzyme biosensors have been prepared on carbon film electrodes made from carbon film electrical resistors. Evaluation and characterisation of these electrodes in phosphate buffer saline solution has been carried out with and without pretreatment by cycling in perchloric acid or at fixed applied potential. Both pretreatments led to a reduction in the carbon surface oxidation peak and enabled better detection of hydrogen peroxide in the pH range of 5-7. Glucose oxidase enzyme was immobilised on the carbon surface by mixing with glutaraldehyde, bovine serum albumin and with and without Nafion. The performance of these two types of electrode was similar, that containing Nafion being more physically robust. Linear ranges were up to around 1.5 mM, with detection limits 60 μM, and pretreatment of the carbon film electrode at a fixed potential of +0.9 V versus SCE for 5 min was found to be the most beneficial. Michaelis-Menten constants between 5 mM and 10 mM were found under the different experimental conditions. Coating the immobilised enzyme layer with a thin layer of Nafion was found to give similar results in the determination of glucose to mixing it but with benefits against interferences for the analysis of complex matrices, such as wine. Potentialities, for a short-term-use or disposable sensors, are indicated.     

A review of linear carbon chains

Linear carbon chains (LCCs) are a one-dimensional sp¹-hybridized allotrope of carbon. LCCs are extremely unstable: The longer the LCCs, the less stable the materials. Thus, it is a big challenge to synthesize long LCCs. Although the research on the short LCCs, e.g., polyynes, can be traced back to the 18^th, LCCs are still not well-known compared to other allotropes of carbon, e.g., fullerenes, carbon nanotubes and graphene. Therefore, introducing recent progress on LCCs is of great significance to draw more attention in the community of nanocarbons as well as nanomaterials in general. Theoretically, various excellent properties have been predicted. Experimentally, LCCs with different length in many kinds of forms have been successfully synthesized. In this review, we summarized recent studies of polyynic LCCs from both theoretical and experimental aspects. Also, perspectives are highlighted to point out the further investigations of the materials.     

Application of novel activated carbon fiber solid-phase, microextraction to the analysis of chlorinated hydrocarbons in water by gas chromatography-mass spectrometry

This paper presents a study on the performance of activated carbon fiber (ACF) used as extraction fiber for solid-phase microextraction (SPME) and its application for analysis of chlorinated hydrocarbons in water. By means of evaluating scanning electron microscope (SEM) images, specific surface area, pore volume, pore distribution, and properties of adsorption and desorption, the optimal active concentration of phosphoric acid has been determined. Coupled with gas chromatograph-mass spectrometry (GC-MS), ACF-SPME is suitable for determination chlorinated hydrocarbons in water with headspace. Experimental parameters such as adsorption and desorption conditions were studied. The optimized method has an acceptable linearity, good precision, with R.S.D. values <10% for each compound. Compared with commercial fibers, ACF has many advantages such as better resistance to organic solvents, better endurance to high temperature and longer lifetime.     

Performance of PbO2/activated carbon hybrid supercapacitor with carbon foam substrate

PbO₂/activated carbon（AC） hybrid supercapacitor in H₂SO₄ with a carbon foam current collector is studied.The PbO₂/AC hybrid is designed with electrodeposited PbO₂ thin film as positive electrode to match with AC negative electrode.The discharge curve shows capacitive characteristics between 1.88 V and 0.65 V.The hybrid system exhibits excellent energy and power performance,with specific energy of 43.6 Wh/kg at a power density of 654.2 W/kg.The use of carbon foam current collector ensures stability of the PbO₂ electrode in H₂SO₄ environment.After 2600 deep cycles at 15 C high rate of charge/discharge,the capacity remains nearly unchanged from its initial value.     

Ultra high density carbon fiber derived from isotactic polypropylene fiber without skin-core structure

Polypropylene (PP)-based carbon fibers were prepared by sulfonation process of isotactic PP fibers with concentrated sulfuric acid, followed by stress-less carbonization under nitrogen atmosphere. The stabilization behaviors of PP fiber under different sulfonation temperatures and time were discussed. The carbonization behavior of the stabilized PP fibers under different carbonization temperatures, as well as the mechanical performance of the obtained carbon fibers were investigated. The results indicated that linear PP molecule were effectively converted into thermally stable structure at higher temperature (≥130°C) in short time (2 h) through sulfonation-desulfonation reaction, among which ordered graphite structure has been formed prior to the carbonization process. Meanwhile, the carbon fibers were considerably densified by increasing the sulfonation temperature and carbonization temperature, and a bulk density of 1.96 g/cm³ was achieved. Moreover, the temperature and time of the sulfonation process as well as the temperature of the carbonization process were regulated, and carbon fibers with tensile strength of 262.3 MPa was obtained, which was superior to that of 208.1 MPa for the linear low density polyethylene-based carbon fibers reported previously. Isotactic PP was proved to be a promising candidate to develop carbon fibers with tunable graphite structure and mechanical performance.     

Recycling of carbon fibre reinforced polymeric waste for the production of activated carbon fibres

Composite waste composed of carbon fibres and polybenzoxazines resin has been pyrolysed in a fixed bed reactor at temperatures of 350, 400, 450, 500 and 700 °C. Solid residues of between 70 and 83.6 wt%, liquid yields 14 and 24.6 wt% and gas yields 0.7 and 3.8 wt% were obtained depending on pyrolysis temperature. The derived pyrolysis liquids contained aniline in high concentration together with oxygenated and nitrogenated aromatic compounds. The pyrolysis gases consisted mainly of CO₂, CO, CH₄, H₂ and other hydrocarbons. The carbon fibres used in the composite waste were separated from the char of the solid residue via oxidation of the char at two different temperatures and investigated for their mechanical strength properties. The carbon fibres recovered from the sample pyrolysed at 500 °C and oxidised at 500 °C exhibited mechanical properties which were 90% of that of the original virgin carbon fibres. Steam activation of the recovered carbon fibres was carried out at 850 °C at different times of activation. The effect of activation time on BET surface area, activated carbon fibres yield, porosity and the morphological structure of activated carbon fibres was evaluated. A maximum BET surface area of over 800 m² g⁻¹ was obtained for the activated carbon fibres produced at 850 °C for 5 h of activation. Nitrogen adsorption-desorption isotherms showed that the adsorption capacity increased as the activation time increased up to 5 h of activation and then after that decreased.     

Electrochemical determination of naproxen in the presence of acetaminophen using a carbon paste electrode modified with activated carbon nanoparticles

In this study, cyclic voltammetry and differential pulse voltammetry were used to determine the electrochemical properties and concentration of naproxen in pharmaceutical formulation and human serum samples by using a carbon paste electrode modified with activated carbon nanoparticles. Optimum conditions were obtained at an electrode with 0.005 g activated carbon nanoparticles in a phosphate buffer solution of pH 6 as a supporting electrolyte. Linear calibration curves were obtained in the range of 0.1–120 μM, and the detection limit of naproxen determined was 0.0234 μM. The modified electrode shows good selectivity for naproxen in the presence of some organic and inorganic interferences and very good precision in real samples. Finally, naproxen was measured in the presence of acetaminophen.     

Comparison of four methods for determining fiber content of carbon fiber/epoxy composites

The most fundamental parameter that controls the properties of fiber/epoxy composites is fiber content. Thus, exact calculation of carbon fiber content is important for product quality control and process optimization. In this study, four methods for calculating fiber content of continuous carbon fiber/epoxy composites were investigated. These four methods are processing statistical (PS), optical microscopy (OM), thermogravimetric analysis (TGA), and carbonization-in-nitrogen (CIN). The results show that the CIN and PS methods have high repeatability with no more than 4.7 wt.% deviation, and a relatively exact estimation of fiber content can be obtained by using both of them. A larger difference was generated when the TGA and OM methods were used to determine the fiber content. This is because the small amount of samples required by these methods is not sufficiently representative of the whole carbon fiber composite structure. The PS and CIN methods can be used as approved ways to calculate fiber content of carbon fiber/epoxy composites effectively.     

Preparation and Characterization of Antibacterial Polyacrylonitrile-based Activated Carbon Fiber Supporting Nano-ZnO

Polyacrylonitrile(PAN)-based activated carbon fiber(PACF) supporting nano-ZnO(PACF /nano-ZnO) was prepared by spin, pretreatment, carbonization, and KOH chemical activation at an activation temperature of 950 ℃ for 40 min. Nano-ZnO content, distribution and antibacterial properties of the PACF/nano-ZnO were studied. The pore structure and surface properties of the PACF/nano-ZnO were studied by Brunauer-Emmett-Teller(BET), N₂/77 K isothermal adsorption. The specific surface area increased markedly after the activation process and it was several hundred times greater than that before the process. The PACF/nano-ZnO shows a strong adsorption for Staphylococcus aureus(S. aureus) and Escherichia coli(E. coli) and antibacterial activity against them. As an experimental result, antibacterial properties of PACF/nano-ZnO increased with increasing the concentration of nano-ZnO particles, which suggests it is a promising antibacterial material.     

Voltammetry and determination of metronidazole at a carbon fiber microdisk electrode

The electrochemistry of metronidazole, 1-(hydroxyethyl)-2-methyl-5-nitroimidazole, was investigated at a carbon fiber microdisk electrode in pH 9 Britton Robinson buffer. Under these conditions, the reduction of metronidazole is controlled by both mass transport to the microdisk and adsorption with an equilibrium constant of 4 × 10³ mol⁻¹ dm³ and a saturation coverage of 0.88 × 10⁻⁸ mol cm⁻². The adsorption and accumulation of metronidazole on the surface of the carbon fiber allows its determination at low concentrations by square wave adsorptive stripping voltammetry. A detection limit for metronidazole of 5 × 10⁻⁷ mol dm⁻³ and a R.S.D. of 3.7% at 1 × 10⁻⁶ mol dm⁻³ (n = 4) were obtained with a two electrode system with no stirring during the accumulation step. Based on this method, a simple procedure for the determination of metronidazole in urine is described which requires no pre-treatment of the sample before analysis.