Consecutive Charging of a Perylene Bisimide Dye by Multistep Low-Energy Solar-Light-Induced Electron Transfer Towards H2 Evolution

A photocatalytic system containing a perylene bisimide (PBI) dye as a photosensitizer anchored to titanium dioxide (TiO₂) nanoparticles through carboxyl groups was constructed. Under solar-light irradiation in the presence of sacrificial triethanolamine (TEOA) in neutral and basic conditions (pH 8.5), a reaction cascade is initiated in which the PBI molecule first absorbs green light, giving the formation of a stable radical anion (PBI^.−), which in a second step absorbs near-infrared light, forming a stable PBI dianion (PBI²⁻). Finally, the dianion absorbs red light and injects an electron into the TiO₂ nanoparticle that is coated with platinum co-catalyst for hydrogen evolution. The hydrogen evolution rates (HERs) are as high as 1216 and 1022 μmol h⁻¹ g⁻¹ with simulated sunlight irradiation in neutral and basic conditions, respectively.     

Production of Hydrogen by Glycerol Photoreforming Using Binary Nitrogen–Metal‐Promoted N‐M‐TiO2 Photocatalysts

The need for renewable energy focuses attention on hydrogen obtained by using sustainable and green methods. The sustainable compound glycerol can be used for hydrogen production by heterogeneous photocatalysis. A novel approach involves the promotion of the TiO₂ photocatalyst with a binary combination of nitrogen and transition metal. We report the synthesis and spectroscopic characterization of the new N‐M‐TiO₂ photocatalysts (M=none, Cr, Co, Ni, Cu), and the photocatalytic reforming of glycerol to hydrogen under ambient conditions and near‐UV or visible light versus benchmark P25 TiO₂. In units of activity μmol m^?2 h^?1, N‐Ni‐TiO₂ is five‐fold more active than P25, and N‐Cu‐TiO₂ is 44‐fold more active. The photocatalytic activity of N‐M‐TiO₂ increases from Cr to Co and Ni, whereas the photoluminescence decreases; the change in activity is due to the modulation of charge recombination.     

Facile Synthesis of Thermal‐ and Photostable Titania with Paramagnetic Oxygen Vacancies for Visible‐Light Photocatalysis

A novel dopant‐free TiO₂ photocatalyst (V_o^.‐TiO₂), which is self‐modified by a large number of paramagnetic (single‐electron‐trapped) oxygen vacancies, was prepared by calcining a mixture of a porous amorphous TiO₂ precursor, imidazole, and hydrochloric acid at elevated temperature (450 °C) in air. Control experiments demonstrate that the porous TiO₂ precursor, imidazole, and hydrochloric acid are all necessary for the formation of V_o^.‐TiO₂. Although the synthesis of V_o^.‐TiO₂ originates from such a multicomponent system, this synthetic approach is facile, controllable, and reproducible. X‐ray diffraction, XPS, and EPR spectroscopy reveal that the V_o^.‐TiO₂ material with a high crystallinity embodies a mass of paramagnetic oxygen vacancies, and is free of other dopant species such as nitrogen and carbon. UV/Vis diffuse‐reflectance spectroscopy and photoelectrochemical measurement demonstrate that V_o^.‐TiO₂ is a stable visible‐light‐responsive material with photogenerated charge separation efficiency higher than N‐TiO₂ and P25 under visible‐light irradiation. The V_o^.‐TiO₂ material exhibits not only satisfactory thermal‐ and photostability, but also superior photocatalytic activity for H₂ evolution (115 μmol h^?1 g^?1) from water with methanol as sacrificial reagent under visible light (λ>400 nm) irradiation. Furthermore, the effects of reaction temperature, ratio of starting materials (imidazole:TiO₂ precursor) and calcination time on the photocatalytic activity and the microstructure of V_o^.‐TiO₂ were elucidated.     

Activation of CH Bonds through Oxidant‐Free Photoredox Catalysis: Cross‐Coupling Hydrogen‐Evolution Transformation of Isochromans and β‐Keto Esters

The direct and controlled activation of a C(sp³)?H bond adjacent to an O atom is of particular synthetic value for the conventional derivatization of ethers or alcohols. In general, stoichiometric amounts of an oxidant are required to remove an electron and a hydrogen atom of the ether for subsequent transformations. Herein, we demonstrate that the activation of a C?H bond next to an O atom could be achieved under oxidant‐free conditions through photoredox‐neutral catalysis. By using a commercial dyad photosensitizer (Acr⁺‐Mes ClO₄^?, 9‐mesityl‐10‐methylacridinium perchlorate) and an easily available cobaloxime complex (Co(dmgBF₂)₂?2 MeCN, dmg=dimethylglyoxime), the nucleophilic addition of β‐keto esters to oxonium species, which is rarely observed in photocatalysis, leads to the corresponding coupling products and H₂ in moderate to good yields under visible‐light irradiation. Mechanistic studies suggest that both isochroman and the cobaloxime complex quench the electron‐transfer state of this dyad photosensitizer and that benzylic C?H bond cleavage is probably the rate‐determining step of this cross‐coupling hydrogen‐evolution transformation.     

Photocatalytic Activity for Water Decomposition to Hydrogen over Nitrogen‐doped TiO2 Nanoparticle

Nitrogen-doped TiO2 nanoparticle photocatalysts were obtained by an annealing method with gaseous ammonia and nitrogen. The influence of dopant N on the crystal structure was characterized by XRD, XPS, BET, TEM and UV-Vis spectra. The results of XRD indicate that, the crystal phase transforms from anatase to rutile structure gradually with increase of annealing temperature from 300 to 700 ℃. XPS studies indicate that the nitrogen atom enters the TiO2 lattice and occupies the position of oxygen atom. Agglomeration of particles is found in TEM images after annealing. BET results show that the specific surface areas of N-doped samples from 44.61 to 38.27 m2/g are smaller than that of Degussa TiO2. UV-Vis spectra indicate that the absorption threshold shifts gradually with increase of annealing temperature, which shows absorption in the visible region. The influence of annealing condition on the photocatalytic property has been researched over water decomposition to hydrogen, indicating that nitrogen raises the photocatalytic activity for hydrogen evolution, and the modified TiO2 annealed for 2 h at 400 ℃ under gas of NH3/N2 (V/V＝1/2) mixture shows better efficiency of hydrogen evolution. Furthermore, the N-doped TiO2 nanoparticle catalysts have obvious visible light activity, evidenced by hydrogen evolution under visible light (λ＞400 nm) irradiation. However, the catalytic activity under visible light irradiation is absent for Degussa as reference and the N-doped TiO2 annealed at 700 ℃.     

Spin–Orbit Charge-Transfer Intersystem Crossing in Anthracene–Perylenebisimide Compact Electron Donor–Acceptor Dyads and Triads and Photochemical Dianion Formation

Perylenebisimide ( PBI )–anthracene ( AN ) donor–acceptor dyads/triad were prepared to investigate spin–orbit charge-transfer intersystem crossing (SOCT-ISC). Molecular conformation was controlled by connecting PBI units to the 2- or 9-position of the AN moiety. Steady-state, time-resolved transient absorption and emission spectroscopy revealed that chromophore orientation, electronic coupling, and dihedral angle between donor and acceptor exert a significant effect on the photophysical property. The dyad PBI-9-AN with orthogonal geometry shows weak ground-state coupling and efficient intersystem crossing (ISC, Φ_Δ=86 %) as compared with PBI-2-AN (Φ_Δ=57 %), which has a more coplanar geometry. By nanosecond transient absorption spectroscopy, a long-lived PBI localized triplet state was observed (τ_T=139 μs). Time-resolved EPR spectroscopy demonstrated that the electron spin polarization pattern of the triplet state is sensitive to the geometry and number of AN units attached to PBI . Reversible and stepwise generation of near-IR-absorbing PBI radical anion ( PBI^−⋅ ) and dianion ( PBI²⁻ ) was observed on photoexcitation in the presence of triethanolamine, and it was confirmed that selective photoexcitation at the near-IR absorption bands of PBI^.− is unable to produce PBI²⁻ .     

Multifunctional Nitrogen‐Doped Carbon Nanodots for Photoluminescence,Sensor, and Visible‐Light‐Induced H2 Production

Herein, multifunctional N‐doped carbon nanodots (NCNDs) were prepared through the one‐step hydrothermal treatment of yeast. Results show that the NCNDs can be used as a new photocatalyst to drive the water‐splitting reaction under UV light. Moreover, the NCNDs can efficiently catalyze the hydrogen evolution reaction. Under visible‐light irradiation, Eosin Y‐sensitized NCNDs exhibit excellent activity for hydrogen evolution. The hydrogen evolution rate of NCNDs (without any modification and co‐catalyst) reaches 107.1 μmol h^?1 (2142 μmol g^?1 h^?1). When Pt is loaded on the NCNDs, the hydrogen evolution rate reaches 491.2 μmol h^?1 (9824 μmol g^?1 h^?1) under visible‐light irradiation. In addition, the NCNDs show excellent fluorescent properties and can be applied as a fluorescent probe for the sensitive and selective detection of Fe³⁺.     

Ultrasonic Preparation of Hierarchical Graphene‐Oxide/TiO2 Composite Microspheres for Efficient Photocatalytic Hydrogen Production

Hierarchical graphene oxide (GO)‐TiO₂ composite microspheres with different GO/TiO₂ mass ratios were successfully prepared by mixing GO and TiO₂ microspheres under ultrasonic conditions. Ultrasonication helped the GO and TiO₂ microsphere to uniformly mix on the microscale. The results showed that the GO‐TiO₂ composites that were prepared by ultrasonic mixing exhibited significantly higher hydrogen‐evolution rates than those that were synthesized by simple mechanical grinding, owing to synergetic effects, including enhanced light absorption and scattering, as well as improved interfacial charge transfer because of the excellent contact between the GO sheets and TiO₂ microspheres. In addition, GO‐TiO₂‐3 (3 wt. % GO) showed the highest hydrogen‐generation rate (305.6 μmol h^?), which was about 13 and 3.3‐times higher than those of TiO₂ microsphere and GO‐P25 (with 3 wt. % GO), respectively. Finally, a tentative mechanism for hydrogen production is proposed and supported by photoluminescence and transient photocurrent measurements. This work highlights the potential applications of GO‐TiO₂ composite microspheres in the field of clean‐energy production.     

Electron Transfer in Dye‐Sensitised Semiconductors Modified with Molecular Cobalt Catalysts: Photoreduction of Aqueous Protons

A visible‐light driven H₂ evolution system comprising of a Ru^II dye ( RuP ) and Co^III proton reduction catalysts ( CoP ) immobilised on TiO₂ nanoparticles and mesoporous films is presented. The heterogeneous system evolves H₂ efficiently during visible‐light irradiation in a pH‐neutral aqueous solution at 25 °C in the presence of a hole scavenger. Photodegradation of the self‐assembled system occurs at the ligand framework of CoP , which can be readily repaired by addition of fresh ligand, resulting in turnover numbers above 300 mol H₂ (mol CoP )^?1 and above 200,000 mol H₂ (mol TiO₂ nanoparticles)^?1 in water. Our studies support that a molecular Co species, rather than metallic Co or a Co‐oxide precipitate, is responsible for H₂ formation on TiO₂. Electron transfer in this system was studied by transient absorption spectroscopy and time‐correlated single photon counting techniques. Essentially quantitative electron injection takes place from RuP into TiO₂ in approximately 180 ps. Thereby, upon dye regeneration by the sacrificial electron donor, a long‐lived TiO₂ conduction band electron is formed with a half‐lifetime of approximately 0.8 s. Electron transfer from the TiO₂ conduction band to the CoP catalysts occurs quantitatively on a 10 μs timescale and is about a hundred times faster than charge‐recombination with the oxidised RuP . This study provides a benchmark for future investigations in photocatalytic fuel generation with molecular catalysts integrated in semiconductors.     

Single‐Nanoparticle Collision Events: Tunneling Electron Transfer on a Titanium Dioxide Passivated n‐Silicon Electrode

Single‐nanoparticle collisions were observed on an n‐type silicon electrode (600 μm diameter) passivated by a thin layer of amorphous TiO₂, where the current steps occurred by tunneling electron transfer. The observed collision frequency was in reasonable agreement with that predicted from theory. The isolated electrode, after a collision experiment, with a Pt/TiO₂/n‐Si architecture was shown to retain the photoelectrochemical properties of n‐Si without photocorrosion or current decay. The Pt/TiO₂/n‐Si electrode produced 19 mA cm^?2 of photocurrent density under 100 mW cm^?2 irradiation from a xenon lamp during oxygen evolution without current fading for over 12 h.     

Gold‐Nanoparticle‐Loaded Carbonate‐Modified Titanium(IV) Oxide Surface: Visible‐Light‐Driven Formation of Hydrogen Peroxide from Oxygen

Gold nanoparticle‐loaded rutile TiO₂ with a bimodal size distribution around 10.6 nm and 2.3 nm (BM‐Au/TiO₂) was prepared by the deposition precipitation and chemical reduction (DP‐CR) technique. Visible‐light irradiation (λ>430 nm) of the BM‐Au/TiO₂ plasmonic photocatalyst yields 35 μm H₂O₂ in aerated pure water at irradiation time (t_p)=1 h, and the H₂O₂ concentration increases to 640±60 μm by the addition of 4 % HCOOH as a sacrificing electron donor. Further, a carbonate‐modified surface BM‐Au/TiO₂ (BM‐Au/TiO₂‐CO₃^2?) generates a millimolar level of H₂O₂ at t_p=1 h with a quantum efficiency (Φ) of 5.4 % at λ=530 nm under the same conditions. The recycle experiments confirmed the stable performance of BM‐Au/TiO₂.     

Efficient One-Pot Microwave-Assisted Hydrothermal Synthesis of Nitrogen-Doped TiO2 for Hydrogen Production by Photocatalytic Water Splitting

Develop a photocatalyst system for solar energy conversion to electric energy or chemical energy is a topic of great interest for fundamental and practical importance. In this study, nitrogen-doped TiO₂ with high hydrogen production by photocatalytic water splitting were prepared by microwave-assisted hydrothermal method using titanium sulfate as precursor in the presence of urea. The nitrogen doped TiO₂ prepared in this study was pure anatase phase with a high surface area (372?m²?g^?1) and showed a very high hydrogen evolution rate of water splitting reaction under UV light irradiation (4,386?μmol?g^?1?h^?1) and visible light irradiation (185?μmol?g^?1?h^?1) which was about 15?times higher than commercial TiO₂ (Degussa P25).     

Visible Light Photocatalytic Activity of Pt/N‐TiO2 towards Enhanced H2 Production from Water Splitting

Present work mainly focuses on experimental investigation to improvement of hydrogen production by water photoelectrolysis. An experimental facility was designed and constructed for visible light photocatalysis. A series of N‐TiO₂ photocatalysts impregnated with platinum on the surface of N‐TiO₂ were prepared. Hydrogen production upon irradiating aqueous Pt/N‐TiO₂ suspension with visible light was investigated. The shift in excitation wavelength of TiO₂ was 380 nm improved the yield of hydrogen production by N‐TiO₂ and Pt/N‐TiO₂. We used a 400 W mercury arc lamp combined with a 400 nm cutoff filter eliminating all the wavelengths under 400 nm. Pt/N‐TiO₂ material was characterized with TPR, reflective UV/Visible spectroscopy and TEM. The best hydrogen production rate obtained for this setup for N/Ti = 10, 0.05 wt% Pt/N‐TiO₂, through water splitting was about 772 μmolh^?1g^?1.     

Fullerol–Titania Charge‐Transfer‐Mediated Photocatalysis Working under Visible Light

The development of visible‐light‐active photocatalysts is being investigated through various approaches. In this study, C₆₀‐based sensitized photocatalysis that works through the charge transfer (CT) mechanism is proposed and tested as a new approach. By employing the water‐soluble fullerol (C₆₀(OH)_x) instead of C₆₀, we demonstrate that the adsorbed fullerol activates TiO₂ under visible‐light irradiation through the “surface–complex CT” mechanism, which is largely absent in the C₆₀/TiO₂ system. Although fullerene and its derivatives have often been utilized in TiO₂‐based photochemical conversion systems as an electron transfer relay, their successful photocatalytic application as a visible‐light sensitizer of TiO₂ is not well established. Fullerol/TiO₂ exhibits marked visible photocatalytic activity not only for the redox conversion of 4‐chlorophenol, I^?, and Cr^VI, but also for H₂ production. The photoelectrode of fullerol/TiO₂ also generates an enhanced anodic photocurrent under visible light as compared with the electrodes of bare TiO₂ and C₆₀/TiO₂, which confirms that the visible‐light‐induced electron transfer from fullerol to TiO₂ is particularly enhanced. The surface complexation of fullerol/TiO₂ induced a visible absorption band around 400–500 nm, which was extinguished when the adsorption of fullerol was inhibited by fluorination of the surface of TiO₂. The transient absorption spectroscopic measurement gave an absorption spectrum ascribed to fullerol radical cations (fullerol^.+) the generation of which should be accompanied by the proposed CT. The theoretical calculation regarding the absorption spectra for the (TiO₂ cluster+fullerol) model also confirmed the proposed CT, which involves excitation from HOMO (fullerol) to LUMO (TiO₂ cluster) as the origin of the visible‐light absorption.     

Tricyclometalated Iridium Complexes as Highly Stable Photosensitizers for Light‐Induced Hydrogen Evolution

The development of an efficient and stable artificial photosensitizer for visible‐light‐driven hydrogen production is highly desirable. Herein, a new series of charge‐neutral, heteroleptic tricyclometalated iridium(III) complexes, [Ir(thpy)₂(bt)] ( 1 – 4 ; thpy=2,2′‐thienylpyridine, bt=2‐phenylbenzothiazole and its derivatives), were systematically synthesized and their structural, photophysical, and electrochemical properties were established. Three solid‐state structures were studied by X‐ray crystallographic analysis. This design offers the unique opportunity to drive the metal‐to‐ligand charge‐transfer (MLCT) band to longer wavelengths for these iridium complexes. We describe new molecular platforms that are based on these neutral iridium complexes for the production of hydrogen through visible‐light‐induced photocatalysis over an extended period of time in the presence of [Co(bpy)₃]²⁺ and triethanolamine (TEOA). The maximum amount of hydrogen was obtained under constant irradiation over 72 h and the system could regenerate its activity upon the addition of cobalt‐based catalysts when hydrogen evolution ceased. Our results demonstrated that the dissociation of the [Co(bpy)₃]²⁺ catalyst contributed to the loss of catalytic activity and limited the long‐term catalytic performance of the systems. The properties of the neutral complexes are compared in detail to those of two known non‐neutral bpy‐type complexes, [Ir(thpy)₂(dtb‐bpy)]⁺ ( 5 ) and [Ir(ppy)₂(dtb‐bpy)]⁺ ( 6 ; ppy=2‐phenylpyridine, dtb‐bpy=4,4′‐di‐tert‐butyl‐2,2′‐dipyridyl). This work is expected to contribute toward the development of long‐lasting solar hydrogen‐production systems.     

Molten Ag2SO4‐based Ion‐Exchange Preparation of Ag0.5La0.5TiO3 for Photocatalytic O2 Evolution

Ag_0.5La_0.5TiO₃ with an ABO₃ perovskite structure was synthesized by a newly developed ion‐exchange method. Molten Ag₂SO₄ instead of traditional molten AgNO₃ was used as Ag⁺ source in view of its high decomposition temperature (1052 °C), thereby guaranteeing the complete substitution of Ag⁺ for Na⁺ in Na_0.5La_0.5TiO₃ with a stable ABO₃ perovskite structure at a high ion‐exchange temperature (700 °C). Under full‐arc irradiation, the O₂‐evolution activity of Ag_0.5La_0.5TiO₃ was about 1.6 times that of Na_0.5La_0.5TiO₃ due to the optimized electronic band structures and local lattice structures. On the one hand, the substitution of Ag⁺ for Na⁺ elevated the VBM and thus narrowed the band gap from 3.19 to 2.83 eV, thereby extending the light‐response range and, accordingly, enhancing the photoexcitation to generate more charge carriers. On the other hand, the substitution of Ag⁺ for Na⁺ induced a lattice distortion of the ABO₃ perovskite structure, thereby promoting the separation and migration of charge carriers. Moreover, under visible‐light irradiation, Ag_0.5La_0.5TiO₃ displayed notable O₂ evolution whereas Na_0.5La_0.5TiO₃ showed little O₂ evolution, thus demonstrating that the substitution of Ag⁺ for Na⁺ enabled the use of visible light to evolve O₂ photocatalytically. This work presents an effective route to explore novel Ag‐based photocatalysts.     

Hot π‐Electron Tunneling of Metal–Insulator–COF Nanostructures for Efficient Hydrogen Production

A metal–insulator–semiconductor (MIS) photosystem based on covalent organic framework (COF) semiconductors was designed for robust and efficient hydrogen evolution under visible‐light irradiation. A maximal H₂ evolution rate of 8.42 mmol h^?1 g^?1 and a turnover frequency of 789.5 h^?1 were achieved by using a MIS photosystem prepared by electrostatic self‐assembly of polyvinylpyrrolidone (PVP) insulator‐capped Pt nanoparticles (NPs) with the hydrophilic imine‐linked TP‐COFs having =C=O?H?N= hydrogen‐bonding groups. The hot π‐electrons in the photoexcited n‐type TP‐COF semiconductors can be efficiently extracted and tunneled to Pt NPs across an ultrathin PVP insulating layer to reduce protons to H₂. Compared to the Schottky‐type counterparts, the COF‐based MIS photosystems give a 32‐fold‐enhanced carrier efficiency, attributed to the combined enhancement of photoexcitation rate, charge separation, and oxidation rate of holes accumulated in the valence band of the TP‐COF semiconductor.     

A Methylthio‐Functionalized‐MOF Photocatalyst with High Performance for Visible‐Light‐Driven H2 Evolution

Recently, the emergence of photoactive metal–organic frameworks (MOFs) has given great prospects for their applications as photocatalytic materials in visible‐light‐driven hydrogen evolution. Herein, a highly photoactive visible‐light‐driven material for H₂ evolution was prepared by introducing methylthio terephthalate into a MOF lattice via solvent‐assisted ligand‐exchange method. Accordingly, a first methylthio‐functionalized porous MOF decorated with Pt co‐catalyst for efficient photocatalytic H₂ evolution was achieved, which exhibited a high quantum yield (8.90 %) at 420 nm by use sacrificial triethanolamine. This hybrid material exhibited perfect H₂ production rate as high as 3814.0 μmol g^?1 h^?1, which even is one order of magnitude higher than that of the state‐of‐the‐art Pt/MOF photocatalyst derived from aminoterephthalate.     

A Hydrogen‐Deficient Nickel–Cobalt Double Hydroxide for Photocatalytic Overall Water Splitting

Developing highly efficient and low‐cost photocatalysts for overall water splitting has long been a pursuit for converting solar power into clean hydrogen energy. Herein, we demonstrate that a nonstoichiometric nickel–cobalt double hydroxide can achieve overall water splitting by itself upon solar light irradiation, avoiding the consumption of noble‐metal co‐catalysts. We employed an intensive laser to ablate a NiCo alloy target immersed in alkaline solution, and produced so‐called L‐NiCo nanosheets with a nonstoichiometric composition and O^2?/Co³⁺ ions exposed on the surface. The nonstoichiometric composition broadens the band gap, while O^2? and Co³⁺ ions boost hydrogen and oxygen evolution, respectively. As such, the photocatalyst achieves a H₂ evolution rate of 1.7 μmol h^?1 under AM 1.5G sunlight irradiation and an apparent quantum yield (AQE) of 1.38 % at 380 nm.     

Constructing SrTiO3–TiO2 Heterogeneous Hollow Multi‐shelled Structures for Enhanced Solar Water Splitting

Constructing hollow multi‐shelled structures (HoMSs) has a significant effect on promoting light absorption property of catalysts and enhancing their performance in solar energy conversion applications. A facile hydrothermal method is used to design the SrTiO₃?TiO₂ heterogeneous HoMSs by hydrothermal crystallization of SrTiO₃ on the surface of the TiO₂ HoMSs, which will realize a full coverage of SrTiO₃ on the TiO₂ surface and construct the SrTiO₃/TiO₂ junctions. The broccoli‐like SrTiO₃?TiO₂ heterogeneous HoMSs exhibited a fourfold higher overall water splitting performance of 10.6 μmol h^?1 for H₂ production and 5.1 μmol h^?1 for O₂ evolution than that of SrTiO₃ nanoparticles and the apparent quantum efficiency (AQE) of 8.6 % at 365 nm, which can be mainly attributed to 1) HoMS increased the light absorption ability of the constructed photocatalysts and 2) the SrTiO₃?TiO₂ junctions boosted the separation efficiency of the photogenerated charge carriers.