GC-MS/FID测定环境空气中57种臭氧前体物

建立了GC-MS/FID测定环境空气中57种臭氧前体物的分析方法.优化三级冷阱捕集温度、三级冷阱解析温度、初始柱温、毛细管色谱柱等实验条件.优化条件为:采用硅烷化的苏玛罐采集环境空气,目标组分经三级冷阱在-180℃低温浓缩富集,80℃解析,初始柱温为15℃,结合中心切割技术,将乙烷、乙烯、乙炔、丙烷、丙烯切割至TG-B...     

Adsorptive Separation of Acetylene from Light Hydrocarbons by Mesoporous Iron Trimesate MIL‐100(Fe)

A reducible metal–organic framework (MOF), iron(III) trimesate, denoted as MIL‐100(Fe), was investigated for the separation and purification of methane/ethane/ethylene/acetylene and an acetylene/CO₂ mixtures by using sorption isotherms, breakthrough experiments, ideal adsorbed solution theory (IAST) calculations, and IR spectroscopic analysis. The MIL‐100(Fe) showed high adsorption selectivity not only for acetylene and ethylene over methane and ethane, but also for acetylene over CO₂. The separation and purification of acetylene over ethylene was also possible for MIL‐100(Fe) activated at 423 K. According to the data obtained from operando IR spectroscopy, the unsaturated Fe^III sites and surface OH groups are mainly responsible for the successful separation of the acetylene/ethylene mixture, whereas the unsaturated Fe^II sites have a detrimental effect on both separation and purification. The potential of MIL‐100(Fe) for the separation of a mixture of C₂H₂/CO₂ was also examined by using the IAST calculations and transient breakthrough simulations. Comparing the IAST selectivity calculations of C₂H₂/CO₂ for four MOFs selected from the literature, the selectivity with MIL‐100(Fe) was higher than those of CuBTC, ZJU‐60a, and PCP‐33, but lower than that of HOF‐3.     

Cu Single-Atom Catalysts for High-Selectivity Electrocatalytic Acetylene Semihydrogenation

The site isolation strategy has been employed in thermal catalytic acetylene semihydrogenation to inhibit overhydrogenation and C−C coupling. However, there is a dearth of analogous investigations in electrocatalytic systems. In this work, density functional theory (DFT) simulations demonstrate that isolated Cu metal sites have higher energy barriers on overhydrogenation and C−C coupling. Following this result, we develop Cu single-atom catalysts highly dispersed on nitrogen-doped carbon matrix, which exhibit high ethylene selectivity (>80 % Faradaic efficiency for ethylene, <1 % Faradaic efficiency for C₄, and no ethane) at high concentrations of acetylene. The superior performance observed in the electrocatalytic selective hydrogenation of acetylene can be attributed to the weak adsorption of ethylene intermediates and highly energy barriers on C−C coupling at isolated sites, as confirmed by both DFT calculations and experimental results. This study provides a comprehensive understanding of the isolated sites inhibiting the side reactions of electrocatalytic acetylene semihydrogenation.     

Evaluation of a dual-sorbent trap for monitoring organic compounds in air.

The performance of a new kind of multi-sorbent trap for use in the simultaneous determination of compounds of different volatility and polarity was investigated. The adsorbents employed for this purpose were Carbograph 2 and Carbograph 5. The performance of this trap was evaluated in terms of thermal desorption and solvent extraction recoveries of substances belonging to the main classes of organic compounds, at different amounts and volumes of air sampled corresponding to concentrations ranging from 0.1 to 1000 mg/m3. The tubes examined allowed the trapping of the compounds used and their complete desorption with the procedure best suited to the analytical problem.     

Multisorbent tubes sampling used in thermal desorption cold trap injection with gas chromatography-mass spectrometry for C2–C6 hydrocarbon measurements in an urban atmosphere

Three solid adsorbents (Carbotrap, Carbotrap C, and Carbosieve III) were evaluated for sampling trace non-methane hydrocarbons in urban atmospheres. The sampled atmosphere was pumped through a multisorbent tube containing the three sorbents separated by a small amount of silanized glass wool. The trapped compounds were recovered by thermal desorption and analysed by combining cryogenic enrichment with gas chromatography and mass spectrometry. Adsorption/thermal desorption and breakthrough experiments were performed to test their ability to quantitatively trap the light hydrocarbons. The technique was suitable for determination of low ppbv concentrations of these compounds. Ambient atmospheric sampling was conducted in Vitoria-Gasteiz (Basque Country, Spain), and the measurements cover a period of one year (2001–2002). Fifteen C₂–C₆ hydrocarbons are identified and quantified, and seasonal trends are discussed.     

Application of a unique selective PLOT capillary column for the analysis of oxygenated compounds in ambient air

Summary A new PLOT column (CP-LOWOX) designed specifically for the analysis of oxygenated compounds has been used for the gas chromatographic determination of semi-volatile carbonyl compounds. The separation behavior of the new column was investigated by comparing it with the widely used non-polar polydimethylsiloxane and polar poly(ethylene glycol) columns. The CP-LOWOX column has unique selectivity for aldehydes and ketones enabling a selective separation of these analytes from predominating hydrocarbon matrices. Application of the CP-LOWOX column for the analysis of polar compounds in ambient air is demonstrated. Sampling was performed by adsorptive enrichment coupled with thermal desorption. The suitability of Tenax TA and a multi-bed adsorbent trap Carbotrap C and Carbotrap) was tested for the sampling of semivolatile carbonyl compounds. Presented at Balaton Symposium on High Performance Separation Methods, Siófok, Hungary, September 1–3, 1999     

Stability of workroom air volatile organic compounds on solid adsorbents for thermal desorption gas chromatography

The storage stability of the occupationally frequently occurring compounds, methylethylketone, methylisobutylketone, benzene, toluene, tetrachloroethylene, n-butylacetate, -pinene, β-pinene, limonene and n-decane, has been investigated on the adsorbents Tenax TA, Chromosorb 106 and Carbotrap using thermally desorbable tube type samplers, commonly utilized in ambient and workroom atmospheric measurements. Fifty and 500 ng of each compound were loaded on the various adsorbents tubes, stored at both ambient (20 °C) and refrigerated (4 °C) temperatures and analysed by means of thermal gas chromatography with mass spectrometric detection on days 0, 7, 14 and 28 after exposure. A 90% storage recovery was chosen as acceptance criteria for storage stability, and statistical testing by Student's t-test, analysis of variance and Bonferroni post hoc tests were employed to investigate the effect of the categorical variables storage time, storage temperature and analyte loading on the different adsorbents. Chromosorb 106 showed the overall best behaviour with recoveries of 90% or better for all analytes during the 28-day test period. Tenax TA and Carbotrap yielded lower recoveries and were more influenced by variations in storage time, storage temperature and analyte loading. Refrigerated temperatures were best avoided for storage on Tenax TA, but may increase the recovery of some compounds on Carbotrap (e.g. n-butylacetate). The blank build-up on the adsorbents was also investigated, and Carbotrap and Tenax TA showed no signs of artefact development over time. Chromosorb 106, however, contained inherently more artefacts that build up over time, which in spite of the excellent storage capability, may limit its use in field studies where long storage times are normal.     

Activation of Pd-Ag Catalyst for Selective Hydrogenation of Acetylene via Nitrous Oxide Addition

Hydrogenation of acetylene in the presence of a large excess of ethylene has been investigated on the Pd-Ag catalyst under 60°C and a space velocity of 2,000 h^–1. It was found that an enhancement in the performance of Pd-Ag catalyst can be obtained by pretreatment with N₂O. It is suggested that added N₂O on the catalyst before use not only augments the sites associated with ethylene production from acetylene but also depletes the sites responsible for direct ethane formation.     

The conversion of natural gas to higher hydrocarbons using a microwave plasma and catalysts

Methane, the major constituent of natural gas, had been converted to higher hydrocarbons by a microwave plasma. The yield of C2+ products increased from 29.2% to 42.2% with increasing the plasma power and decreasing the flow rate of methane. When the catalysts were used in the plasma reactor, the selectivities of ethylene and acetylene increased while the yield of C2+ remained constant. Among the various catalysts used, the Fe catalyst showed the highest ethylene selectivity of 30%. When we introduced the actual natural gas, more C2+ products were obtained (46%). This is due to the ethane and propane in the natural gas. When an electric field inductance for evolving the high plasma was applied, a high yield in C2+ products of 63.7% was obtained for the Pd-Ni bimetal catalyst.     

Copolymerization of acetylene with ethylene in the presence of dibenzenetitanium(0)

The interaction between acetylene and dibenzenetitanium(0) at a room temperature results in the acetylene polymerization and its reduction to ethylene, ethane, and methane at the expense of H atoms of the acetylene molecule. The catalytically active species capable of copolymerizing acetylene with ethylene that are formed during the reaction or are added into the system originate from the interaction of dibenzenetitanium(0) with acetylene.     

微波等离子体下一氧化碳氢化制乙炔反应中产物的选择性研究(英文)

采用微波等离子体技术研究了一氧化碳氢化制乙炔反应的产物选择性。对影响乙炔选择性的几个因素,如微波输入功率、反应物的比例和体系压力进行了研究。乙炔的选择性随着微波输入功率的增加,反应物比例和体系压力的降低而增大。在最佳条件下,乙炔的选择性可达到９５．８７％,甲烷选择性的变化规律和乙炔相反,乙烯和乙烷的选择性很低。等离子体中的电子温度（或能量）和密度采用了静电悬浮双探针诊断,电子密度和能量受微波输入功率和体系压力的影响。在反应中,电子能量决定化学反应是否进行,电子密度决定产物的组成。根据自由基反应理论解释了乙炔选择性在Ｈ２＋ＣＯ等离子体化学反应中随影响因素的变化规律。     

Oxygen species on NiO/Al2O3 and their reactivities

Oxygen species on fresh and treated NiO/Al₂O₃ and their activities for oxidation of ethane and ethylene were investigated using catalytic property measurements, ethane and ethylene pulse experiments and O₂–TPD–MS experiments. The results revealed that there are two kinds of active oxygen species (the more active one and the less active one) on fresh NiO/Al₂O₃ catalyst, but there is only one active oxygen species, the less active one, on treated NiO/Al₂O₃ catalyst. The more active oxygen species can convert ethane or ethylene to carbon dioxide by one step while the less active one can only convert ethane to ethylene, but cannot convert ethane and/or ethylene to carbon dioxide. The more active oxygen species can be removed from the catalyst by heating from 350 to 850 °C. The amounts of desorption oxygen on the catalysts are proportional to their selectivity to carbon dioxide.     

Formation of C4 Oligomers in Hydrogenation of Acetylene over Pd/Al2O3 and Pd/TiO2 Catalysts

Selectivity of product formation has been tested in hydrogenation of acetylene over 0.3 wt.% Pd/-alumina and 0.5 wt.% Pd/TiO₂catalysts. Non-steady-state regime of catalyst operation was tested in pulse-flow experiments. Significant carbon poisoning appears to be a necessaryrequisite for selective formation of ethylene. The effect of hydrogen and acetylene partial pressure has been tested on the selectivity of C₄products. At 273–298 K the catalysts showed 26–35% selectivity for C₄ hydrocarbons and <2.5% for ethane production at conversionsof 30–40%. Deuterium distribution in ethylene and 1,3-butadiene and the deuterium content of the surface hydrogen pool have been compared and mechanismof diene formation has been discussed.     

The flash photolysis of azomethane. Minor products from the photolysis of methyl radicals and a rate constant for CH3 + NO

The flash photolysis of azomethane in a quartz reaction vessel produces mainly ethane (>75%) plus smaller quantities of methane, ethylene, and acetylene. The minor products are interpreted quantitatively in terms of methyl radical photolysis at 216 nm to give CH₂ and H. This interpretation is substantiated by the dependence of the minor products on flash intensity. The reduction of the ethane yield on adding NO is employed to obtain a rate constant for CH₃ + NO as a function of total pressure, based on a value for methyl radical recombination of 4.2 × 10^?11 cm³/molec · sec. An RRKM analysis is used to extrapolate the data to give a limiting high-pressure rate constant for CH₃ + NO of (1.2 ± 0.1) × 10^?11 cm³/molec · sec at 298°K.     

Measurement of non-methane hydrocarbons in Taipei city and their impact on ozone formation in relation to air quality

Air pollutants data from semi-continuous measurements at multiple sampling sites in Taipei metropolitan area of Taiwan was obtained by collecting air samples in canisters. The hydrocarbon composition was determined by using GC/MS and GC/FID. The air samples were pre-concentrated onto glass beads prior to separation by PLOT and DB-1 columns of GC. The method showed detection limit of <1 ppb and relative standard deviation in the range of 5-30% for different compounds. Aromatic hydrocarbons (toluene, benzene, etc.) and aliphatic hydrocarbons (ethylene, acetylene, propane, etc.) were correlated primarily to determine the source of emission. The estimated hydrocarbons were ranked according to their abundance and photochemical reactivity. The criteria pollutants, ozone and NO₂ were measured by UV-differential optical absorption spectroscopy (UV-DOAS), and were utilized to determine the relative importance of non-methane hydrocarbons (NMHC) and significant contribution of NO₂ in limiting ozone formation. The obtained results suggest that ozone formation in Taipei city is probably limited by the supply of non-methane hydrocarbons. The concentration profile of targeted pollutants was compared to other metropolitan areas to determine air quality and the pollutant sources.     

Activity and selectivity of Ni nanoclusters in the selective hydrogenation of acetylene: A computational investigation

In this work, the Ni_n (n = 2–10) nanoclusters were investigated to design new catalysts for the selective hydrogenation of acetylene. Our results show that among the Ni_n nanoclusters, the Ni₆ nanocluster can be used as a catalyst in the reactions of hydrogenation. In the presence of the Ni₆ nanocluster, the E_a of the forward step in the reaction of conversion of vinyl to ethylene was 21.21 kJ/mol lower than that of the reverse step in the reaction of conversion of acetylene to vinyl. Also, the E_a of the forward step in the reaction of conversion of ethyl to ethane was 96.59 kJ/mol higher than that of the reverse step in the reaction of conversion of ethylene to ethyl. According to the obtained results, the Ni₆ nanocluster can selectively act in the hydrogenation of a mixture of acetylene and ethylene.     

Effect of acetylene on the γ-radiation-induced polymerization of ethylene

The effects of acetylene on the γ-radiation-induced polymerization of ethylene were studied from the viewpoint of the gaseous products and polymer structure. The experiments were carried out under a pressure of 400 kg/cm²; the temperature was 30°C; the does rate was 1.1 × 10⁵ rad/hr; and the acetylene content was 0–20%. The solid polymer was obtained in the polymerization of ethylene containing 2.2% acetylene, while the monomer containing 19.7% acetylene gave a yellowish viscous oil. The polymer yield and molecular weight decreased remarkably with acetylene content. The main gaseous product was hydrogen, and trace amounts of butane, butene-1, butadiene-1,3, and benzene and its derivatives were also observed. The rate of formation of hydrogen was almost independent of acetylene content and there was no difference in acetylene contents before and after the irradiation was found. The infrared spectra of the polymers showed the presence of vinylidene, trans-vinylene, and terminal vinyl unsaturations, 1,4-disubstituted benzene, and carbonyl groups. The contents of trans-vinylene, terminal vinyl, and methyl groups increased with acetylene content, and that of vinylidene was independent of acetylene content. The monomer reactivity ratios of ethylene and acetylene were evaluated as 45.5 and 66.0, respectively. On the basis of the results, the effects of acetylene on the γ-radiation-induced polymerization of ethylene were discussed.     

Rapid analysis of dissolved methane, ethylene, acetylene and ethane using partition coefficients and headspace-gas chromatography

Analysis of dissolved methane, ethylene, acetylene, and ethane in water is crucial in evaluating anaerobic activity and investigating the sources of hydrocarbon contamination in aquatic environments. A rapid chromatographic method based on phase equilibrium between water and its headspace is developed for these analytes. The new method requires minimal sample preparation and no special apparatus except those associated with gas chromatography. Instead of Henry's Law used in similar previous studies, partition coefficients are used for the first time to calculate concentrations of dissolved hydrocarbon gases, which considerably simplifies the calculation involved. Partition coefficients are determined to be 128, 27.9, 1.28, and 96.3 at 30°C for methane, ethylene, acetylene, and ethane, respectively. It was discovered that the volume ratio of gas-to-liquid phase is critical to the accuracy of the measurements. The method performance can be readily improved by reducing the volume ratio of the two phases. Method validation shows less than 6% variation in accuracy and precision except at low levels of methane where interferences occur in ambient air. Method detection limits are determined to be in the low ng/L range for all analytes. The performance of the method is further tested using environmental samples collected from various sites in Nova Scotia.     

Application of thermal desorption to the development of a gas chromatographic/mass spectrometric method for the determination of toluene,chlorinated aromatic hydrocarbons,and 2,3,7,8-tetrachlorodibenzo-p-dioxin in combustion emissions

A fast and accurate analytical method, which uses commercially available adsorbents (Tenax TA, Carbotrap B and C, and Carbosieve S-III), was developed for the sampling and determination of aromatic hydrocarbons, chloroaromatic compounds, and 2,3,7,8-tetrachlorodibenzo-p-dioxin. The breakthrough volume data show that Carbotrap C has a good capacity for compounds of high molecular weight, whereas Carbosieve S-III and Tenax TA are efficient for volatile compounds. The organic components are thermally desorbed and transferred to a gas chromatograph/mass spectrometer. Importantly, thermal desorption avoids conventional solvent extraction procedures and also allows reuse of adsorbent tubes. Preliminary results for recovery of analytes from tubes packed with single adsorbent prove that a single-adsorbent bed is not capable of sampling a wide range of compounds. The best method to obtain the desired collection and desorption properties is to use adsorbent tubes containing several different materials. The results of optimization studies are summarized.