Poly(lactic acid)/Poly(3-hydroxybutyrate) Biocomposites with Differently Treated Cellulose Fibers

The growing concern about environmental pollution has generated an increased demand for biobased and biodegradable materials intended particularly for the packaging sector. Thus, this study focuses on the effect of two different cellulosic reinforcements and plasticized poly(3-hydroxybutyrate) (PHB) on the properties of poly(lactic acid) (PLA). The cellulose fibers containing lignin (CFw) were isolated from wood waste by mechanical treatment, while the ones without lignin (CF) were obtained from pure cellulose by acid hydrolysis. The biocomposites were prepared by means of a melt compounding-masterbatch technique for the better dispersion of additives. The effect of the presence or absence of lignin and of the size of the cellulosic fibers on the properties of PLA and PLA/PHB was emphasized by using in situ X-ray diffraction, polarized optical microscopy, atomic force microscopy, and mechanical and thermal analyses. An improvement of the mechanical properties of PLA and PLA/PHB was achieved in the presence of CF fibers due to their smaller size, while CFw fibers promoted an increased thermal stability of PLA/PHB, owing to the presence of lignin. The overall thermal and mechanical results show the great potential of using cheap cellulose fibers from wood waste to obtain PLA/PHB-based materials for packaging applications as an alternative to using fossil based materials. In addition, in situ X-ray diffraction analysis over a large temperature range has proven to be a useful technique to better understand changes in the crystal structure of complex biomaterials.     

Mechanical and thermal characterization of sisal fiber reinforced polylactic acid composites

The advantages of green composites are including, but not limited to their environmental friendly nature, lightweight, reduction of production energy and costs, and recyclability. This work focuses on the mechanical, thermal, and dynamic mechanical properties of biocomposites. For that purpose, biosourced polymers were used, namely polylactic acid (PLA) and sisal fiber, and biocomposites were extruded and then injection molded with different contents of sisal fibers (5%, 10%, 15%). The results show that the increase of the rate of reinforcement improves the mechanical and dynamic mechanical properties of the biocomposites made. By the increase of the sisal fiber content, the degree of crystallinity of the matrix was increased from 47% to 61%, as sisal fibers were acted as a nucleating agent for the PLA.     

Mechanical and biodegradation performance of short natural fibre polyhydroxybutyrate composites

The work outlined in this paper describes the evaluation of polyhydroxybutyrate (PHB) based natural fibre composites via an extrusion – injection moulding process. Virgin PHB was compounded with two different naturally occuring plant fibres, hemp and jute, and a third, regenerated cellulose fibre, lyocell. Composite materials containing 10–30 wt% of each type of fibre were obtained by twin screw extrusion and the resultant material was injection moulded to produce tensile samples suitable for mechanical characterisation. Mechanical properties were determined using tensile, impact and flexural testing. Melt flow index and water absorption studies were also carried out on the biocomposite materials, and Fourier transform infrared spectroscopy was used to examine the bonding between the polymer and each fibre type. The rate of biodegradation was also observed by placing composite samples in compost and measuring weight loss weekly. The biocomposites produced using this method were shown to have increased rates of biodegradation whilst exhibiting significantly improved flexural properties.     

Structure and properties of clay nano‐biocomposites based on poly(lactic acid) plasticized with polyadipates

The use of nano‐biocomposites based on plasticized poly(lactic acid) (PLA) has been proposed as a way to improve the polymer ductility and to expand PLA applications window. Novative nano‐biocomposites were elaborated with PLA plasticized by polyadipates (15 wt%) with different molar masses (from 1500 to 2500 Da), with 2.1 wt% of an organo‐modified montmorillonite (O‐MMT). These materials showed enhanced ductility and barrier properties. The clay was swelled in liquid polyadipates prior to their blending with PLA to facilitate chains intercalation and nanofiller exfoliation during melt‐blending. In certain processing conditions, quite homogenous and exfoliated structures were obtained, as shown by X‐ray diffraction (XRD) and transmission electronic microscopy (TEM) results. Irrespective of the average molar mass of the polyadipate, the clay addition induced a reduction in around 25% in oxygen transmission rate (OTR) without an important detriment in tensile properties. Nano‐biocomposites prepared with higher molar masses polyadipates showed the highest thermal stability as well as the lowest OTR, resulting in very promising and novative materials for different applications such as soft packaging. Copyright © 2010 John Wiley & Sons, Ltd.     

Thermal characterization and electrical properties of Fe-modified cellulose long fibers and micro crystalline cellulose

Thermal properties of polylactic acid (PLA) filled with Fe-modified cellulose long fibers (CLF) and microcrystalline cellulose (MCC) were studied using thermo gravimetric analysis (TG), differential scanning calorimetry, and dynamic mechanical analysis (DMA). The Fe-modified CLFs and MCCs were compared with unmodified samples to study the effect of modification with Fe on electrical conductivity. Results from TG showed that the degradation temperature was higher for all composites when compared to the pure PLA and that the PLA composites filled with unmodified celluloses resulted in the best thermal stability. No comparable difference was found in glass transition temperature (T _g) and melting temperature (T _m) between pure PLA and Fe-modified and unmodified CLF- and MCC-based PLA biocomposites. DMA results showed that the storage modulus in glassy state was increased for the biocomposites when compared to pure PLA. The results obtained from a femtostat showed that electrical conductivity of Fe-modified CLF and MCC samples were higher than that of unmodified samples, thus indicating that the prepared biocomposites have potential uses where conductive biopolymers are needed. These modified fibers can also be tailored for fiber orientation in a matrix when subjected to a magnetic field.     

Moisture Absorption Effects on the Mechanical Properties of Sandwich Biocomposites with Cork Core and Flax/PLA Face Sheets

The aim of this study was to evaluate the moisture absorption behaviour and its influence on the mechanical properties of newly developed sandwich biocomposites with flax fibre-reinforced poly-lactic acid (PLA) face sheets and soft cork as the core material. Three different types of sandwich biocomposite laminates comprised of different layup configurations, namely, non-woven flax/PLA (Sample A), non-woven flax/PLA and cork as core (Sample B) and non-woven flax/paper backing/PLA, cork as core (Sample C), were fabricated. In order to evaluate the influence of moisture ingress on the mechanical properties, the biocomposites were immersed in seawater for a period of 1200 h. The biocomposites (both dry and water immersed) were then subjected to tensile, flexural and low-velocity falling weight impact tests. It was observed from the experimental results that the moisture uptake significantly influenced the mechanical properties of the biocomposites. The presence of the cork and paper in sample C made it more susceptible to water absorption, reaching a value of 34.33%. The presence of cork in the core also has a considerable effect on the mechanical, as well as energy dissipation, behaviours. The results of sample A exhibited improved mechanical performance in both dry and wet conditions compared to samples B and C. Sample A exhibits 32.6% more tensile strength and 81.4% more flexural strength in dry conditions than that in sample C. The scanning electron microscopy (SEM) and X-ray micro-CT images revealed that the failure modes observed are a combination of matrix cracking, core crushing and face core debonding. The results from this study suggest that flax/PLA sandwich biocomposites can be used in various lightweight applications with improved environmental benefits.     

Grafting of cellulose by ring-opening polymerisation – A review

In this review, homogeneous and heterogeneous grafting from cellulose and cellulose derivatives by ring-opening polymerisation (ROP) are reported. Cellulose is biorenewable and biodegradable as well as a stiff material with a relatively low specific weight, foreseen to be an excellent replacement for synthetic materials. By utilising ROP of monomers such as ε-caprolactone or l-lactide from cellulose, composite materials with new and/or improved properties can be obtained. Grafting of solid cellulose substrates, such as cotton, microfibrillated cellulose (MFC) or cellulose nanocrystals, renders cellulose that can easily be dispersed into polymer matrices and may be used as reinforcing elements to improve mechanical and/or barrier properties of biocomposites. A surface grafted polymer can also tailor the interfacial properties between a matrix and the fibrillar structure of cellulose. When derivatives of cellulose are grafted with polymers in homogenous media, amphiphilic materials with interesting properties can be achieved, anticipated to be utilised for applications such as encapsulation and release.     

Silkworm silk/poly(lactic acid) biocomposites: Dynamic mechanical, thermal and biodegradable properties

Silkworm silk/Poly(lactic acid) (silk/PLA) biocomposites with potential for environmental engineering applications were prepared by using melting compound methods. By means of Dynamic mechanical analysis (DMA), Differential scanning calorimetry (DSC), Thermogravimetric analysis (TGA), Coefficient of thermal expansion test, Enzymatic degradation test and Scanning electron microscopy (SEM), the effect of silk fiber on the structural, thermal and dynamic mechanical properties and enzymatic degradation behavior of the PLA matrix was investigated. As silk fiber was incorporated into PLA matrix, the stiffness of the PLA matrix at higher temperature (70-160 °C) was remarkably enhanced and the dimension stability also was improved, but its thermal stability became poorer. Moreover, the presence of silk fibers also significantly enhanced the enzymatic degradation ability of the PLA matrix. The higher the silk fiber content, the more the weight loss.     

Effects of poly(ethylene glycol) on the morphology and properties of biocomposites based on polylactide and cellulose nanofibers

Polylactide (PLA)/cellulose nanofiber (CNF) biocomposites were prepared via solution casting and direct melt mixing. To improve the compatibility, a masterbatch of CNFs and poly(ethylene glycol) (PEG) (1:2) was also prepared. The effects of PEG on the morphology and properties of the biocomposites were investigated. The dispersion/distribution of nanofibers in PLA was improved when the masterbatch was used and the composites were prepared in solution. Substantial effects on the rheological properties of solution-prepared PLA/CNF/PEG composites were observed compared to composites containing no PEG, whereas for melt-prepared composites no significant changes were detected. Increased crystalline content and crystallization temperature were observed for the composites prepared via the masterbatch and solvent casting. The storage modulus of PLA was increased by 42 and 553% at 25 and at 80 °C, respectively, for the solution-based PEG-compatibilized composite containing 2 wt% nanofibers. Also, a better light transmittance was measured for the PLA/CNF/PEG composites prepared in solution.     

Effect of the Micronization of Pulp Fibers on the Properties of Green Composites

Green composites, composed of bio-based matrices and natural fibers, are a sustainable alternative for composites based on conventional thermoplastics and glass fibers. In this work, micronized bleached Eucalyptus kraft pulp (BEKP) fibers were used as reinforcement in biopolymeric matrices, namely poly(lactic acid) (PLA) and poly(hydroxybutyrate) (PHB). The influence of the load and aspect ratio of the mechanically treated microfibers on the morphology, water uptake, melt flowability, and mechanical and thermal properties of the green composites were investigated. Increasing fiber loads raised the tensile and flexural moduli as well as the tensile strength of the composites, while decreasing their elongation at the break and melt flow rate. The reduced aspect ratio of the micronized fibers (in the range from 11.0 to 28.9) improved their embedment in the matrices, particularly for PHB, leading to superior mechanical performance and lower water uptake when compared with the composites with non-micronized pulp fibers. The overall results show that micronization is a simple and sustainable alternative for conventional chemical treatments in the manufacturing of entirely bio-based composites.     

Topochemical acetylation of cellulose nanopaper structures for biocomposites: mechanisms for reduced water vapour sorption

Moisture sorption decreases dimensional stability and mechanical properties of polymer matrix biocomposites based on plant fibers. Cellulose nanofiber reinforcement may offer advantages in this respect. Here, wood-based nanofibrillated cellulose (NFC) and bacterial cellulose (BC) nanopaper structures, with different specific surface area (SSA), ranging from 0.03 to 173.3 m²/g, were topochemically acetylated and characterized by ATR-FTIR, XRD, solid-state CP/MAS ¹³C-NMR and moisture sorption studies. Polymer matrix nanocomposites based on NFC were also prepared as demonstrators. The surface degree of substitution (surface-DS) of the acetylated cellulose nanofibers is a key parameter, which increased with increasing SSA. Successful topochemical acetylation was confirmed and significantly reduced the moisture sorption in nanopaper structures, especially at RH = 53 %. BC nanopaper sorbed less moisture than the NFC counterpart, and mechanisms are discussed. Topochemical NFC nanopaper acetylation can be used to prepare moisture-stable nanocellulose biocomposites.     

The influence of pre-treatment of Spartium junceum L. fibres on the structure and mechanical properties of PLA biocomposites

Different chemical pre-treatments of Spartium junceum L. fibres using alkali (NaOH), nanoclay (MMT) and Citric acid (CA) with the aim of producing biodegradable composite material are discussed. As environmental requirements in processing technologies have been higher in recent years, the Polylactic acid (PLA) is used in this research as a matrix, due to its renewability, biodegradability and biocompatibility. Biocomposites are prepared by reinforcing PLA with randomly oriented, short Spartium junceum L. fibres in order to increase material strength. The effects of different pre-treatments of Spartium junceum L. fibres on the mechanical properties of final biocomposite material are examined. Fibre tenacity is studied using Vibroscop and Vibrodyn devices. Tensile strength of biocomposite material was measured on the universal electromechanical testing machine Instron 5584. The results indicate that biocomposites reinforced with fibres modified with MMT and CA show upgraded mechanical properties of the final composite material in comparison with the composite materials reinforced with referenced (nontreated) fibres. Infrared spectra of tested fibres and biocomposites were determined with Fourier transform infrared spectroscopy using Attenuated total reflection (FT-IR ATR) sampling technique and the influence of fibre modifications on the fibre/polymer interfacial bonding was investigated. The interface of Spartium/PLA composites was observed with scanning electron microscope (SEM) and it was clearly visible that biocomposites reinforced with fibres modified by MMT and CA showed better interaction of fibres and matrix.     

Extraction and characterization of new cellulosic fibers from Indian mallow stem: An exploratory investigation

Natural fibers are one of the good alternative sources for replacing synthetic fiber and reinforcing polymer matrices because of their eco-friendly nature. This investigation deals with the extraction and characterization of new natural fiber from Indian mallow plant stem. The physico-chemical, thermal, and mechanical properties of Indian mallow fibers (IMFs) were reported and compared with other natural fibers for the first time. Cellulose (78.22%), wax (0.47%), density (1.33 g/cm³), and tensile strength (979.83 MPa) were recognized in IMFs. Fourier transform-infrared spectroscopy, X-ray diffraction, and thermo-gravimetric analysis confirmed that IMFs are rich in cellulose content and thermally stable with a crystallinity index of 72%.     

Development and thermal behaviour of ternary PLA matrix composites

Biodegradable PLA composites were prepared using microcrystalline cellulose (MCC) and silver (Ag) nanoparticles. The main objective of the present study is to develop new biopolymer composites with good mechanical properties, thermal stability, maintaining the optical transparency and also providing antimicrobial properties through silver nanoparticle introduction. Composites were prepared with 1%wt of Ag nanoparticles and 5%wt of MCC using a twin-screw microextruder; film parameters were optimized in order to obtain a thickness range between 20 and 60 μm.PLA composites maintained optical transparency properties of the matrix, while MCC was able to reduce polymer permeability. Thermal analysis revealed that MCC increased PLA crystallinity and the mechanical properties of the composites demonstrated that tensile modulus was improved by microcrystalline cellulose.     

Flame retardant poly (lactic acid) biocomposites based on azo‐boron coupled 4,4′‐sulfonyldiphenol and its combination with calcium lignosulfonate—Crystalline and mechanical properties

Poly (lactic acid) (PLA) has become an important biopolymer with excellent properties but has limited engineering applications where fire safety is ultimate. An efficient flame retardant (FR) for PLA biocomposites based on azo‐boron coupled with 4,4′‐sulfonyldiphenol‐(((1E,1′E)‐(sulfonylbis(6‐hydroxy‐3,1‐phenylene))bis (diazene‐2,1‐diyl))bis(3,1‐phenylene))diboronic acid (SBDA) was synthesized and characterized by FTIR, ¹H and ¹³C NMR spectra. SBDA was combined with calcium lignosulfonate (Calig) and compounded with PLA, and the FR, crystallization, and mechanical properties were investigated. The addition of 15 wt% FR (10 wt% Calig and 5 wt% SBDA) into PLA led to important reductions in peak heat release rate (PHRR) approximately 54%, total heat release (THR) approximately 28.6%, and the average effective heat of combustion (AEHC) approximately 29.4%. The fire performance index and fire growth index improved by approximately 56.4% and 33.1%, respectively. A V‐0 rating (vertical burning test) and a limiting oxygen index value of 28.8% were achieved for the FR PLA biocomposites. The combinatory SBDA/Calig reduced the segmental mobility of PLA in the organic‐inorganic interface with insignificant changes in the elongation at break and the Young Modulus. TG‐IR study showed significant reductions in pyrolysis gaseous products for the composites compared with PLA. This research work will expand the frontiers of knowledge on use of boron and calcium functionalized polyaromatic polyols for reducing the flammability of PLA.     

Investigation of cross-linked PVA/starch biocomposites reinforced by cellulose nanofibrils isolated from aspen wood sawdust

In this study, a bio-based composite prepared from cross-linked polyvinyl alcohol/starch/cellulose nanofibril (CNF) was developed for film packaging applications. For this purpose, CNF, as reinforcing phase, was initially isolated from aspen wood sawdust (AWS) using chemo-mechanical treatments, and during these treatments, hydrolysis conditions were optimized by experimental design. Morphological and chemical characterizations of AWS fibers were studied by transmission electron microscopy, scanning electron microscopy, Kappa number, and attenuated total reflectance-Fourier transform infrared spectroscopy, as well as National Renewable Energy Laboratory and ASTM procedures. Morphological images showed that the diameter of the AWS fibers was dramatically decreased during the chemo-mechanical treatments, proving the successful isolation of CNF. Moreover, chemical composition results indicated the successful isolation of cellulose, and Kappa number analysis demonstrated a dramatic reduction in lignin content. Mechanical, morphological, biodegradability, and barrier properties of biocomposites were also investigated to find out the influence of CNF on the prepared biocomposite properties. The mechanical results obtained from tensile analysis revealed that Young’s modulus and ultimate tensile strength of biocomposite films were enhanced with increasing CNF concentration, while a significant decrease was observed in elongation at break at the same concentration of CNF. Furthermore, with adding CNF, barrier properties and resistance to biodegradability were increased in films, whereas film transparency gradually declined.     

Influence of chemical surface modification of cellulose nanowhiskers on thermal,mechanical, and barrier properties of poly(lactide) based bionanocomposites

In the aim of producing fully organic bionanocomposite based on poly(lactide) (PLA), cellulose nanowhiskers (CNW) were grafted by n-octadecyl-isocyanate (CNW-ICN) applying an in situ surface grafting method. The compatibilizing effect of the long aliphatic grafted chain was investigated by thermal, mechanical and permeability analysis of solvent cast nanocomposite films. The grafted CNW-ICN could be successfully dispersed in the polymer matrix. The gained compatibility brought about a nucleating effect, decreasing the half time of isothermal crystallization from 25 min for the neat PLA to 8.4 min for the nanocomposite including 2.5 wt% CNW-ICN, e.g., tensile strength was improved by 10 MPa for the same 2.5 wt% CNW-ICN/PLA composite. Mechanical reinforcement was also effective in the rubbery state of PLA and increased the tensile modulus of the rubbery plateau providing thereby thermal resistance to the polymer. Oxygen barrier properties did not change significantly upon the inclusion of CNW-ICN, even when the quantity of CNW-ICN was increased to 15 wt%. More interestingly, the water vapour permeability of the CNW-ICN nanocomposite was always lower than the one of ungrafted CNW composites, which led to the conclusion that the hydrophobic surface graft and improved compatibility could counteract the effect of inclusion of hydrophilic structures in the matrix on water vapour transport. In conclusion, the surface grafting of CNW with isocyanates might be an easy and versatile tool for designing fully organic bionanocomposites with tailored properties.     

Preparation and Characterization of Modified Cellulose Fiber-Reinforced Polyvinyl Alcohol/Polypyrrolidone Hybrid Film Composites

In this work, cellulose was modified by using 2-(trifluromethyl)benzoylchloride by base catalyzed reaction. Modification of cellulose was confirmed by IR studies. The biodegradable composite films were developed by a film casting method using modified cellulose with poly(vinyl alcohol) and polypyrrolidone in different compositions. Film composites showed good biodegradability. Better barrier and mechanical properties showed by film composites as the percentage of modified cellulose increased. This indicates the importance of modified cellulose as a reinforcing agent. After analyzing these properties of film composites we came to the conclusion that, these biocomposites can be used for membrane and packaging applications.     

Extrusion,fiber formation,and characterization of thermotropic copolyesters

The flow behavior and the effect of the spinning conditions on the fiber properties and structure of poly(ethylene terephthalate) modified with 60 mol% p-hydroxybenzoic acid (PET/60PHB) were investigated. PET and its copolyesters with 28 and 80 mol% PHB were used as control samples. The melt of PET/60PHB at temperatures above 265°C exhibited extremely low viscosity and low flow activation energy. High birefringence, indicating the presence of a mesophase, was observed between 265 and 300°C on a hot-stage polarizing light microscope. The maximum tensile strength and initial modulus, 438 MPa and 37 GPa, respectively, were obtained at 275°C for a 0.69 IV polymer. The fiber strength and modulus were significantly lowered when extrusion was conducted at temperatures below 265°C. The fiber properties could also be improved when a high extrusion rate and/or a high draw down ratio was used. Scanning electron microscopy revealed that the fibers spun at temperatures above 265°C had a well-developed, highly oriented fibrillar structure. The fibers spun at lower temperatures, however, were poorly oriented and nonfibrillar in character. The high orientation and superior mechanical performance achieved at high temperatures were attributed to the presence of the nematic mesophase in the polymer melt.     

The Impact of Filler Geometry on Polylactic Acid-Based Sustainable Polymer Composites

Recently, biocomposites have emerged as materials of great interest to the scientists and industry around the globe. Among various polymers, polylactic acid (PLA) is a popular matrix material with high potential for advanced applications. Various particulate materials and nanoparticles have been used as the filler in PLA based matrix. One of the extensively studied filler is cellulose. However, cellulose fibres, due to their hydrophilic nature, are difficult to blend with a hydrophobic polymer matrix. This leads to agglomeration and creates voids, reducing the mechanical strength of the resulting composite. Moreover, the role of the various forms of pure cellulose and its particle shape factors has not been analyzed in most of the current literature. Therefore, in this work, materials of various shapes and shape factors were selected as fillers for the production of polymer composites using Polylactic acid as a matrix to fill this knowledge gap. In particular, pure cellulose fibres (three types with different elongation coefficient) and two mineral nanocomponents: precipitated calcium carbonate and montmorillonite were used. The composites were prepared by a melt blending process using two different levels of fillers: 5% and 30%. Then, the analysis of their thermomechanical and physico-chemical properties was carried out. The obtained results were presented graphically and discussed in terms of their shape and degree of filling.