Electronic structure and Fermi surface topology of the infinite-layered superconductor Sr1−xCaxCuO2

Superconductivity reported at 110 K, and recently at 150–170 K, in the infinite-layered (Sr_xCa_1−x)CuO₂ system is investigated by means of the full potential linear muffin-tin orbital (FLMTO) method. As in other high-T_c cuprates, the electronic structure of the parent compounds, CaCuO₂ and SrCuO₂, and of the separately calculated composition Sr_0.7Ca_0.3CuO₂ using the experimental lattice parameters, displays strong 2D features including a low density of states at E_F (lower than in the other cuprates) and a simple 2D Fermi surface (rounded square) with strong nesting due to a single hybridized Cu d-O p band. As in La₂CuO₄, a major van Hove saddle-point singularity exists near E_F. The drastic changes of the Fermi surface when Ca/Sr vacancies shift the Fermi energy to the van Hove singularity may have a strong influence on the superconducting properties of the compounds and indicate the need for Sr/Ca vacancies in inducing the high T_c.     

Unusual crystal structure of non-superconducting Y1Ba2Cu3O7−x films on buffered silicon substrates

Superconducting common c-axis oriented YBCO films as well as non-superconducting films epitaxially grown at significantly reduced substrate temperatures were deposited by laser ablation on CeO₂/YSZ buffered silicon substrates. The crystal structure of the non-superconducting films measured by XRD is collapsed from the original orthorhombic one, whereas the chemical composition detected using RBS and EDX remains identical. Especially the oxygen content in the non-superconducting material is as high as in the common 90 K superconductor. Thus, the change in the electrical behaviour is only due to a structural modification. The crystallographic model of a simple cubic YBCO perovskite unit cell does not represent completely our experimental results measured on the non-superconducting YBCO. A modified model based on detailed TEM and XRD measurements and known crystal defects of orthorhombic YBCO is proposed.     

Ramans study of Y1−xPrxBa2Cu3O7−δ and YB2Cu3−xZnxO7−δ single crystals

Single crystals with known T_c values of Y_1−xPr_xBa₂Cu₃O_7−δ (Y---Pr1:2:3) and YBa₂Cu_3−xZn_3−xZn_xO_7−δ (Y---Zn1:2:3) systems are studied by Raman measurements. The Raman spectra for (Y---Pr1:2:3) single crystals show that the frequencies of Ba and O_z modes increase as the Pr content increases. The results are consistent with the hole-localization scheme proposed for the suppression of superconductivity in the polycrystalline Y---Pr1:2:3 systems. On the other hand, in the Y---Zn1:2:3 system, all the Raman modes do not change in frequencies. However, the FWHM of the Cu(2) mode increases with the decrease of T_c, indicating strong scattering of charge carriers by the substituted Zn ions in the CuO₂ planes. The induced disorder in the CuO₂ planes may be related with suppression of T_c in the Y---Zn1:2:3 system. Thus, the suppression mechanism in the Y---Zn1:2:3 systems seems to be different from that in the Y---Pr1:2:3 systems.     

Phonon Raman scattering in Nd1+xBa2−xCu3O7−δ and Pr1+xBa2−xCu3O7−δ single crystals

The polarized Raman spectra of Nd_1+xBa_2−xCu₃O_7−δ (−0.023≤x≤0.107) and Pr_1+xBa_2−xCu₃O_7−δ (0.01≤x≤0.15) single crystals have been investigated. It was found that the Cu(2) A_g mode softens by 6 cm⁻¹ in Nd 1:2:3 and 4 cm⁻¹ in Pr 1:2:3 as x increases. These frequency shifts cannot be explained by the change in the relevant bond lengths due to Nd(Pr)-substitution for Ba. The variations with x of the two low frequency modes may be affected by change of their hybridization and/or change of their force constants. The linewidths of Ba mode in Pr 1:2:3 are broader than those in Y 1:2:3. This result suggests that the Pr substitution on Ba sites occurred even in a very small value of x. In x(yy) geometry the relative intensity of the Ba and O(4) modes in Nd 1:2:3 is greater than those in Pr 1:2:3. The difference between Nd 1:2:3 and Pr 1:2:3 in the relative intensity of the Ba and O(4) modes may be produced by the chains.     

Electrical and structural properties of epitaxially grown Y1Ba2Cu3O7 − x and Y2Ba4Cu8O16 − x thin films using the BaF2 method

Thin films of Cu, Y and BaF₂ are co-condensed in ultrahigh vacuum onto SrTiO₃ (1 0 0)-substrates at room temperature without any additional oxygen supply. It is found that the temperature of the ex situ fluorine-oxygen exchange reaction in flowing wet oxygen essentially determines whether the Y₁Ba₂Cu₃O_{7 − x}-phase (T_ex = 850°C) or the Y₂Ba₄Cu₈O_{16 − x}-phase (T_ex = 800°C) forms or any mixture of both phases in between. Small-angle X-ray diffraction verifies the strictly epitaxial growth of the superconducting phases. The variation of the composition around the ideal 1,2,3-stoichiometry affects only the superconducting and normal conducting properties which are measured using the four-probe Montgomery method. The values of the normal state resistivity and its temperature dependence are discussed in combination with a reduced cross section of the conduction paths in the films.     

Nax/2Bi1−x/2MoxV1−xO4 and Bi1−x/3MoxV1−xO4 New Scheelite-related phases

New Scheelite-related solid solutions of the compositions Na_x/2Bi_1−x/2Mo_xV_1−xO₄ (0≤x≤1) and Bi_1−x/3 Mo_xV_1−xO₄(0≤x≤0.2) have been synthesised by the substitution of Na and Mo at the A and B sites respectively of the ABO₄ type ferroelastic BiVO₄. The phases were characterised using chemical analysis, powder X-ray diffraction, scanning electron microscopy, EDAX, and Raman spectroscopy. While almost a continuous solid solution is obtained for the series Na_x/2Bi_1−x/2Mo_xV_1−xO₄, the absence of Na at the A-site results only in a narrow stability region for the other series, Bi_1−x/3 Mo_xV_1−xO₄ where 0≤x≤0.2. Raman spectra of selected samples at room temperature also suggest that vanadium and molybdenum atoms are disordered at the tetrahedral sites.     

Field induced flux pinning in Nd1+xBa2−xCu3O7−δ single crystal

The flux pinning behavior of a Nd_1+xBa_2−xCu₃O_7−δ (Nd123) single crystal, which exhibited a peak effect, has been studied by monitoring the time decay of the magnetic moment. The apparent pinning energy (U₀^*) was deduced from flux creep data on the basis of the Anderson-Kim model. The magnetic field dependence of U₀^* showed maxima at peak fields which depended on the temperatures, in a similar manner to those of critical current densities. In addition, the temperature dependence of U₀^* showed several features. To explain the increase in U₀^* with the field as well as its temperature and field dependence, we made a numerical calculation by introducing an additional pinning energy which increased with increasing field. The results are in good agreement with the experimental data, especially at temperatures above 60 K, where the contribution of field induced pinning centers is believed to be dominant.     

Hole formation and charge transfer in Y1−xCaxSr2Cu2GaO7, a new oxide superconductor

The technique of transmission electron energy loss spectrometry (EELS) in parallel detection has been utilized to analyze the fine structures associated with the O K and Cu L₃ absorption edges of recently discovered Y_1−xCa_xSr₂Cu₂GaO₇ (0.1 ≤ x ≤ 0.4) series of compounds, which exhibit superconductivity when annealed under high-pressure oxygen atmosphere. We find subtle but significant changes in EELS spectral features of nonsuperconducting and superconducting specimens of these compounds. A broad pre-edge feature is observed below the O K absorption edge, at about 528.2 eV which emerges with Ca-doping alone. Evidence is presented for another O K secondary pre-edge feature, at about 1.1 eV below the first O K pre-edge feature in only those specimens which have undergone high-pressure oxygen treatment (i.e. superconducting specimens). We interpret the O K pre-edge feature as due to formation of holes on oxygen sites and propose that the first broad pre-edge feature (at 528.2 eV) is associated with holes on oxygen sites other than the CuO₂ planes, which are responsible for normal conductivity. The second smaller pre-edge feature (at 527.1 eV) is most probably associated with holes in the CuO₂ planes, which are associated with superconductivity in this system. The presence of a secondary smaller O K pre-edge feature in the superconducting specimens appears to correlate well with a broad shoulder on the high energy side of the Cu L₃ edge. The results are interpreted in terms of oxidation of CuO₂ planes through charge transfer between copper and oxygen in the CuO₂ planes, i.e. covalent mixing of O and Cu orbitals at the Fermi level as a result of high oxygen pressure annealing.     

Synthesis, crystal structure and inelastic neutron scattering in the infinite-layer compounds Sr1−xNdxCuO2

For the first time large samples of the nominal composition Sr_1−xNd_xCuO₂ (x=0.07, 0.15) 10 g in mass each have been prepared using a high-pressure technique. Neutron-diffraction and X-ray measurements have shown that the main phase in the samples obtained is of the infinite-layer structure which has been refined in the tetragonal P4/mmm space group. Both samples are not superconducting. Inelastic neutron scattering has been employed to search for crystalline-electric-field transitions in these compounds. The observed low-energy spectra exhibit one inelastic line of magnetic origin at 18 meV, comparable in energy with a crystalline-electric-field excitation in the high-T_c superconductor NdBa₂Cu₃O_x.     

Oxide-ion conductivity of (Ba1−xLax)2In2O5+x system based on brownmillerite structure

(Ba_1−xLa_x)₂In₂O_5+x, whose end member is Ba₂In₂O₅, is an oxygen-deficient perovskite oxide showing high oxide-ion conductivity. In order to clarify the reason why the high oxide ion conductivity appeared in this system, the electrical conductivity was measured as a function of temperature and La content. With an increasing La content, the discontinuous jump of ion conductivity in the Arrhenius plot, which is related to the disordering of the oxygen vacancies, disappeared for the sample with x0.2. Above x=0.12, the ion conductivity linearly increased with La content, while the activation energy remained constant with respect to the La content. Moreover, the conductivity for x=0.6 was 0.042 (S/cm) at 1073 K, which exceeded that of 8 mol% yttria-stabilized zirconia. The higher oxide-ion conductivity of this system could be dominated by the amount of mobile oxygen ions.     

Structural characteristics and morphology of SmxCe1−xO2−x/2 thin films

Effect of the deposition temperature (200 and 500 °C) and composition of Sm_xCe_1−xO_2−x/2 (x = 0, 10.9–15.9 mol%) thin films prepared by electron beam physical vapor deposition (EB-PVD) and Ar⁺ ion beam assisted deposition (IBAD) combined with EB-PVD on structural characteristics and morphology/microstructure was investigated. The X-ray photoelectron spectroscopy (XPS) of the surface and electron probe microanalysis (EPMA) of the bulk of the film revealed the dominant occurrence of Ce⁴⁺ oxidation state, suggesting the presence of CeO₂ phase, which was confirmed by X-ray diffraction (XRD). The Ce³⁺ oxidation states corresponding to Ce₂O₃ phase were in minority. The XRD and scanning electron microscopy (SEM) showed the polycrystalline columnar structure and a rooftop morphology of the surface. Effects of the preparation conditions (temperature, composition, IBAD) on the lattice parameter, grain size, perfection of the columnar growth and its impact on the surface morphology are analyzed and discussed.     

Transient creep of YBa2Cu3O7−x superconductor

Rapid changes of oxygen partial pressure (P_O2) between 10³ and 2.1×10⁴ Pa have been carried out during steady-state plastic deformation of polycrystalline YBa₂Cu₃O_7−x (YBCO) at temperatures between 825 and 900°C. Transient creep was observed after such P_O2 changes. The analysis of these creep transients allowed the determination of the chemical diffusion coefficient for reequilibration, which is identical to that found from thermogravimetry and electrical conductivity experiments for oxygen vacancies.     

The structural features of Cu1−xPbx liquid alloys

Structure of Cu_1−xPb_x (x=0, 0.025, 0.05, 0.075, 0.1, 0.125) molten alloys has been studied by means of X-ray diffraction method. Structural parameters obtained from structure factors (SF) and radial distribution functions were analyzed. Partial structure factors were calculated by using Reverse Monte-Carlo method. It is shown that tendency to preferred interaction of atoms of the same kind grows with increasing of lead content.     

A 62 K superconductor with an original structure: Sr4−xBaxTlCu2CO3O7

A new superconductor with an original structure, Sr_4−xBa_xTlCu₂CO₃O₇ has been isolated for 1≤x≤2. It crystallizes in a A-type space group with a=3.84 Å≈a_p, b≈8 × a_p, c≈17.0 Å. The HREM study of this new curprate shows that it derives from the Tl_0.5Pb_0.5Sr₄Cu₂CO₃O₇ structure by a shearing mechanism. Indeed, it can be described as ribbons of the latter structure, four octahedra thick, shifted c/2 with respect to each other. It results in infinite single perovskite layers waving along the (001) plane and connected through flat mixed layers [(TIO)₄(CO)₄]∞. This oxycarbonate can also be described as a 1201-type structure in which the [TIO]∞ layers are replaced by mixed [(TIO)₄(CO)₄]∞ layers. The susceptibility measurements show that this cuprate exhibits a significantly higher critical temperature than the 1201-cuprates. The T_{c onset} of the synthesized phase is 56 K and it can be increased up to 62 K by hydrogen annealing; in the same way, one observes a large Meissner volume fraction of 35% at 4.2 K.     

Quantum critical point, scaling and universality in high Tc(CaxLa1−x)(Ba2−c−xLac+x)Cu3Oy

Using charge transport in sintered ceramic samples it is observed that at all doping, including non superconducting overdoped samples, there exists a temperature in which below it dR/dT < 0. This suggests that either the quantum critical point is not necessarily inside the superconducting dome or that the CuO₂ plane is never overdoped. Data relating experimental Cooper pair density, conductivity and T_c suggest that Homes’ relation might need a more specific definition of the conductivity σ.     

The relationship between crystal structure and electrical conductivity in the LaY1−xInxO3 (x=0.0–0.7) system

The electrical conductivity of the LaY_1−xIn_xO₃ (x=0.0–0.7) system has been studied from the viewpoint of crystal chemistry. The high temperature form of LaYO₃ (x=0.0) was ascertained to be the Sm₂O₃-type (B-type rare earth) structure, not perovskite-type one. The X-ray diffraction (XRD) experiments revealed that the samples with x=0.05 and 0.10 were the mixed phase of Sm₂O₃-type and perovskite-type structure, and changed to perovskite phase in the range of x0.20. From oxygen partial pressure dependence of the electrical conductivity, it was found that both the Sm₂O₃-type and the perovskite-type single phases showed hole conduction, but the mixed phase did oxide-ion one. The electrical conductivity of the LaY_1−xIn_xO₃ (x=0.0–0.7) system increased with increasing x, and showed the maximum value in the range of x=0.05–0.10, and then decreased with increasing x. The occurrence of oxide-ion conduction was discussed from the viewpoint of lattice distortion in the mixed phase.     

Structural and lithium intercalation studies of Mn(0.5−x)CaxTi2(PO4)3 phases (0≤x≤0.50)

Materials from the Mn_(0.5−x)Ca_xTi₂(PO₄)₃ (0≤x≤0.50) solid solution were obtained by solid-state reaction in air at 1000 °C. Selected compositions were investigated by powder X-ray diffraction analysis, ³¹P nuclear magnetic resonance (NMR) spectroscopy and electrochemical lithium intercalation. The structure of all samples determined by Rietveld analysis is of the Nasicon type with the R space group. Mn²⁺/Ca²⁺ ions occupy only the M1 sites in the Ti₂(PO₄)₃ framework. The divalent cations are ordered in one of two M1 sites, except for the Mn_0.50Ti₂(PO₄)₃ phase, where a small departure from the ideal order is observed by XRD and ³¹P MAS NMR. The electrochemical behaviour of Mn_0.50Ti₂(PO₄)₃ and Mn_(0.5−x)Ca_xTi₂(PO₄)₃ phases was characterised in Li cells. Two Li ions can be inserted without altering the Ti₂(PO₄)₃ framework. In the 0≤y≤2 range, the OCV curves of Li//Li_yMn_0.50Ti₂(PO₄)₃ cells show two main potential plateaus at 2.90 and 2.50–2.30 V. Comparison between the OCV curves of Li//Li_(1+y)Ti₂(PO₄)₃ and Li//Li_yMn_0.50Ti₂(PO₄)₃ shows that the intercalation occurs first in the unoccupied M1 site of Mn_0.50Ti₂(PO₄)₃ at 2.90 V and then, for compositions y>0.50, at the M2 site (2.50–2.30 V voltage range). The effect of calcium substitution in Mn_0.50Ti₂(PO₄)₃ on the lithium intercalation is also discussed from a structural and kinetic viewpoint. In all systems, the lithium intercalation is associated with a redistribution of the divalent cation over all M1 sites. In the case of Mn_0.50Ti₂(PO₄)₃, the stability of Mn²⁺ either in an octahedral or tetrahedral environment facilitates cationic migration.     

Estimation of conductivity parameters in Sr1 − xThxF2 + 2x solid solution with fluorite-type structure

Concentration of nn-dipoles, nnn-dipoles and charge carriers as well as parameters related to their reorientation and mobility have been estimated from an analysis of a.c. conductivity data of polycrystalline samples of the Sr_{1 − x}Th_xF_{2 + 2x} solid solution. The molar fraction of charge carriers has been evaluated as a function of composition. Results obtained confirm, in agreement with the clustering process model, that the (F_i)_m ions responsible for long range motions in Sr_{1 − x}Th_xF_{2 + 2x} are interstitial fluoride ions of F type.     

Synthesis and characterization of the Aurivillius phases Bi2 − xPbxSr1 − xNdxNb2O9

The n = 2 Aurivillius phase Bi_{2 − x}Pb_xSr_{1 − x}Nd₂O₉ was successfully synthesized as a ceramic material over the whole range of simultaneous, charge compensated substitution x = 0–1.0. Structural investigations were performed by Rietveld refinement applying different space groups Fmmm and A2₁am, and additionally by X-ray absorption spectroscopy (EXAFS) on the Nd L_III-edge, confirming the accommodation of Nd on the atomic sites of Sr, which implies the substitution of Bi³⁺ by the isoelectronic Pb²⁺. The ferroelectric transition temperature T_c = 270 °C of the substituted powders with x = 0.4 and 1.0 is distinctly reduced compared to the unsubstituted sample with T_c = 450 °C. In temperature resolved powder X-ray diffraction patterns no structural phase transition could be detected.     

Structural and vibrational properties of dilute GaNxAs1−x(P1−x)

We report a comprehensive analyzes of the Fourier transform infrared (FTIR) absorption and Raman scattering data on the structural and vibrational properties of dilute ternary GaAs_1−xN_x,[GaP_1−xN_x] (x<0.03) alloys grown on GaAs [GaP] by metal organic chemical vapor deposition (MOCVD) and solid source molecular beam epitaxy (MBE). By using realistic total energy and lattice dynamical calculations, the origin of experimentally observed N-induced vibrational features are characterized. Useful information is obtained about the structural stability, vibrational frequencies, lattice relaxations and compositional disorder in GaNAs (GaNP) alloys. At lower composition (x<0.015) most of the N atoms occupy the As [P] sublattice {N_As[N_P]}—they prefer moving out of their substitutional sites to more energetically favorable locations at higher x. Our results for the N-isotopic shifts of local mode frequencies compare favorably well with the existing FTIR data.