Hybrids of colloidal silica and waterborne polyurethane

Waterborne polyurethane (WPU) was synthesized and followed by adding colloidal silica to prepare WPU-silica hybrids. The silica content in the hybrid thin films was varied from 0 to 50 wt%. The experimental results revealed that the viscosity of these hybrid solutions increased with increasing silica content and resulted in the aggregation of silica particle in the hybrid films. The latter result was evidenced by SEM examination. The effect of interaction between silica particle and urethane polymer chains is more significant with increasing silica content. The prepared hybrid films show much better thermal stability and mechanical properties than pure WPU. The optical transparence did not linearly decrease with increasing the silica fraction in the hybrid thin film. At below 20% silica content, the film transparence decreased with increasing silica content; the converse is true at above 20% silica content. These results showed that the prepared hybrid films demonstrated tunable transparence with the silica fraction in the films.     

Preparation and Properties of Aramid-Silica Hybrids with Inter-Phase Bonding Through (3-glycidoxypropyl)-trimethoxysilane

Nano-composites from aramid-silica system have been prepared via sol-gel process. Poly (phenyleneterephthalamide) copolymer chains were prepared by reacting a mixture of p- and m-phenylenediamines with terephthaloyl chloride in dimethylacetamide used as solvent. The sol-gel process in the polymer matrix was carried out through hydrolysis and condensation of a mixture of tetraethoxysilane and (3-glycidoxypropyl) trimethoxysilane. The latter was used to develop linkage, on one hand with silica network structure using alkoxy groups and on the other hand with aramid chains at its secondary amine groups through glycidal groups of silane. Mutual interaction between the two disparate phases aramid and silica network was thus created. Thin films of the composites containing different proportions of silica ranging from 5.0 to 25.0-wt% were cast by the solvent elution technique. The α-relaxation temperature associated with the glass transition was measured by the dynamic mechanical thermal analysis. The results showed an increase in the glass transition temperature from 328°C for the pure aramid to 352°C for the hybrid materials containing 25-wt% silica, an indicative of the increased interfacial interaction between the two phases. Films having relatively low silica content were flexible and transparent, but those with high silica content were opaque and brittle. These films were tested for their tensile strength, modulus and toughness. The mechanical strength of the composites as compared to the pure aramid increased initially but with further addition of silica the strength decreased. The initial increase can be explained due to increased interfacial interaction between the two phases, however agglomeration of silica particles was responsible for decreasing strength at higher silica contents.     

Acrylic polymer/silica hybrids prepared by emulsifier‐free emulsion polymerization and the sol–gel process

Acrylic polymer/silica hybrids were prepared by emulsifier‐free emulsion polymerization and the sol–gel process. Acrylic polymer emulsions containing triethoxysilyl groups were synthesized by emulsifier‐free batch emulsion polymerization. The acrylic polymer/silica hybrid films prepared from the acrylic polymer emulsions and tetraethoxysilane (TEOS) were transparent and solvent‐resistant. Atomic force microscopy studies of the hybrid film surface suggested that the hybrid films did not contain large (e.g., micrometer‐size) silica particles, which could be formed because of the organic–inorganic phase separation. The Si? O? Si bond formed by the cocondensation of TEOS and the triethoxysilyl groups on the acrylic polymer increased the miscibility between the acrylic polymer component and the silica component in the hybrid films, in which the nanometer‐size silica domains (particles) were dispersed homogeneously in the acrylic polymer component. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 273–280, 2006     

Preparation and characterization of poly(phthalazinone ether ketone)/SiO<Subscript>2</Subscript> hybrid composite thin films with low friction coefficient

Organic–inorganic poly(phthalazinone ether ketone) (PPEK)/SiO₂ hybrid composite thin films were prepared by the dip-coating method on pre-cleaned glass substrates. The covalent bonds between organic and inorganic phases were introduced by an in-situ O-acylation reaction of isocyanatopropyltriethoxysilane (ICPTES) with the borohydride-reduced PPEK forming a polymer bearing triethoxysilyl groups. Theses groups were subsequently hydrolyzed with tetraethoxysilane (TEOS) and allowed to form a network via a sol–gel process. The polymer hybrid composite exhibited good thermal stability and a higher glass transition temperature as compared with the pure resin. Atomic force microscope, water contact angle measurement and scanning electron microscope were used to characterize the polymer hybrid thin films. The tribological experiment showed that the films have very low friction coefficient (about 0.1) and good anti-wear properties, without failure even after sliding for 18,000 s under modest loads. The improved tribological properties of the modified substrate were attributed to good adherence of PPEK/SiO₂ hybrid films on the substrate and synergy of both PPEK matrix and silica particles.     

接枝环氧树脂/硅溶胶杂化水分散液的制备与表征

利用原位分散法制备了接枝环氧树脂 硅溶胶杂化水分散液 ,并通过红外光谱和 ζ电位测定 ,表征了接枝环氧树脂与硅溶胶之间的杂化作用 .实验结果表明 ,与接枝环氧树脂水分散液相比 ,杂化水分散液的粒径和粘度均减小 .按此探讨了形成杂化水分散液的历程 .初步测定了杂化水分散液成膜后的表面性能 ,发现它们具有更高的硬度和更好的疏水性能 ,与成膜过程中硅溶胶在膜表面的富集效应有关     

Enhancement of properties of polyimide/silica hybrid nanocomposites by benzimidazole formed hydrogen bond

Polyimide/silica hybrid nanocomposites were prepared by sol–gel method without coupling agent. A novel diamine with a benzimidazole group, 2‐(4‐aminophenyl)‐5‐aminobenzimidazole (PABZ), was introduced to copolymerize with 4,4'‐oxydianiline (ODA) and pyromellitic dianhydride (PMDA) to synthesize polyimide (PI) matrix. The compatibility between PI and silica was improved by hydrogen bonds formed between silica phase and the –NH– group on benzimidazole of the new diamine. Highly transparent hybrid films were obtained when silica content reached as high as 30 wt%. SEM results show that silica particles with sizes much smaller than that in PMDA‐ODA/silica system disperse homogeneously in the PI matrix. Differing from most hybrid systems without coupling agent, the tensile strength of PABZ system increases from 152 MPa to 165 MPa with silica content increasing from 0 to 20 wt%, while, it decreases linearly in PMDA‐ODA system. DMA analysis shows that the introduction of PABZ largely increases the glass transition temperature (Tg) for all silica contents, which is suggested to be due to the more rigid structures and stronger interaction between the two phases. Meanwhile, the decomposition temperature and char yields at 800 °C are both higher than that of pure PIs. The structures of the hybrid films were identified by FTIR spectra, which indicate that different silica morphologies are developed, resulted from the hydrogen bonds between benzimidazole and silica phase. Copyright © 2011 John Wiley & Sons, Ltd.     

Hydrophilic nature and sorption-diffusion properties of nanocomposite hybrid polysulfone films

Hybrid nanocomposite films containing silica (??11.4 wt.%) or titania (??18.8 wt.%) in the polymer matrix were prepared by the sol-gel method using the hydrolytic polycondensation of tetraethoxysilane and tetrabutoxysilane in a THF solution of aromatic polymer, polysulfone (PSF). The influence of the oxide nature and the film composition on the structure, the interaction of the polymer with oxides, hydrophilicity, and sorption-diffusion properties of the hybrid films were studied by FTIR spectroscopy, atomic force microscopy, dynamic light scattering, and a complex of other physicochemical methods. The absence of chemical or intermolecular hydrogen bonds between the polymer and oxide particles in the PSF films was shown. The average size of the oxides (SiO₂, ??20 nm; TiO₂, ??90 nm) in the films and roughness of their surface (??0.2?C0.8 nm) were determined. The introduction of oxides into the polymer matrix increases the hydrophilic properties and the ability of the PSF films to swell in water; the diffusion coefficients of water and permeability of water vapor in the PSF films also increase. Titania also induces a more considerable change in the structure of the polymer matrix and more strongly affects the sorption-diffusion properties of the hybrid films in aqueous solutions of THF. All prepared nanocomposite films PSF/SiO₂ and PSF/TiO₂ are capable of extracting an organic component from aqueous solutions and can be used as sorbents and membrane films for the removal of organic substances from the aqueous medium.     

Sol-gel reaction in acrylic polymer emulsions: the effect of particle surface charge

Acrylic polymer-silica hybrid emulsions were synthesized from both anionic and cationic polymer emulsions by simple post-addition of tetraethoxysilane as a silica precursor. Solvent resistance of the films from the hybrid emulsions and the zeta-potential of the hybrid emulsions suggested the different forms of silica components in each hybrid emulsion. Thermal gravimetric analysis, 29Si NMR measurements, and transmission electron microscope observations revealed that the hybrid emulsion from the anionic polymer emulsion was a mixture of anionic polymer particles and homogeneously dissolved silicate oligomer-polymer. On the contrary, the hybrid emulsion from cationic polymer emulsion consisted of polymer core-silica shell particles. The electrostatic interaction between the cationic polymer particle surface and the silicate would be responsible for the accumulation of the silicate onto the particle surface, leading to the silica shell layer formation. The sol-gel condensation reaction of silicate in the acidic emulsion phase was revealed to be controllable by the surface charge of the coexisting particles.     

Preparation and properties of poly(vinyl alcohol)/silica nanocomposites derived from copolymerization of vinyl silica nanoparticles and vinyl acetate

Nanocomposites of poly(vinyl alcohol)/silica nanoparticles (PVA-SNs) were prepared by in-situ radical copolymerization of vinyl silica nanoparticles functionalized by vinyltriethoxysilane (VTEOS) and vinyl acetate with benzoyl peroxide (BPO, i.e., initiator), subsequently saponified via direct hydrolysis with NaOH solution. The resulting vinyl silica nanoparticles, PVA-SNs were characterized by means of fourier transformation spectroscopy (FTIR), transmission electron microscopy (TEM) and the elemental analysis method. Effects of silica nanoparticles on viscosity and alcoholysis of PVA-SNs were studied by a ubbelohode capillary viscometer and the back titration method. The morphological structure of PVA-SN films was investigated by scanning electron microscopy (SEM). Differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and tensile test were used to determine the thermal and mechanical properties of PVA-SN films. The results indicated that the content of vinyl groups on the surface of the vinyl silica nanoparticles was up to 3.02 mmol/g and vinyl silica nanoparticles had been successfully copolymerized with vinyl acetate. Furthermore, compared to pure PVA, silica nanoparticles bonded with polymer matrix in a low concentration affected the viscosity and alcoholysis of the PVA-SNs materials. At the same time, it resulted in the improvement of the thermal and mechanical properties of the PVA-SN materials due to a strong interaction between silica nanoparticles and the polymer matrix via a covalent bond. It could be found that the optical clarity of the membrane was changed through UV-Vis absorption spectrum due to the introduction of silica nanoparticles.     

Preparation and characterization of polymer/silica nanocomposites via double in situ miniemulsion polymerization

Polymer/SiO₂ nanocomposite microspheres were prepared by double in situ miniemulsion polymerization in the presence of methyl methacrylate, butyl acrylate, γ‐methacryloxy(propyl) trimethoxysilane, and tetraethoxysilane (TEOS). By taking full advantage of phase separation between the growing polymer particles and TEOS, inorganic/polymer microspheres were fabricated successfully in a one‐step process with the formation of SiO₂ particles and the polymerization of organic monomers taking place simultaneously. The morphology of nanocomposite microspheres and the microstructure, mechanical properties, thermal properties, and optical properties of the nanocomposite films were characterized and discussed. The results showed that hybrid microspheres had a raspberry‐like structure with silica nanoparticles on the shells of polymer. The silica particles of about 20 nm were highly dispersed within the nanocomposite films without aggregations. The transmittance of nanocomposite film was comparable to that of the copolymer film at around 70–80% from 400 to 800 nm. The mechanical properties and the fire‐retardant behavior of the polymer matrix were improved by the incorporation of silica nanoparticles. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3128–3134, 2010     

Microstructure and properties of 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA)‐p‐phenylene diamine (PDA) polyimide/poly(vinylsilsesquioxane) hybrid nanocomposite films

Hybrid nanocomposite films of poly(vinylsilsesquioxane) (PVSSQ) and polyimide (PI) (PI/PVSSQ) were prepared via sol‐gel process from triethoxyvinylsilane (VSSQ) and thermal imidization from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA)‐p‐phenylene diamine (PDA) polyamic acid (BPDA‐PDA PAA). We investigated the microstructure; interfacial interaction; and optical, thermal, dielectric, and mechanical properties of the hybrid films. The phase morphologies and degree of surface roughness were evaluated by scanning electron microscope (SEM) and atomic force microscope (AFM), respectively. It was found that the surface topography was influenced by the composition of PVSSQ. Hydrogen bonding interactions between polyimide (PI) matrix and PVSSQ domains were proved with FT‐IR spectroscopy. The transparency of the hybrid films was found to be dependent on the PVSSQ content. Incorporating of the PVSSQ in the hybrid composites increased the glass transition temperature of PI. Dielectric constants of the hybrid films were in the range of 2.37–3.59. Properties of the PI films were also significantly enhanced by adding 5–30 wt % of PVSSQ. For comparison, we also prepared the hybrid composites of PI and mixtures of VSSQ and tetraethoxysilane (TEOS) and the PI/silica hybrid composite containing 30 wt % of silica obtained from TEOS. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5189–5199, 2004     

Optical,thermal and microstructural studies of epoxy-CoSO4.7H2O hybrid material

Organic–inorganic polymer hybrid films of epoxy polymer were prepared, using Cobaltous sulfate heptahydrate (CoSO₄.7H₂O) as a filler component, by physical blending method. UV–Vis optical absorption spectra were analyzed to determine optical band gaps (E_g) of the hybrid material. FTIR studies revealed the interaction of inorganic component with molecules of the polymer matrix. Glass transition temperature (T_g) and degradation temperature were determined by DSC. TG analysis showed the improvement in thermal stability of prepared hybrid films. XRD patterns revealed the amorphous nature of the pure epoxy polymer. Additional sharp peaks were seen for higher filler levels (FLs), indicating self formed nanostructures in the material, which was also evident from SEM analysis.     

Crystallization of inorganic silica based on interaction between polyimide and silica by sol–gel method

Crystalline silica in cristobalite phase was successfully prepared at a relatively low temperature of 800 °C by calcinating polyimide/silica hybrid films under ambient air. X-ray photoelectron spectroscopy measurements show that the product is silica after calcination. It is found that the crystallinity is dependent on the removing rate and the strength of the interaction between polyimide and silica. The presence of polyimide plays an important role in the growth of silica. Calcination to remove polyimide with rapid heating results in lower crystallinity compared with calcination with slow heating. For samples with the same content of silica, the crystallinity changes with the strength of the interaction between polyimide and silica molecules.     

硅胶基质高效液相色谱填料研究进展

高效液相色谱(HPLC)不仅是一种有效的分析分离手段,也是一种重要的高效制备分离技术。色谱柱是HPLC系统的核心,不同性能的填料是HPLC广泛应用的基础。硅胶是开发最早、研究最为深入、应用最为广泛的HPLC固定相基质,其制备方法主要有喷雾干燥法、溶胶-凝胶法、聚合诱导胶体凝聚法及模板法等。近年来,亚2μm小粒径硅胶、核-壳型硅胶、双孔径硅胶、介孔性硅胶、有机杂化硅胶等新型硅胶应用于HPLC并取得了色谱分离技术的飞速发展,例如基于亚2μm填料的超高压液相色谱技术、基于核-壳型填料的快速分离技术、基于杂化硅胶填料的高温液相色谱技术等。硅胶经表面化学键合、聚合物包覆等有机改性可制得先进的大分子限进填料、温敏性填料、手性填料等,大大扩展了HPLC的应用范围。本文对液相色谱用硅胶的制备方法、改性与修饰方法以及硅胶基质固定相的评价方法加以系统综述,概述了新型硅胶在HPLC中的应用进展,并对硅胶基质填料的发展方向与应用前景进行了展望。     

Organic–inorganic nanocomposites of (2‐hydroxypropyl)cellulose as a precursor of nanocrystalline zinc oxide layers

The sol–gel method of synthesis of the hybrid nanocomposite films of ZnO/(2‐hydroxypropyl) cellulose (HPC) on silica glass is presented. The sol phases were prepared for different weight ratios of zinc acetate dihydrate to HPC in the presence of triethylamine (TEA). Raman spectrum of the mixture of ZnAc and HPC indicates coordinating interaction between zinc ion and HPC. The generation of ZnO nanoparticles in the HPC matrix proceeds in situ through the annealing of the gel phase at a temperature of 160°C. Identification of ZnO nanoparticles in the HPC matrix is done by using photoluminescence (PL), UV–Vis, and Raman spectroscopy. The films of ZnO/HPC nanocomposite are transparent in the visible light and show a higher energy value of absorption edge compared with ZnO in the bulk. Nanocrystalline films of ZnO were obtained by the calcination of ZnO/HPC nanocomposite at 500°C. ZnO films possess a good transparency for the visible light and high absorbance for UV light. Nanocrystallite sizes of ZnO particles were estimated from the X‐ ray lines broadening. The properties of ZnO layers were studied by the evaluation of PL, X‐ray investigation and atom force microscope (AFM) scanning, and the optical absorption edge. Copyright © 2008 John Wiley & Sons, Ltd.     

Poly(methyl methacrylate)/silica/titania ternary nanocomposites with greatly improved thermal and ultraviolet-shielding properties

Poly(methyl methacrylate) (PMMA)/silica/titania ternary nanocomposites with covalent bonding interaction between polymer and inorganic phases have been prepared using a novel non-hydrolytic sol-gel method. Transmission electron microscope (TEM) image of silica/titania binary inorganic component indicates a core-shell-like structure. Scanning electron microscope (SEM) images suggest that the well dispersed silica/titania particles in the hybrid are on the nanometer-scale. The transparencies of nanocomposites are maintained in visible region while the absorption band in ultraviolet (UV) region is red shifted with increasing inorganic content. The thermogravimetric analysis (TGA) results show that the thermal stability of PMMA copolymer increases dramatically with the addition of silica/titania moieties both in nitrogen and in air.     

Preparation of polyimide/silica hybrid material by sol–gel process under basic catalysis: Comparison with acid conditions

Hybrid polyimide/silica materials were prepared from polyimides bearing reactive functions along the polymer backbone, which can react with. The silica phase was formed by sol–gel process using ammonium hydroxide catalyst. Silica fillers prepared under basic conditions were compared with materials prepared using chlorhydric acid. The synthesized hybrid materials were characterized by TGA, IRTF, and NMR. The density of the different systems was also measured. The morphology of these hybrid systems were investigated by both scanning and transmission electron microscope. Thermal properties of the composites were also evaluated by DSC and DMA. The morphology of silica fillers highly depends on the catalyst, on the reaction conditions of the sol–gel process, and the linking formation with the polyimide. It results that optimized conditions lead to homogeneous hybrid films containing 12 wt % of silica particles of about 20 nm. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1891–1902, 2008     

Preparation of thick silica films in the presence of poly(acrylic acid) by using electrophoretic sol-gel deposition

Thick silica films were fabricated by electrophoretic sol-gel deposition of silica particles on a stainless steel sheet. Using sols prepared by the sol-gel method with poly(acrylic acid) (PAA) films of ca. 25 m in thickness were prepared with no cracks. The films were shown to be agglomerates of monodispersed silica particles with PAA. The size of the silica particles decreased with an increase in the added amount of PAA. The deposited weight was considerably larger for the films with PAA than that of the films without PAA.     

Crosslinked organosiloxane hybrid materials prepared by condensation of silanol and modified silica: Synthesis and characterization

Hybrid materials based on polymethylphenylsiloxane (PMPS) and organic functionalized silica were synthesized via condensation reaction between silanol and alkoxysilyl groups in the presence of quaternary ammonium hydroxide. The structure of prepared materials was investigated by FTIR and NMR, which indicate that the products have incorporated modified silica into the polymer matrix. The prepared hybrid materials show a satisfactory thermal resistance because the initial decomposition of typical product occurred at nearly 100 K higher than that of the pure polymer according to the thermogravimetric analysis (TGA) results. Differential thermogravimetric analysis (DTGA) data confirm that the thermal degradation of prepared hybrid materials comprises of two steps, of which the first one could be controlled by adjusting the content of silica particles and the ratio of surface groups on the particles. The coating films obtained from hybrid products exhibit good thermal mechanical properties. Therefore, the materials are hoped to be used for the application in thermal resistant coating.     

The preparation of non-extractable methylphenylpolysiloxane stationary phases for capillary column gas chromatography

Summary The synthesis of methylphenylpolysiloxane polymers and their use in the preparation of crosslinked, non-extractable stationary phases for fused-silica capillary columns are described. By preparing more viscous phenyl-containing polymers than are commercially available, stationary phase films of these polymers could be efficiently coated on fused-silica capillary columns and stabilized by a free radical crosslinking mechanism using peroxides. Four methylphenylpolysiloxane polymers containing different phenyl concentrations were prepared. These included three polymers containing 50% phenyl and one polymer containing 70% phenyl. Two of the 50% phenyl polymers had one phenyl and one methyl group attached to each silicon atom. One of these also had 1% vinyl incorporated. The third 50% phenyl polymer was synthesized in such a way that one half of the silicon atoms had two phenyl groups attached while the rest contained dimethyl groups. The 70% phenyl polymer also had 4% vinyl incorporated. Due to the intrinsic thermal stability of these phenyl phases and the enhanced film stability achieved by crosslinking, the 70% phenyl phase could be utilized up to 400 °C. Using the methods described in this paper, highly efficient and thermally stable fused silica capillary columns coated with crosslinked methylphenylpolysiloxane stationary phases can be successfully prepared.