基于多角度无透镜傅里叶变换数字全息的散斑噪声抑制成像研究

在数字全息成像中,散斑噪声严重影响了再现像的信噪比和成像分辨率,因此为了提高数字全息成像质量,迫切需要抑制再现像的散斑噪声.分析并给出了矩形散射光斑的强度协方差,定量计算了特定实验条件下产生退相关散斑图样的最小角度差.结合透镜的性质设计并搭建了多角度无透镜傅里叶变换数字全息成像系统,利用光纤端面在透镜焦平面的二维机械移动代替传统反射镜的旋转,使照明光束在不改变照明位置和大小的同时,可任意改变光束方向.移动光纤端面使多角度照明满足最小角度差,获取了81幅数字全息图.利用单次快速傅里叶逆变换实现数值再现,对多幅再现像的强度像求平均,实验结果表明散斑对比度降低为单幅再现像的14.6%,使图像信噪比提高了6.9倍.该抑制散斑的多角度数字全息成像方法有效的抑制了散斑噪声,且成像光路结构简单,可操作性强.     

Adaptive speckle reduction of ultrasound images based on maximum likelihood estimation

A method has been developed in this paper to gain effective speckle reduction in medical ultrasound images.To exploit full knowledge of the speckle distribution, here maximum likelihood was used to estimate speckle parameters corresponding to its statistical mode. Then the results were incorporated into the nonlinear anisotropic diffusion to achieve adaptive speckle reduction. Verified with simulated and ultrasound images,we show that this algorithm is capable of enhancing features of clinical interest and reduces speckle noise more efficiently than just applying classical filters. To avoid edge contribution, changes of contrast-to-noise ratio of different regions are also compared to investigate the performance of this approach.     

Precision of degree of polarization estimation in the presence of additive Gaussian detector noise

We address the problem of degree of polarization (DOP) estimation in images limited by additive Gaussian detector noise. We derive and analyze the probability density function (PDF) of the pixelwise DOP estimate, which is shown to have significantly different statistical properties than when noise is Gamma distributed (speckle). We then determine the Cramer-Rao Lower Bound and the maximum likelihood estimator of the DOP. We deduce from this study practical solutions for characterizing and reducing the noise in these images.     

Full-field heterodyne interference microscope with spatially incoherent illumination

A heterodyne interference microscope arrangement for full-field imaging is described. The reference and object beams are formed with highly correlated, time-varying laser speckle patterns. The speckle illumination confers a confocal transfer function to the system, and by temporal averaging, the coherence noise that often degrades coherent full-field microscope images is suppressed. The microscope described is similar to a Linnik-type microscope and allows the use of high-numerical-aperture objective lenses, but the temporal coherence of the illumination permits the use of a low-power achromatic doublet in the reference arm. The use of a doublet simplifies alignment of the microscope and can reduce the cost. Preliminary results are presented that demonstrate full-field surface height precision of 1 nm rms.     

Speckle characteristics of a broad-area VCSEL in the incoherent emission regime

We present a technique to reduce the speckle contrast of a NIR broad-area VCSEL based on the spatially incoherent emission regime that can be obtained when using the proper driving conditions. We evaluate the efficiency of this technique to reduce the speckle contrast by comparing it with the speckle characteristics in multimode emission under cw operation. Depending on the illumination setup, the incoherent emission regime can lead to a strongly reduced speckle contrast down to 1.3%. This is in agreement with estimates of the expected speckle contrast reduction when three contrast reducing effects are taken into account. These low contrast values make the investigated sources attractive for several applications that suffer from speckle noise.     

Detection theory approach to multichannel pattern location

We propose and assess new algorithms for detecting and locating an object in multichannel images. These algorithms are optimal for additive Gaussian noise and maximize the likelihood of the observed images. We consider two cases, in which the illumination of the target and the variance of the noise in each channel are either known or unknown. We show that in the latter case the algorithm provides accurate estimates of variance and luminance. These algorithms can be viewed as postprocessed versions of the correlation of a reference with the scene image in each channel.     

Introducing speckle noise maps for Laser Vibrometry

When coherent light scatters from a surface, which is rough on the scale of the wavelength of the light, a speckle pattern is produced. The Laser Vibrometer measures target vibration velocity in the direction of the incident laser beam and typically samples a region of a speckle pattern on its photodetector. Target motions can cause the speckle pattern to change on the photodetector surface, particularly when target motions are non-normal to the direction of the laser beam. This speckle motion modulates the Doppler signal and adds noise to the demodulated output signal. Periodic target motions can cause the speckle noise to become pseudo-random and produce harmonic peaks, with the same fundamental frequency as the genuine target vibrations, which can be indistinguishable from the genuine target vibrations. Typical speckle noise levels are generally considered to be low-level, but they have not so far been adequately quantified. This paper reports preliminary results quantifying speckle noise levels using controlled experimental configurations incorporating periodic in-plane and tilt target motions. Working with commercial Laser Vibrometers, various target surface finishes and treatments are considered and speckle noise maps are produced for each configuration. For a tilting surface, speckle noise has been quantified at approximately 1 μm s^?1/deg s^?1 while, for surfaces with in-plane motion, the sensitivity to speckle noise has been estimated pessimistically at 0.1% of the in-plane velocity. Ultimately, these speckle noise maps will form a valuable practical resource for the Laser Vibrometer user.     

基于斑点噪声的拖尾Rayleigh分布的合成孔径雷达图像最大后验概率降噪

为了反映合成孔径雷达图像中斑点噪声尖峰厚尾的统计特征，使用拖尾Rayleigh分布来描述斑点噪声.基于Gamma先验分布和斑点噪声的拖尾Rayleigh分布，推导出了合成孔径雷达图像的最大后验概率滤波方程，并给出了它在特定特征参数时的解析形式.使用Mellin变换从观察图像估计拖尾Rayleigh分布的未知参数.给出了在斑点噪声的拖尾Rayleigh分布下的最大后验概率降噪试验和量化指标.为了消除滑动窗大小和噪声强度对降噪结果的影响，给出了降噪能力随滑动窗大小和噪声方差的动态变化关系.结果表明，拖尾Ray 关键词： 斑点噪声 拖尾Rayleigh分布 最大后验概率降噪 Mellin变换     

Comparative analysis of the resolving power of optoelectronic imaging systems upon incoherent and coherent illumination of objects

Results of calculations of the resolving power (according to Foucault) of optoelectronic imaging systems with incoherent and coherent illumination under the conditions of atmospheric phase distortions are presented. It is suggested that incoherent optical images are formed in the case of incoherent illumination and speckle images are formed in the case of coherent illumination. The shape of objects observed is estimated from these images. The resolving powers are shown to be practically the same in the formation of incoherent optical images and speckle images in the case of strong phase distortions and smoothing of images by a matrix photodetector. At the same time, the limiting resolving power in the formation of incoherent optical images is twice as large as in the formation of speckle images.     

Improvement of speckle noise suppression in digital holography by rotating linear polarization state

An improved polarization recording approach to reduce speckle noise in digital holography is proposed. Multiple off-axis holograms are obtained by rotating the linear polarization state of both illumination and reference wave simultaneously. By averaging the intensity fields, the speckle noise in the reconstructed images is well suppressed. Statistical evaluation of the experimental results shows the effectiveness and improvement of the proposed method.     

Speckle noise reduction in digital holography by use of multiple polarization holograms

A novel speckle reduction technique for digital holography is proposed. Multiple off-axis holograms are recorded using a circularly polarized illumination beam and a rotating linearly polarized reference beam. The speckle noise in the reconstructed images is suppressed by averaging these fields. We demonstrate the effectiveness of this technique experimentally and conduct additional statistical evaluation.     

Anisotropy of near-field speckle patterns

In the vicinity of a rough interface under normal illumination the speckle field has been found to be anisotropic; that is, its correlation length is much larger in the direction of polarization than in the perpendicular direction, forming stripe-shaped speckle patterns in the near-field region. Furthermore, with increasing distance from the interface, the anisotropy of the near-field speckles decays rapidly, while the speckle size increases drastically in all directions. Based on detailed analysis, it was found that the anisotropy of the near-field speckle patterns can be attributed to polarization-dependent coupling among the evanescent waves from different surface diffusers.     

象面斑纹噪声相乘性的进一步探讨

本文导出了部分偏振斑纹象强度的n阶矩,考察了部分偏振象面斑纹噪声相乘性的统计学论据,并讨论了部分偏振斑纹象乘法模型的均方误差。最后讨论了N个等强度照明的独立直线偏振斑纹象非相干叠加时乘法模型的有效性。 关键词：     

基于Gabor滤波的散斑条纹图平滑方法

提出了一种基于伽博(Gabor)滤波的散斑条纹图平滑方法.通过加窗傅里叶运算提取散斑条纹图的条纹频率和条纹梯度方向,并利用它们确定具有频率和方向选择性的Gabor滤波器对散斑条纹图进行Gabor滤波.数值模拟和实验结果表明,该方法在滤除散斑噪声的同时能够有效的保留散斑条纹图的条纹结构,为从单幅散斑条纹图中进一步提取条纹相位场奠定了良好的基础.     

Surface roughness measurement using spatial-average analysis of objective speckle pattern in specular direction

The speckle contrast method (SCM) and the light scattering method (LSM) are two of the most promising optical techniques for on-line surface roughness measurement of slightly-rough surface. However, due to the lack of capability in eliminating the influence from the diffuse component of scattered light, SCM and LSM are both sensitive to the variations of surface correlation length. Additionally, for LSM, the presence of speckle noise leads to fluctuations in the measuring results. To solve these problems, an approach based on the spatial-average analysis of the objective speckle pattern in the specular direction, simply called spatial-average method (SAM), is proposed. The SAM establishes the quantitative relationship between a new characteristic parameter extracted from the recorded speckle image and the rms surface roughness, eliminates to a large extent the influence of diffuse light component on the measuring results, and immunizes itself from the speckle noise. The theoretical foundation of SAM is given in details. A computer simulation is then performed to make comparisons among these three methods. Finally an experiment is presented.     

Influence of the sparsity of random speckle illumination on ghost imaging in a noise environment

The influence of the sparsity of random speckle illumination on traditional ghost imaging(GI) and GI via sparsity constraint(GISC) in a noise environment is investigated. The experiments demonstrate that both GI and GISC obtain their best imaging quality when the sparsity of random speckle illumination is 0.5, which is also explained by some parameters such as detection of the signal to noise ratio and mutual coherence of the measurement matrix.     

基于散斑干涉的光滑表面变形快速检测

针对目前光滑表面力学性能测试困难的情况,建立了一种改进的数字激光散斑干涉测量系统。首先通过新的散斑干涉光路设计实现散斑照射,同时采用空间载波傅里叶变换法,对光滑零件加载变形的动态散斑干涉图像进行处理,最后得到光滑表面的变形场分布情况。该方法不对被测表面进行任何处理,可实现光滑表面的高精度全场变形测量。实验结果表明:最大变形处为镜面板的中央,测得最大变形量分别为1.936、1.861和1.797μm,与中心变形预设值接近。该方法光路简单、测量方案切实可行,能够实现光滑表面变形的快速动态测量。     

Stereophotogrammetric 3D shape measurement by holographic methods using structured speckle illumination combined with interferometry

We present a unique combination of the numerical three-dimensional (3D) reconstruction of the shape of an object with interferometric deformation measurements. Two cameras record several holograms of an object that is illuminated by structured illumination. This illumination is realized by speckle patterns. To improve the image quality, an inplace speckle reduction technique is combined with the structured illumination to reduce the effect of disturbing subjective speckles which appear in the reconstructed images. Stereophotogrammetric methods are applied to extract the 3D surface information of the object out of the reconstructed images. Since the recording is done by holography and because stereophotogrammetry enables a pointwise correlation between the two views, it is possible to combine other holographic techniques with the reconstructed 3D shape. This is demonstrated by an interferometric deformation measurement of an object cooling down. The resulting interferometric fringes are mapped onto the reconstructed 3D surface. Hence, the proposed method enables automatic and dense matching of interferometric fringe-maps recorded by spatially separated holograms onto the surface of the object, which has not yet been realized by existing techniques.     

Surface contouring by phase-shifting digital holography

Surface contouring by phase-shifting digital holography is proposed that provides surface height from a change of reconstructed object phases due to the tilt of object illumination. Surface height from a reference plane is directly obtained from the phase change. Its sensitivity depends on the tilt angle as well as on the initial incident angle. By proper selection of the angles we can derive surface height without phase unwrapping. The sensitivity can be enhanced by increasing the tilt angle. Then we need phase unwrapping that is sensitive to noise due to laser speckles in the reconstructed images. This noise could be suppressed by selecting phase values at points of the maximum product of amplitudes before and after the illumination change in the course of data reduction from 1024×1024 to 512×512 and by selecting paths for phase unwrapping by looking for the intensity maximum. The observed height resolution is 20 μm. Effects of numerical focusing have also been investigated. The present method has the same sensitivity as the fringe projection method, but it has larger measurement depth and is also applicable to the deformation measurement with the same arrangement.     

Speckle reduction by selective spatial-domain mask in digital holography

An improved method of using a selective spatial-domain mask to reduce speckle noise in digital holography is proposed.The sub-holograms are obtained from the original hologram filtered by the binary masks including a shifting aperture for being reconstructed. Normally, the speckle patterns of these sub-reconstructed images are different. The speckle intensity of the final reconstructed image is suppressed by averaging the favorable sub-reconstructed images which are selected based on the most optimal pixel intensity sub-range in the sub-holograms. Compared with the conventional spatial-domain mask method, the proposed method not only reduces the speckle noise more effectively with fewer sub-reconstructed images,but also reduces the redundant information used in the reconstruction process.