Flexible Polyester Cellulose Paper Supercapacitor with a Gel Electrolyte

A low-cost polyester cellulose paper has been used as a substrate for a flexible supercapacitor device that contains aqueous carbon nanotube ink as the electrodes and a polyvinyl alcohol (PVA)-based gel as the electrolyte. Gel electrolytes have attracted much interest due to their solvent-holding capacity and good film-forming capability. The electrodes are characterized for their conductivity and morphology. Because of its high conductivity, the conductive paper is studied in supercapacitor applications as active electrodes and as separators after coating with polyvinylidene fluoride. Carbon nanotubes deposited on porous paper are more accessible to ions in the electrolyte than those on flat substrates, which results in higher power density. A simple fabrication process is achieved and paper supercapacitors are tested for their performance in both aqueous and PVA gel electrolytes by using galvanostatic and cyclic voltammetry methods. A high specific capacitance of 270 F g⁻¹ and an energy density value of 37 W h kg⁻¹ are achieved for devices with PVA gel electrolytes. Furthermore, this device can maintain excellent specific capacitance even under high currents. This is also confirmed by another counter experiment with aqueous sulfuric acid as the electrolyte. The cycle life, one of the most critical parameters in supercapacitor operations, is found to be excellent (6000 cycles) and less than 0.5 % capacitance loss is observed. Moreover, the supercapacitor device is flexible and even after twisting does not show any cracks or evidence of breakage, and shows almost the same specific capacitance of 267 F g⁻¹and energy density of 37 W h kg⁻¹. This work suggests that a paper substrate can be a highly scalable and low-cost solution for high-performance supercapacitors.     

Paper-based piezoresistive MEMS sensors

This paper describes the development of MEMS force sensors constructed using paper as the structural material. The working principle on which these paper-based sensors are based is the piezoresistive effect generated by conductive materials patterned on a paper substrate. The device is inexpensive (～$0.04 per device for materials), simple to fabricate, lightweight, and disposable. Paper can be readily folded into three-dimensional structures to increase the stiffness of the sensor while keeping it light in weight. The entire fabrication process can be completed within one hour without expensive cleanroom facilities using simple tools (e.g., a paper cutter and a painting knife). We demonstrated that the paper-based sensor can measure forces with moderate performance (i.e., resolution: 120 μN, measurement range: ±16 mN, and sensitivity: 0.84 mV mN(-1)). We applied this sensor to characterizing the mechanical properties of a soft material. Leveraging the same sensing concept, we also developed a paper-based balance with a measurement range of 15 g, and a resolution of 0.39 g.     

Capacitive sensing of droplets for microfluidic devices based on thermocapillary actuation

The design and performance of a miniaturized coplanar capacitive sensor is presented whose electrode arrays can also function as resistive microheaters for thermocapillary actuation of liquid films and droplets. Optimal compromise between large capacitive signal and high spatial resolution is obtained for electrode widths comparable to the liquid film thickness measured, in agreement with supporting numerical simulations which include mutual capacitance effects. An interdigitated, variable width design, allowing for wider central electrodes, increases the capacitive signal for liquid structures with non-uniform height profiles. The capacitive resolution and time response of the current design is approximately 0.03 pF and 10 ms, respectively, which makes possible a number of sensing functions for nanoliter droplets. These include detection of droplet position, size, composition or percentage water uptake for hygroscopic liquids. Its rapid response time allows measurements of the rate of mass loss in evaporating droplets.     

Dynamically Resettable Electrode-Electrolyte Interface through Supramolecular Sol-Gel Transition Electrolyte for Flexible Zinc Batteries

Flexible batteries based on gel electrolytes with high safety are promising power solutions for wearable electronics but suffer from vulnerable electrode-electrolyte interfaces especially upon complex deformations, leading to irreversible capacity loss or even battery collapse. Here, a supramolecular sol-gel transition electrolyte (SGTE) that can dynamically accommodate deformations and repair electrode-electrolyte interfaces through its controllable rewetting at low temperatures is designed. Mediated by the micellization of polypropylene oxide blocks in Pluronic and host-guest interactions between α-cyclodextrin (α-CD) and polyethylene oxide blocks, the high ionic conductivity and compatibility with various salts of SGTE afford resettable electrode-electrolyte interfaces and thus constructions of a series of highly durable, flexible aqueous zinc batteries. The design of this novel gel electrolyte provides new insights for the development of flexible batteries.     

Field‐Effect Nanoparticle‐Based Glucose Sensor on a Chip: Amplification Effect of Coimmobilized Redox Species

A capacitive EIS (electrolyte‐insulator‐semiconductor) structure was modified with gold nanoparticles together with glucose oxidase and used as field‐effect‐based glucose biosensor using the constant capacitance mode. Co‐immobilization of ferrocene redox species resulted in a two‐fold increase of the biosensor sensitivity. The effect was explained by the hydrogen peroxide‐mediated oxidation of ferrocene resulting in a pool of charged species at the interface increasing the sensor response towards glucose. The studied approach was suggested as a general means to amplify signals from Si chip‐based field‐effect enzyme biosensors.     

一种高透明、可拉伸导电水凝胶的制备及其在电容传感器中的应用

导电水凝胶由于具备良好的电学特性、可调节的机械性能、易于加工性和生物相容性等,是制备柔性电子设备的理想基材。本文使用马来酸与丙烯酰胺作为共聚单体,氯化锂作为导电离子,N,N'-二甲基双丙烯酰胺作为交联剂,使用光引发剂,采用原位光聚合的方式制备了一种导电水凝胶。制得的水凝胶可见光透过率高达93%,最大拉伸形变~380%,导电率最大为12 S/m。鉴于其优异的综合性能,实验中使用导电水凝胶制备了电容传感器并应用于人体活动监测。结果表明,制备的导电水凝胶电容传感器对不同程度的手指弯曲形变和不同力度的手指触碰均表现出灵敏的响应行为,为未来可穿戴柔性电子产品的发展起到了一定的推动作用。     

Conductive Film with Flexible and Stretchable Capability for Sensor Application and Stealth Information Transmission

Flexible and wearable strain sensors for human-computer interaction, health monitoring, and soft robotics have drawn widespread attention to promising applications in the next generation of artificial intelligence devices. However, conventional semiconductor sensors are difficult to meet the requirements of flexibility and stretchability. Here, we reported a kind of novel and simple sensor based on layer-by-layer(LBL) method. Carbon nanotubes (CNTs) layer provides high ductility and stability in the process of tension sensing, while silver layer provides low initial resistance and fast reflecting in the process of tension sensing. LBL method ensures the uniformity of the conductive layer. The sensor has superior sheet resistance of 9.44Ω/sq., high elongation at break of 104%. For sensing capability, the sensor has wide reflecting range of 60%, high gauge factor (GF) of 1000 up to 60%strain, fast reflecting time of 165 ms. Excellent reliability and stability have also been verified. It is also worth mentioning that the entire process does not require any expensive equipments, complicated processes or harsh experimental conditions. The above features provide an idea for large-scale application of flexible stretchable sensors.     

Electrode modification and the response of the acoustic shear wave device operating in liquids

The effect of electrode polarity, geometry, and stray capacitance on the performance of the thickness-shear mode acoustic wave sensor operating in electrolytes and solutions of biomolecules has been studied. In contrast to the well-known mass-based response of the device operating in the gas phase, the response in a liquid is governed by several factors including acoustoelectric and fringing field effects, which are known to be active at the edges of the electrodes. In order to investigate and utilize these effects, we modified the electrode geometry to increase the edge length, which, in turn, raises the sensitivity of the device. These changes which constituted either complete coverage of the back of the device with electrode material, or the removal of disks and lines from the electrode surface, resulted in a two to three times enhancement of sensor response. Such modifications that extend device sensitivity beyond the electrode area to the quartz region of the sensing structure also provide a better surface for the immobilization of various probes. We verified the enhancing ability of the modified electrodes for the case of adsorption of the protein avidin and neutravidin, followed by their affinity reactions with biotinylated biomolecules. It was found that the active electrode in contact with electrolyte exhibits a sensitivity of about twice that of the grounded electrode. The existence of stray capacitance around the cell was confirmed by shielding the cell assembly with a bath of concentrated KCl solution. This shielding effect was measured to be about 25-60 Hz in series resonant frequency and -1000 Hz in parallel resonant frequency.     

A stable and convenient protein electrophoresis titration device with bubble removing system

Moving reaction boundary titration (MRBT) has a potential application to immunoassay and protein content analysis with high selectivity. However, air bubbles often impair the accuracy of MRBT, and the leakage of electrolyte greatly decreases the safety and convenience of electrophoretic titration. Addressing these two issues a reliable MRBT device with modified electrolyte chamber of protein titration was designed. Multiphysics computer simulation was conducted for optimization according to two‐phase flow. The single chamber was made of two perpendicular cylinders with different diameters. After placing electrophoretic tube, the resident air in the junction next to the gel could be eliminated by a simple fast electrolyte flow. Removing the electrophoretic tube automatically prevented electrolyte leakage at the junction due to the gravity‐induced negative pressure within the chamber. Moreover, the numerical simulation and experiments showed that the improved MRBT device has following advantages: (i) easy and rapid setup of electrophoretic tube within 20 s; (ii) simple and quick bubble dissipates from the chamber of titration within 2 s; (iii) no electrolyte leakage from the two chambers: and (iv) accurate protein titration and safe instrumental operation. The developed technique and apparatus greatly improves the performance of the previous MRBT device, and providing a new route toward practical application.     

Skin‐worn Soft Microfluidic Potentiometric Detection System

A flexible skin‐mounted microfluidic potentiometric device for simultaneous electrochemical monitoring of sodium and potassium in sweat is presented. The wearable device allows efficient natural sweat pumping to the potentiometric detection chamber, containing solid‐contact ion‐selective Na⁺ and K⁺ electrodes, during exercise activity. The fabricated microchip electrolyte‐sensing device displays good analytical performance and addresses sweat mixing and carry‐over issues of early epidermal potentiometric sensors. Such soft skin‐worn microchip platform integrates potentiometric measurement, microfluidic technologies with flexible electronics for real‐time wireless data transmission to mobile devices. The new fully integrated microfluidic electrolyte‐detection device paves the way for practical fitness and health monitoring applications.     

Development of a Biomimetic MEMS based Capacitive Tactile Sensor

This paper presents the development of a low-cost MEMS based biomimetic tactile device intended to be incorporated as the core element in a biomimetic fingerpad. The developed silicon based sensing devices consist of an array of capacitive sensors with optimized design to measure force ranges encountered during tactile exploration of surfaces with different textures. As with the biological finger, the sensor array contains sensors of different sensitivity and position/orientation, guaranteeing a high informative content of data obtained from surface-finger interaction. This paper presents the design of the device, fabrication processes used and experimental results of sensor performance.     

Bioinspired design of highly sensitive flexible tactile sensors for wearable healthcare monitoring

The design of microscale architectures integrated with low-dimensional nanomaterials for tactile sensors has attracted considerable attention owing to their high performance for various potential applications, especially in the field of healthcare monitoring. However, there still remains a critical challenge to achieve high sensitivity in response to different magnitude external pressure. Herein, we introduce a high performance capacitive tactile sensor based on Silver nanowires coated biomimetic hierarchical array architecture, which consists of mini-domes by the way of vacuum adsorption from through-hole arrays and micro-cones by duplicating Calathea zebrina leaf, respectively. This hybrid graded microstructure as electrode exhibits remarkably improved sensitivity and stimulus responding range when compared with the other monotonous counterparts. Moreover, an optimized ionic gel film with remarkable interfacial capacitance is sandwiched by microstructured electrodes as the dielectric layer, further boosting the performance of the tactile sensor. As a result, the obtained sensor demonstrates a board detection range from 24 Pa to 90 kPa with a maximum sensitivity of 37.8 kPa^?1, and a fast response time (<78 ms). These superior performances of our tactile sensor lay a foundation for various applications in healthcare monitoring. It can not only sense and distinguish subtle arterial pulse signals even under different ages, genders and states of motion but also monitor physiological activity with large pressure as well, such as breathing, plantar pressure, and so on. We envision this bionic tactile sensor holds great potential in wearable electronics.     

当前和下一代锂离子电池电解液的原子尺度微观认识和研究进展

电解液及构筑电极电解液界面对于开发和应用高比容量储能系统至关重要。具体来说，电解液的机械（抗压性、粘度）、热（热导率和热容）、化学（溶解性、活度、反应性）、输运和电化学（界面及界面层）等性质，与其所组成的储能器件的性能直接相关。目前，大量的实验研究通过调控电解液的物理和/或化学组成来改善电解液性能，以满足新型电极材料的工作运行。与此同时，理论模拟方法近年来得到了迅速发展，使人们可以从原子尺度来理解电解液在控制离子输运和构筑功能化界面的作用。站在理论模拟研究的前沿上，人们可以利用其所揭示的机理性认识对新型电解液开展理性设计。本文首先总结了传统电解液的组成、溶剂化结构和输运性质以及电极电解液界面层的形成机理，进一步讨论了利用新型电解液设计稳定电极电解液界面层的方法，包括使用电解液添加剂、高浓电解液和固态电解质，并着重讨论了对这些新型电解液体系进行原子尺度模拟的最新进展，为了解和认识电解液提供更为基本的理解，并为未来电解液的设计提供系统的指导。最后，作者对新型电解液的理论筛选进行了展望。     

CP@NiAl-LDH复合材料的制备及其超级电容器性能

通过采用简易温和的水热条件制备导电聚合物@镍铝层状双金属氢氧化物复合材料(CP@NiAl-LDH),构建电子/离子的高速传输纳米通道,利用SEM和XRD对复合材料结构形貌进行表征。电化学性能测试结果表明,导电聚合物为复合材料提供一定的赝电容,促进电荷的快速转移,使CP@NiAl-LDH的电容性能得以显著提升。PPy@LDH具有最好的电容性能,在1 A·g~(-1)的电流密度下,其比容量高达3 010.3 F·g~(-1),当电流密度升高到20 A·g~(-1)时,其比电容保持率为73.1%,表现出优异的倍率性能;同时,在10 A·g~(-1)的电流密度下10 000次充放电循环后仍具有88.8%的比容量保持率,具有优异的循环稳定性。这主要归功于NiAl-LDH与导电聚合物之间的协同增强效应。     

NASICON-based H2 Sensor Using CoCrMnO4 Insensitive Reference Electrode and Buried Au Sensing Electrode

This work focuses on the H2 sensing performance of the sensor with buried Au sensing electrode and spi- nel-type oxide CoCrMnO4 insensitive reference electrode within sodium super ionic conductor（NASICON） film. The sensor showed the highest response to H2 gas on the insensitive material sintering at 800 ~C. Compared with those of the traditional structure device, the sensitivity and selectivity of the sensor using buried sensing electrode were greatly improved, giving a response of-177 mV in 9x10 5 g/L H2, which was about 3.5 times higher than that of sensors with traditional structure. Moreover, the AV value of the sensing device exhibited linear relationship to the logarithm of H2 concentration and the sensitivity（slope） was -135 mV/decade. A sensing mechanism related to the mixed potential was proposed for the present sensor.     

CP@NiAl-LDH复合材料的制备及其超级电容器性能

通过采用简易温和的水热条件制备导电聚合物@镍铝层状双金属氧化物复合材料（CP@NiAl-LDH）,构建电子/离子的高速传输纳米通道,利用SEM和XRD对复合材料结构形貌进行表征。电化学性能测试结果表明,导电聚合物为复合材料提供一定的赝电容,促进电荷的快速转移,使CP@NiAl-LDH的电容性能得以显著提升。PPy@LDH具有最好的电容性能,在1 A·g^-1的电流密度下,其比容量高达3 010.3 F·g^-1,当电流密度升高到20 A·g^-1时,其比电容保持率为73.1%,表现出优异的倍率性能;同时,在10 A·g^-1的电流密度下10 000次充放电循环后仍具有88.8%的比容量保持率,具有优异的循环稳定性。这主要归功于NiAl-LDH与导电聚合物之间的协同增强效应。     

Three dimensional graphene transistor for ultra-sensitive pH sensing directly in biological media

In this work, pH sensing directly in biological media using three dimensional liquid gated graphene transistors is presented. The sensor is made of suspended network of graphene coated all around with thin layer of hafnium oxide (HfO₂), showing high sensitivity and sensing beyond the Debye-screening limit. The performance of the pH sensor is validated by measuring the pH of isotonic buffered, Dulbecco's phosphate buffered saline (DPBS) solution, and of blood serum derived from Sprague-Dawley rat. The pH sensor shows high sensitivity of 71 ± 7 mV/pH even in high ionic strength media with molarities as high as 289 ± 1 mM. High sensitivity of this device is owing to suspension of three dimensional graphene in electrolyte which provides all around liquid gating of graphene, leading to higher electrostatic coupling efficiency of electrolyte to the channel and higher gating control of transistor channel by ions in the electrolyte. Coating graphene with hafnium oxide film (HfO₂) provides binding sites for hydrogen ions, which results in higher sensitivity and sensing beyond the Debye-screening limit. The 3D graphene transistor offers the possibility of real-time pH measurement in biological media without the need for desaltation or sample preparation.     

A novel, sensitive potentiometric hydrocarbon sensor for high-vacuum applications

A potentiometric device based on interfacing a solid electrolyte oxygen ion conductor with a thin platinum film acts as a robust, reproducible sensor for the detection of hydrocarbons in high- or ultrahigh-vacuum environments. Sensitivities in the order of approximately 5 x 10(-10) mbar are achievable under open circuit conditions, with good selectivity for discrimination between n-butane on one hand and toluene, n-octane, n-hexane, and 1-butene on the other hand. The sensor's sensitivity may be tuned by operating under constant current (closed circuit) conditions; injection of anodic current is also a very effective means of restoring a clean sensing surface at any desired point. XPS data and potentiometric measurements confirm the proposed mode of sensing action: the steady-state coverage of Oa, which sets the potential of the Pt sensing electrode, is determined by the partial pressure and dissociative sticking probability of the impinging hydrocarbon. The principles established here provide the basis for a viable, inherently flexible, and promising means for the sensitive and selective detection of hydrocarbons under demanding conditions.     

A Stable Solid Polymer Electrolyte for Lithium Metal Battery with Electronically Conductive Fillers

Electronic conduction in solid-polymer electrolytes is generally not desired, which causes leakage of electrons or energy loss, and the electronically conductive domains at electrode-electrolyte interfaces can lead to continuous decomposition of electrolytes and shorting issues. However, it is noticed in this work that in an insulating matrix, the conductive domains at certain aspects could also have positive effects on the electrolyte performance with proper control. This work evaluates the limitation and benefits of electronically conductive domains in a solid-polymer electrolyte system and discusses the approach to improve the electrolyte physicochemical properties with densified local electric field distribution, enhanced bulk dielectric property, and charge transfer. By deliberately introducing the conductive domains in a regular solid-polymer electrolyte, stable cycle life, low overpotential, and promising full cell performance could be achieved.     

Design and fabrication of a shielded interdigital sensor for noninvasive In situ real‐time production monitoring of polymers

Interdigital sensors (IDS) have received great attention for production monitoring of polymers over the past decade. However, conventional IDS are limited by high noise to environment due to the dual side access of the sensor, low nominal capacitance, and sensitivity. In this study, a shielded IDS fabricated by flexible circuit board (FCB) technology is presented to overcome these challenges. Compared to conventional sensors, the environmental dependence of the new sensor is minimized by the copper shield. Furthermore, nominal capacitance of at least 350% higher, and an increase of sensitivity per unit area are achieved. To demonstrate the capabilities of the new IDS, a FCB comprising the proposed sensor is fabricated, attached to a mould, and successfully applied for in situ real‐time production monitoring of an epoxy resin. The resulting flexible sensor is noninvasive towards the fabricated parts, and measures the key stages along the production process. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2028–2037