High-performance silicon nanowire array photoelectrochemical solar cells through surface passivation and modification

Nanowire solar cells: Pt nanoparticle (PtNP) decorated C/Si core/shell nanowire photoelectrochemical solar cells show high conversion efficiency of 10.86 % and excellent stability in aggressive electrolytes under 1-sun AM 1.5 G illumination. Superior device performance is achieved by improved surface passivation of the nanowires by carbon coating and enhanced interfacial charge transfer by PtNPs.     

Highly efficient photoelectrochemical hydrogen generation using a ZnO nanowire array and a CdSe/CdS co-sensitizer

Highly efficient photoelectrochemical (PEC) hydrogen generation was achieved by fabricating CdSe deposited ZnO/CdS core/shell nanowire (NW) array photoanodes by a facile three-step solution-based method. Well-defined electrical pathways in 1-dimensional (1D) NW structures allowed efficient charge carrier collection, and CdSe/CdS co-sensitization enabled utilization of the visible region in the solar spectrum. PEC devices using CdSe/CdS/ZnO NW arrays showed improved absorption spectra, and they demonstrated a remarkable enhancement in PEC performance. Our proposed structure is a promising candidate photoanode for solar energy-to-hydrogen conversion devices.     

Spectral broadening in quantum dots-sensitized photoelectrochemical solar cells based on CdSe and Mg-doped CdSe nanocrystals

In order to absorb a broad spectrum in visible region, a co-sensitized TiO₂ electrode was prepared by CdSe and Mg-doped CdSe quantum dots (Q dots). The power conversion efficiency of the co-sensitized Q dots photoelectrochemical solar cells (PECs) showed 1.03% under air mass 1.5 condition (I = 100 mW/cm²), which is higher than that of individual Q dots-sensitized PECs. The incident-photon-to-current conversion efficiency of the co-sensitized PECs showed absorption peaks at 541 and 578 nm corresponding to the two Q dots and displayed a broad spectral response over the entire visible spectrum in the 500–600 nm wavelength domains.     

Synthesis of hybrid solar cells using CdS nanowire array grown on conductive glass substrates

High-density CdS nanowire (NW) arrays were successfully grown on fluorine-doped tin oxide (FTO)-coated glass substrates by vapor–liquid–solid (VLS) mechanism at a remarkably reduced temperature of ～450 °C. Bi catalyst layer and polyvinyl alcohol (PVA) played a major role in the low-temperature synthesis of high-quality CdS NW arrays. CdS NWs were defect free single crystalline Wurtzite crystals and they were 50–100 nm and 2–5 μm in diameter and length, respectively. CdS NWs were combined with poly[2-methoxy-5-(2′-ethylhexyloxy)-1,4-phenylenevinylene] (MEH-PPV), a conjugated polymer to form organic–inorganic hybrid structures. The UV–visible light absorption and emission behavior of MEH-PPV/CdS hybrids was investigated and their potential to be used as photovoltaic cells was demonstrated.     

Apollony photonic sponge based photoelectrochemical solar cells

We have developed a quasi-fractal colloidal crystal to localize efficiently photons in a very broad optical spectral range; it has been applied to prepare dye sensitized photoelectrochemical solar (PES) cells able to harvest very efficiently photons from the ultraviolet (UV) and the visible (VIS) regions of the solar spectrum.     

CuO/Cu2O nanowire array photoelectrochemical biosensor for ultrasensitive detection of tyrosinase

Photoelectrochemical(PEC) biosensors have shown great promise in bioanalysis and diagnostic applications in recent years. In this work, the CuO/Cu_2O nanowire array(CuO/Cu_2O Nanowire) supported on copper foam was prepared as a photocathode for detection of tyrosinase though quinone-chitosan conjugation chemistry method. The in-situ generated quinones that were the catalytic product of tyrosinase acted as electron acceptors, which were captured by the chitosan deposited on the surface of the electrode. Direct immobilization of electron acceptor on the electrode surface improved the photocurrent conversion efficiency and thus sensitivity. The as-prepared biosensor can realize a rapid response in a wide linear range of 0.05 U/mL to 10 U/mL with the detection limit as low as 0.016 U/mL of tyrosinase. The current work provides a new perspective to design and develop highly sensitive and selective PEC biosensor.     

CdSe/TiO2 nanocrystalline solar cells

CdSe sensitized TiO₂ nanocrystalline solar cells were made with the participation of silicotungstic acid (STA) during the deposition of CdSe, the resulting Voc and Isc were 0.23 V cm^-2 and 10 mA cm^-2, respectively. The doping, time and microporous membrane effects were also discussed.     

GaP/GaPN核壳纳米线阵列修饰的硅光阴极的光电化学制氢反应（英文）

能够大规模同时提升电极的催化效率和稳定性对光电化学分解水系统的开发具有重要意义.硅是一种地球储量丰富且成熟的工业材料,由于其合适的带隙(1.1 eV)和优异的导电性,已被广泛用于光电化学制氢反应.然而,缓慢的表面催化反应和在电解液中的不稳定性限制了其在太阳能制氢中的实际应用.III-IV族半导体材料也具有较高的载流子传输特性且被广泛用于光电器件.其中,GaP的直接带隙和间接带隙分别为2.78和2.26 eV,可与硅组成串联型光电极用于光电化学分解水.然而,GaP的光腐蚀电位位于禁带中,很容易在光电催化过程中发生光腐蚀而导致性能大幅下降.本文报道了一种新型的GaP/GaPN核/壳纳米线修饰的p型硅(p-Si)串联型光阴极,同未修饰的p-Si相比,其光电化学制氢性能更高.这可归因于以下几点:(1)p-Si和GaP纳米线之间形成的p-n结促进了电荷分离;(2)GaPN相对于GaP具有更低的导带边位置,进一步促进了光生电子向电极表面的转移;(3)纳米线结构既缩短了光生载流子的收集距离,又增加了比表面积,从而加快了表面反应动力学.此外,在GaP中引入氮元素还提高了体系的光吸收和稳定性.我们所提出的高效、简便的改进策略可应用于其他的太阳能转换体系.利用简单的化学气相沉积法制备GaP/GaPN核/壳纳米线修饰的p-Si光阴极.首先在p-Si衬底上利用Au纳米颗粒作为催化剂生长GaP纳米线;然后,去除Au催化剂,并在氨气中退火便形成了GaP/GaPN核壳纳米线.高分辨透射电子显微镜,拉曼光谱和X射线光电子谱的表征结果均证实了氨气退火使得GaP纳米线表面形成了GaPN的薄壳层,同时证明了GaP/GaPN核壳纳米线具有可调的核壳结构.在模拟太阳光下作为光阴极用于光解水制氢反应时,GaP/GaPN核壳纳米线修饰的p-Si光阴极的起始电位为~0.14 V,而未修饰的p-Si电极的起始电位大约在?0.77 V.而且,GaP/GaPN核/壳纳米线修饰的p-Si光阴极比未修饰的p-Si光阴极具有更高的光电流密度,在水的还原电位下,其光电流密度为?0.3 mA cm^-2,且饱和光电流密度在?0.76 V时达到了?8.8 mA cm^-2.此外,GaP/GaPN核/壳纳米线修饰的p-Si光阴极的光电化学活性在10 h内没有发生明显下降.由此可见GaP/GaPN核/壳纳米线可以规模化有效地提升Si光电极的催化效率和稳定性.     

Silicon nanowire radial p-n junction solar cells

We have demonstrated a low-temperature wafer-scale etching and thin film deposition method for fabricating silicon n-p core-shell nanowire solar cells. Our devices showed efficiencies up to nearly 0.5%, limited primarily by interfacial recombination and high series resistance. Surface passivation and contact optimization will be critical to improve device performance in the future.     

Hybrid heterojunction solar cell based on organic-inorganic silicon nanowire array architecture

Silicon nanowire arrays (SiNWs) on a planar silicon wafer can be fabricated by a simple metal-assisted wet chemical etching method. They can offer an excellent light harvesting capability through light scattering and trapping. In this work, we demonstrated that the organic-inorganic solar cell based on hybrid composites of conjugated molecules and SiNWs on a planar substrate yielded an excellent power conversion efficiency (PCE) of 9.70%. The high efficiency was ascribed to two aspects: one was the improvement of the light absorption by SiNWs structure on the planar components; the other was the enhancement of charge extraction efficiency, resulting from the novel top contact by forming a thin organic layer shell around the individual silicon nanowire. On the contrary, the sole planar junction solar cell only exhibited a PCE of 6.01%, due to the lower light trapping capability and the less hole extraction efficiency. It indicated that both the SiNWs structure and the thin organic layer top contact were critical to achieve a high performance organic/silicon solar cell.     

Crossed BiOI flake array solar cells

We report a new kind of solar cell based on crossed flake-like BiOI arrays for the first time. The BiOI flake arrays were fabricated on an FTO glass with a TiO₂ block layer at room temperature by successive ionic layer adsorption and reaction (SILAR) method. The resulting BiOI flake array solar cell exhibited enhanced photovoltaic performance under solar illumination. This work provides an attractive and new solar cell system and a facile route to fabricate low cost and non-toxic solar cell.     

Multilayer assembly of nanowire arrays for dye-sensitized solar cells

Vertically ordered nanostructures synthesized directly on transparent conducting oxide have shown great promise for overcoming the limitations of current dye-sensitized solar cells (DSCs) based on random networks of nanoparticles. However, the synthesis of such structures with a high internal surface area has been challenging. Here we demonstrate a convenient approach that involves alternate cycles of nanowire growth and self-assembled monolayer coating processes for synthesizing multilayer assemblies of ZnO nanowire arrays and using the assemblies for fabrication of DSCs. The assembled multilayer ZnO nanowire arrays possess an internal surface area that is more than 5 times larger than what one can possibly obtain with single-layer nanowire arrays. DSCs fabricated using such multilayer arrays yield a power conversion efficiency of 7%, which is comparable to that of TiO(2) nanoparticle-based DSCs. The ordered structure with a high internal surface area opens up opportunities for further improvement of DSCs.     

Dendritic nanowire ultraviolet laser array

Self-organized dendritic crystal growth is explored to assemble uniform semiconductor nanowires into highly ordered one-dimensional microscale arrays that resemble comb structures. The individual ZnO nanowires have uniform diameters ranging from 10 to 300 nm. They are evenly spaced on a stem with a regular periodicity of 0.1-2 micrometer. Under optical excitation, each individual ZnO nanowire serves as a Fabry-Perot optical cavity, and together they form a highly ordered nanowire ultraviolet laser array.     

Current density enhancement for quantum dot-sensitized solar cells by modulation on the quantum dot loading amount of anatase nanowire array photoelectrodes

Journal of Solid State Electrochemistry - A second spin-coating process was employed for CuInS2 quantum dot (QD)-sensitized TiO2 nanowire-based solar cells, which is anticipated to increase the QD...     

Self-assembled hybrid polymer-TiO2 nanotube array heterojunction solar cells

Films comprised of 4 microm long titanium dioxide nanotube arrays were fabricated by anodizing Ti foils in an ethylene glycol based electrolyte. A carboxylated polythiophene derivative was self-assembled onto the TiO2 nanotube arrays by immersing them in a solution of the polymer. The binding sites of the carboxylate moiety along the polymer chain provide multiple anchoring sites to the substrate, making for a stable rugged film. Backside illuminated liquid junction solar cells based on TiO2 nanotube films sensitized by the self-assembled polymeric layer showed a short-circuit current density of 5.5 mA cm-2, a 0.7 V open circuit potential, and a 0.55 fill factor yielding power conversion efficiencies of 2.1% under AM 1.5 sun. A backside illuminated single heterojunction solid state solar cell using the same self-assembled polymer was demonstrated and yielded a photocurrent density as high as 2.0 mA cm-2. When a double heterojunction was formed by infiltrating a blend of poly(3-hexylthiophene) (P3HT) and C60-methanofullerene into the self-assembled polymer coated nanotube arrays, a photocurrent as high as 6.5 mA cm-2 was obtained under AM 1.5 sun with a corresponding efficiency of 1%. The photocurrent action spectra showed a maximum incident photon-to-electron conversion efficiency (IPCE) of 53% for the liquid junction cells and 25% for the single heterojunction solid state solar cells.     

Dye-sensitized solar cells based on anatase TiO2 nanoparticle/nanowire composites

Dye-sensitized solar cells were fabricated based on the composites of anatase TiO2 nanoparticles and single crystalline anatase TiO2 nanowires. Nanoparticle/nanowire composites can possess the advantages of both building blocks, i.e., the high surface area of nanoparticle aggregates and the rapid electron transport rate and the light scattering effect of single-crystalline nanowires. Three different composites were prepared with 5 wt %, 20 wt %, and 77 wt % nanowires, respectively. The performances of composite solar cells were compared with pure nanoparticle cells at a series of film thickness. With low nanowire concentrations (5 wt % and 20 wt %), the composite films maintain similar specific surface area as the pure nanoparticle films, while the composite cells show higher short-circuit current density and open-circuit voltage. An enhancement of power efficiency from 6.7% for pure nanoparticle cells to 8.6% for the composite cell with 20 wt % nanowires has been achieved under 1 Sun AM1.5 illumination (100 mW/cm2). For the composite film with 77 wt % nanowires, the nanowires became the major phase. Their less compact packing resulted in significant decrease of the specific surface area, and thus the current density. However, with the increase of film thickness, the current density showed a continuous increase in the whole thickness range up to 17 microm, indicating the improved electron diffusion length due to the formed nanowire network. The nanowires also helped to preserve crack-free thick films. These results show that employing nanoparticle/nanowire composites represents a promising approach for further improving the efficiencies of sensitized solar cells.