The influence of chitosan on in vitro properties of Eudragit RS microspheres

Eudragit RS microspheres containing chitosan hydrochloride were prepared by the solvent evaporation method using acetone/liquid paraffin solvent system and their properties were compared with Eudragit RS microspheres without chitosan, prepared in our previous study. Different stirring rates were applied (400-1200 rpm) and drug content, Higuchi dissolution rate constant, surface and structure characteristics of the microspheres were determined for each size fraction. An increase in average particle size with a reduction of stirring rate appeared in limited interval in both series. The average particle size of microspheres without chitosan, prepared at the same stirring rate, was smaller. Pipemidic acid content increased with increasing fraction particle size, but not with increasing stirring rate as it was observed for microspheres without chitosan. We presume that high pipemidic acid content in larger microspheres is a consequence of cumulation of undissolved pipemidic acid particles in larger droplets during microspheres preparation procedure. Pipemidic acid release was faster from microspheres with chitosan and no correlation between Higuchi dissolution rate constant and stirring rate or fraction particle size was found, though it existed in the system without chitosan. Structure and surface characteristics of microspheres observed by scanning electron microscope (SEM) were not changed significantly by incorporation of chitosan. But in contrast with microspheres without chitosan, the surface of chitosan microspheres was more porous after three hours of dissolution. It is supposed that the influence of particle size fraction and stirring rate on release characteristics is expressed to a great extent through porosity and indirectly through total effective surface area, but the incorporation of highly soluble component i.e. chitosan salt hides these effects on drug release. In conclusion, changes in biopharmaceutical properties due to varying stirring rate and fraction particle size exhibited the same direction as those reported for the microspheres without chitosan, although they are less expressed because of increased experimental variability, likely caused by chitosan.     

Facile fabrication of chitosan active film with xylan via direct immersion

Chitosan film was immersed in NaOH solution with xylan to simply prepare active chitosan/xylan film. FT-IR, XRD, FE-SEM, AFM and XPS were used to evaluate the effects of xylan on the structure and morphology of chitosan film, and a wide variety of material characteristics of the chitosan/xylan composite films were investigated. The results showed that the xylan chains entered into the gap of chitosan film and became nodules, leading to strong hydrogen bonds and electrostatic interactions between chitosan and xylan. Moreover, the introduction of xylan not only resulted in stronger crystallinity and a more compact structure of chitosan film, but also had an important effect on the properties of chitosan film. The tensile strength, breaking elongation and anti-ultraviolet performance of the chitosan/xylan films were improved greatly with the increasing concentration of xylan; the water vapor transmission rate, water absorption rate and oxygen barrier property of chitosan/xylan composite films were higher than those of chitosan film; chitosan/xylan composite films still showed hydrophobicity when the xylan concentration was more than 1 %. The chitosan/xylan composite film has more potential to be used as food packaging than pure chitosan film.     

肽类药物口服剂型材料及控制释放性能研究Ⅰ.壳聚糖─海藻酸盐微囊对胰岛素的控释作用

应用壳聚糖-海藻酸盐微囊技术制备了一系列胰岛素微囊，并研究了不同反应条件如海藻酸钠浓度、壳聚糖浓度、壳聚糖分子量及壳聚糖溶液pH值对微囊的胰岛素包封率及其释放性能的影响。结果表明，海藻酸钠浓度越高，微囊对胰岛素的包封率越高，在模拟小肠液中释放速率越低；壳聚糖浓度越大，微囊的胰岛素包封率及其在模拟胃液中释放率越高，在模拟肠液中释放达最大值所需时间越长；而随壳聚糖分子量减小，微囊在胃液中释放率增高；壳聚糖溶液pH值的变化对微囊的胰岛素包封率未造成明显影响。     

Effect of peroxide depolymerization of chitosan on properties of chitosan sulfate particles produced from this substance

Effect of the oxidative destruction of chitosan on the rate at which a dispersed phase is formed in its dilute solutions in the presence of sulfate ions and on the composition, size and ζ-potential of submicrometer chitosan sulfate particles being formed was studied. It was found that the particle size steadily decreases as the molecular mass of chitosan becomes smaller, and the sedimentation stability of aqueous dispersions increases in the absence of surfactants. The \(\nu _{SO_4 } :\nu _{NH_2 }\) molar ratio in chitosan sulfate particles is independent of the molecular mass of chitosan and varies within the range 0.45–0.46. A pH-dependence of the sign of the ζ-potential with isoelectric point at pH 5.0 was found for particles based on destructed chitosan.     

壳聚糖超声可控降解及降解动力学研究

通过正交实验法考察了壳聚糖溶液浓度、反应温度、超声强度以及醋酸溶液浓度对超声降解反应的影响,确定了最佳反应条件,制备了一系列不同分子量的壳聚糖.研究了壳聚糖溶液浓度、反应温度以及壳聚糖原料分子参数与降解速率常数的关系.通过红外光谱、X-射线衍射和凝胶渗透色谱对降解产物进行了表征.结果表明,超声降解壳聚糖的最佳条件为10℃,壳聚糖溶液浓度2.5g/L.降解速率常数随壳聚糖溶液浓度和反应温度的降低而增大.高分子量和低脱乙酰度的壳聚糖原料有较高的降解速率和降解速率常数,壳聚糖原料的分子量对降解速率和降解速率常数的影响大于脱乙酰度对其的影响.超声波导致了壳聚糖分子量的降低和产物晶体结构的破坏,但没有改变产物的脱乙酰度和糖残基结构.     

壳聚糖棒材表面仿生拒水改性的研究

分析壳聚糖棒材在湿态环境下力学性能衰减速率过快的原因,通过对植物叶拒水机理的仿生,将壳聚糖表面进行复合式仿生疏水改性.先对壳聚糖棒材表面进行酰化改性,降低了棒材表面极性,使棒材表面形成一种微观凹凸的粗糙结构.然后在此粗糙结构上进行生物酯涂覆,以达到仿植物叶的拒水效果.结果表明,壳聚糖棒材表面经过乙酰化处理,表面变得粗糙.经接触角实验和吸水速率测试表明,壳聚糖棒材表面经酰化改性后,降低了材料表面的极性及亲水性.通过控制酰化反应时间,能有效地增大棒材的接触角,使得最外层的生物酯涂层紧密结合,经模拟体液浸泡实验,该材料3个月内完全拒水,达到了预期的目的.     

Reaction kinetics of glycidyl trimethyl ammonium chloride and chitosan in 1-allyl-3-methylimidazolium chloride

The modification of chitosan in ionic liquids through homogeneous reactions has advantages including shorter time and simple post-treatment and the generated chitosan derivatives have high degrees of subsititution and good reproducibility. In this paper, we studied the reaction kinetics of glycidyl trimethyl ammonium chloride and chitosan in 1-allyl-3-methylimidazolium chloride. Chitosan concentration, temperature, and reaction time were studied to determine their influence on reaction kinetics. The results indicated that reaction rate increased with increases of both chitosan concentration and temperature. A first-order kinetics equation was generated, where the relationship between reaction rate constant and temperature was determined.     

Preparation of electrospun chitosan/poly(vinyl alcohol) membranes

Electrospinning of chitosan from its solutions in 2% aqueous acetic acid was studied by adding poly(vinyl alcohol) (PVA) as a “guest” polymer. Properties of the chitosan/PVA solutions including viscosity, conductivity, and surface tension were measured, and effects of the polymer concentration, chitosan/PVA mass ratio and processing parameters (applied voltage, flow rate, capillary-to-collector distance) on the electrospinnability of chitosan/PVA were investigated. Analyses of scanning electron micrographs and transmission electron micrographs suggested that the chitosan/PVA ultrafine fibers were often obtained along with beads, and chitosan was located in the elctrospun fibers as well as in the beads. Uniform chitosan/PVA fibers with an average diameter of 99 ± 21 nm could be prepared from a 7% chitosan/PVA solution in 40:60 mass ratio. Results of Fourier transform infrared spectroscopy and X-ray diffraction demonstrated that there were possible hydrogen bonds between chitosan and PVA molecules, which could weaken the strong interaction in chitosan itself and facilitate chitosan/PVA electrospinnability. The electrospun chitosan/PVA membranes showed higher water uptake and would have potential applications in wound dressings.     

ADSORPTION OF LDL ON THE MODIFIED CHITOSAN

In this paper,the selective adsorption of LDL on chitosan modified with PEG and Asp.was studied.The adsorption rate of LDL and HDL on the double modified chitosan was 57% and 12% respoectively,The results shown that the double modified chitosan can be used a adsorbent for selective binding to LDL,this work may help to develop functional columns for hemoperfusion.     

以壳聚糖为模板的对苯二酚氧化聚合反应表观动力学研究

以壳聚糖为模板在酸性溶液中实现了对苯二酚的氧化聚合.该反应必须在氧气存在的条件下才能进行.动力学研究表明该氧化聚合反应是以选取机理进行的模板聚合反应.当壳聚糖残基与对苯二酚的摩尔比小于0.8时,反应速度与壳聚糖浓度成正比.当壳聚糖残基与对苯二酚的摩尔比大于0.8时,反应速度不再随壳聚糖浓度提高而提高.反应对对苯二酚而言是一个一级反应.反应的活化能为71.6kJ/mol.     

High Substitution Synthesis of Carboxymethyl Chitosan for Properties Improvement of Carboxymethyl Chitosan Films Depending on Particle Sizes

This study investigated the effect of chitosan particle sizes on the properties of carboxymethyl chitosan (CMCh) powders and films. Chitosan powders with different particle sizes (75, 125, 250, 450 and 850 µm) were used to synthesize the CMCh powders. The yield, degree of substitution (DS), and water solubility of the CMCh powders were then determined. The CMCh films prepared with CMCh based on chitosan with different particle sizes were fabricated by a solution casting technique. The water solubility, mechanical properties, and water vapor transmission rate (WVTR) of the CMCh films were measured. As the chitosan particle size decreased, the yield, DS, and water solubility of the synthesized CMCh powders increased. The increase in water solubility was due to an increase in the polarity of the CMCh powder, from a higher conversion of chitosan into CMCh. In addition, the higher conversion of chitosan was also related to a higher surface area in the substitution reaction provided by chitosan powder with a smaller particle size. As the particle size of chitosan decreased, the tensile strength, elongation at break, and WVTR of the CMCh films increased. This study demonstrated that a greater improvement in water solubility of the CMCh powders and films can be achieved by using chitosan powder with a smaller size.     

Radiation synthesis of chitosan beads grafted with acrylic acid for metal ions sorption

Radiation-induced grafting of acrylic acid onto chitosan beads was performed in solution at a dose rate of 20.6 Gy/min of cobalt-60 gamma rays. The effect of absorbed dose on grafting yield was investigated. The characterization of the grafted material was performed by FTIR spectroscopy and the swelling measurements at different pHs. The grafting yield increased with the increase in dose, it reached 80% at 40 kGy irradiation dose.The removal of Pb and Cd ions from aqueous solutions was investigated with both ungrafted and grafted chitosan beads. The sorption behavior of the sorbents was examined through pH, kinetics and equilibrium measurements. Grafted chitosan beads presented higher sorption capacity for both metal ions than unmodified chitosan beads.     

乙酰化对壳聚糖-明胶海绵结构和性能的影响

用乙酸酐对壳聚糖与明胶共混物进行乙酰化,然后冷冻干燥制备乙酰化壳聚糖-明胶海绵,并研究乙酰化对海绵结构与性能的影响。用盐酸环丙沙星作模型药物,探讨载药海绵的抑菌效果。结果表明:制得的海绵具有多孔结构,随壳聚糖在混合物中含量的增加,海绵的吸水率和保水率先增后减;随着乙酰化程度的提高,海绵的吸水率先减后增,而保水率与吸水率的变化规律相反。酶对海绵的降解率不受壳聚糖和明胶混合比例的影响,但随海绵乙酰化程度的增加而增加。载药海绵的抑菌效果与海绵中壳聚糖含量有关。     

Poly(epsilon-caprolactone)/chitin and poly(epsilon-caprolactone)/chitosan blend films with compositional gradients: fabrication and their biodegradability

Poly(epsilon-caprolactone) (PCL)/chitin and PCL/chitosan blend films with compositional gradients were successfully fabricated by a dissolution/diffusion method; that is, repeatedly pouring the PCL/chitin (or PCL/chitosan) blend solutions, with variable composition, onto polysaccharide layers. The compositional gradient structure in the resulting films was characterized by polarized optic microscopy, ATR-FT-IR and trans-FT-IR microscopic spectroscopy. Enzymatic degradability of the PCL/chitin and PCL/chitosan blend films with compositional gradients in the presence of lysozyme was compared with those of homogeneous films and two-layer films. It was found that the degradation rate of PCL/chitin blend films with a compositional gradient was far lower than that of the neat chitin film, whereas the degradation rate of PCL/chitosan blend films with a compositional gradient was close to that of the neat chitosan film. The suppression of the chitosan crystallization, which accelerates the enzymatic degradation, at the surface of PCL/chitosan films with a compositional gradient was much more severe than that for PCL/chitin films with a compositional gradient.     

Preparation and properties of polyvinyl acetal sponge modified by chitosan

The polyvinyl acetal sponge modified by chitosan was prepared by adding chitosan/polyvinyl alcohol (PVA) solution during the acetalation reaction of PVA and formaldehyde. The effect of vesicant and chitosan to the pore morphology, water absorption ratio, water absorption rate, expansion time and mechanical properties were studied. The polyvinyl acetal sponge modified by chitosan was used as a hemostatic packing material for the injured rabbit nasal tissue. The hemostatic effect and the healing effect of the modified sponge on the nasal mucosa after nasal surgery were studied. The results indicated that the polyvinyl acetal sponge modified by chitosan has an interconnected pore structure and the wall between large pores also has small pores. The chitosan adhered on the inner surface of the pores. The increased content of vesicant led to an increase in pore diameter, in the water absorption ratio and in expansion time. However, there was only a small change in the water absorption rate and a decrease in tensile strength and compression strength were noted. With an increase in chitosan content, the pore diameter and interconnection of the sponge was reduced. Water absorption ratio, expansion time and water absorption rate decreased, but tensile strength and compression strength improved. Observation of the rabbit nasal tissue after surgical operation suggested that polyvinyl acetal sponge modified by chitosan has an anti-inflammatory, hemostatic and anti-adherent characteristic and could promote the healing and functional recovery of rabbit nasal mucosa. __________ Translated from Journal of Jinan University (Natural Science & Medicine Edition), 2007, 28(3): 283–287 [译自: 暨南大学学报(自然科学与医学版)]     

Biobased films prepared from NaOH/thiourea aqueous solution of chitosan and linter cellulose

In the present study, films based on linter cellulose and chitosan were prepared using an aqueous solution of sodium hydroxide (NaOH)/thiourea as the solvent system. The dissolution process of cellulose and chitosan in NaOH/thiourea aqueous solution was followed by the partial chain depolymerization of both biopolymers, which facilitates their solubilization. Biobased films with different chitosan/cellulose ratios were then elaborated by a casting method and subsequent solvent evaporation. They were characterized by X-ray analysis, scanning electron microscopy (SEM), atomic force microscopy (AFM), thermal analysis, and tests related to tensile strength and biodegradation properties. The SEM images of the biofilms with 50/50 and 60/40 ratio of chitosan/cellulose showed surfaces more wrinkled than the others. The AFM images indicated that higher the content of chitosan in the biobased composite film, higher is the average roughness value. It was inferred through thermal analysis that the thermal stability was affected by the presence of chitosan in the films; the initial temperature of decomposition was shifted to lower levels in the presence of chitosan. Results from the tests for tensile strength indicated that the blending of cellulose and chitosan improved the mechanical properties of the films and that an increase in chitosan content led to production of films with higher tensile strength and percentage of elongation. The degradation study in a simulated soil showed that the higher the crystallinity, the lower is the biodegradation rate.     

Gelation time and degradation rate of chitosan-based injectable hydrogel

Gelation time and degradation rate of thermally-sensitive aqueous solutions of chitosan/Gp (glycerophosphate disodium salt) have been studied. The effects of different parameters such as Gp salt concentration, solution temperature, degree of deacetylation of chitosan (DDA) and drug loading on the gelation time have been investigated. Gravimetric analysis, gel permeation chromatography and FTIR spectrophotometry were used to investigate the influence of the DDA and concentration of chitosan solution on hydrogel degradation. The presented results indicated that gelation time decreases by increasing Gp salt concentration, temperature, concentration and DDA of chitosan solutions, while drug loading has no significant effect on gelation time. Slower degradation profile was recorded for hydrogel with the higher DDA and concentration of chitosan in the primary solution. FTIR studies indicated that the chemical structure of chitosan macromolecules does not change significantly during the degradation. It could be concluded that biodegradation of chitosan hydrogel occurred via its surfaces.     

海藻酸-壳聚糖-海藻酸离子取代凝胶改性研究

羧甲基壳聚糖;微胶囊;海藻酸-壳聚糖-海藻酸离子取代凝胶改性研究     

Release characteristics of cisplatin chitosan microspheres and effect of containing chitin

To increase cisplatin (CDDP) content, to suppress burst effect during the initial phase of drug release, and to improve the capacity of the system for sustained release, we prepared various types of CDDP chitosan microspheres incorporating chitin and investigated the content of CDDP and its in vitro release kinetics from these microspheres. The results of this study showed that the CDDP content increased with increasing chitosan concentration and that the incorporation of chitin in the carrier matrix produced a more pronounced increase in drug content. The addition of chitin also led to inhibition of the initial burst effect. The rate of CDDP release reduced with increasing concentration of chitosan: that is, the 50% CDDP release time was about 0.5 h with the microspheres prepared with 1.0% of chitosan and about 4.5 h with those prepared with 5.0% of chitosan, indicating about nine-fold prolongation. The addition of chitin further resulted in retardation of the rate of CDDP release. Meanwhile, our chitosan microspheres were shown to undergo enzymatic degradation by lysozymes.     

壳聚糖膜的处理方法与其渗透汽化性能间的关系

对壳聚糖均质膜折脱酸处理、干燥方法与所得膜的渗透汽化性能间的关系进行了研究。结果表明，处理方法的不同直接影响到膜的透过、分离性能。用含３ｗｔ．％ＮａＯＨ的醇水溶液（乙醇／水＝５０／５０（ｗｔ．／ｗｔ．））进行脱酸处理的膜，其α水／乙醇值，在料液温度为５５－７５℃的范围内几乎不变。