Third-order nonlinear optical properties of multiwalled carbon nanotubes modified by CdS nanoparticles

CdS nanoparticles were coated on the side wall of multiwalled carbon nanotubes (MWCNTs) by a wet chemical synthesis approach via noncovalent functionalization of MWCNTs with poly(diallyldimethylammonium chloride) (PDDA). The as-prepared material was characterized by X-ray diffraction (XRD), UV–vis absorption, fluorescence and transmission electron microscopy (TEM). The results indicated that CdS nanoparticles were uniformly coated on the surface of MWCNTs. Third-order optical nonlinearity of the as-prepared material was studied with the Z-scan technique with picosecond laser pulses at 532 nm. The Z-scan curve revealed that CdS nanoparticle-modified MWCNTs exhibited negative nonlinear refraction index and positive absorption coefficient. The real part and imaginary part of the third-order nonlinear susceptibility χ⁽³⁾ were calculated to be −4.9 × 10⁻¹² and 6.8 × 10⁻¹³ esu, respectively.     

Investigations on structural, vibrational, morphological and optical properties of CdS and CdS/Co films by ultrasonic spray pyrolysis

CdS and CdS/Co films have been deposited on glass substrates by an ultrasonic spray pyrolysis method. The effects of Co incorporation on the structural, optical, morphological, elemental and vibrational properties of these films were investigated. XRD analysis confirmed the hexagonal wurtzite structure of all films and had no impurity phase. While CdS film has (0 0 2) as the preferred orientation, CdS/Co films have (1 1 0) as the preferred orientation. The direct optical band gap was found to decrease from 2.42 to 2.39 eV by Co incorporation. The decrease of the direct energy gaps by increasing Co contents is mainly due to the sp-d exchange interaction between the localized d-electrons of Co²⁺ ions and band electrons of CdS. After the optical investigations, it was seen that the transmittance of CdS films decreased by Co content. The Raman measurements revealed two peaks corresponding to the 1LO and 2LO modes of hexagonal CdS. The vibrational modes of Cd-S were obtained in the wavenumber range (590-715 cm⁻¹) using Fourier transform infrared spectroscopy (FTIR). The elemental analysis of the film was done by energy dispersive X-ray spectrometry.     

A facile strategy for the fabrication of uniform CdS nanowires with high yield and its controlled morphological growth with the assistance of PEG in hydrothermal route

A series of novel wurtzite cadmium sulphide (CdS) nanowires with uniform diameter were synthesized by using a rapid and simple solvothermal route. CdS nano structures with certain morphology could be selectively produced by only varying the concentration of poly ethylene glycol (PEG) as a surfactant in the reaction system with cadmium acetate, sulphur powder and ethelynediamine (EDA). We extensively studied UV-vis absorption spectra, photoluminescence spectra after confirming CdS nanowires with diameter 24-25 nm and length ranging up to several nano meters by field emission scanning electron microscopy (FE-SEM). Therefore we may definitely propose a new formation mechanism of CdS nanowires assisted by PEG with its illustrating optical properties.     

Optical characterization and determination of carrier density of ultrasonically sprayed CdS:Cu films

In this work, CdS and Cu doped CdS films (at the Cu percentages of 1, 3 and 5) have been deposited onto glass substrates at 350 ± 5 °C by ultrasonic spray pyrolysis technique and their application potential for photovoltaic solar cells have been investigated. Optical properties and thicknesses of the films have been investigated by spectroscopic ellipsometry (SE). Ellipsometric angle ψ was used as the source point for optical characterizations. The optical constants (n and k) and the thicknesses of the films have been fitted according to Cauchy model. Also, optical properties of the produced films have been analyzed by transmittance and reflectance spectra. Refractive index (n), extinction coefficient (k) and reflectance (R) spectra have been taken by spectroscopic ellipsometer, while transmittance spectra have been taken by UV/vis spectrophotometer. The optical method has been used to determine the band gap type and value of the films. Mott-Schottky (M-S) measurements have been made to determine the conductivity type and carrier concentration of the films. Samples showed n-type conductivity and carrier concentration of undoped CdS sample was found to be 1.19 × 10¹⁹ cm⁻³. Also, it was concluded that Cu doping has an acceptor effect in CdS samples. From the results of these investigations, the application potential of CdS:Cu films for photovoltaic solar cells as window layer was searched.     

Structural, optical and photoelectrochemical characterization of CdS nanowire synthesized by chemical bath deposition and wet chemical etching

Nanocrystalline thin films of CdS have been grown onto flexible plastic and titanium substrates by a simple and environmentally benign chemical bath deposition (CBD) method at room temperature. The films consist of clusters of CdS nanoparticles. The clusters of CdS nanoparticles in the films were successfully converted into nanowire (NW) networks using chemical etching process. The possible mechanism of the etching phenomenon is discussed. These films were examined for their structural, surface morphological and optical properties by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM) and UV-vis spectrophotometry techniques, respectively. Photoelectrochemical (PEC) investigations were carried out using cell configuration as n-CdS/(1 M NaOH + 1 M Na₂S + 1 M S)/C. The film of nanowires was found to be hexagonal in structure with the preferential orientation along the (0 0 2) plane. The nanowires have widths in the range of 50-150 nm and have lengths of the order of a few micrometers. Optical studies reveal that the CdS nanowires have value of band gap 2.48 eV, whereas it is 2.58 eV for nanoparticles of CdS. Finally, we report on the ideality of junction improvement of PEC cells when CdS nanoparticles photoelectrode converted into nanowires photoelectrode.     

Intersubband resonant enhancement of the nonlinear optical properties in asymmetric (CdS/ZnSe) based quantum wells

In this work, the linear and nonlinear optical properties are studied theoretically in asymmetric (CdS/ZnSe/BeTe)/(ZnSe/BeTe) quantum wells. The electronic states are calculated using the envelope wave function approximation and the intersubband transition energies are studied as a function of CdS and ZnSe well thicknesses as well as doping concentration. The optimum parameters carrying out the transition energy 0.8 eV (1.55 μm wavelength) are given. Results are presented for the linear, the third order nonlinear optical absorption and the refractive index changes in the studied heterostructure. Results show that the changes in the linear and the third order nonlinear optical absorption as well as refractive index change are as important as the temperature is high, the nonlinear terms must be taken into consideration especially near the resonance.     

Nonlinear optical properties in SrTiO3 thin films by pulsed laser deposition

Well-crystallized 250 nm-thick SrTiO₃ thin films on fused-quartz substrate were prepared by pulsed laser deposition. The band-gap of SrTiO₃ thin film by transmittance spectra is equal to 3.50 eV, larger than 3.22 eV for the bulk crystal. The nonlinear optical properties of the films were examined with picosecond pulses at 1.064 μm excitation. A large two-photon absorption (TPA) with absorption coefficient of 87.7 cm/GW was obtained, larger than 51.7 cm/GW for BaTiO₃ thin films. The nonlinear refractive index n₂ is equal to 5.7×10⁻¹⁰ esu with a negative sign, larger than 0.267×10⁻¹¹ esu for bulk SrTiO₃. The large TPA is attributed to intermediate energy levels introduced by the grain boundaries, and the optical limiting behaviors stemming from both TPA and negative nonlinear refraction were also discussed.     

Method for measurements of second-order nonlinear optical coefficient based on Z-scan

The method for measuring second-order nonlinear optical coefficients based on well-known Z-scan is presented. The influence of linear absorption coefficients on normalized transmittance is discussed. Using this method, we obtained the second-order nonlinear coefficient d₃₁(5%MgO:LiNbO₃) = 4.5 × 10⁻¹² m/v at 1064 nm, which agrees well with theoretical calculations and previous well-known values.     

Investigation of energy band gap and optical properties of cubic CdS epilayers

High quality cubic CdS epilayers were grown on GaAs (1 0 0) substrates by the hot-wall epitaxy method. The crystal structure of the grown epilayers was confirmed to be the cubic structure by X-ray diffraction patterns. The optical properties of the epilayers were investigated in a wide photon energy range between 2.0 and 8.5 eV using spectroscopic ellipsometry (SE) and were studied in the transmittance spectra at a wavelength range of 400-700 nm at room temperature. The data obtained by SE were analyzed to find the critical points of the pseudodielectric function spectra, 〈?(E)〉 = 〈?₁(E)〉 + i〈?₂(E)〉, such as E₀, E₁, E₂, E^′₀, and E^′₁ structures. In addition, the optical properties related to the pseudodielectric function of CdS, such as the absorption coefficient α(E), were investigated. All the critical point structures were observed, for the first time, at 300 K by ellipsometric measurements for the cubic CdS epilayers. Also, the energy band gap was determined by the transmittance spectra of the free-standing film, and the results were compared with the E₀ structure obtained by SE measurement.     

Optical properties of cadmium sulfide nanocrystal film prepared by electrochemical synthesis at liquid-liquid interface

Dendritic nanocrystalline CdS film was deposited at liquid-liquid interface of surfactants and an electrolyte containing 4 mmol L⁻¹ cadmium chloride (CdCl₂) and 16 mmol L⁻¹ thioacetamide (CH₃CSNH₂) with an initial pH value of 5 at 15 °C by electrochemical synthesis. The nanofilm was characterized by transmission electron microscopy (TEM), field emission scanning electron microscope (FE-SEM), atomic force microscopy (AFM), ultraviolet visible (UV-vis) absorption spectroscopy and fluorescence spectroscopy. The surface morphology and particle size of the nanofilm were investigated by AFM, SEM and TEM, and the crystalline size was 30-50 nm. The thickness of the nanofilm calculated by optical absorption spectrum was 80 nm. The microstructure and composition of the nanofilm was investigated by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), showing its polycrystalline structure consisting of CdS and Cd. Optical properties of the nanofilm were investigated systematically by UV-vis absorption and fluorescence spectroscopy. A λ_onset blue shift compared with bulk CdS was observed in the absorption spectra. Fluorescence spectra of the nanofilm indicated that the CdS nanofilm emitted blue and green light. The nanocomposites film electrode will bring about anodic photocurrent during illumination, showing that the transfer of cavities produces photocurrent.     

Optical and structural properties of CdS thin films grown by chemical bath deposition doped with Ag by ion exchange

In this work thin CdS films using glycine as a complexing agent were fabricated by chemical bath deposition and then doped with silver (Ag), by an ion exchange process with different concentrations of AgNO₃ solutions. The CdS films were immersed in silver solutions using different concentrations during 1 min for doping and after that the films were annealed at 200 °C during 20 min for dopant diffusion after the immersion on the AgNO₃ solutions. The aim of this research was to know the effects of different concentrations of Ag on the optical and structural properties of CdS thin films. The optical band gap of the doped films was determined by transmittance measurements, with the results of transmittance varying between 35% and 70% up to 450 nm in the electromagnetic spectra and the band gap varying between 2.31 and 2.51 eV depending of the silver content. X-ray photoelectron spectroscopy was used to study the influence of silver on the CdS:Ag films, as a function of the AgNO₃ solution concentration. The crystal structure of the thin CdS:Ag films was studied by the X-ray diffraction method and the film surface morphology was studied by atomic force microscopy. Using the ion exchange process, the CdS films’ structural, optical and electric characteristics were modified according to silver nitrate concentration used.     

Microstructural, optical and photocatalytic properties of CdS doped TiO2 thin films

CdS doped TiO₂ thin films (with CdS content=0, 3, 6, 9 and 12 at%) were grown on glass substrates. The X-ray diffraction analysis revealed that the films are polycrystalline of monoclinic TiO₂ structure. The microstructure parameters of the films such as crystallite size (D_ν) and microstrain (e) are calculated. Both the crystallites size and the microstrain are decreased with increasing CdS content. The optical constants have been determined in terms of Murmann's exact equations. The refractive index and extinction coefficient are increased with increasing CdS content. The optical band gap is calculated in the strong absorption region. The possible optical transition in these films is found to be an allowed direct transition. The values of E_g^opt are found to decrease as the CdS content increased. The films with 3 at% CdS content have better decomposition efficiency than undoped TiO₂. The films with 6 at% and 9 at% CdS content have decomposition efficiency comparable to that of undoped TiO₂, although they have lower band gap. The CdS doped TiO₂ could have a better impact on the decomposing of organic wastes.     

Investigation of CdS and CdTe thin films and influence of CdCl2 on CdTe/CdS structure

CdTe/CdS heterojunction solar cell structure has been fabricated using simple, easy and low-cost methods. To fabricate this structure, CdS and CdTe thin films are deposited onto FTO-coated conducting glass substrates by chemical bath deposition (CBD) and electrodeposition method, respectively. The optimized growth conditions are chosen for both CdS and CdTe films by investigating the optical, structural and morphological properties of both the as-deposited and annealed films. Optical measurement showed that CdS films have higher transmittance and lower absorbance, and CdTe films have lower transmittance and higher absorbance in the near infrared region. The band gap of CdS films is estimated to lie in the range 2.29–2.41 eV and that of CdTe films is in the range 1.53–1.55 eV. X-ray diffraction (XRD) study reveals that CdS and CdTe films are polycrystalline with preferential orientation of (1 1 1) plane. Scanning electron microscopy (SEM) study reveals that both films are smooth, void-free and uniformly distributed over the surface of the substrate. Fabricated CdTe/CdS structure showed the anticipated rectifying behaviour, and the rectifying behaviour is observed to improve due to CdCl₂ treatment.     

Third-order optical nonlinearities of lead-free (Na1−xKx)0.5Bi0.5TiO3 thin films

(Na_1−xK_x)_0.5Bi_0.5TiO₃ (NKBT) (x = 0.1, 0.2, and 0.3) thin films with good surface morphology and rhombohedral perovskite structure were fabricated on quartz substrates by a sol-gel process. The fundamental optical constants (the band gaps, linear refractive indices and absorption coefficients) of the films were obtained through optical transmittance measurements. The nonlinear optical properties were investigated by Z-scan technique performed at 532 nm with a picosecond laser. A two-photon absorption effect closely related with potassium-doping content was found in thin films, and the nonlinear refractive index n₂ increases evidently with potassium-doping. The real part of the third-order nonlinear susceptibility χ⁽³⁾ is much larger than its imaginary part, indicating that the third-order optical nonlinear response of the NKBT films is dominated by the optical nonlinear refractive behavior. These results show that NKBT thin films have potential applications in nonlinear optics.     

Preparation and characterization of CdS/Si coaxial nanowires

CdS/Si coaxial nanowires were fabricated via a simple one-step thermal evaporation of CdS powder in mass scale. Their crystallinities, general morphologies and detailed microstructures were characterized by using X-ray diffraction, scanning electron microscope, transmission electron microscope and Raman spectra. The CdS core crystallizes in a hexagonal wurtzite structure with lattice constants of a=0.4140 nm and c=0.6719 nm, and the Si shell is amorphous. Five Raman peaks from the CdS core were observed. They are 1LO at 305 cm⁻¹, 2LO at 601 cm⁻¹, A₁-TO at 212 cm⁻¹, E₁-TO at 234 cm⁻¹, and E₂ at 252 cm⁻¹. Photoluminescence measurements show that the nanowires have two emission bands around 510 and 590 nm, which originate from the intrinsic transitions of CdS cores and the amorphous Si shells, respectively.     

CdS thin films growth by fast evaporation with substrate rotation

CdS thin films were grown by fast evaporation technique combined with substrate rotation. The source evaporation temperature was maintained at 600 °C and the substrate temperature at 350 °C with background pressure of 1.0 m Torr. The substrates were corning glass 2947 with dimension of 1 in. × 1 in. rotate at 500 rpm during the growth. In order to verify the quality of the CdS films, the samples were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM) and optical measurements. The films shown a flat uniformity thickness with growth rate of ∼3.5 nm/s, the orientation was in the cubic-(1 1 1) and hexagonal-(0 0 2) plane in dependence of the growth time, grain size ∼5 nm, roughness uniformity ∼2.7 nm, transmittance in the visible region spectrum ∼80%, energy band gap between 2.39 and 2.42 eV and short circuit photocurrent density (J_SC) losses in the CdS films of 4.7 mA/cm².     

pH dependent interaction of biofunctionalized CdS nanoparticles with nucleobases and nucleotides: A fluorimetric study

The interaction of DNA bases and corresponding nucleotides with CdS nanoparticles (NPs), biofunctionalized by cysteine, has been investigated by absorption and fluorescence spectroscopy. Unique enhancement effect of adenine, in contrast to other nucleobases, on the luminescence of cysteine capped CdS (cys-CdS) NPs at both pH 7.5 and 10.5 was found, the extent of enhancement being much higher at pH 10.5. At the latter pH, the difference optical absorption spectra show development of new peak at 278 nm with corresponding decrease in the absorption of adenine at 260 nm, which is attributed to binding of adenine anion to the CdS surface through N7 of the purine ring. Appearance of a new band at 478 cm⁻¹ and concomitant shift in the C₈-N₇ vibrations to 1610 cm⁻¹ in the FTIR spectra of cys-CdS NPs with adenine also suggest Cd-N7 binding on the particle surface. Amongst various nucleotides, ATP exhibited maximum luminescence enhancement on CdS NPs for a given change in concentration in the micro-molar range at physiological pH. A quantitative correlation between ATP concentration and PL enhancement of CdS NPs has been established, a step which in future might assist in developing new protocols for fluorescence sensing of adenine nucleotides under certain pathological conditions.     

Synthesis,spectral, thermal and optical characterization of benzyltributylammonium trichlorobarium(II) monohydrate crystal

A new nonlinear optical semiorganic crystal, benzyltributylammonium trichlorobarium(II) monohydrate was grown by slow evaporation solution growth method at ambient temperature. The powder X-ray diffraction pattern of the crystal confirms its crystallinity. The absorption spectrum of the material shows a peak at 265 nm and no absorption observed in the entire visible region indicates that the compound can be used as a nonlinear optical material. The optical transmittance spectrum of the grown crystal shows a lower cut-off wavelength at 235 nm with transparency of 88%. Thermal stability of the crystal was studied by thermogravimetry-differential thermogravimetry and differential thermal analyses (TG-DTG and DTA). The differential scanning calorimetry (DSC) analysis shows thermal anomalies in the heating and cooling cycles that indicates the occurrence of a first order phase transition. The various characteristics absorption chemical bands and BaCl₃⁻ vibration were assigned through fourier transform infrared (FTIR) spectral analysis. The second harmonic generation efficiency (SHG) of the grown crystal was analyzed by Kurtz–Perry powder technique using Nd:YAG laser. The dielectric constant and dielectric loss of the compound decrease with increase in frequency.     

Preparation of Ru-loaded CdS/Al-HMS nanocomposites and production of hydrogen by photocatalytic degradation of formic acid

The composite of aluminum-substituted mesoporous silica (Al-HMS) molecular sieve coupled with CdS (CdS/Al-HMS) was prepared by template, ion exchange and sulfurization reactions. The result of low angle XRD patterns showed that the low content of 2.5 wt% CdS is incorporated inside Al-HMS channels. The results of diffuse reflectance UV-visible spectra and fluorescence emission spectra exhibited that the absorption edge and photoluminescence peak for CdS/Al-HMS are blue-shifted about 75 nm and 40 nm in comparison to bulk CdS, respectively. The activities of hydrogen production by photocatalytic degradation of formic acid were evaluated under visible light irradiation (λ ≥ 420 nm) and the CdS/Al-HMS loaded 0.07 wt% Ru showed the highest H₂ evolution at a rate of 3.7 mL h⁻¹ with an apparent quantum yield of 1.2% at 420 nm.     

Nonlinear optical absorption and fluorescence of phosphine-substituted bithiophenes in the violet-blue spectral region

The nonlinear optical absorptions of two 5,5′-bis(diphenylphosphino)-2,2′-bithiophene derivatives, Ph₂(X)P(C₄H₂S)₂P(X)Ph₂ (X = O, 1; S, 2), have been investigated by direct transmission measurement with both picosecond and nanosecond laser pulses from 420 nm to 480 nm. Saturated dichloromethane solutions of 1 and 2 exhibit strong nonlinear optical absorptions in this violet-blue spectral region with that of 2 being stronger at all wavelengths. In the picosecond regime, at 420 nm, the transmittance rapidly falls to 50% when the incident fluence is 0.22 J/cm² for 1 and 0.11 J/cm² for 2. Two-photon absorption appears to be the primary mechanism for this nonlinear absorption. The two-photon absorption coefficients β for 1 (2.1 cm/GW) and 2 (4.4 cm/GM) were obtained by fitting the measurement of transmittance as the function of incident beam intensity at 420 nm. These β values are comparable with some of the best results obtained for organic materials in the green, red and infrared spectral region. Both compounds also show fluorescence with an emission peak at 390 nm for 1 and 400 nm for 2. The fluorescence of 1 is considerably stronger than is that of 2. The combination of the wide band gap and strong fluorescence emission of 1 makes it a promising candidate as a host material for blue organic light emitting diodes.