Proposal of dual-heterodyne-mixing method and application to high-speed waveform measurement using low-speed equipments

A novel method to measure a relative phase between frequency-different optical wavelengths has been proposed and named as Dual-heterodyne-mixing method. The operation principle of the method is represented, where the relative phase is simply described as dc voltage. The operation principle was experimentally confirmed with 0- and π-phase-different optical pairs generated by an intensity modulator. Also, it has been applied for a high-speed signal sensing with a high-resolution amplitude spectrum measurement method. A 12.5 Gbps signal sensing with 1/63 relatively low-speed photodetector (200 MHz) was demonstrated.     

A fiber-optic voltage sensor based on macrobending structure

We propose and demonstrate an optical voltage sensing scheme based on a macrobending optical fiber in a ratiometric power measurement system. This novel approach to sensing has not been utilized before and has the advantage that the sensor involves simple fabrication compared to existing fiber-optic voltage sensors. To prove the feasibility of such a fiber-optic sensor, a sensor for a voltage range from 0∼100 V is demonstrated, with a resolution of 0.5 V. The sensor is robust, linear, and shows a competitive measurement resolution. The sensor can be easily scaled to suit other voltage levels and be effectively combined with optical current sensors.     

反射式光学电压互感器光路建模及偏振误差分析

光路系统的偏振误差极大地制约着准互易反射式光学电压互感器的准确度.借助琼斯矩阵,建立了分立光学器件及光纤熔接点的传输模型,推导出完整的电压互感器光路系统的数学模型.以此模型为基础,对电压互感器中的偏振误差进行了仿真分析.结果表明：光源偏振度、起偏器消光比及起偏器与相位调制器的对轴角度主要影响系统的检测灵敏度|法拉第准直旋光器的旋光角度、法拉第准直旋光器与BGO晶体的对轴角度误差是主要的偏振误差源,影响系统的测量准确度及稳定性|根据电子式电压互感器IEC60044-7 0.2S级标准,法拉第旋光角度误差应该小于1.6°,旋光器与BGO晶体对轴角度误差小于1.85°.该研究对准互易反射式光学电压互感器光路设计和误差抑制具有一定的参考价值和指导意义.     

电光与磁光效应的互补特性及其传感应用

研究了兼有电光效应和磁光效应的晶体内电光与磁光效应的互补特性及其传感应用. 在光强度调制条件下, 晶体中偏振光波的电光调制与磁光调制具有互相补偿的效果, 从而能够使输出光强度保持为一个固定值. 基于这种互补特性, 提出了一种利用单块闪烁锗酸铋(Bi₄Ge₃O₁₂, BGO)晶体的电光补偿型光学电流(磁场)传感器, 其光学传感单元由两个偏振器和一块平行四边形BGO晶体组成. 该晶体自身能够产生π/2的光学相位偏置, 同时兼用作电流传感和电光补偿元件, 通过控制BGO晶体的外加电压, 能够实时补偿被测电流(磁场)变化引起的磁光旋转角和输出光强度的变化, 从而实现电流(磁场)的闭环光学测量. 实验测量了5.0 A范围内的工频交流电流, 所需要的电光补偿电压约为21.2 V/A, 补偿电压与被测电流之间具有良好的线性关系, 其非线性误差低于1.7%.     

反射式光学电压互感器光路建模及偏振误差分析

光路系统的偏振误差极大地制约着准互易反射式光学电压互感器的准确度.借助琼斯矩阵,建立了分立光学器件及光纤熔接点的传输模型,推导出完整的电压互感器光路系统的数学模型.以此模型为基础,对电压互感器中的偏振误差进行了仿真分析.结果表明:光源偏振度、起偏器消光比及起偏器与相位调制器的对轴角度主要影响系统的检测灵敏度;法拉第准直...     

Point-diffraction interferometer for atmospheric adaptive optics in strong scintillation

This paper evaluates the performance of a point-diffraction interferometer for closed-loop adaptive optics. A point-diffraction interferometer was built using a modified Mach-Zehnder set-up. The system was used in closed-loop using a SLM to implement a square, 12 × 12, piston-only segmented corrector with a stroke of ±π. Its performance was tested for the case of atmospheric turbulence aberrations. The investigation showed, through simulation and experiment, that the point-diffraction interferometer worked in closed-loop operation in both uniform intensity and scintillated aberrations. Its robustness in the presence of phase discontinuities makes it a promising option for wavefront sensing in strong scintillation.     

Effects of sulfur content and slab reheating temperature on the magnetic properties of fully processed nonoriented electrical steels

The effects of sulfur content and slab reheating temperature on the magnetic properties of four fully processed nonoriented electrical steels have been investigated. Four slabs of nonoriented electrical steels with sulfur content in the range of 0.0006–0.0126 wt% were reheated to 1100, 1200, and 1300 °C, respectively. Then, they were hot rolled and annealed at 700 °C, cold rolled at the same condition and annealed at 820 °C in the salt bath furnace for 1 min to simulate continuous annealing. The ac core loss, dc hysteresis loss, and ac and dc permeability were measured at 15 kG inductions. It was found that the amount of inclusions in the hot-rolled bands increased with increasing slab reheating temperature and increasing sulfur content in steels. After final annealing, grain sizes of cold-rolled steel sheets decreased with increasing sulfur content and increasing slab reheating temperature. The main preferred orientations in the final annealed steel sheets were (0 1 1) 〈1 0 0〉 and (1 1 1) 〈u v w〉 γ fiber texture. Steel sheets containing 0.0032 and 0.0060 wt% sulfur developed a more stronger (0 1 1)〈1 0 0〉 texture than other steel sheets. However, steel sheets containing 0.0126 wt% sulfur had the weakest (1 1 1)〈u v w〉 texture during slab reheating at temperatures higher than 1200 °C. Both ac core loss and dc hysteresis loss increased with increasing slab reheating temperature and increasing sulfur content in steel sheets. Both ac and dc permeability decreased with increasing slab reheating temperature and increasing sulfur content in steel sheets. If sulfur content decreased from 0.0060 to 0.0032 wt%, there were great improvements in ac core loss, dc hysteresis loss, and ac and dc permeability. However, eddy current loss was almost independent of the sulfur content and slab reheating temperature.     

Fabrication of the slanted electrode matrix on tilting 4.5° (1 1 1) silicon

The slanted low electrode matrix is designed and fabricated on one tilting 4.5° (1 1 1) silicon wafer to reduce the actuating voltage of 8×8 micro-electromechanical systems (MEMS) optical switch matrix. Due to compact size of the upper electrode chip and (1 1 1) silicon anisotropic etching in KOH solution, photomask is designed which is to fabricate the slanted low electrode matrix that can be matched with the upper electrode chip and every slanted low electrode has enough space for actuating cantilever. The experimental results show that all of the applied voltages for the full range of actuating micromirrors of 8×8 MEMS optical switch matrix are in the range of 67.2±0.5 V. It is demonstrated that the fabricated slanted low electrode matrix has good consistency and every slanted low electrode can be precisely aligned with one-to-one corresponding upper electrodes.     

Pockels effect of water in the electric double layer at the interface between water and transparent electrode

We have obtained the first experimental evidence for the Pockels effect of water, which is induced by a high electric field in the electric double layer (EDL) on the water-transparent electrode interface. The electric-field induced energy shift of the visible interference fringes of a 300 nm indium-tin-oxide (ITO) electrode layer is observed, indicating a negative refractive index change at the interface. Numerical calculation reproduces well the experimental observation, showing that the signal mainly originates from water in the EDL. The Pockels constants of water are estimated to be r₃₃ = 5.1 × 100 pm/V and r₁₃ = 1.7 × 100 pm/V. The large anisotropy of the Pockels effect of water is deduced from the incidence angle dependence of the p-polarization signal. At the same time, the ITO shows a blue shift of the band gap in the UV due to the band population effect in the space charge layer. The plasma frequency in the near IR is also expected to increase due to the band population effect, since the ITO has a high doped carrier population close to metal. A negative refractive index change in the ITO space charge layer is induced from both effects, but its effect on the signal is estimated to be much smaller than that of the negative refractive index change of water in the EDL.     

Design strategy for broadband or dual-band ultrathin imaging system

Using reflective multiple-fold approach can reduce bulk and weight compared with large high-quality optical systems and improved resolution and light collection compared with miniature conventional systems. Air-spaced concentric multi-reflection (ACMR) systems, where two reflective surfaces surround a hollow cavity, are useful for extended focal distance, achromatic aberration, useful for inexpensive, lightweight IR imagers and may lead to convenient designs for broadband or dual-band imagers. Design a camera, which spectral response 2?12 μm, with a total thickness of 30 mm, 130 mm effective focal length, ±4.2° FOV, 0.022 mrad resolution and 68 mm effective aperture, 96 mm outer aperture. Application can fit into the hull or wing of a micro-UAV aircraft, which weight and thickness are tightly constrained, for long range surveillance.     

Simple electro-optic technique to generate temporally flat-top laser pulses

A simple technique is presented to generate temporally flat-top shaped laser pulses using electro-optic modulator (Pockels cell). It involves splitting of input laser pulse into two halves of equal intensity and then stacking together with appropriate optical delay to get a temporally flat-top laser pulse. It also allows generation of other pulse shapes by varying the relative intensity, delay, and phase between two halves of the input laser pulse. Temporally flat-top laser pulses of duration ~ 9 ns have been generated using ~ 7 ns duration incident laser pulses from a flash lamp pumped Q-switched Nd:glass laser oscillator. The rise and fall-time of the shaped pulse is limited by speed of electro-optic switch (Pockels cell), which is ~ 2 ns in the present case.     

Superparamagnetic behavior of La0.67Sr0.33MnO3 nanoparticles prepared via sol-gel method

Magnetic nanoparticles of La_0.67Sr_0.33MnO₃ (LSMO) manganite were prepared by sol-gel method. Phase formation and crystal structure of the synthesized powder were examined by the X-ray diffraction (XRD) using the Rietveld analysis. The mean particle size was determined by the transmission electron microscopy (TEM). Infrared transmission spectroscopy revealed that stretching and bending modes are influenced by calcinations temperature. The temperature dependence of the ac magnetic susceptibility was measured at different frequencies and ac magnetic fields in the selected ranges of 40-1000 Hz and 80-800 A/m, respectively. The temperature dependence of ac susceptibility shows a characteristic maxima corresponding to the blocking temperature near room temperature. The frequency dependence of the blocking temperature is well described by the Vogel-Fulcher law. By fitting the experimental data with this law, the relaxation time τ₀=1.7×10⁻¹² s, characteristic temperature T₀=262±3 K, anisotropy energy E_a/k=684±15 K and effective magnetic anisotropy constant k_eff=2.25×10⁴ erg/cm³ have been obtained. dc Magnetization measurement versus magnetic field shows that some of LSMO nanoparticles are blocked at 293 K. The role of magnetic interparticle interactions on the magnetic behavior is also investigated.     

Variable optical attenuator based on a vertical comb drive actuated MEMS micromirror

This letter presents the design, simulation, fabrication, and successful demonstration of a variable optical attenuator (VOA) based on a micromachined micromirror combined with an optical fiber collimator. The micromirror has a size of 500 μm in diameter and a rotational resonance of 4.94 kHz. The micromirror was actuated by vertical comb drive which was fabricated by bulk micromachining process on a silicon on insulator (SOI) wafer. The VOA operates at a low driving voltage of 4.4 V corresponding to the rotation angle of 0.3°. The turn-on and turn-off response time of the VOA are 1.6 ms and 2.74 ms, respectively. Finally, the optical attenuation was measured and an optical attenuation as large as 40 dB was obtained.     

C-V studies on metal-ferroelectric bismuth vanadate (Bi2VO5.5)-semiconductor structure

Ferroelectric bismuth vanadate Bi₂VO_5.5 (BVO) thin films have been successfully grown on p-type Si(100) substrate by using chemical solution decomposition (CSD) technique followed by rapid thermal annealing (RTA). The crystalline nature of the films has been studied by X-ray diffraction (XRD). Atomic force microscopy (AFM) was used to study the microstructure of the films. The dielectric properties of the films were studied. The capacitance-voltage characteristics have been studied in metal-ferroelectric-insulator-semiconductor (MFIS) configuration. The dielectric constant of BVO thin films formed on Si(100) is about 146 measured at a frequency of 100 kHz at room temperature. The capacitance-voltage plot of a Bi₂VO_5.5 MFIS capacitor subjected to a dc polarizing voltages shows a memory window of 1.42 V during a sweep of ±5 V gate bias. The flatband voltage (V_f) shifts towards the positive direction rather than negative direction. This leads to the asymmetric behavior of the C-V curve and decrease in memory window. The oxide trap density at a ramp rate of 0.2 V/s was estimated to be as high as 1.45×10¹² cm⁻².     

Improved frequency response measurement method of half-wave voltage for phase modulator

In this paper, the improvement method of the traditional optical spectrum analyzer (OSA) is demonstrated to measure the half-wave voltage of LiNbO₃ phase modulator with low RF driving. Based on calculating the measured powers ratio of the carrier and first-order side band with optical spectrum analyzer (OSA), the phase modulation index is between 0.5 and 1.43 and the voltage of driving signal is lower than 0.796 V, the accurate characterization of the phase modulator is obtained. By using this method, the half-wave voltage of a LiNbO₃ phase modulator had been measured in the frequency range of 26 GHz. And, our experimental results showed a good agreement between the measured data and those provided by the manufacturer in 9 GHz frequency range. It is an accurate and easy method to measure the half-wave voltages of a phase modulators, especially for measuring high the frequency response.     

Magnetic and optical response of tuning the magnetocrystalline anisotropy in Fe3O4 nanoparticle ferrofluids by Co doping

Co_xFe_3−xO₄ (0?x?0.10) nanoparticles coated with tetramethyl ammonium hydroxide as a surfactant were synthesized by a co-precipitation technique. The Fe:Co ratio was tuned up to x=0.10 by controlling the Co²⁺ concentration during synthesis. The mean particle size, determined by transmission electron microscopy, ranged between 15±4 and 18±4 nm. The superparamagnetic blocking temperature and the magnetocrystalline anisotropy constant of the ferrofluids, determined using ac and dc magnetic measurements, scale approximately linearly with cobalt concentration. We also find distinct differences in the optical response of different samples under an applied magnetic field. We attribute changes in field-induced optical relaxation for the x=0 and 0.05 samples to differences in the anisotropic microstructure under an applied magnetic field.     

Simple sensing head geometry using fibre Bragg gratings for strain-temperature discrimination

In this work, a simple sensing head geometry using fibre Bragg gratings for strain and temperature discrimination is presented. The sensing head geometry consists in one fibre with two FBGs bonded with a dummy optical fibre. Due to this new configuration, different strain sensitivities of the two FBGs are obtained (≈65% difference), while temperature sensitivities remain the same. This difference in strain sensitivities is substantially larger than in all previously reported dual grating sensors. The obtained experimental errors were ±13.48 με and ±2.44 °C, respectively. It is also demonstrated that this new configuration can be used as a temperature-independent strain sensor.     

Temperature-independent optical fiber Fabry–Perot refractive-index sensor based on hollow-core photonic crystal fiber

A novel optical fiber refractive index (RI) sensor, which is based on an intrinsic Fabry–Perot interferometer (IFPI) formed by a section of hollow-core photonic crystal fiber (HCPCF) and standard single mode fibers (SMF), is proposed. The external refractive index is determined according to the maximum fringe contrast of the interference fringes in the reflective spectrum of the sensor. The RI response performance is demonstrated for the measurement of the different RI solutions. The experimental data agree well with the theoretical results. Also the RI resolution and repeatability of ∼1.5 × 10⁻⁵ and ±0.5% in the linear measurement region, are achieved. In addition, the temperature response is tested from 20 °C to 120 °C, which exhibits excellent thermal stability. Therefore, such an HCPCF-based F–P sensor provides a practical way to measure RI with non-temperature compensation.     

Linearization and dispersion tolerable technique for remote access unit in uplink RoF system based on gain-saturated RSOA cascaded EAM

A novel scheme of a remote access unit which is based on an electroabsorption modulator cascaded by a gain-saturated reflective semiconductor optical amplifier is proposed to improve a transmission performance of uplink signal. The cascaded gain-saturated reflective semiconductor optical amplifier plays a role in enhancing linearity of the electroabsorption modulator as well as suppressing dispersion-induced carrier suppression in the uplink transmission using its nonlinear gain property. In the proposed scheme, carrier-to-interference ratio of transmitted 10-GHz band uplink signal was improved by 10.7 dB and the dispersion-induced carrier suppression of 5.65-GHz RF carrier was greatly mitigated by 33.4 dB through the 75.6-km optical link.