锥形空心银波导的聚焦特性

利用时域有限差分(FDTD)方法数值演示了一种能光学引导和聚焦激光的锥形空心银波导,数值模拟结果表明这种锥形空心银波导能把激光聚焦成一个极小的、直径只有1 μm、强度高度局域性的光斑.对锥形波导能光学引导和聚焦激光的物理机理作了分析和探索,并进一步探讨了激光倾斜入射、波导几何结构对锥形波导聚焦特性造成的影响,这些研究结果对于锥形光学的应用、快点火或产生高能带电粒子中锥靶结构的最佳设计具有重要的参考价值. 关键词： 锥形波导 聚焦特性 时域有限差分     

Surface treatment with linearly polarized laser beam at oblique incidence

An effective method for surface heat treatment with 10.6 μm linear polarized laser beam at oblique incidence is reported. A circular focused laser spot on the workpiece surface, simultaneously with 2.2–4 times increasing of the absorption are obtained in the 70–80° range of the incidence angle. The main element of the experimental setup is the astigmatic focusing head which focalize the laser beam into an elliptical spot of ellipticity >3 at normal incidence. At a proper incidence angle (obtained by the focusing head tilting) the focused laser spot on the work piece surface gets a circular form and p-state of polarization is achieved.We performed laser heat treatment (transformation hardening, surface remelting) of the uncoated surface, as well as the alloying and cladding processes by powder injection. An enhancement of the processing efficiency was obtained; in this way the investment and operation costs for surface treatment with CO₂ laser can be significantly reduced. Several technical advantages concerning the pollution of the focusing optical components, powder jet flowing and reflected radiation by the work piece surface are obtained.     

The characteristics of laser micro drilling using a Bessel beam

A Bessel beam is suitable for laser micro-fabrication because it possesses both a micron-sized focal spot and a deep focal depth. As the influence of focusing aberrations is much smaller than that of a convex lens, the generation of a Bessel beam using an axicon is very practical. In the case of laser micro drilling of austenitic stainless steel with a Bessel beam, suitable processing conditions were investigated. The threshold fluence to make a through hole increased with an increase in the sample thickness. For samples with the same thickness, the threshold fluence increased with an increase in the crossing angle. A small crossing angle Bessel beam can drill a deep hole with a small threshold fluence. A through hole with a diameter smaller than 10 μm can be made on a stainless steel sheet 20 μm thick by using a Bessel beam with a large crossing angle. The taper of the hole drilled with the Bessel beam is smaller than that with the focused beam from the convex lens. PACS 52.38.Mf; 42.62.Cf; 42.79.Bh     

Micro-ablation on silicon by femtosecond laser pulses focused with an axicon assisted with a lens

Micro-ablation of crystalline silicon was performed by irradiating a silicon substrate with femtosecond laser pulses of wavelengths 786 nm or 393 nm focused using a conical axicon assisted with a convex lens. Focusing the laser beam close to the tip of the axicon by means of the lens significantly improved the efficiency of concentration of laser pulse energy at the central spot of the resulting Bessel-Gaussian intensity distribution. As a result, micron-sized holes were formed with the diameter determined by the ablation threshold in the calculated fluence profile. It is possible to predict hole size from the laser pulse energy and the wavelength. Crystalline particles, a few tens of nanometers in size, were formed near the ablated zone.     

Tapered hollow waveguide for focusing infrared laser beams

A tapered hollow waveguide that can focus a laser beam into a small beam spot is proposed for medical and dental applications. We fabricated hollow tapered optics by using a traveling torch, and the shape was formed as a precise linear taper. For a hollow taper tip with input and output diameters of 700 and 200 microm, respectively, the insertion loss is as small as 0.7 dB in a 10 mm long taper. The hollow taper optic producing a 200 microm spot withstands input energy of 100 mJ. Because a focusing lens is unnecessary at the output end, the laser beam can be introduced into a deep and narrow spot with these tapered optics.     

空心锥状双高斯光束传输特性研究

建立了空心锥状双高斯光束的模型.在空心高斯光束模型的基础上,由初始光场的光强分布,利用柱坐标下的柯林斯公式,导出了空心锥状双高斯光束经过傍轴光学系统的解析传输变换式由传输变换式计算分析了空心锥状双高斯光束在自由空问的可控传输特性,及在1,10和60 m的截面光环的光强分布.用KNbO3双轴晶体进行实验,获得了空心锥状双高斯光束,外锥折射的锥角等于入射光会聚角.实验表明,当空心光束处于锥状发射状态时,空心光束的光环内黑斑面积随传输距离的增加而增加,实验结果与模型吻合较好.该研究为进一步设计制备基于空心锥状舣高斯光束的新型激光元件提供了理论依据和设计参量.     

Generation of thin and hollow beams by the axicon with a large open angle

We propose a method to produce diffraction-free thin and hollow beams. The method is based on Laguerre-Gaussian (LG) beams incident on a large open-angle axicon. We use the vector diffraction integrals and stationary phase method to deduce a simple and analytical formula of the propagating field of the linearly polarized LG beams through an axicon. The numerical results show that the hollow beams of whose diameter is in the order of the wavelength can be obtained by using the axicon with the refractive index n = 2 and the open angle α = 25°. These diffraction-free thin and hollow beams may be very useful to accurately trap and manipulate atoms. However, when the open angle is over large, the conversion efficiency from the LG beam to the diffraction-free hollow beam will decrease obviously.     

Multi-wavelength laser sensor for intruder detection and discrimination

An intruder detection and discrimination sensor with improved optical design is developed using lasers of different wavelengths to demonstrate the concept of discrimination over a distance of 6 m. A distinctive feature of optics is used to provide additional transverse laser beam scanning. The sample objects used to demonstrate the concept of discrimination over a distance of 6 m are leaf, bark, black fabric, PVC, wood and camouflage material. A camouflage material is chosen to illustrate the discrimination capability of the sensor. The sensor utilizes a five-wavelength laser combination module, which sequentially emits identically-polarized laser light beams along one optical path. A cylindrical quasi-optical cavity with improved optical design generates multiple laser light beams for each laser. The intensities of the reflected light beams from the different spots are detected using a high speed area scan image sensor. Object discrimination and detection is based on analyzing the Gaussian profile of reflected light at the different wavelengths. The discrimination between selected objects is accomplished by calculating four different slopes from the objects' reflectance spectra at the wavelengths 473 nm, 532 nm, 635 nm, 670 nm and 785 nm. Furthermore, the camouflage material, which has complex patterns within a single sample, is also detected and discriminated over a 6 m range by scanning the laser beam spots along the transverse direction.     

Fibre-end micro-lens system for endoscopic erbium-laser surgery applications

A sapphire micro-lens system in combination with a zirconium-fluoride (ZrF₄) fibre has been designed and constructed as a surgical tool for focusing Er:YAG-laser radiation. It both refocuses the laser radiation transmitted through a 350 µm core fibre to a spot diameter of 570 µm at a working distance of 7.6 mm, and protects the distal fibre end from damage. An accurate and uncomplicated visualization of the focus position of the erbium-laser beam is realized by coupling a HeNe aiming laser into the cladding of the fibre. In vitro cutting experiments reveal the high cutting precision with minimal thermal damage of the surrounding tissue and the high damage resistance of the system. It may render the use of the erbium laser possible in a wide range of endoscopic applications.     

Studies of craters’ dimension for long-pulse laser ablation of metal targets at various experimental conditions

Long pulse laser shots of the PALS iodine laser in Prague have been used to obtain metal target ablation at various experimental conditions. Attention is paid mainly to the dependencies of the crater diameter on the position of minimum laser-focus spot with regard to the target surface, by using different laser wavelengths and laser energies. Not only a single one, but two minima, independently of the wavelength, of the target irradiation angle and of the target material, were recorded. Significant asymmetries, ascribed to the non-linear effects of intense laser beam with pre-formed plasma, were found, too. Estimations of ejected mass per laser pulse are reported and used to calculate the efficiency of laser-driven loading. Results on metal target ablation and crater formation at high intensities (from 2 × 10¹³ to 3 × 10¹⁶ W/cm²) are presented and compared. Crater depth, crater diameter and etching yield are reported versus the laser energy, in order to evaluate the ablation threshold fluence.     

内窥镜的红外激光传输用柔性空芯光纤的研制

通过理论计算确立了多功能介质-金属结构空芯光纤的结构参量,优化了液相镀膜法的有关条件,明确了具体制作参量。制作了以聚碳酸酯毛细管为基管的,高柔韧性的,可同时低损耗传输红外目标波长激光和可见导航光红外的空芯光纤。对光纤传输性能进行了测试。在2.94μm波长的Er∶YAG和0.63μm波长的红色半导体激光器的直线损耗分别为0.4 dB/m和3 dB/m。组装在医疗内窥镜中的柔性空芯光纤,在先端以0.9 cm半径135°角弯曲时,对Er∶YAG激光仍有近70%的传输效率;绿色导航光在内窥镜中的的损耗值为11 dB,绿色指示点在内窥镜的视窗中清晰可见。结果表明此种光纤在内窥镜的激光传输方面有重要的应用价值。     

Laser-generated surface acoustic waves in a ring-shaped waveguide resonator

Surface acoustic wave (SAW) waveguide resonator is formed by a ring-shaped strip of copper 10 μm wide and ∼130 μm in diameter embedded into a 0.8 μm thick layer of silica on a silicon wafer. SAWs are excited at one side of the copper ring by a short laser pulse focused into a spatially periodic pattern and detected via diffraction of the probe laser beam overlapped with the excitation spot. SAW wavepackets with central frequency 460 MHz travel around the ring and are detected each time they make a full circle and pass trough the probe spot. Potential applications of ring resonators for SAWs are discussed.     

Effect of spot size on cone formation in a XeCl laser ablation of polyethersulfone films

Radiation from the UV excimer lasers, with the fluence above the ablation threshold, can etch the polymer surfaces by photoablation. In some cases different microstructures may appear on the surface during the laser ablation. In this paper the effect of the laser spot size on the cone formation on polyethersulfone films has been investigated. The experiments have been performed with a XeCl laser at the wavelength of 308 nm and at the fluences of 70 and 100 mJ/cm² at air. For the investigation of the effect of the laser spot size on cone formation, the samples were irradiated at two different laser spot sizes of w₁ and w₂ = 0.1 w₁. The morphology of the processed surface was studied by scanning electron microscopy (SEM). It has shown that the shape, size and density of cones change with the change of the laser spot size. Also, the number of pulses and the pulse repetition rate which are needed for threshold of cone formation are affected by the laser beam spot size on the surface.     

Fabrication of highly ordered CuInSe2 films with hollow nanocones for anti-reflection

Highly ordered CuInSe₂ films with hollow nanocones were fabricated by electron beam evaporation and nanospheres lithograph. From the AFM analyses, polystyrene nanospheres with diameter of 220 nm are assembled regularly on glass substrates. After reaction ion etching under different powers and residues removal, different and new surface morphologies of substrates have been obtained, such as smooth nanocones and hollow nanocones. The diffuse reflection spectra demonstrate that films on the substrates with periodic nanopatterned structure have less reflection over wavelengths ranged from 200 nm to 2500 nm due to light trapping. Especially, reflection for hollow nanocone arrays has the larger suppression value than nanocone-patterned films, which proves that surface pattern of hollow nanocones has better anti-reflection effect. Furthermore, while hollow depth increases from 6 nm to 9 nm, its optical antireflective effect becomes remarkable. These results could yield new options for solar-cell design with higher energy conversion efficiency.     

锥形透镜光纤聚焦特性研究

锥形透镜光纤(TLF)是实现光纤与平面光波光路(PLC)芯片高效耦合的核心元件。了解和掌握其聚焦特性是指导平面光波光路尾纤封装技术的关键。给出了表征锥形透镜光纤聚焦特性的两个参量出射光斑直径和远场发散角的理论分析模型,其误差小于1.14%;采用光束传播法数值模拟了锥形透镜光纤中的光波传输和模斑的演化,确定了锥形透镜光纤端面出射光斑的大小;优化锥形透镜光纤结构参量为:拉锥长度300μm,锥角0.733°,透镜曲率半径13.485μm;建立了基于数字摄像机的锥形透镜光纤出射光场测试系统,提出了物理光学反向推演法,计算出锥形透镜光纤聚焦光斑尺寸和远场发散角。理论与实验结果有着良好的一致:对于相同结构参量的锥形透镜光纤,实验反推法得到的出射光斑尺寸与理论值相比误差为3.15%,远场发散角误差为3.67%。     

Analysis of materials modifications caused by UV laser micro drilling of via holes in AlGaN/GaN transistors on SiC

Pulsed UV laser drilling can be applied to fabricate vertical electrical interconnects (vias) for AlGaN/GaN high electron mobility transistor devices on single-crystalline silicon carbide (SiC) substrate. Through-wafer micro holes with a diameter of 50-100 μm were formed in 400 μm thick bulk 4H-SiC by a frequency-tripled solid-state laser (355 nm) with a pulse width of ≤30 ns and a focal spot size of ∼15 μm. The impact of laser machining on the material system in the vicinity of micro holes was investigated by means of micro-Raman spectroscopy and transmission electron microscopy. After removing the loosely deposited debris by etching in buffered hydrofluoric acid, a layer of <4 μm resolidified material remains at the side walls of the holes. The thickness of the resolidified layer depends on the vertical distance to the hole entry as observed by scanning electron microscopy. Micro-Raman spectra indicate a change of internal strain due to laser drilling and evidence the formation of nanocrystalline silicon (Si). Microstructure analysis of the vias’ side walls using cross sectional TEM reveals altered degree of crystallinity in SiC. Layers of heavily disturbed SiC, and nanocrystalline Si are formed by laser irradiation. The layers are separated by 50-100 nm thick interface regions. No evidence of extended defects, micro cracking or crystal damage was found beneath the resolidified layer. The precision of UV laser micro ablation of SiC using nanosecond pulses is not limited by laser-induced extended crystal defects.     

圆柱体的空间圆锥光反射、折射与衍射

用准直或会聚激光束倾斜照射圆柱体时,其反射光、透射光(柱体透明时)、衍射光(柱体较细时)的叠加将形成以光束入射点为顶点的空间圆锥形光面(空间光锥),并且在垂直于柱体轴线方向的观察平面上投影成一圆形光环.空间光锥的形成与所选圆柱体材料及其粗细无关,只要其表面具有一定反射能力即可.空间光锥的锥角等于入射光束主光轴与圆柱体轴线夹角的2倍,与圆柱体和照射光束的直径大小及光波长无关.给出了对光纤及不同直径大小的玻璃和金属圆柱体的实验观察结果,并利用矢量图解法对其进行了详细地理论分析.进而得出,通常所谓单丝衍射图样,实际上是细丝的衍射和其表面的反射光场的叠加图样,对于透明细丝,还包括其透射光场的贡献.圆柱体的这种空间圆锥光反射和衍射原理有可能用于光束定位、成形、表面检测以及三维面形测量等 关键词： 圆柱体 空间光锥 投影光环     

Light driven self-drilling in glasses

It is shown that ArF laser beam may act as effective driller producing in fuzed quartz micron radius channel up to 1 cm long while diameter of light spot is few millimeters. Drill formation is accompanied by compaction effect in the drill walls therefore material is not thrown out the channel.     

Design of laser interferometric system for measurement of gear tooth flank

A laser interferometric system (LIS) based on oblique incidence and phase shifting technique has been designed for the measurement of gear tooth flank. For a spur involute gear with a module of 2.0, 60 teeth, and a 20-mm facewidth, some critical parameters of the LIS are calculated, the oblique incidence angle is 84.5°, the beam diameter is 20 mm, and the focal length of imaging lens is 100 mm, and the resolution of CCD camera is 1360 × 1024 pixels. To test the capability of the designed LIS, the numerical simulation is done for the LIS. The actual LIS is built on an optical platform and the experiment is carried out. Both interference fringe patterns from the numerical simulation and the actual experiment are good and coincident with each other, which show the designed LIS is feasible.     

四瓣高斯光束的Gyrator变换性质和矩形空心光束的产生

基于Gyrator变换,推导了四瓣高斯光束场分布的解析表达式,研究了四瓣高斯光束通过Gyrator变换后的光强分布和相位分布.结果表明:在Gyrator变换过程中,四瓣高斯光束能够转换为具有光涡旋的矩形空心光束,在获得矩形空心光束时其四顶角处光束强度最强,而四条边上的光束强度分布几乎是均匀的.对影响矩形空心光束强度和相位分布的光束参数和变换角进行了详细的分析,发现光束阶数不同,产生不同类型的空心光束;Gyrator变换的变换角则影响空心光束能量分布;空心光束亮环的大小由四瓣高斯光束的束腰宽度决定,束腰宽度越大,矩形空心光束的宽度越小.