Simultaneous all-optical multi-channel RZ and CSRZ to NRZ format conversion

We propose and demonstrate multi-channel all-optical return-to-zero (RZ) and carrier-suppressed RZ (CSRZ) to non-return-to-zero (NRZ) format conversions using a same fiber delay-interferometer (DI). The conversions are based on simultaneous constructive interference induced by the periodical comb-like filtering characteristic of the DI. By using a DI with free spectral range of 40 GHz, 8 channel RZ and CSRZ signals at 20 Gb/s can be converted to corresponding NRZ signals at the same time. Furthermore, a duplicate output can be obtained for multi-channel CSRZ input. Bit error ratio measurements show 4 and 3.5 dB penalties for the proposed multi-channel RZ and CSRZ to NRZ conversions respectively. Further transmission for the converted NRZ signals verifies the good performance of the proposed all-passive multi-channel format converter. The potential of multi-channel RZ signals with mixed duty-cycle to NRZ conversions is also investigated.     

Multi-wavelength conversion at 10 Gb/s using cross-phase modulation in highly nonlinear fiber

In this paper we demonstrate a technique of signal wavelength conversion via cross-phase modulation (XPM)-induced nonlinear coupling among a 10 GHz return-to-zero (RZ) signal and a continuous wave (CW) carrier co-propagating in dispersion-shifted (DS) highly nonlinear fiber (HNLF). The wavelength conversion bandwidth up to ±20 nm was achieved experimentally and potential extension was verified by numerical simulations. The principle can easily be extended to 40 Gb/s and used as polarization insensitive all-optical wavelength converter.     

基于半导体光放大器四波混频效应的多种调制格式的波长转换实验

实验报道了利用半导体光放大器(SOA)的四波混频(FWM)效应实现多种码型的波长转换.其中对于非归零(NRZ)信号实现了从单信道到三信道的多波长转换.调制速率从10 Gb/s到40 Gb/s均实现多波长转换.对于归零(RZ)信号分别实现了20 Gb/s和40 Gb/s的RZ格式的波长转换和40 Gb/s的载波抑制归零(CSRZ)格式的波长转换,利用光纤布拉格光栅(FBG)作为带陷滤波器消除共轭光和抽运光之间的串扰.对于非归零差分相移键控(NRZ_DPSK)信号分别实现了20 Gb/s和40 Gb/s的波长转换,利用实验室自制的光纤延时干涉仪进行NRZ-DPSK信号的解调.基于FWM效应的转换光的输出消光比大于7 dB,转换后消光比退化约为3 dB.     

All-optical NRZ-OOK-to-RZ-OOK format conversions with tunable duty cycles using nonlinear polarization rotation of a semiconductor optical amplifier

We experimentally demonstrate an all-optical 10 Gb/s format conversion from non-return-to-zero (NRZ) on-off-keying (OOK) to return-to-zero (RZ)-OOK with tunable duty cycle in the whole C-band using nonlinear polarization rotation (NPR) arising in an semiconductor optical amplifier (SOA). The experimental results show that, by tuning the polarizer at the SOA output, an RZ signal with tunable duty cycle from 33% to 66% could be obtained with an extinction ratio(ER) over 10 dB. In addition, we show that the NRZ-to-RZ conversion with duty cycle of 33-66% can be obtained with less than 1 dB power penalty at the bit error ratio (BER) of 10⁻⁹. The device can facilitate the cross-connection between optical transmission networks employing different modulation formats.     

Simultaneous multichannel NRZ-to-RZ format conversion of 4-ASK signal based on phase-intensity hybrid modulation and dispersion compensation fiber

We propose and investigate a novel technique to realize non-return-to-zero （NRZ） to return-to-zero （RZ） format conversion of a multichannel 4-ary amplitude shift keying （4-ASK） signal. The proposed format converter composed of two modulators and a dispersion compensating fiber （DCF） is theoretically inves-tigated using numerical simulation as basis. Research shows that a 4-channel 20-Gb/s NRZ-4-ASK signal can be converted to a RZ-4-ASK signal simultaneously without wavelength shifting and signal quality degradation, with the converted signal multiplexed to 40 Gb/s.     

40 Gb/s all-optical logic NOR and OR gates using a semiconductor optical amplifier: Experimental demonstration and theoretical analysis

We experimentally and theoretically demonstrate 40 Gb/s all-optical logic NOR and OR gates based on a semiconductor optical amplifier (SOA) and a blue shifted optical bandpass filter (OBF). Two kinds of data formats are discussed, namely return-to-zero (RZ) format and nonreturn-to-zero (NRZ) format. The logic NOR and OR functions of RZ format are realized at the OBF detuning of −0.22 nm and −0.44 nm, respectively. The logic NOR function of NRZ format is realized at the OBF detuning of −0.24 nm. The simulation is in good agreement with the experimental results when the linewidth enhancement factor is 5.5. The simulation also shows that the SOA with large linewidth enhancement factor is preferred to achieve NOR and OR functions with good performance. The input data signal is of good pulsewidth-tolerance for NOR function, whereas not for OR function. The high Q factor could be obtained at narrow pulses injection.     

自启动的非归零/归零码和光电时钟信号发生器及码型转换

采用双波长注入一包含伪随机码发生器与相位调制器的光电振荡器可以同时得到非归零(NRZ)码,归零(RZ)码以及光,电时钟信号输出。该方案使用了光域耦合的双环路结构,在不增加有源器件的条件下实现边模抑制。相位调制器用于反馈调制并同时实现占空比可调的非归零码到归零码的转换。双波长的注入排除了编码信号在振荡器中引入的非时钟频率成分。实验给出了10 Gb/s工作速率下的结果,得到了抖动为637 fs的光信号输出。转换得到的归零码信号占空比约为33%。输出电时钟信号的相位噪声在频偏10 kHz处为-109 dBc/Hz,边模抑制比为58 dB。     

Optical clock recovery with dual-wavelength output from degraded RZ and NRZ signals

A novel scheme to implement clock recovery from degraded signals is proposed and demonstrated based on an optoelectronic oscillator and a dual-wavelength mode-locked fiber ring laser with distributed dispersion cavity. The scheme can obtain wavelength-tunable optical clocks at two wavelengths, which is highly desirable for composite optical logic gates, cascaded optical signal processing modules or optical signal processing modules that need synchronized pulses at multiple wavelengths. In addition, the scheme can operate in both RZ and NRZ systems. The feasibility of the method is demonstrated by an experiment, in which dual-wavelength 10-GHz optical clock with a timing jitter less than 170 fs is obtained from 10-Gb/s degraded RZ and NRZ signals. The optical clocks can be tuned from 1530 to 1565 nm.     

Experimental study of SOA-based NRZ-to-PRZ conversion and distortion elimination of amplified NRZ signal using spectral filtering

We experimentally study both reshaping of nonreturn-to-zero (NRZ) signal and NRZ to pseudoreturn-to-zero (PRZ) format conversion based on self-phase modulation of a semiconductor optical amplifier (SOA) and detuning an optical bandpass filter (OBF). When an OBF with 1 nm bandwidth is blue shifted by 0.8 nm, the distortion of the amplified NRZ signal at 10 Gbit/s is shown to be eliminated completely. When an OBF with 0.32 nm bandwidth is red shifted by 0.42 nm from the carrier frequency, NRZ-to-PRZ conversion at 10 Gbit/s is obtained. A holding beam is used to suppress the SOA noise and improve the output extinction ratio (ER). The output ER of both the reshaped NRZ and the converted PRZ is larger than 10 dB when the signal wavelength is longer than 1540 nm, and an input power dynamic range from −7 dBm to 2 dBm is obtained at a signal wavelength of 1563.6 nm. The average power of the reshaped NRZ signal is about 3 dBm at an input power dynamic range of 13 dB. The amplitude fluctuation of the converted PRZ signal is around 1.6 dB.     

Optimisation of 40 Gb/s wavelength converters based on four-wave mixing in a semiconductor optical amplifier

The optimum operating powers and wavelengths for a 40 Gb/s wavelength converter based on four-wave mixing in a semiconductor optical amplifier are inferred from experimental results. From these measurements, some general rules of thumb are derived for this kind of devices. Generally, the optimum signal power should be 10 dB lower than the pump power (−16 dB conversion efficiency) whereas the wavelength separation between the signal and the pump carrier should not be lower than about four times the signal bitrate (1.3 nm for 40 Gb/s RZ signals).     

Comparative investigation and suitability of various data formats for 10 Gb/s optical AWG multiplexer and AWG demultiplexer based transmission links

In this paper, we have analyzed the performance and feasibility for the metropolitan area network based on arrayed waveguide grating (AWG) multiplexers and arrayed waveguide grating (AWG) demultiplexers operating at the bitrate of 10 Gb/s. In the network, the data is successfully transmitted to a distance of 50 km with a very low BER of 1 × 10⁻⁴⁰ thus improving the performance over AWG star based networks. Here, we have observed that arrayed waveguide gratings based multiplexers and demultiplexers for WDM applications prove to be capable of precise multiplexing and demultiplexing of a large number of channels with relatively low losses. This paper also presents the comparative investigation and suitability of various data formats like NRZ Rectangular, NRZ Raised cosine, RZ Rectangular, RZ Raised cosine and RZ super Gaussian for optical transmission link. It has been shown that RZ Raised cosine yields the highest value of Q, good eye opening and lowest BER.     

Investigation of data format conversions based on MZI-SOA

Employing a Mach-Zehnder Interferometer (MZI), this paper describes simulation demonstration of an all-optical scheme for data format conversion between non-return-to-zero (NRZ) and return-to-zero (RZ). Data format conversion between NRZ and RZ at 120 Gb/s has been simulated for the first time using an MZI. In addition, we have proposed for the first time data format conversion from NRZ to RZ by using a single SOA in an MZI.     

基于PPLN波导中倍频与差频效应的全光波长转换

对准相位匹配的铌酸锂光波导中基于倍频与差频级联二阶非线性效应的全光波长转换进行了研究.在建立理论模型的基础上,分别对单脉冲以及序列光脉冲的波长转换过程进行了数值模拟,并对转换过程中的走离现象以及脉冲延迟进行了分析.模拟结果表明信号光与抽运光脉冲非同步输入的情况下可以克服走离效应的影响,得到更好的转换效率.另外,在抽运时钟脉冲的驱动下,输入的40 Gb/s的NRZ信号光可以转换为RZ转换光,且波形较好.     

Comparative investigation and suitability of various data formats for 10 Gb/s optical soliton transmission links at different chirps

This paper presents the comparative investigation and suitability of various data formats for optical soliton transmission links at 10 Gb/s for different chirps (−0.7 to 0.7). Here the investigations focused on data formats: NRZ, RZ soliton, RZ raised cosine and RZ super Gaussian. The comparative results and suitability of data formats is based on various performance measures such as Q-factor, eye opening, BER and jitter. It has been indicated that RZ super Gaussian yields the highest value of Q (34.08 dB), good eye opening and lowest BER.     

Improving the Performance of All-Optical Wavelength Converters Using Fiber Gratings

We show that spectral filtering using a fiber Bragg grating as an optical discriminator improves the performance of semiconductor optical amplifier (SOA) wavelength converters. This technique increases the operation speed and reduces the data patterning effect of SOAs for non-return-to-zero (NRZ)operation. For return-to-zero (RZ) operation the fiber grating increases extinction ratio and preserves the data polarity. We use this technique to obtain error-free wavelength conversion of NRZ data at 10 Gb s in an SOA with 6 GHz dynamic bandwidth. We also use the SOA fiber grating to convert RZ data at 10 Gb s and show that the converted pulses can propagate error free over 20,000 km in a dispersion-managed system.     

基于光子晶体光纤中双抽运四波混频效应的非归零到归零码型转换实验研究

提出并实验证实了利用色散平坦高非线性光子晶体光纤中双抽运四波混频效应实现非归零 (NRZ)到归零(RZ)码型转换的新方案, 将一束NRZ信号光与两束同步时钟脉冲光同时注入光子晶体光纤, 通过双抽运四波混频效应产生两个闲频光, 经过光学滤波后即可完成单到双全光NRZ-RZ码型转换. 与基于常规单抽运四波混频效应的码型转换方式相比, 本设计方案由于采用了双抽运四波混频效应, 因此具有双路组播信号波长可彼此独立选取的优点. 分析了码型转换器的波长调谐性及对输入光功率波动的容忍性, 得到转换信号的最优消光比和Q 因子分别为15 dB和5.4. 研究结果表明, 本方案既具有对比特率和调制格式透明的优点, 又避免了使用单抽运四波混频效应进行码型转换时两路组播信号波长相互制约的弊端, 且实现了全光波长转换和波长组播功能. 关键词： 码型转换 四波混频 双抽运 光子晶体光纤     

可调马赫-泽德干涉仪型NRZ到PRZ全光码型转换器

研制了一种基于光纤型马赫-泽德干涉仪的全光码型转换器.通过对工作温度的控制,实现了NRZ码到PRZ码的转换.分析了实现NRZ到PRZ码型的转换原理,讨论了干涉仪的结构设计.在10 Gb/s和20 Gb/s的码型转换实验中,得到较好的PRZ信号眼图.光谱分析表明,转换后的PRZ码包含了丰富的时钟分量,达到了理想的转换结果.结果表明,这种简单的光纤型非对称马赫-泽德干涉仪可以实现NRZ到PRZ的转换,并可以保持输出结果的稳定性.     

Utilization of four WDM channels with signal remodulation of OFDM-QAM for 10 Gb/s uplink passive optical networks

In this investigation, we experimentally investigate an extended reach (ER) time-division-multiplexed passive optical network (TDM-PON) using four wavelength-multiplexed channels to achieve 16 Gb/s downlink and 10 Gb/s uplink traffic. Each downlink signal uses the highly spectral efficient 4 Gb/s OFDM-QAM, and each uplink signal is generated by signal remodulating the downlink signal via a reflective semiconductor amplifier (RSOA) at 2.5 Gb/s non-return-to-zero (NRZ). In addition, the performance of the proposed ER TDM-PON has also been analyzed and discussed.     

Optimal design of 32 channels spectrum slicing WDM for optical fiber access network system

In this article, the spectrum sliced dense wavelength division multiplexed passive optical network (SS-DWDM–PON) has been investigated as a power efficient and cost effective solution for optical access networks. In this work an AWG demultiplexer is used to operate as slicing system. The high speed SS-DWDM system has been realized and investigated for 32 channels with data rate up to 3 Gb/s using broadband ASE source (LED). The 3 Gb/s signals both non-return-to-zero (NRZ) and return-to-zero (RZ) were demonstrated in 40 km optical fiber link with BER < 10⁻¹². The results obtained here demonstrate that SS-DWDM is well suited for Fiber-to-the-Home (FTTH) network.     

A novel optical picosecond-duration NRZ-to-RZ format converter with simultaneous wavelength multicasting using a single-stage Mach–Zehnder modulator

We propose a novel and simple scheme to achieve NRZ-to-RZ format conversion and simultaneous wavelength multicasting based on a single-stage dual-arm electro-optic Mach–Zehnder modulator (MZM) and a short single mode fiber (SMF). The format conversion and wavelength multicast process are achieved by chirp compensation under the condition of generation of optical flat frequency comb. 40 Gb/s NRZ-to-RZ conversion with one-to-five multiple-wavelength channel multicasting and transmission of the NRZ and the converted signals over 200 km dispersion-managed fiber-link are successfully demonstrated by numerical simulation. Research results show that 40 Gb/s 2 ps RZ signal with wavelength-preserving can be obtained after format conversion. The converted RZ signal presents good transmission performance and can easily be multiplexed to 160 Gb/s using optical time division multiplexing (OTDM) technology. All the multicast channels can be error free after 50 km transmission. Besides, the conversion operation can also greatly reduce the timing jitter of the degraded NRZ signal due to the retiming function of the proposed scheme.