倾斜光纤光栅溶液折射率传感器的实验研究

根据倾斜光纤光栅(TFBG)和表面镀金的TFBG传感器测量折射率的基本原理,通过OptiGrating软件模拟了不同浓度溶液下TFBG的透射谱和芯层模与某阶包层模耦合引起的谐振峰,初步得出了TFBG各阶包层模随着外界折射率的增大而向右偏移、在一定的传感范围内中心波长与外界折射率呈线性关系的结论。用小型离子溅射仪对TFBG镀45 nm厚度左右的金膜,并用扫描电镜在微观上观察镀膜效果。通过不同浓度下的NaCl溶液、MgCl₂溶液、CaCl₂溶液实验,对比研究了裸TFBG和镀金TFBG传感器对溶液折射率的传感特性。从而验证了模拟仿真得出的结论并定量分析得知：镀金后具有表面等离子体共振的TFBG溶液折射率灵敏度大于500 nm·RIU-1,而裸TFBG为2 nm·RIU-1左右,大约提高了200～300倍,且在一定范围内中心波长与溶液折射率的线性拟合度都在0.99以上。     

不同包层直径的倾斜光纤光栅折射率传感特性

倾斜光纤光栅的透射谱中有纤芯模和大量的包层模,它们具有与布拉格光栅相同的温度特性.利用HF酸腐蚀的方法得到具有不同包层直径的倾斜光纤光栅,研究了其对外界折射率的传感特性.结果表明,外界环境折射率在1.333～1.4532之间变化时,同一直径倾斜光纤光栅的高阶包层模的敏感性要比低阶包层模强;随着包层直径的减小,包层模的敏感性增强,且在折射率比较高的环境中有更高的敏感性.因此,利用倾斜光纤光栅的温度特性不仅可以解决温度交叉敏感问题,而且通过小同的腐蚀程度能定制所需要的灵敏度,以实现对环境折射率的高灵敏度测量.该办法可应用于对生物和化学等高灵敏度传感领域的各种溶液进行实时监控.     

Temperature and strain discrimination using a single tilted fibre Bragg grating

A fibre optic sensor capable of discriminating between temperature and strain, using a single fibre Bragg grating, is presented. The technique exploits the core-cladding mode coupling of a tilted fibre Bragg grating (TFBG). The core and cladding modes exhibit different thermal sensivities, while the strain sensivities are approximately equal. Monitoring the core-core mode coupling resonance and the core-cladding mode coupling resonance of the TFBG spectrum allows the separation of the temperature and strain induced wavelength shifts.     

Lateral force sensor based on a core-offset tilted fiber Bragg grating

A novel lateral force sensor based on a core-offset tilted fiber Bragg grating (TFBG) is proposed and experimentally demonstrated. The lateral force is determined by the differential reflected powers between the cladding mode and Bragg mode in the TFBG. The sensors respond monotonically with the lateral force increasing from 0 to 1.75 N. The sensitivity of such a core-offset TFBG sensor can be tailored by choosing different core-offset values. The simple differential power detection method makes the implementation of the sensor system cost-effective and free of the influence of environmental and system fluctuations.     

Theory and practice of long-period gratings: when a loss becomes a gain

Losses of cladding modes are part of the mechanism of operation of a long-period grating (LPG) when it is used as an optical filter. We present a LPG computer simulation that accounts for these losses. On the basis of this simulation, we show that losses result in qualitatively different LPG spectral behavior. There is an optimal loss value that provides sidelobe-free, 100% power transfer from the core to the cladding mode for a uniform LPG. We obtained a simple equation that relates this optimum lose value to the LPG length and the cross-coupling coefficient. Based on the results, we propose new approaches to LPG design in a fiber as well as in waveguide platforms for fiber-optic communication and sensor applications. A design of a LPG reconfigurable filter is suggested.     

Temperature-independent bending sensor with tilted fiber Bragg grating interacting with multimode fiber

A new type fiber bending sensor based on a tilted fiber Bragg grating (TFBG) interacting with a multimode fiber (MMF) is presented. The sensing head is formed by insertion of a small section of MMF between a single-mode fiber (SMF) and the TFBG. The average reflective power in the cladding modes decreases with the increase of curvature. The measurement range of the curvature from 0 to 2.5 m⁻¹ with a measurement sensitivity of −802.4 nW/m⁻¹ is achieved. The proposed sensor is also proved as temperature-independent from the experimental investigation.     

Study and investigation of long period grating as refractive index sensor

In this paper, we have investigated the response of long period grating (LPG) as refractive index sensor. The response has been studied for refractive index variation ranging from 1 to 1.45. In this work, we found that the sensing mechanism is based on two different aspects. First is the change of coupling power from the guided core mode to other co-propagating cladding modes and second is the wavelength shift of the peak resonant wavelengths from their original positions due the change of refractive index of the environmental (external) medium surrounding the cladding of the grating.     

All-fiber Mach-Zehnder curvature sensor based on multimode interference combined with a long-period grating

A novel Mach-Zehnder interferometer based on a fiber multimode interference structure combined with a long-period fiber grating (LPG) is proposed. The multimode interference is achieved through the use of a MMF section spliced between two single-mode fibers, with a length adjusted to couple a fraction of light into the cladding modes. A LPG placed after the MMF couples light back into the fiber core, completing the Mach-Zehnder interferometer. This novel configuration was demonstrated as a bending sensor.     

长周期光纤光栅模式与耦合的研究

长周期光纤光栅是在光纤纤芯中沿轴向形成折射率周期性调制的带阻型光纤器件。与光纤布拉格光栅不同，它表现为前向传播的纤芯基模与同向传播的各阶次包层模式在特定波长的耦合。研究了纤芯基模、包层模式（HE1t/EH1t）及其有效折射率随波长的变化，研究了纤芯基模与包层模式（HE1t/EH1t）的耦合系数。研究表明，纤芯基模与一阶低次包层模式的有效折射率随波长增大而减小，纤芯基模与HE1t产生的耦合系数远大于与EH1t的耦合系数，并且包层模式次数较低时，耦合系数随次数的升高而增加。这与以前的研究结果有所不同。     

Simultaneous strain and temperature measurement based on a photonic crystal fiber modal-interference interacting with a long period fiber grating

An alternative all-fiber sensor for simultaneous strain and temperature measurement based on a photonic crystal fiber (PCF) spliced between single-mode fibers cascaded with a long period grating (LPG) is proposed. By collapsing the air holes at two splicing regions along the PCF, a simple but effective modal-interference (MI) is occurred between the core and cladding modes of the PCF. Due to the different responses on the changes of strain and temperature on the MI and the cascaded LPG, the strain and temperature can be measured simultaneously. Experimental results show that the sensing resolution of 9.1 με in strain measurement is experimentally achieved over a range of 2640 με, while the temperature sensing resolution is 0.27 °C within a range of 30-100 °C.     

Fiber-optic vector vibroscope

A directional vibration sensor based on polarization-controlled cladding-to-core recoupling is demonstrated. A compact structure in which a short section of multi-mode fiber (MMF) stub containing a weakly tilted fiber Bragg grating (TFBG) is spliced to another single-mode fiber without any lateral offset. Multiple core modes of the MMF are coupled at the junction and appear as well defined resonances in reflection from the TFBG. Some of those resonances exhibit a strong polarization and bending dependence. Both the orientation and the amplitude of the vibrations can be determined unambiguously via dual-path power detection of the orthogonal-polarimetric lowest order LP(1n) modes. Meanwhile, the unwanted power fluctuations and temperature perturbations can be referenced out by monitoring the fundamental LP(01) mode resonance.     

Wavelength-selective all-fiber filter based on a single long-period fiber grating and a misaligned splicing point

A novel wavelength-selective all-fiber filter using a single long-period fiber grating (LPG) interacting with a misaligned fusion splicing point has been demonstrated. The misaligned splicing point couples a part of the core mode power into the cladding modes, which is then recoupled into the core mode by the following LPG. As an optical path difference is introduced by the differential refractive index of the fiber, an in-fiber Mach-Zehnder interferometer is therefore formed, which may function as a cost-efficient WDM filter with good isolation and low insertion loss.     

Cascaded tilted fiber Bragg grating for enhanced refractive index sensing

We proposed and experimentally demonstrated a cascaded tilted fiber Bragg grating(TFBG) for enhanced refractive index sensing. The TFBG is UV-inscribed in series in ordinary single-mode fiber(SMF) and reduced-diameter SMF with the same tilt angle, and then excites two sets of superposed spectral combs of cladding modes. The cascaded TFBG with total length of 18 mm has a much wider wavelength range over 100 nm and narrower wavelength separation than that of a TFBG only in the SMF, enabling an enlarged range and a higher accuracy of refractive index measurement. The fabricated TFBG with the merits of enhanced sensing capability and temperature self-calibration presents great potentials in the biochemical sensing applications.     

模式耦合理论在圆周对称长周期光纤光栅建模中的应用

长周期光纤光栅是不同于光纤Bragg光栅的一种光纤光栅器件 ,根据模式耦合理论 ,长周期光纤光栅表现为前向传播的纤芯导模和同向的各阶次包层模式之间的耦合。分析研究了长周期光纤光栅轴向的模场变化。忽略轴向的模式耦合以及包层模式之间的相互耦合作用 ,并认为折射率指数的调制只存在于纤芯中 ,建立了简化的长周期光纤光栅数学模型。对圆周对称轴向均匀型长周期光纤光栅谱特性进行了仿真 ,其结果与实验结果基本吻合 ,表明了简化的数学模型的合理性     

基于模式转换及双峰谐振效应的薄包层镀膜长周期光纤光栅特性研究

基于耦合模理论,首先研究了镀膜长周期光纤光栅(LPFG)高阶包层模的模式转换,划分了高阶包层模的非模式转换区及模式转换区。分析了高阶包层模有效折射率随薄膜厚度增加的响应特性,包层模谐振波长在模式转换区的偏移量要大于非模式转换区。在此基础上,研究了不同包层半径下高阶包层模谐振波长随光栅周期的变化情况,结果表明,相同包层半径下模式转换区内双峰间距的偏移量大于非模式转换区;无论在模式转换区还是非模式转换区,包层半径的减小将增加双峰间距的偏移量。最后分析了不同包层半径下的高阶包层模双峰透射谱在模式转换区及非模式转换区内的折射率响应,进而提出了薄包层镀膜LPFG的优化设计方案,当选定敏感膜层厚度及折射率处于镀膜LPFG的模式转换区内,光栅周期靠近相位匹配转折点时,将得到灵敏度高于传统LPFG双峰传感器的镀膜LPFG折射率型双峰传感器;而减小包层半径,将进一步提高传感器的分辨本领。     

振幅掩膜紫外写入的长周期光纤光栅特性研究

振幅掩膜紫外写入的长周期光纤光栅的纤芯折射率分布函数为矩形波。以三层阶跃折射率光波导结构基础，用弱导标量近似和标量耦合模理论分析折射率调制类型为矩形波的长周期光纤光栅的特性。详细地给出耦合模方程近似处理的方法，并说明了其合理性。用数学软件Matlab进行了数值模拟计算，发现折射率调制类为矩形波的光栅传输谱不是由它的各次余弦光栅谱的线性叠加而成的。还研究了外部环境折射率、包层半径、栅占空比等光栅结构参量对矩形折射率调制的光栅传输谱的影响。同时指出了每阶包层模的双谐振峰位置随栅参量的变化规律。刊■刊『_型，刿j1     

长周期光纤光栅和双锥形光纤间的倏逝波耦合作用

对长周期光纤光栅和双锥形光纤之间的倏逝波耦合作用进行了研究。理论分析和实验研究表明,由于锥形光纤和长周期光纤光栅物理边界外倏逝波之间的交叠,长周期光纤光栅产生的包层模,可以耦合到锥形光纤的包层模并从锥形光纤的纤芯输出。要获得高的耦合效率,应满足模式匹配的条件,同时要尽量减小两光纤之间的距离。耦合特性还与长周期光栅和双锥形光纤的相对位置有关,为获得高的耦合效率,耦合区应位于长周期光栅区的后面。这种倏逝波耦合作用,为监测实际应用系统中长周期光纤光栅的特性提供了一种新方法;为利用锥形光纤和长周期光纤光栅开发新型光纤器件,提供了一种可能的方案。     

Refractive index sensor based on stress-induced long period grating

We proposed a novel refractive index sensor based on a side-polishing fiber to be cascaded with a stress-induced long period fiber grating (LPG), which is created by applying a force to a V-grooved plate on the single mode fiber with micro-bending deformation. When the refractive index (RI) surrounding the side-polishing surface is changed, the LPG-induced cladding mode light could be coupled back to the core mode, so that it will result in the magnitude variation of LPG loss-peak. This property of index sensing based on the stress-induced LPG by monitoring the power-level change may be exploited in chemical sensing and environmental monitoring applications.     

Cladding index modulated fiber grating

A new type of fiber grating with only cladding index modulation is presented. Characteristics of both cladding index modulated short-period fiber grating (FBG) and long-period fiber grating (LPFG) are analyzed. The calculation of the modes involved in this paper is based on a model of three-layer step-index fiber geometry. Transmission of a mode guided by the core through a cladding index modulated grating when evanescent field coupling occurs is analyzed with couple-mode theory. Evanescent field coupling causes a power flowing from the core to the cladding, so the attenuation of the new grating is analyzed as well. Lower attenuation, flexible spectral characteristics are demonstrated in comparison with traditional fiber core index modulated grating.     

Method for measuring liquid phase diffusion based on tilted fiber Bragg grating

We propose and experimentally demonstrate a method for measuring liquid phase diffusion based on tilted fiber Bragg grating (TFBG). By monitoring the transmission spectra of the TFBG placed at different positions of the diffusion zone and calculating the normalized area enclosed by the upper and lower envelope curves of the cladding modes, the distribution curves of the glycerol concentration are obtained, according to the experimental calibration formulas between the glycerol concentration and the normalized area. This method can conveniently achieve remote and distributed measurement of the liquid phase diffusion in hostile environment because of its all-fiber structure.