Investigations on burst length in optical burst switched networks

In this paper, we investigate the performance of optical burst switched networks for erbium-doped fiber amplifiers (EDFAs) and semiconductor optical amplifiers (SOAs). We show that EDFAs are more suitable for burst switching as compared to SOAs. We further investigate the burst length for 18, 24.6 and 55 km optical switched network. It is observed that burst length should neither be very small nor very large. If the burst length is small, throughput will be less, and if the burst length is very large, delay will be very large. This is due to higher wait times incurred when packets are formed into larger bursts causing additional overall delay. It is observed that performance decreases up to a small burst length of 1500 μs, which is the minimum burst length required for the creation of the burst. Once this burst is created, there is significant improvement in the quality factor up to 3000 μs. After this burst length, the performance again degrades. Hence the burst length can be optimized for the best quality factor in optical burst switched networks. We further show that by increasing EDFA gain, the quality deteriorates as increasing the EDFA gain results in increased levels of additive phase noise, which can further induce nonlinearities.     

Comparison analysis of optical burst switched network architectures

Optical burst switching (OBS) is a promising paradigm for the next-generation Internet infrastructure. In this paper, a novel efficient network architecture for OBS has been presented and compared with conventional OBS architectures. To enhance OBS system performance, the architecture employs a novel proposed burst assembly algorithm, fiber delay lines (FDLs) and dynamic route selection technique. A queuing model is used to predict the system behavior for both classless and prioritized traffic. Simple closed-form expressions are obtained for the burst-loss probability of both classless and prioritized traffic. Numerical results show that the proposed architecture provides an accurate fit for the performance of the highest traffic class and lower bounds for the other traffic classes that are tighter than earlier known results.     

Distributed queue optical burst switched ring—A MAC protocol with zero blocking for OBS ring networks

Optical burst switching is a switching technology that is able to provide viable switching for optical internet with the present day technology. This paper presents a new medium access protocol for wavelength division multiplexing based optical burst switched metro ring network namely distributed queue optical burst switched ring (DQOBSR). It is a slotted, distributed queue access protocol with fixed bus structure and simple wavelength assignment. The topology consists of two unidirectional, counter rotating rings and the medium access protocol is based on distributed queuing. The protocol provides zero blocking with acceptable access delays. A mathematical model is also presented to determine the mean access delay which is the important performance parameter for the protocol. The simulation and model based results are compared and found to be in good agreement.     

OBS网络中基于优先级与突发包分割的偏射路由机制

为了有效地降低突发包的丢失率和保证OBS网络中不同优先级业务的服务质量,提出了一种基于优先级与突发包分割的偏射路由机制.当冲突发生时,首先基于突发包的优先级进行"竞争突发包头部分割或者原突发包尾部分割"处理;无冲突部分直接在事先预留的输出数据信道上处理,冲突部分的分割突发包根据参数可调的偏射路由机制被偏射到最佳偏射路径上.仿真结果表明,该机制能够有效地降低整个网络的丢包率和端到端的延时,并且得到高优先级突发包的丢失率和延时低于低优先级突发包.由此可知,基于优先级与突发包分割的偏射路由机制能够有效地解决突发包的冲突问题,从而提高整个OBS网络的性能.     

An optimal protection and restoration scheme (OPARS) for optical networks

Protection and restoration are critical network design issues for optical networks since even a single failure for a short duration may result in huge data loss due to the large capacity of optical fibers. However, few studies have been done on these issues for optical burst switching (OBS) networks. Protection and restoration are essential mechanisms for guaranteeing more reliable traffic delivery services. But it is not easy to apply existing mechanisms to optical burst switching (OBS) networks due to its one-way reservation signaling and the statistical burst multiplexing. Thus, to achieve the high transmission performance and reliability simultaneously, unique properties of OBS must be considered in the design of protection scheme. In this paper, an optimal protection and restoration scheme (OPARS) has been introduced that not only optimizes the number of provisioned protection wavelengths adaptively based on the traffic load as well as the quality of service (QoS) requirements of bursts in high speed networks but also minimizes burst loss rates. In addition, the proposed scheme has been used as an efficient contention resolution technique. The simulation results verify that the proposed scheme improve the network resource and channel utilization while guaranteeing the targeted protection reliability and QoS requirements of bursts.     

An adaptive reservation scheme for optical network

In this paper, the various Optical Burst Switching (OBS) reservation schemes have been examined in order to reduce data loss caused by either channel scheduling or resources. A novel multi-service OBS edge node with synchronized bandwidth reservation mechanism (SRM) has been proposed, which enables high-speed network transport nodes to dynamically reserve bandwidth needed for active data burst flows. The performance of the proposed mechanism is evaluated by means of NS-2 simulation. The results show that the packet delay is kept within the constraint for each traffic flow and the performance metrics such as burst loss rate, throughput and fairness are remarkably improved.     

Analysis of burst/packet assembly techniques in high-speed optical switching network

In the Optical Burst Switching (OBS) Network, the burst assembly technique is one of the challenging issues in the implementation of the system. It has the influence on the burst characteristic, which gives an impact on the network performance. Burst assembly is the process of assembling incoming data from the higher layer into bursts at the ingress edge node of the OBS network. The burst assembly mechanism must then place these packets into bursts based on some assembly policy. In this paper, the OBS system performance has been observed in simulated 12-node network based on Just-Enough-Time (JET) reservation protocol with various burst assembly techniques under the standard drop policy (DP) and the segmentation policy for contention resolution. The simulation results show that the performance of the proposed Adaptive-Threshold with Fixed Maximum Time Limitation (ATH-FMTL) burst assembly scheme is better than conventional burst assembly schemes in terms of loss probability and average assembly delay. Also, the proposed scheme avoids a sudden increase in the burst size and makes the burst sent out smoother as compared to conventional schemes.     

A maximum-efficiency-first multi-path route selection strategy for optical burst switching networks

In this paper, the impact of a path selection on other existing paths in optical burst switching (OBS) networks is studied by analyzing the contention among different traffic streams and the interaction between the route selection and traffic load balance. The results show that there exists a mutual reinforcement interaction among the traffic load of a path, the path burst loss ratio and the contention ability of the path when burst loss ratio based multi-path selection strategies are adopted, which may increase the unbalance of traffic and lead to severe congestion further. A maximum-efficiency-first multi-path selection strategy, which considers the performance of the burst flows and the impact of a path selection on existing OBS paths at the same time by a combined metric of route efficiency, is proposed to maximize the utility of the burst flows and minimize the increment of lost throughput on the path. The performance of the proposed multi-path selection strategy is evaluated through simulation. The results show that the presented strategy obviously outperforms the least burst loss ratio strategy and shortest path first strategy in terms of the burst loss ratio in the practical unbalanced background traffic, especially when the network is heavily loaded.     

An optimal burst assembly approach employing traffic shaping (OBATS) for OBS

Optical burst switching (OBS) aims at combining the strengths of packet and circuit switching and is considered as a promising technology for implementing the next generation optical Internet, required to cope with the rapid growth of Internet traffic and the increased deployment of new services. In this paper, an optimal burst assembly approach employing traffic shaping (OBATS) for OBS networks has been proposed in order to improve network performance in terms of reduced blocking probability, congestion control and better utilization of bandwidth. Particularly, the proposed scheme aims at reducing the average delay experienced by the packets during the burstification process in optical burst switched (OBS) networks, for a given average size of the bursts produced. Reducing the packet burstification delay, for a given average burst size, is essential for real-time applications; correspondingly, increasing the average burst size for a given packet burstification delay is important for reducing the number of bursts injected into the network and the associated overhead imposed on the core nodes. Simulation results show that the proposed burst assembly approach gives better network performance in terms of burst drop, resource contention and delay as compared to conventional burst assembly approaches.     

光突发交换中交换矩阵配置时间的影响研究

光突发交换是近几年出现的一种很有前途的交换技术。在光突发交换网络的核心节点中,光交换矩阵是一个关键部件,其配置时间影响到光突发交换网络的性能。这种影响表现在对数据信道可用时间施加了限制。在考虑光交换矩阵配置时间的基础上给出了修正后的LAUC算法,并通过计算机仿真研究了这种配置时间对光突发交换性能的影响。结果表明,光交换矩阵配置时间的增大会导致输出数据信道利用率的降低,进而增大了数据丢失率。     

Feed-forward control of SOA gain for power equalization in optical burst switching networks

We evaluate the performance of a novel technique to equalize power variation between optical bursts using feed-forward control of semiconductor optical amplifier gain. The technique enables large dynamic range power equalization of incoming optical bursts with up to 10 dB power difference. Moreover, the technique can remove SOA-induced waveform distortion. We achieve more than 4 dB sensitivity improvement with equalized burst power.     

The cost benefits of multi-layer architecture with multi-granularity switching in optical networks

The benefits of using multi-granularity switching to reduce the number of ports, including both electronic and optical ports, have been investigated. A novel multi-layer ring architecture with multiple switches is proposed and two general equations to count the number of ports are derived. Comparisons are made between the multi-layer multi-granularity switching (MM-XC) architecture and the reported architectures: multi-switching (M-XC) and single switching (S-XC) architectures. The results show that the M-XC or S-XC architectures can be deduced from the MM-XC architecture and the latter architecture can achieve more considerable savings of the port count compared to the former.     

An efficient scheme for optimizing channel utilization in OBS networks

Optical burst switching (OBS) is an emerging technology that allows variable size data bursts to be transported directly over DWDM links. In order to make OBS a viable solution, the wavelength scheduling algorithms need to be able to utilize the available wavelengths efficiently, while being able to operate fast enough to keep up with the burst incoming rate. Unfortunately, horizon scheduling cannot utilize the voids created by previously scheduled bursts, resulting in low bandwidth utilization. To date, Min-SV is the fastest scheduling algorithm that can schedule wavelengths efficiently. However, its complexity is O (log m) and it requires 10 log (m) memory accesses to schedule a single burst. This means that it can take upto several microseconds for each burst request, which is still too slow to make it a practical solution for OBS deployment. In this paper, an efficient scheme has been proposed for optimizing channel utilization in OBS networks. In the proposed approach, a burst is represented by an interval of time. The process of scheduling a number of bursts, thus, turns to be a process of fitting a set of the corresponding time intervals on a channel time line that represents a channel-time resource. By doing so, the scheduling process can be formulated as a combinatorial optimization problem. Then, graph theory is applied to schedule as many non-overlapping intervals as possible onto the channel time line. The underlying concept of the proposed scheduling scheme is that of briefly delaying the scheduling of a burst so that a much better decision can be made about a number of bursts all-together. This scheme is shown, through simulations, to improve performance in terms of burst loss probability, channel utilization, fairness-control and data throughput over existing schemes. Thus the proposed scheme is well suited for high performance networks in terms of reliability.     

Performance analysis of an integrated scheme in optical burst switching high-speed networks

A new integrated scheme based on resource-reservation and adaptive network flow routing to alleviate contention in optical burst switching networks is proposed. The objective of the proposed scheme is to reduce the overall burst loss in the network and at the same time to avoid the packet out-of-sequence arrival problem. Simulations are carried out to assess the feasibility of the proposed scheme. Its performance is compared with that of contention resolution schemes based on conventional routing. Through extensive simulations, it is shown that the proposed scheme not only provides significantly better burst loss performance than the basic equal proportion and hop-length based traffic routing algorithms, but also is void of any packet re-orderings.     

A novel collision free WDM optical switching network

To avoid burst collision in OBS-WDM ring network, a novel scheme called Estimated Traffic based Longest Queue First (ETLQF) has been proposed. In it, the scheduler considers both the queue length and the incoming traffic. The scheduler can adjust the queue lengths in advance to cater to the incoming traffic, targeting to reduce cell loss ratio (CLR) and improve the buffer utilization. The simulation results show that the ETLQF in OBS ring networks not only reduces CLR by 10-60%, but also achieves high throughput while saving 65% of wavelengths, when compared to conventional schemes with only destination delay.     

Capacity enhancement in packet switched slotted ring wavelength division multiplexed transport networks

In this paper, all-optical WDM networks based on a slotted multichannel ring topology have been investigated. The nodes are equipped with one fixed-wavelength receiver, wavelength-tunable transmitter and provide packet-mode transport in WDM network. The topology provides one logical channel to be associated with each destination node. Each channel is shared in statistical time division by all nodes transmitting to a given destination. The capacity enhancement has been demonstrated by comparing all optical WDM network by increasing the number of nodes. It is concluded that by increasing the number of nodes in the topology, the token queue length capacity, the token arrival rate are increased and the token arrival period is decreased which results in overall increase in the performance and capacity of the logical WDM network.     

Blocking and delay performance for differential output-ports choosing probability scheme applied optical burst switching network

Differential output-ports choosing probability (DOCP) scheme is a novel traffic outputting model for core router in optical burst switching (OBS) network. In this paper, we provide an analytical model for studying the performance of traffic blocking and delay in DOCP-applied OBS network. We first evaluate blocking probabilities using DOCP and confirm it by simulation. Then, in optical buffer-equipped OBS core router, we consider the average delay time for buffered traffic and the average total traffic queueing length in core router. The knowledge of delay performance is useful for the optical buffer architecture configuration in differential traffic scenario. Several results indicate that, under the same load condition, the blocking probabilities and the delay time will change along with the changeable ports choosing probability and the ratio between different length bursts in the OBS system.     

一种新的光突发交换网络信令协议与分析

提出了一种新的光突发交换网络信令协议,即DSH区分服务混合信令.根据实时（电路仿真）业务和非实时（数据）业务对QoS的不同要求分别采用TAW和JET信令控制协议,尤其是对TAW信令做了相应改进,使之更适合于OBS网络承载电路仿真业务.利用电路仿真业务发出的呼叫请求,在端到端的波长通道中建立虚通路,并在整个呼叫持续过程中保持虚通路的连接,这样可以保证电路仿真业务的端到端时延最小并避免信息丢失.通过理论分析和系统仿真,研究了DSH混合信令的性能及其对波长利用率和实时业务呼损率的影响.     

TCP在光突发交换试验网络中性能的实验研究

在光突发交换试验网络中对TCP的性能进行了实验研究.首先研究了丢包对网络性能的影响,表明突发包丢失将导致TCP吞吐量的快速下降,并且丢包率越高,可用的TCP传输带宽越窄.然后分别详细研究了OBS试验网络中的延时损伤和报文段关联增益,以及对TCP传输性能的影响.最后综合考虑这些因素.实验结果表明,在本OBS试验网络中存在一个不随丢包率变化的最优化突发包组装时间250us使得可用TCP带宽最大化.为了最大限度地提高TCP的传输性能,组包时间应该选择等于或稍大于这个最优值.     

一种新型的突发汇聚算法研究

分析了现有的突发汇聚算法,同时针对现有汇聚算法的一些特点,提出了一种新型突发包汇聚算法,可以实现在不同网络负载的情况下,根据到达边缘节点的速率同时结合网络的性能(丢包率),动态的调整突发包汇聚的门限值,从而实现了智能组包,克服了原有算法简单,不灵活的缺点.通过仿真结果可以得知,该算法可以明显改善光突发交换网络的丢包率和时延性能,能够很好地支持实时性要求很高的数据业务.