Continuous Atmospheric Plasma Oxidation of Carbon Fibres: Influence on the Fibre Surface and Bulk Properties and Adhesion to Polyamide 12

Continuous atmospheric plasma oxidation (APO) was used to introduce oxygen functionalities to the surface of carbon fibres in an attempt to enhance interfacial adhesion between carbon fibres and polyamide-12 (PA-12). APO only affects the surface properties of the fibres while their bulk properties remained unchanged. Contact angle and ζ-potential measurements demonstrated that APO-treated fibres became significantly more hydrophilic due to the introduction of polar oxygen-containing groups on the fibre surface, which also resulted in an increase of surface energy on the carbon fibres. The interfacial shear strength of single carbon fibre/PA-12 model composites, determined by single fibre fragmentation tests, showed an increase from 40 to 83 MPa with up to 4 min of APO treatment time which confirms that the fibre/matrix interfacial adhesion was enhanced. This highlights that the incorporation of APO into composite manufacturing will allow tailoring of the fibre/matrix interface.     

Interfacial strength and mechanisms of silicone resin composites reinforced with 2 different polyhedral oligomeric silsesquioxanes/carbon fiber hybrids

Grafting nanoscale reinforcement onto macrolevel carbon fiber (CF) surface is an efficient approach to improve interfacial strength and properties of composites. In the research, 2 different polyhedral oligomeric silsesquioxanes (POSS)/CF hybrids have been prepared by a facile 2‐step method. Carbon fiber was grafted with aniline groups by aryl diazonium reaction using water as the reaction medium, and then separately functionalized with glycidyllsobutyl POSS (EP0418) or glycidyl POSS (EP0409) by the chemical bonding. Characterization of fiber surface structures before and after modification confirmed the covalent bonding nature between both kinds of POSS and CF. Atomic force microscopy images showed the uniform distributions of EP0418 or EP0409 modified on the fiber surface and the similar enhanced degree of surface roughness (89.3 and 88.7 nm). Dynamic contact angle tests showed that EP0409‐grafted CF (CF‐g‐EP0409) had lower contact angles and higher surface free energy than those of EP0418‐grafted CF (CF‐g‐EP0418). Interfacial strength and hydrothermal aging resistance of composites enhanced significantly after POSS modification, especially for CF‐g‐EP0409 composites. Interfacial reinforcing mechanisms of composites reinforced with 2 different POSS/CF hybrids have also been analyzed and compared.     

连续纤维增强含二氮杂萘酮联苯结构聚芳醚砜酮树脂基复合材料的界面

利用射频感性耦合冷等离子体(ICP)处理技术改性连续纤维表面,分别采用X射线光电子能谱(XPS)、原子力显微镜(AFM)及动态接触角分析(DCA)系统研究了等离子体处理时间、放电气压、放电功率等工艺参数对连续碳纤维、芳纶纤维和对亚苯基苯并二噁唑(PBO)纤维的表面化学成分、表面形貌、表面粗糙度及表面自由能的影响.研究结...     

Mechanical properties of plasma‐treated carbon fiber reinforced PTFE composites with CNT

This paper is concerned with the effects of the plasma surface treatment and the addition of CNT on the mechanical properties of carbon fiber/polytetrafluoroethylene (PTFE) composite. The tensile and flexural strength of composites containing CNT and plasma‐treated carbon fibers improved. The flexural strength first decreases with respect to the CF content. The flexural strength increases to 179 MPa for the plasma‐treated composite as compared with 167 MPa for the neat carbon fiber composites. The overall improvement is thus nearly 8%.     

Mechanical properties, crystallization and melting behaviors of carbon fiber-reinforced PA6 composites

Polyamide-6 (PA6)/carbon fiber (CF) composites were prepared by melt-extrusion via continuous fiber fed during extruding. The mechanical, thermal properties, and crystallization behavior of PA6/CF composites were investigated. It was found that the tensile modulus and strength of the composites were increased with the addition of CF, while their elongations at break were decreased. Scanning electron microscopy observation on the fracture surfaces showed the fine dispersion of CF and strong interfacial adhesion between fibers and matrix. Dynamic mechanical analysis results showed that the storage modulus of PA6/CF composites was improved with the addition of CF. Non-isothermal crystallization analysis showed that the CF plays a role as nucleating agent in PA6 matrix, and the α-form crystalline structure was favorable in the PA6/CF composites, as confirmed from the X-ray diffraction analysis. A trans-crystallization layer around CF could be observed by polarizing optical microscopy, which proved the nucleation effect of carbon fiber surface on the crystallization of PA6. The thermal stability of PA6/CF composites was also enhanced.     

Wettability of carbon fibers modified by acrylic acid and interface properties of carbon fiber/epoxy

The oxidation-reduction and pre-irradiation induced methods were employed to study the effect of acrylic acid modification on the wetting and adsorption ability of carbon fiber (CF) in epoxy solution and the interfacial properties of CF/epoxy. Systematic experimental work was conducted to determine the surface topography, surface energy, surface chemical composition, absorbability and tensile strength of carbon fibers and interfacial adhesion of CF/epoxy before and after modification. The roughness, surface energy, amount of containing-oxygen functional groups and wetting ability were all found to increase significantly after modifications. The tensile strength of carbon fibers was improved marginally by γ-ray pre-irradiation while was decreased little by oxidation-reduction modification. Consequently, the surface modifications of carbon fibers via both oxidation-reduction and pre-irradiation led to an improvement (more than 15%) of the interlaminar shear strength of CF/epoxy composites. The mechanisms of interfacial improvement of modified CF/epoxy composites are proposed.     

Influence of surface properties of graphene oxide/carbon fiber hybrid fiber by oxidative treatments combined with electrophoretic deposition

An effective way to prepare graphene oxide/carbon fiber hybrid fiber was proposed by the treatment with hydrogen peroxide and concentrated nitric acid combined with electrophoretic deposition process. Surface functional group, surface roughness, and surface morphologies of carbon fibers were examined by Fourier transform infrared spectrometer, atomic force microscopy, and scanning electron microscopy. Results showed that a uniform and thick graphene oxide films were constructed on the surface of carbon fiber. Deposition density increased by introduction of pretreatment of the carbon fiber in the electrophoretic deposition process has been shown as a possible method. Dynamic contact angle analysis results indicated that the deposition of graphene oxide significantly improved surface free energy of carbon fiber by increasing surface area and polar groups. The introduction of graphene oxide in the carbon fiber‐reinforced epoxy composites results in a 55.6% enhancement in the interfacial shear strength and confirms the remarkable improvement in the interfacial adhesion strength of the composites, and the fracture mechanism was also analyzed. Copyright © 2016 John Wiley & Sons, Ltd.     

Modification effects of short carbon fibers on mechanical properties and fretting wear behavior of UHMWPE composites

The present work comparatively studied the modification effects of short carbon fiber (CF) on the mechanical properties and fretting wear behavior of ultra‐high molecular weight polyethylene (UHMWPE)/CF composites. The interactions between CFs and UHMWPE interface were also investigated in detail. The results showed that, with the increase in fiber content, the compressive modulus and hardness of the composites increased, while its impact strength decreased. It was found that filling of CF can reduce the friction and wear of UHMWPE. In addition, the UHMWPE‐based composites reinforced with nitric acid‐treated CF exhibited better mechanical properties, lower friction coefficient, and higher wear resistance than those of untreated UHMWPE/CF composites. This was attributed to the improvement of interfacial adhesion and compatibility between CF and UHMWPE matrix caused by surface chemical modification of CF. Copyright © 2015 John Wiley & Sons, Ltd.     

Plasma treatment of carbon fiber on the tribological property of polyimide composite

The effect of different ratios of carbon fiber (CF) reinforcing polyimide (PI) and surface treatment of CF on the microstructure and wear resistance of surface layers was studied. The increase of CF content led to a gradual increase in the Interlaminar shear strength (ILSS) values, and the maximum ILSS value arises when the CF content is 15 vol%, with an improvement of 13.45% compared to virgin CF composites. The increased interfacial adhesion could be contributed mainly to the presence of branched PI at the interface region. SEM of the worn surface confirms that the plasma treatment efficiently improves the interfacial adhesion of CF/PI composite. Copyright © 2017 John Wiley & Sons, Ltd.     

Improvement of interfacial adhesion in PP/PS blends enhanced with supersonic atmosphere plasma spraying surface‐treated carbon fiber

The effects of surface treatment of a carbon fiber (CF) by supersonic atmosphere plasma spraying (SAPS) on the interfacial adhesion behavior and morphology of polypropylene/polystyrene (PP/PS) matrix blends filled CF composites were investigated. Effects of surface treated a commercial CF on mechanical properties are studied. Contact angle was measured to examine the changes in wettability of the CF. The chemical and morphological changes were characterized by using X‐ray photoelectron spectroscopy and scanning electron microscopy. PP/PS/CF composites were fabricated with and without SAPS treatment, and their interlaminar fracture toughnesses were compared. The results showed that the interlaminar shear strength of composites has been greatly improved filled SAPS modification CF. The water contact angle of resin sample decreased 50% after addition of SAPS surface‐treated CF. Scanning electron microscopy results on the fractured surface exhibited PP/PS blends adhered well around the CFs of the SAPS‐treated specimen compared with that of the untreated specimen. This attributed to the CF interlock, and it improves the wetting between fibers and resins. Copyright © 2017 John Wiley & Sons, Ltd.     

The effect of surface coating of CNTs on the mechanical properties of CF‐filled HDPE composites

Mechanical properties of carbon fiber (CF) and carbon nanotube (CNT)‐filled thermoplastic high‐density polyethylene (HDPE) composites were studied with particular interest on the effects of filler content and fiber surface treatment by coupling agent. Surface‐treated CF‐filled HDPE composites increased their tensile strength and impact strength, which is further increased with the addition of CNT. SEM showed that CNT‐coating‐treated CF‐HDPE composites show better dispersion of the filler into the matrix, which results in better interfacial adhesion between the filler and the matrix. Copyright © 2014 John Wiley & Sons, Ltd.     

Improving the interfacial property of carbon fiber/PI resin composite by grafting modification of carbon fiber surface

The poor interfacial adhesion between carbon fibers (CFs) and polyimide (PI) resin has seriously hampered the application of CF/PI composites. In this work, the interfacial adhesion was efficiently enhanced by grafting on the CF surface. Surface morphology and surface composition of modified carbon fibers were characterized, which indicated that acrylamide was grafted successfully on the CF surface and the surface roughness was increased slightly. After grafting, the interface shear strength of modified carbon fibers/PI composites was significantly improved by 86.96%, and the interlaminar shear strength was enhanced by 55.61% due to the covalent bonds in interphase and the toughening effect of sizing agent. Moreover, the mechanical properties of composites with different interfacial adhesion were measured, which further confirmed the effect of the grafting modification.     

The effect of surface modification with nitric acid on the mechanical and tribological properties of carbon fiber‐reinforced thermoplastic polyimide composite

Polyacrylamideacrylate (PAN)‐based carbon fibers were submitted to nitric acid oxidation treatments to improve the interfacial adhesion of the carbon fiber (CF)‐reinforced polyimide (CF/PI) composite. The carbon fiber surfaces were characterized by X‐ray photoelectron spectroscopy (XPS). Nitric acid oxidation not only affects the oxygen concentration but also produces an appreciable change in the nature of the chemical functions, namely the conversion of hydroxy‐type oxygen into carboxyl functions. Nitric acid oxidation treatment modifies the element constituting the fiber, the nitrogen concentration being about 1.2 times higher at the fiber external surface compared to the untreated one. The mechanical and tribological properties of the polymide (PI) composites reinforced by the carbon fibers treated with nitric acid oxidation were investigated. Results showed that the tensile strength of the CF/PI composites improved remarkably due to nitric acid treatment along with enhancement in friction and wear performance. Copyright © 2009 John Wiley & Sons, Ltd.     

Interfacial studies on the ozone and air‐oxidation‐modified carbon fiber reinforced PEEK composites

In this work, ozone modification method and air‐oxidationwere used for the surface treatment of polyacrylonitrile(PAN)‐based carbon fiber. The surface characteristics of carbon fibers were characterized by XPS. The interfacial properties of carbon fiber‐reinforced (polyetheretherketone) PEEK (CF/PEEK) composites were investigated by means of the single fiber pull‐out tests. As a result, it was found that IFSS (interfacial shear strength) values of the composites with ozone‐treated carbon fiber are increased by 60% compared to that without treatment. XPS results show that ozone treatment increases the amount of carboxyl groups on carbon fiber surface, thus the interfacial adhesion between carbon fiber and PEEK matrix is effectively promoted. The effect of surface treatment of carbon fibers on the tribological properties of CF/PEEKcomposites was comparativelyinvestigated. Experimental results revealed that surface treatment can effectively improve the interfacial adhesion between carbon fiber and PEEK matrix. Thus the wear resistance was significantly improved. Copyright © 2009 John Wiley & Sons, Ltd.     

Rapeseed oil as main component in synthesis of bio-polyurethane-polyisocyanurate porous materials modified with carbon fibers

Porous polyurethane-polyisocyanurate (PUR-PIR) composites have been synthesized using two types of rapeseed oil-based bio-polyols. The bio-polyols from rapeseed oil were synthesized using two methods: (i) transesterification and (ii) epoxidation followed by oxirane ring opening. The PUR-PIR porous materials were prepared with two isocyanate indices, 150 and 250, and were modified with carbon fibres (CF) in an amount of 3 and 6 wt% of the total foam mass. The structure of the composites was examined using scanning electron microscopy. Thermal and mechanical properties of the composites were determined through a thermogravimetric analysis and measurements of the thermal conductivity, compressive strength, and Young modulus. The influence of CF on the composite flammability was analyzed using oxygen index and cone calorimeter tests. The investigations of the mechanical properties have shown that the compressive strength is the most beneficial in the case of the PUR-PIR foams modified with 6 wt % of CF. The studies have shown that the oxygen index of the composites increases with an increasing CF content and isocyanate index. An addition of CF reduces the heat rate release, especially for the materials with an isocyanate index of 250. An introduction of CF into the PUR-PIR foam structure is a way to improve the thermal stability and to decrease the flammability of final porous composites.     

Enhanced mechanical properties of carbon fiber composites by grafting different structural poly(amido amine) onto fiber surface

The mechanical properties of carbon fiber composites depend on the interfacial strength between fiber and epoxy matrix. Different poly (amido amine) (PAMAM) dendrimers were grafted onto carbon fiber to improve the interfacial strength of the resulting composites. Functional groups on the carbon fiber surface were examined by X-ray photoelectron spectroscopy. The surface morphology of the resulting materials was characterized by scanning electron microscopy and atomic force microscope. The characterization results revealed that PAMAM dendrimers were chemically grafted onto the surface of carbon fiber. More importantly, the mechanical properties of the resulting composites were enhanced owing to the presence of sufficient functional groups on the carbon fiber surface. In addition, after PAMAM containing chair conformations were grafted, the interlaminar shear strength had the highest increase of 53.13%, higher than that of the fiber grafted with PAMAM containing terminated linear amine. This work provides an alternative approach to enhance the mechanical properties of fiber composites by controlling the interface between fiber and epoxy matrix.     

Improved interfacial properties of PI composites through graphene oxide and carbon nanotubes on carbon fiber surface

Carbon nanotubes (CNTs) have been identified as excellent nanoreinforcements for carbon fiber (CF)–reinforced polymers regarding a wide range of engineering applications. The outstanding properties of CNTs, such as their large surface area, high mechanical strength, and low manufacturing cost bring them to be distinguished nanoreinforcements for carbon fiber–reinforced polymers to form multifunctional and multiscale composites. Electrophoretic deposition of graphene oxide for CNTs onto the CF surface was conducted. The presence of graphene oxide–CNTs may effectively increase both the roughness and wettability of the CF surface, resulting in an improvement to the interfacial bonding strength between the CF and the polyimide (PI).     

The interlaminar shear strength and tribological properties of PA 6 composites filled with graphene oxide‐treated carbon fiber

The objective of this work is to improve the interlaminar shear strength and tribological properties of the PA 6 composites by graphene oxide‐treated carbon fiber (CF) and ultraviolet irradiation of PA 6. The morphologies of untreated and treated CFs were characterized by X‐ray photoelectron spectroscopy. Surface analysis showed that after treatment, the surface of CFs chemisorbed oxygen‐containing groups; active carbon atom, the surface roughness, and wetting ability were increased. The results show that the treated CF composites can possess excellent interfacial properties and tribological properties accordingly after treatment. Copyright © 2017 John Wiley & Sons, Ltd.     

Increased interfacial adhesion between carbon fiber and poly(vinylidene fluoride) by an aqueous sizing agent

The adhesion behavior of poly(vinylidene fluoride) (PVDF) to carbon fiber (CF) has always been a huge challenge, on account of the inertness nature of PVDF and the lack of reactive functional groups. In this work, a novel maleic anhydride grafted PVDF (MPVDF) aqueous sizing agent was prepared to modify the interface between CF and PVDF matrix. The surface properties of desized, MPVDF‐sized, and PVDF‐sized carbon fibers were characterized by the scanning electron microscopy, X‐ray photoelectron spectroscopy, atomic force microscopy, and dynamic contact angle analysis test. The results demonstrated that the surface roughness increased from 39 to 55 nm, and surface energy increased from 40 to 74 mN m^?1 after MPVDF sizing treatment. The content of activated carbon atoms increased from 31.0% to 48.4%. Subsequently, the interlaminar shear strength was examined, for which was a critical indicator of the interfacial adhesion between CF and matrix. Compared with the desized CF, the value of interlaminar shear strength increased from 14.8 MPa to 25.5 MPa improved by 72% because of the improved H‐bonding formation, surface roughness, and wettability for MPVDF‐sized CF. In addition, the flexural strength and modulus were also improved by 47% and 74%, respectively. Copyright © 2016 John Wiley & Sons, Ltd.     

The addition of clay on the mechanical properties of surface‐treated CF‐filled PA66 composites

Polyamide 66 (PA66) composites filled with clay and carbon fiber (CF) were prepared by twin‐screw extruder in order to study the influence of nanoparticle reinforcing effect on the mechanical behavior of the PA66 composites (CF/PA66). The mechanical property tests of the composites with and without clay were performed, and the fracture surface morphology was analyzed. The results show that the fracture surface area of the clay‐filled CF/PA66 composite was far smoother than that of the CF/PA66 composite, and there formed a tense interface on the CF surface after the addition of clay. The tensile and flexural strength of CF/PA66 composites with clay was improved. The impact strength decreased because of the high interfacial adhesion. In conclusion, the addition of clay favored the improvement of the higher interface strength and so had good effect on improving the tensile and flexural properties of the composites. Copyright © 2017 John Wiley & Sons, Ltd.