焙烧水滑石对含氯中性化混凝土孔隙液中钢筋腐蚀行为的影响

研究了碳酸根型镁铝水滑石(LDH-MgAl-CO3)焙烧产物(CLDH)在含氯离子的中性化混凝土模拟孔隙液中对钢筋腐蚀行为的影响.极化曲线电位监测以及EIS测试表明,经CLDH处理后的孔隙液中钢筋的极化曲线出现明显的钝化区间,其腐蚀电位较未处理的有一定提高,表面的阻抗也有较大增加.此外,离子浓度分析发现,较未处理时,经CLDH处理后的孔隙液其[Cl-]/[OH-]值降低了4～5个数量级.     

Inhibition of steel corrosion by calcium benzoate adsorption in nitrate solutions: theoretical and experimental approaches

The inhibitive effects of calcium benzoate on steel corrosion were studied in sodium nitrate solutions at room temperature. Corrosion parameters of the steel/nitrate and steel/benzoate + nitrate interfaces were obtained from polarization curves. Adsorption parameters of benzoate on steel in sodium nitrate solutions were determined through changes in the degree of surface coverage by the inhibitor, as a function of concentration, time, and adsorption potential. The most likely adsorption configuration of benzoate on iron was envisaged with the help of semiempirical calculations such as extended Hückel calculations. A two-dimensional flat configuration was involving at least two metal atoms, one interacting with the phenolic group and the other with the carboxylate moiety. The effect of chloride on the corrosion inhibition of benzoate was analyzed by exposing the metal to different chloride solution concentrations, from which corrosion parameters were calculated and compared with those in nitrate solutions.     

混凝土中钢筋的腐蚀行为研究

本文探讨了在不同 pH和Cl- 含量的模拟混凝土孔隙液介质中 ,混凝土中钢筋的腐蚀电化学行为 .电化学技术测试结果表明 ,正常情况下 ,钢筋在混凝土中受到高碱性环境的保护 ,耐蚀性好 .但随着介质 pH的降低、Cl- 含量的上升 ,钢筋腐蚀电流升高 ;动电位阳极极化曲线的测试表明 ,钢筋的维钝电流增大 ,击穿电位负移 ,混凝土中钢筋的耐蚀性下降 .这是钢筋表面钝性受破坏的缘故 .     

The effect of chloride concentration and pH on pitting corrosion of AA7075 aluminum alloy coated with phenyltrimethoxysilane

The effect of chloride ion concentration and pH of solution on the corrosion behavior of aluminum alloy AA7075 coated with phenyltrimethoxysilane (PTMS) immersed in aqueous solutions of NaCl is reported. Potentiodynamic polarization, linear polarization, open circuit potential, and weight loss measurements were performed. The surface of samples was examined using SEM and optical microscopy. Elemental characterization of the coating by secondary ion mass spectrometry indicates an intermediate layer between coating and aluminum alloy surface. The corrosion behavior of the aluminum alloy AA7075 depends on chloride concentration and pH of solution. In acidic or neutral solutions, general and pitting corrosion occur simultaneously. On the contrary, exposure to alkaline solutions results in general corrosion only. Results further reveal that aluminum alloy AA7075 is susceptible to pitting corrosion in all chloride solutions with concentrations between 0.05 M and 2 M NaCl; an increase in the chloride concentration slightly shifted both the pitting and corrosion potentials to more active values. Linear polarization resistance measurements show a substantially improved corrosion resistance value in case of samples coated with PTMS as compared to uncoated samples in both neutral (pH = 7), acidic (pH = 0.85 and 3), and alkaline chloride solutions (pH = 10 and 12.85). The higher corrosion resistance of the aluminum alloy coated with PTMS can be attributed to the hydrophobic coating which acts as a barrier and prevents chloride ion penetration and subsequent reaction with the aluminum alloy.     

Hydrophobization of coarse calico by wet treatment in aluminum chloride solutions

This paper describes the method of wet chemistry used for hydrophobization of coarse calico surface. It was found that hydrophobicity of coarse calico surface is achieved by the formation of aluminum oxide on the surface. An experimental plan was drawn up according to the Taguchi method. The effect of soap solution temperature, aluminum chloride solution concentration, sample treatment time in aluminum chloride solution and heat treatment temperature on water absorption, contact angle, capillary absorption and calico moisture content was studied. The dependencies of hygroscopic properties on the process parameters were obtained. Capillary absorption and water absorption of the test samples increased with increasing concentration of aluminum chloride solution. An increase in the processing time of coarse calico samples in an aluminum chloride solution leads to a decrease in the hydrophobicity of the samples. The characteristics of the dependencies of hygroscopic properties on the temperature of heat treatment and the temperature of the soap solution are similar.

     

Relationships between microstructure and pitting corrosion of ADI in sodium chloride solution

Austempered ductile iron (ADI) has complex microstructure containing a multiphase matrix (called ‘ausferrite’), graphite spheres and oxide inclusions. The corrosion resistance of ADI is related to its microstructure which is determined by heat treatment parameters (like austempering temperature, austempering time, austenitising temperature and austenitising time). In the present paper, the electrochemical behaviour and corrosion resistance of ADI have been investigated by means of the electrochemical microcell technique and classical electrochemical measurements in sodium chloride solution. Particular attention has been paid to the influence of austempering temperature on the microstructure and pitting corrosion. It has been shown that ADI austempered at 430 °C has upper ausferritic microstructure and reveals a better corrosion resistance in sodium chloride solution than ADI austempered at 280 °C. Moreover, the corrosion resistance increases as the volume fracture of ferrite increases and the carbon content of austenite decreases. The good corrosion behaviour of ADI austempered at 430 °C was also related to the good coarsening of the austenite grains and broad ferrite needles (less ferrite/austenite interfaces). It has been demonstrated that silicon is the alloying element hindering the anodic dissolution of the alloy.     

Enthalpies of Dilution of Aqueous Solutions of LiCl, KCl, and CsCl at 300, 325, and 350°C

Dilution enthalpies, measured using isothermal flow calorimetry, are reported for aqueous solutions of LiCl, KCl, and CsCl at 300°C and 11.0 MPa, 325°C and 14.8 MPa, and 350°C and 17.6 MPa. The concentration range of the chloride solutions was 0.5 to 0.02m. Parameters for the Pitzer excess Gibbs ion-interaction equation were determined from the fits of the experimental heat data. Equilibrium constants, enthalpy changes, entropy changes, and heat capacity changes for ion association of the chloride salts were estimated from the heat data. For all systems, the enthalpy and entropy changes were positive and had accelerating increases with temperature. The resulting equilibrium constants show significant, but smaller, increases with temperature.     

Protective Properties of a Sol-Gel Coating on Zinc Coated Steel

Galvanised and galvannealed steels are widely used due to their good corrosion resistance in aqueous solutions. However, when additional protection is required, organic coatings, corrosion inhibitors or conversion coatings are used to improve their corrosion protection. In this work, sol-gel coating was used to improve the corrosion behaviour of these two materials. This paper analyses the final protective properties of a sol-gel coating prepared by basic catalysis and its dependence on the sintering temperature and time of treatment. The influence of the sintering conditions on the galvanised and galvannealed substrates is a decisive factor for the coating quality and for the barrier affect against the aggressive media. While heat treatment time is the controlling factor for the galvannealed steels, the temperature is determining in the case of the galvanised. Corrosion mechanisms for sol-gel galvanised steels did not changed with respect to the uncoated steel. However for galvannealed steel, after coating the mechanism is not purely cathodic.     

Fe基非晶和纳米晶合金晶化及电化学腐蚀行为

应用单辊甩带法制备非晶态Fe78Si13B9和Fe73.5Si13.5B9Nb3Cu1薄带,并以非晶晶化退火法制备出纳米晶Fe73.5Si13.5B9Nb3Cu1薄带.利用X射线衍射(XRD)仪和示差扫描量热计(DSC)对该非晶薄带的非晶特性及其晶化过程进行了研究.并用电化学极化曲线的方法和电化学阻抗技术研究了非晶态Fe78Si13B9和纳米晶Fe73.5Si13.5B9Nb3Cu1合金在1mol/LNaOH溶液里的电化学腐蚀行为,用SEM对极化测试后的试样形貌进行了观察;同时还研究了不同的热处理温度对材料结构及在1mol/LNaOH溶液里耐腐蚀性能的影响.结果表明,该非晶薄带的晶化过程分为两步;纳米晶比非晶合金的耐腐蚀性要好;且随着热处理温度的升高,非晶和纳米晶的耐腐蚀性能都得到提高.     

Use of rare earth metal salt solutions for corrosion protection of aluminum alloys and mild steel

The rare earth metal salt (REMS) compounds which are non-toxic and inexpensive have been used successfully for the corrosion protection of commercial aluminum alloys as well as of mild steel. The resistance to localized corrosion of aluminum alloys such as Al 2024, Al 6061 and Al 7075 has been greatly improved by immersion in hot cerium salt solutions. Cerium oxides/hydroxides were formed at sites where intermetallic compounds containing copper were located and eliminated the formation of local cathodes. REMS solutions were also used for sealing of anodized layer on Al alloys replacing toxic chromates. In addition to increased corrosion resistance excellent paint adhesion was observed. Cerium nitrate and yttrium sulfate solutions produced the most satisfactory results. Cerium salts were also applied successfully as inhibitors and as pretreatment for the corrosion protection of carbon steel in hot NH₃/water solutions used in absorption heat pumps. Factorial design experiments have been used to determine the optimum concentrations of CeCl₃ and H₂O₂ as well as the treatment time used in the cerating process for mild steel. The corrosion protection provided by the cerated layer was further improved by cathodic polarization in cerium chloride. A dual corrosion protection strategy employing cerating and addition of a REMS to the working solution is expected to provide long-lasting corrosion protection of mild steel. Dedicated to the ninetieth anniversary of Ya.M. Kolotyrkin’s birth. This article was submitted by the author in English.     

Anodic dissolution of osmium in acid media

The anodic dissolution of Os in acidic solutions was studied under potentiostatic conditions. The results show high dissolution rates that increase markedly at rising potential. The presence of chloride ions and to a greater extent the increase in acidity of the solutions inhibit the anodic corrosion process. The nature of the dissolution products did depend on the solution pH and the concentration of the complexing anion. Thus, in HClO₄ acid and in chloride solutions at low concentration or acidity, Os goes into solution as OsO₄; in concentrated HCl solution, tetraoxide and chloro-osmyl anions are formed. No OsCl₆^2? complex was detected in solution even at high HCl concentration.     

Copper corrosion in soil: influence of chloride contents, aeration and humidity

The corrosion of copper in a typical Portuguese soil was studied. The original soil was characterised, and modifications were produced by adding chloride, and HClO₄ solutions, or by increasing its relative humidity. The aggressiveness degree of the various soil samples was determined. Copper coupons exposed for 3 months in the original and in the modified soil samples were analysed. The average corrosion rates determined from gravimetric data were in good correlation with the soil aggressiveness. The morphology of the corroded copper surfaces, with and without corrosion products, was analysed by visual observation, optical microscopy and scanning electron microscopy. Energy dispersive spectroscopy was used for the semi-quantitative analysis of the corrosion products and X-ray diffraction spectroscopy to identify the crystalline products. Cuprite has been identified on the copper samples corresponding to the interfaces Cu|S6 and Cu|S8, plus paratacamite on the copper coupon exposed to the soil with higher concentration of chloride (S6). Polarisation curves of copper samples in neutral solutions made by adding different amounts of chloride ions to the soil washing water, under deaereated conditions, were recorded and analysed. The passivity breakdown potential has shown, as expected, a displacement to the cathodic direction as the Cl⁻ ion concentration increases.     

氯离子对模拟混凝土孔隙液中钢筋腐蚀行为的影响

应用动电位扫描法研究钢筋在模拟混凝土孔隙液中的腐蚀电化学行为以及氯离子的影响作用,并根据阳极极化曲线的变化揭示钢筋表面钝化膜的击穿电位及其变化规律,得出当溶液pH值分别为12.50和12.00时,由氯离子侵蚀引起的钢筋局部腐蚀,其钝化膜击穿电位突降的浓度临界值.     

Two-Step Electrodialysis Treatment of Monoethanolamine to Remove Heat Stable Salts

Electrodialysis technology was adapted to removal of heat stable salts from aqueous solutions of alkanolamine absorbents, with monoethanolamine as example. Removal of anions of heat stable salts by electrodialysis from a 30 wt % aqueous solution of monoethanolamine with the degree of carbonation of 0.2 mol of CO₂ per mole of monoethanolamine was studied. The two-step removal of heat stable salts by electrodialysis allows the monoethanolamine loss to be reduced and the concentration of residual CO₂ in the absorbent solution to be decreased. The suggested two-step electrodialysis treatment scheme allows the concentration of heat stable salts to be maintained on the required level from the viewpoint of their corrosion activity, the total volume of the concentrate to be decreased by 50%, and the monoethanolamine loss to be decreased by 30%. The treatment unit with the circulation volume of the monoethanol absorbent of 100 m³ h^–1 was calculated for confirming the efficiency of the two-step electrodialysis treatment scheme. As compared to the one-step electrodialysis treatment scheme, the two-step scheme ensures recovery of 50% of monoethanolamine at the same efficiency of the removal of heat stable salts.     

Effect of the alkyl chain of quaternary ammonium cationic surfactants on corrosion inhibition in hydrochloric acid solution

In this study, the effect of the alkyl chain of quaternary ammonium cationic surfactants on corrosion inhibition in hydrochloric acid (HCl) solution was investigated by using dodecyl trimethyl ammonium chloride (DTAC), tetradecyl trimethyl ammonium chloride (TTAC), cetyl trimethyl ammonium chloride (CTAC), and octadecyl trimethyl ammonium chloride (OTAC) as corrosion inhibitors to uncover their structure–efficiency relationships. The effect of the alkyl chain of quaternary ammonium cationic surfactants on corrosion inhibition in HCl solution was studied under different conditions, such as corrosion inhibitor concentration, temperature, and acidity, and this was done using the weightlessness method. The results obtained show that these inhibitors have high corrosion inhibition effect on A₃ steel, and the corrosion inhibition efficiency is dependent on the length of the alkyl chain. At the same concentration, the longer the alkyl chain, the weaker the corrosion inhibition effect. When the temperature was 50 °C and the concentration of corrosion inhibitor was 70 mg/L, the corrosion inhibition efficiency order of the four cationic surfactants was DTAC > TTAC > CTAC > OTAC. Besides, the experimental results obtained show that the adsorption of the inhibitor on the A₃ steel surface conforms to the Langmuir type isotherm, and then the corresponding adsorption thermodynamic parameters were obtained according to these parameters. It was observed that ΔH, ΔS, and E_a increased with increase in the length of the alkyl chain. The adsorption of the inhibitor on the steel surface is an exothermic, spontaneous, entropy process.     

扫描电化学显微镜原位表征pH值对核电蒸汽发生器合金腐蚀行为的影响

用扫描电化学显微镜(SECM)和电化学阻抗谱(EIS)原位表征了溶液pH值对核电蒸汽发生器800 合金溶液中的腐蚀行为的影响. 实验结果表明：在酸性氯化钠溶液中,SECM探针渐进曲线为正反馈,表明800合金为活化阳极溶解,腐蚀电位下的EIS 图呈现完整的单容抗弧特征;而在中性或者碱性溶液中,SECM探针渐进曲线为负反馈,表明800 合金为自钝化,不同阳极电位下的EIS 图均呈现不完整的容抗弧特征,但随着阳极极化电位的增加,EIS 谱容抗弧半径减小,表明钝化膜的耐蚀性下降;SECM二维扫描图像结果显示探针电流增加,表明电极表面活性增加,即钝化膜的溶解速度增加. 而在中性或者碱性溶液中的SECM二维图像中均可观察到若干活性点,这可能与晶界或者金属夹杂物等有关.     

Thermal diffusivity of eutectic of alkali chloride and ice in the freezing-thawing process by temperature wave analysis

Thermal diffusivity of eutectic formed in aqueous alkali chloride solutions (NaCl, KCl, RbCl and CsCl) was determined by temperature wave analysis (TWA) during the freezing-thawing process of aqueous alkali chloride solution. An obvious change of thermal diffusivity in freezing-thawing processes of eutectic was observed with the super-cooling phenomena for each alkali chloride solute. The rate of thermal diffusivity decrease during the eutectic melting in comparison to the total decrease from the solid to the liquid state was observed larger than that of the heat of fusion measured by DSC, especially in the dilute concentration. It was confirmed that thermal diffusivity was sensitively influenced by the highly structure of the coexistence of eutectic crystallization and ice.     

Electrochemical Behavior and Nonlinear Mott-Schottky Characterization of a Stainless Steel Passive Film

The electrochemical behavior of 304-stainless steel in solutions with different pH values and chloride concentrations was investigated by potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), and a nonlinear Mott-Schottky analysis method. The results showed that the corrosion behavior of 304-stainless steel was affected by various factors, such as pH, chloride ion concentration, and dissolved oxygen. The pit initiation and propagation stage were observed in EIS plots through the addition of sodium chloride. In addition, the effect of pH on the passive film dominated one of the film growth kinetic reactions. The effect of chloride ion concentration was caused by the generation of more cation vacancies, leading the passive film more susceptible to pitting, which was also demonstrated by X-ray Photoelectron Spectroscopy. The results are consistent with the point defect model.     

Corrosion Behavior of Biocompatible Stainless Steels in Physiological Medium for Non‐invasive Diagnosis of Small Fiber Neuropathies Applications

A non‐invasive device based on measurements of electrochemical skin conductance can detect small fiber neuropathy, a sweat gland dysfunction implicated in several diseases. The measurement is related to sweat composition and notably to chloride concentration. To optimize the electrode material, in vitro experiments are performed in mimetic sweat solutions. This work reports on the resistance to pitting corrosion of biocompatible stainless steels (AISI 304L, AISI 430, AISI 430T, D2205) in sweat mimicking electrolyte at pH 7 with variable chloride concentration, to determine the most sensitive material to sweat composition. AISI 430 is promising due to its high sensitivity to chloride concentration variations.     

Corrosion Behavior of Aluminum in Non‐Uniform Electric Fields

The present paper discusses the effect of the geometrical structure of the electric fieldon the corrosion of aluminum cathodes by electrolysis of aqueous solutions of sodium chloride. A correlation between the mass of the aluminum dissolved from the cathode and the factors electric current density, distance between the electrodes, electrolysis time and sodium chloride concentration by electrolysis with direct current in electric fields of various geometries was found.