ICP-AES测定铜电解液中的Fe、Ni、Pb、Bi、Sb、Zn和As

利用ICP-AES分析技术,通过对样品处理、元素分析谱线、酸度等因素进行试验研究,综合确定了分析条件,对铜电解液中杂质元素（Fe、Ni、Pb、Bi、Sb、Zn、As）进行了ICP-AES测定。结果表明,ICP-AES测定铜电解液中Fe、Ni、Pb、Bi、Sb、Zn和As,可以满足铜电解生产的需要,为高纯阴极铜的生产起了指导作用。     

基于元素对研究激光剥蚀-电感耦合等离子体质谱分析硫化物矿物的基体效应

基体效应是影响LA-ICP-MS分析结果准确性的主要因素之一,但目前却没有一种量化基体效应研究的方法。提出了一种以分析元素与内标元素的强度比(I_i/I_is)为纵坐标、浓度比(c_i/c_is)为横坐标绘制I_i/I_is-c_i/c_is图,以元素对I_i/I_is-c_i/c_is图的线性相关系数ｒ量化基体效应的思路。以Fe为内标,考察了13个常用玻璃标准物质与2个硫化物标准及多个硫化物矿物中6个元素对的基体效应,结果显示Cu/Fe和Zn/Fe的线性相关系数r都小于0.99,而痕量元素对Mn/Fe,Co/Fe,Ga/Fe,Pb/Fe的线性相关系数r都大于0.999;以S为内标,考察了2个硫化物标准与多个硫化物矿物中三个主量元素对Fe/S,Cu/S和Zn/S的基体效应,结果显示其线性相关系数r都小于0.999。无论是以Fe为内标结合玻璃标准为外标,还是以S为内标结合硫化物标准为外标分析硫化物矿物,主量元素大多数分析结果的误差大于10%;而以Fe为内标时,绝大多数玻璃标准获得的痕量元素分析结果与MASS-1较为一致,误差小于15%。研究表明,玻璃标准及硫化物矿物标准均与硫化物矿物存在一定的基体效应差异,而采用元素对I_i/I_is-c_i/c_is图的线性相关系数r量化基体效应具有一定的合理性与实用性。研究也表明了以Fe为内标,采用非基体匹配的玻璃标准可用于定量分析硫化物矿物中的痕量元素,尤其是具有较高痕量元素含量的NIST610。     

XRF和LA-ICPMS测定硫化物熔片中的主次量元素

采用高纯HNO₃为氧化剂代替传统的氧化剂,以GeO₂为玻璃化试剂,建立了一种简单、高效的硫化物熔融玻璃片的前处理方法。XRF和LA-ICPMS分析结果表明,相对于粉末压片法,熔片法制备的样品具有更好的均一性和可靠性。3种硫化物国家一级标准物质的XRF和LA-ICPMS主次量元素(Si,Al,Fe,Mg,K,Ca,Na,Mn,Cu,Zn)分析测试结果均与推荐值相吻合(Ti缺少推荐值),测定误差都在允许范围内,XRF三次熔片测试结果的精密度RSD<5.6%;LA-ICPMS 15次测试结果精密度RSD<3%。表明建立的硫化物熔融玻璃片的前处理方法可较好的应用于XRF和LA-ICPMS分析硫化物中的主次量元素。     

Uncertainty and traceability in alloy analysis by borate fusion and XRF

Owing to the increasing demand for compliance with quality system standards, analytical laboratories may need to demonstrate the traceability of their results to the International System of Units (SI) or to the values of a certified reference material. To do that, they need to demonstrate the components of uncertainty in their analytical work. At NIST, the goal is to demonstrate traceability to SI units to ensure that results are accepted on a worldwide basis. For XRF spectrometry with borate fusion, traceability to SI is achieved through calibration with spectrometric solution standards or high‐purity compounds. The method is capable of achieving relative expanded uncertainty estimates (95% confidence level) of 1% or lower. In this paper, the capability is demonstrated for low alloy‐steel and an Al? Ti? Nb? W aerospace alloy. XRF results are compared with certified values and with results from atomic emission methods through a simple bias test. NIST uses the borate fusion/XRF method as part of the value assignment process for Standard Reference Materials^®. Copyright © 2004 John Wiley & Sons, Ltd.     

温控湿法消解ICP-MS测定全血中铅镉硒砷汞5种微量元素

采用温控HNO₃-H₂O₂湿法消解,ICP-MS测定全血中Pb, Cd, Se, As, Hg 5种微量元素的含量。在选定的测试条件下,仪器系统稳定性良好,Pb等5种元素的检出限范围2～40 ng·L-1,全过程中样品均重复测定3次,RSD均在3%内。采用国家全血溶液标准物质GBW(E)09034-09036和人发标准物质GBW09101b中的相应元素进行质量控制,检测结果和推荐值相吻合。同时,应用本方法实测了湘西汞矿区34名村民全血中的5种元素的含量,结果表明：矿区村民Se和As处于正常水平,血Pb、血Cd、血Hg含量均偏高,有较高的健康风险,应当引起有关部门的重视。本方法快速、灵敏,精密度及准确度均符合要求,适于人体全血样中Pb, Cd, Se, As, Hg等微量元素的测定。     

X荧光能谱法测定合金结构钢标样中五个元素

本文提出Ｘ荧光能谱法测定合金结构钢中５个元素含量的方法。本方法采用能说仪中定量分析软件，选择适当工作条件，测定合金结构钢中５个元素。其准确度精确度均能满足分析要求。     

ICP-AES测定镁合金中的Zn、Mn、Zr、Ce

采用ICP－AES测定了镁合金中的Zn、Mn、Zr、Ce，进行了酸度试验，氢氟酸用量试验，分析线的选择，并研究了基体元素对待测元素的干扰。测定值与标钢值吻合较好，RSD＜5％。方法简便可靠，可获得令人满意的分析结果。     

表面电荷法平面元电荷系数的半解析解法

针对在线性及高次电荷估计下,表面电荷法中全解析法对平面元电荷系数求解和实现较复杂的问题,提出一种半解析法.将系数积分由局部坐标系变换到整体坐标系下分离参数的二重积分,利用内层积分存在解析解的特点,将二维问题降为一维,方便数值积分计算.对于对数奇异积分问题采用辅助函数法消除.通过算例与全解析法计算精度进行比较,结果表明,在一定的单元划分下,可达到很高精度,具有一定可行性.     

Trace detection of light elements by laser-induced breakdown spectroscopy (LIBS): Applications to non-conducting materials

The existence as well as concentration of light (low-atomic number) elements is directly related to some of the most important properties of almost all materials. Thus, the development of a direct, fast, and sensitive spectroscopic method for the analytical quantification of these elements is considered an important continuing challenge in many fields. In this report, results obtained from previous as well as most recent studies regarding trace detection of light elements in non-conducting materials by laser-induced breakdown spectroscopy (LIBS) technique are reviewed for the first time. Firstly, we introduce investigations performed in the far- and vacuum-UV as well as UV-visible-NIR spectral domains, and cover many non-conducting materials including gases, aerosols, soil, cement, and selected organic compounds. The report also demonstrates important analytical results for the elements lithium, beryllium, boron, carbon, fluorine, phosphorus, sulfur, and chlorine. In addition, key characterization information relating to a specific element in a given matrix and state is summarized in such a way that relevant resources can easily be traced. Furthermore, in order to facilitate tracking down the evolution of the technique for a particular material category, a chronological order has been devised. In the second part of the review, the latest developments and advances in instrumentation and methodologies of the LIBS technique, particularly in the realm of light elements detection, are discussed. The sensitive detection of light elements in the UV-VIS-NIR is still unsatisfactory, and more work is needed in order to achieve better analytical performance in terms of precision, accuracy and limits of detection. The author anticipates that significant sensitivity improvements should be realized by combining LIBS, employing femtosecond laser pulses, with other diagnostic techniques based on probing the plasma via diode lasers.     

电感耦合等离子体串联质谱法测定野生皂荚中多种微量元素

采用电感耦合等离子体串联质谱(ICP-MS/MS)法测定野生皂荚中多种微量元素的含量。皂荚样品以HNO₃+H₂O₂+HCl为混合消解试剂经微波消解后直接测定。在MS/MS模式下向碰撞反应池中通过氧气或氨气,分别利用氧气质量转移、氧气原位质量和氨气质量转移消除多原子离子质谱干扰。通过分析国家标准参考物质绿茶(GBW10052)和芹菜(GBW10048)验证方法的准确性和精密度,所测定结果与参考值基本一致,RSD≤7.8%。采用所建立的方法分别分析了来自中国云南和重庆武陵山区野生皂荚中的12种微量元素(V,Cr,Co,Cu,Zn,Fe,Mn,Ni,As,Cd,Hg,Pb),12种微量元素的检出限为0.29～21.36 ng·L-1。结果显示,野生皂荚12种分析元素中Fe含量最高,其次为元素Zn,重金属元素As,Cd,Hg和Pb的含量远低于《中国药典》限量标准。该研究为野生皂荚中微量元素的安全评价和监管提供了科学方法和数据。     

An alternative method for the determination of element concentrations in schizophrenic, lung cancer and leukaemia patient bloods

Concentration of the elements present in schizophrenic, lung cancer and leukaemia patients’ bloods were determined using energy-dispersive X-ray fluorescence (EDXRF) method. EDXRF spectrometer with an annular and sources was applied for the analysis of blood samples. A sample preparation procedure suitable for the EDXRF, the experimental approach, analytical method used in this study and the results were presented. EDXRF technique has been successfully used for the determination of elements present in blood.     

Determination of the Biodiesel Content in Diesel/Biodiesel Blends: A Method Based on Fluorescence Spectroscopy

Blends of biodiesel and diesel are being used increasingly worldwide because of environmental, economic, and social considerations. Several countries use biodiesel blends with different blending limits. Therefore, it is necessary to develop or improve methods to quantify the biodiesel level in a diesel/biodiesel blend, to ensure compliance with legislation. The optical technique based on the absorption of light in the mid-infrared has been successful for this application. However, this method presents some challenges that must be overcome. In this paper, we propose a novel method, based on fluorescence spectroscopy, to determine the biodiesel content in the diesel/biodiesel blend, which allows in loco measurements by using portable systems. The results showed that this method is both practical and more sensitive than the standard optical method.     

凝胶电泳与激光剥蚀-电感耦合等离子体质谱联用测定蛋白质中微量元素的应用进展

介绍了凝胶电泳(GE)和激光剥蚀-电感耦合等离子体质谱(LA-ICP-MS)联用测定蛋白质中微量元素的方法,对蛋白质分离、凝胶处理,包括染色及干燥,和检测过程中的定量校正等技术问题做了详述,并综述了LA-ICP-MS在硒蛋白、磷酸化蛋白及金属蛋白分析中的应用,指出了这种方法在蛋白质中微量元素检测中存在的问题和发展方向。     

火焰原子吸收光谱法测定硝酸铑中的铜、铅、钠和铁

硝酸铑液体样品,加硝酸酸化定容后,无需分离富集,采用快速火焰原子吸收光谱法同时测定其杂质元素铜、铅、钠和铁含量,方法简便,快速,可满足实际生产质量监控过程需求。     

X射线荧光光谱法同时测定电子电气产品中限制使用物质铅、汞、铬、镉和溴

提出了用X射线荧光光谱法同时测定电子电气设备中限制使用物质铅、汞、铬、镉和溴的一种新的测试方法。研究了金属材料基体、聚合物基体和不同电子产品等基体对待测元素的影响,研究了元素间谱线重叠所产生的光谱干扰,考察了样品大小不同和样品厚度不同对待测元素测试结果的影响,并选用Rh线的康普顿散射线作内标来校正这些非光谱干扰的影响。选用自制的参考物质制作工作曲线,各待测元素的浓度范围从最低测定下限100到1 500 mg·kg-1,均获得非常好的线性关系。选用有证标准物质BCR-681,并设置100 s测量时间来计算铅、汞、铬、镉和溴的最低检出限,其检出限分别为Pb L_β 0.64 mg·kg-1,Hg L_α 0.51 mg·kg-1,Cr K_α 0.78 mg·kg-1,Cd K_α 1.10 mg·kg-1和Br K_α 0.27 mg·kg-1。以BCR-681作为实际样品进行测试,其结果与标准推荐值非常吻合。     

Fermion Particle Production in a Periodic Potential

In this paper we study fermion particle production in the early universe. The present work is motivated to restudy the fermion particle production from the basics and compare the results in the literature through another method developed by one of the present author. One of the authors (SB) has developed a method, known as complex trajectory WKB method, to study particle production in curved as well as flat spacetime. In the present work we have tried to compare the CWKB method with that of other works, current in the literature. In this work we have obtained the particle production amplitude starting from the basics and test our results through both analytical and numerical calculations. For fermion particle production, we first do analytical calculations with a toy example to calculate the production amplitude and verify the same doing fourth order Runge-Kutta calculation. As most problems relevant to early universe are not amenable to analytical calculations, we then take up to study the particle production in periodic potential, generally used in inflationary cosmology. We recheck two recent approaches and obtain almost identical results as that obtained by Greene and Kofman. We also verify the result through CWKB method. Boson particle production has been discussed elsewhere, we discuss it briefly in connection with CWKB. In the present work we generalize the CWKB results of boson production to fermion production. Our works will enable one to understand the various phenomena in early universe related to particle production. Using CWKB we calculate the occupation number and some other results for fermion particle production. The present work will help us clarify the variant results of fermion production current in the literature.     

Determination of essential elements (Mn,Fe, Cu and Zn) in herbal teas by TXRF,FAAS and ICP-OES

The aim of this study was the comparison of the results obtained in the determination of the content of essential elements such as Mn, Fe, Cu and Zn in vegetation samples using different analytical approaches, including suspension preparation and total reflection X-ray fluorescence ( TXRF) analysis as well as most commonly used spectroscopic methods in the field of vegetal analysis such as acid digestion in combination with atomic emission (AES) and atomic absorption spectrometry (AAS). In the case of TXRF analysis, two instruments equipped with different X-ray tubes anodes (W and Mo) were used to better evaluate the potential of TXRF for vegetal samples analysis. Analytical figures of merit for the considered methods were determined by the analysis of plant reference materials. The one-way analysis of variance (ANOVA) applied to the analysed and certified values showed that the results were not statistically different at the significance level of p-values <0.05. Therefore, suspension preparation and TXRF analysis proved to be a sustainable and fast analytical alternative to the most commonly used ones involving a previous digestion of the sample and inductively coupled plasma optical emission spectrometry (ICP-OES) or flame atomic absorption spectrometry (FAAS) analysis. Finally, the different analytical approaches were applied to the determination of Mn, Fe, Cu and Zn in a set of herbal teas used for medical purposes.     

A multi-technique chemical characterization of a Stradivari decorated violin top plate

This paper focuses on the characterization of the materials of a violin top plate made by Antonio Stradivari (17th century), with different diagnostic techniques and with an integrated and non-destructive analytical methodology to study surface coatings and decorations. The UV-induced visible fluorescence, optical digital microscopy, ED-XRF associated with micro-FTIR spectroscopy analysis, and dendrochronology were performed. The investigations were aimed to identify the presence of original varnish layers and to characterize the composition of the decorations, either the inlaid purflings or the composite false-inlay strip between them. Several results were achieved: (i) evidence of the absence of varnish layers on the surface as a result of extended and inappropriate restoring; (ii) identification of the dye used for the black layers of the purflings; (iii) characterization of the black matrix and the white elements of the decoration. Furthermore, a dendrochronological dating was performed. A copy of the top plate was realized with materials similar to those identified on the Stradivari original; the same analyses performed on the original model were carried out on the same areas of the copy.     

ICP-AES法检测云南稻精米和糙米与土壤矿质元素间的关联性

采用电感耦合等离子体原子发射光谱法(ICP-AES)对55个云南省水稻改良品种精米、糙米及其相应的土壤18种矿质元素进行测定与分析, 加标回收率在93.1%～110.2%之间, RSD为0.8%～5.1%。18种矿质元素(S, Mo, Ba, Ni, Fe, Cr, Na, Al, Cu, P, Sn, Zn, B, Mn, Mg, Ca, Sr和K)是功能稻米活性成分的重要部分,精米的平均含量依次为P>K>S>Mg>Ca>Zn>Na>Al>Mn>Fe>Cu>B>Mo>Ni>Sn>Cr>Ba>Sr, 糙米P>K>Mg>S>Ca>Zn>Mn>Al>Na>Fe>Cu>B>Mo>Sn>Ni>Cr>Ba>Sr, 而土壤则为Fe>Al> Ca>K>Mg>P>S>Mn>B>Na>Ba>Zn>Cr>Cu>Ni>Sn>Mo>Sr;精米和糙米除S和P外, 16种矿质元素含量均明显低于土壤;精米和糙米间八种微量元素(Mo, Ni, Cr, Sr, Mn, Zn, Cu, Na)间相关性明显比六种宏量元素(P, K, Mg, Ca, S和Al)间关系密切。云南土壤以富铁铝高钙为主而精米和糙米则以磷钾镁硫为主;以精米为主食比糙米更易诱发慢性病。文章结果可能为功能稻米遗传育种、生产以及人类慢性病和矿质营养不良(Fe, Zn和Ca)问题研究的参考。     

用扫描式电感耦合等离子体光谱仪测定红矾钾产品中的杂质

应用电感耦合等离子体发射光谱法测定了铬盐清洁工艺红矾钾产品中的微量元素硅、铝、铁、钙、锰、镁和氯。采用基体匹配法消除了大量基体的干扰。实验的优化条件为RF发生器的入射功率095kW;载气压力013MPa,流量12L·min-1;辅助气流量02L·min-1。元素氯用氯化银沉淀间接测定,在6%的硝酸体系中氯离子形成氯化物完全沉淀,在50℃陈化2h后进行测定。样品的加标回收率在90%～104%,RSD<4%,检出限在10-4%～10-5%。随机抽样的分析结果与标准加入法吻合较好,相对误差在-427%～ 526%。本方法用于实际样品分析,快速简单,结果令人满意。