Preparation and hydrogen permeation properties of BaCeo.95Nd0.05O3-δ membranes

Dense mixed proton and electron conducting membrane made of BaCe0.95Nd0.05O3-δ （BCNd5） was prepared by pressing followed by sintering. X-ray diffraction （XRD） was used to characterize the phase structure of both the powder and the sintered membranes. The microstructure of the sintered membranes was studied by scanning electron microscopy （SEM）. Hydrogen permeation through the BCNd5 membrane was studied using a high temperature permeator. The hydrogen permeation fluxes under wet conditions are higher than those under dry conditions, which is due to H^＋ hopping via surface OH groups. At 925℃, a hydrogen permeation flux of 0.02 mL/min cm^2 was obtained under wet condition, which recommends BCNd5 as a potential material for hydrogen-selective membranes.     

Thermal Behavior and Decomposition Kinetics of the Complexes of CuX2 （X=NO3, Br, CI and CIO4） with 3,3＇-Dimethyl-1 -（1 H-1,2,4-triazol-1-yl）-2-butanone

The thermal behaviors of the complexes of Cu(DMTZB)4X2 (DMTZB=3,3‘-dimethyl-1-(1H-1,2,4-triazol-1-yl)-2-butanone, X=NO3 or ClO4) and Cu(DMTZB)2 X2 (X=Br or Cl) in a nitrogen atmosphere were studied under the non-isothermal conditions by simultaneous TG-DTG-DSC, EDS and elemental analysis techniques. The resuits showed that their decomposition proceeded in three different ways mainly depending on the anions in the molecules. The heat effect associated with the decomposition step of DMTZB molecules was also different. The decomposition mechanisms and the kinetic parameters of DMTZB were determined and calculated by jointly using four methods, which showed that its pyrolysis was controlled by D3 mechanism but with different activation energies and pre-exponential factors for different complexes.     

Improvement in Toughness of Polylactide by Melt Blending with Bio-based Poly（ester）urethane

Polylactide （PLA） was successfully toughened by blending with bio-based poly（ester）urethane （TPU） elastomers which contained bio-based polyester soft segments synthesized from biomass diols and diacids. The miscibility, mechanical properties, phase morphology and toughening mechanism of the blend were investigated. Both DSC and DMTA results manifested that the addition of TPU elastomer not only accelerated the crystallization rate, but also increased the final degree of crystallinity, which proved that TPU has limited miscibility with PLA and has functioned as a plasticizer. All the blend samples showed distinct phase separation phenomenon with sea-island structure under SEM observation and the rubber particle size in the PLA matrix increased with the increased contents of TPU. The mechanical property variation of PLA/TPU blends could be quantitatively explained by Wu＇s model. With the variation of TPU, a brittle-ductile transition has been observed for the TPU/PLA blends. When these blends were under tensile stress conditions, the TPU particles could be debonded from the PLA matrix and the blends showed a high ability to induce large area plastic deformation before break, which was important for the dissipation of the breaking energy. Such mechanism was demonstrated by tensile tests and scanning electron microcopy （SEM） observations.     

Synthesis and characterization of HPMA copolymer-5-FU conjugates

N-（2-Hydroxypropyl） methacrylamide copolymer-5-fluorouracil （PHPMA-FU） conjugates were synthesized by a novel and simplified synthetic route, and characterized by UV, FTIR and HPLC analyses. The conjugated content of 5-fluorouracil （5-FU） was 3.41 ± 0.07 wt%. The stabilities of PHPMA-FU conjugates under different conditions were studied. The results showed that HPMA copolymer was a potential carrier for tumor-targeting delivery of 5-FU.     

Efficient synthesis of chromenopyridine and chromene via MCRs

MCRs for preparation of chromenopyridines under reflux conditions and chromenes at room temperature conditions from different salicylaldehydes,malononitrile and different thiols（mol ratio- 1：2：1） were established.Mechanistic investigation suggests that the MCRs undergo different pathways at different temperatures and catalyzed by different organic bases.The structure of chromenopyridine and chromene are confirmed by crystal X-ray crystallography.     

The efficient synthesis of 14-alkyl or aryl 14H-dibenzo[a,j]xanthenes catalyzed by bismuth(Ⅲ)chloride under solvent-free conditions

An efficient method for the synthesis of 14-alkyl or aryl 14H-dibenzo[a,j]xanthene derivatives by the reaction of β-naphthol,and aldehydes in the presence of a catalytic amount of bismuth（Ⅲ） chloride（BiCl₃） under solvent-free conditions at 110℃is described.Aliphatic and aromatic aldehydes were used in the reaction and in all cases the desired products were synthesized successfully.This reaction was studied under different temperatures;the maximum yield was obtained in a short reaction period at 110℃.The method offers the advantages of high yields,short reaction times,simplicity and easy workup compared to the conventional method of syntheses.     

Conformation Analysis and Comparison of Epristeride（ 17β- N-t-Butylcarboxamide-androst-3,5-diene-3-carboxylic Acid） and Its Analogs

Conformations of Epristeride（ 17-β-N-t-butylcarboxamide-androst-3,5-diene-3-carboxylic acid） and its analogs were analyzed with the random search method and compared by means of the methods for steroid conformers, Connolly surfaces, dihedral angles, and molecular accessibility probes with protons, hydroxyl and methyl groups contained simultaneously. Analog d is different from others, which is in accordance with the preliminary clinical trial results under double blind conditions.     

A Convenient Synthesis of Novel Meldrum＇s Acid C60 Fullerene Derivatives

A series of novel Meldrum＇s acid C60 derivatives were prepared in moderate yields from a convenient one-pot reaction of C60, the Meldrum＇s acid derivatives, 12 and 1,8-diazabicyclo-[5,4,0]-undec-7-ene （DBU） in toluene at room temperature under nitrogen atmosphere. All the new compounds were fully characterized by the spectral data and elemental analysis. A carbene intermediate mechanism was proposed for this reaction.     

Thermal Kinetics and Decomposition Mechanism of Methylphenylphosphinic Acid and Diphenylphosphinic Acid

Thermal degradation and degradation kinetics of methylphenylphosphinic acid（MPPA） and diphenyl- phosphinic acid（DPPA） were investigated via thermogravimetric analysis（TGA） technique under non-isothermal conditions. The activation energies of the decomposition process for the two compounds were calculated through the Friedman and Kissinger-Akahira-Sunose（KAS） methods. The thermal decomposition mechanism was investigated by the Criado method based on a set of TGA data obtained at different heating rates. It was shown that the activation energies calculated from the decomposition reaction by different methods were consistent with each other. The results show that the probable model for the degradation of MPPA and DPPA agreed with the two-dimensional（D2） and three-dimensional（D4） diffusion models, respectively. Moreover, the thermodynamic functions（△H, △S, △G） of the two decomnosition reactions were also calculated.     

An Unexpected and Green Synthetic Protocol for Ethyl 1‐Aroyl/Aroylmethyl‐5‐methyl‐3‐methylthiopyrazole‐4‐carboxylates: High Regioselectivity in Alkylation and Acylation Reactions between N‐1 and N‐2 of a Pyrazole Ring

Two series, totaling twelve, of new compounds, ethyl 1‐aroyl/(aroylmethyl)‐5‐methyl‐3‐methylthiopyrazole‐4‐carboxylates ( 5 / 6 ), have been synthesized via highly regioselectively acylation and alkylation reactions of ethyl 3‐methyl‐5‐methylthio‐1 H‐pyrazole‐4‐carboxylate ( 2a ) with aroyl chloride ( 3 ) and eco‐friendly reagents alpha‐tosyloxysubstituted acetophenones ( 4 ), respectively, and a green protocol has been developed. The acylation reactions were carried out under ultrasound irradiation, and the alkylation reactions were under microwave irradiation and ultrasound irradiation, respectively. Conventional reaction conditions, as well as the use of alpha‐bromosubstituted acetophenone ( 4 ′) have also been applied in the synthesis of some randomly selected compounds in both series and have generated identical compounds correspondingly. Unexpected structures of compounds were unambiguously determined by X‐ray crystallographic analysis.     

Rational synthesis of multicyclic bis[2]catenanes

Bis-loop tetraurea calix[4]arene 6 has been prepared by acylation of the wide-rim calix[4]arene tetraamine 1 with the activated bis(urethane) 8 under dilution conditions. Similarly the bis(Boc-protected) tetraamine 2 is converted into the mono-loop derivative 3 which after deprotection and acylation gives the bisalkenyl derivative 5. In apolar solvents this tetraurea calix[4]arene 5 forms regioselectively a single hydrogen-bonded homodimer, from which the bis[2]catenane 10a is formed in 49% by a metathesis reaction followed by hydrogenation. Bis-loop derivative 6 forms no homodimers for steric reasons, but a stoichiometric mixture with the open-chain tetraalkenyl derivative 7a contains exclusively the heterodimer. Metathesis and subsequent hydrogenation now yields 65 % of the pure bis[2]catenane 10a which could not be isolated from the complex reaction mixture obtained from the homodimer 7a.7a. The chirality of 10a (D(2) symmetry) has been verified by optical resolution using HPLC on a chiral stationary phase.     

Studies on pyrazine. 23 . Homolytic acylation of 2-amino-3-cyanopyrazine and the related compounds with α-keto acids: A synthesis of 5-acyl-3-aminopyrazinecarboxylic acid derivatives

Homolytic acylation of 2-amino-3-cyanopyrazine (1) with α-keto acids led to the formation of 6-acylated compounds in 74-85% yields. Methyl 3-aminopyrazinecarboxylate (2) and 3-aminopyrazinecarboxamide (3) were also acylated under the same conditions although in lower yields. The observed reactivity of acylation is explained by comparison with the homolytic reactions of related pyrazines.     

Synthesis of fluorine-containing betulin esters

28-O-Fluoroacylbetulins were synthesized via acylation of betulin by fluorocarboxylic (perfluorobutyric, perfluorooctanoic, 3-fluorobenzoic, perfluorobenzoic) acid chlorides in CHCl₃ in the presence of Py. 3,28-Di-O-fluoroacylbetulins were prepared by treatment of betulin with fluorocarboxylic (trifluoroacetic, pentafluoropropionic) acid anhydrides in Py in the presence of 4-dimethylaminopyridine. 3,28-Di-O- (3-fluorobenzoyl)betulin was obtained from acylation of betulin by 3-fluorobenzoic acid in CH₂Cl₂ in the presence of N,N′-dicyclohexylcarbodiimide and 4-dimethylaminopyridine whereas acylation by perfluorobutyric acid under the same conditions gave 28-O-perfluorobutanoylbetulin.     

Synthesis of methyl 3-amino-4-aryl(or methyl)sulfonyl-2-thiophenecarboxylates from 3-alkoxy-2-aryl(or methyl)-sulfonylacrylonitriles

The synthesis of a series of methyl 3-amino-4-aryl(or methyl)sulfonylthiophene-2-carboxylates by reaction of 3-alkoxy-2-aryI(or methyl)sulfonylacrylonitriles with methyl thioglycolate in the presence of triethylamine is described. Hydrolysis/decarboxylation of the ester at the 2-position and acylation of the resulting amine represents a convenient route to 4-arylsulfonyl-3-carboxamidothiophenes. Attempted acylation of a title aminothiophene under standard conditions was unsuccessful.     

PMP的酰化反应及其产物萃取性能的研究

合成了9个新1-苯基-3-甲基-5-吡唑酮(PMP)的烷氧基苯酰基衍生物.PMP在不同条件下的酰化研究表明酰氯的量和碱的性质和量对反应方向有很大影响.并用5个C-烷氧基苯酰基PMP衍生物做了萃取La(III)和Y(III)离子的试验,发现1-苯基-3-甲基-4-(3,4,5-三甲氧基)苯甲酰基-4-吡唑酮的萃取性能优于PMBP.     

Effects of acyl donor type, catalyst type, and reaction conditions on the activity and selectivity of Friedel-Crafts acylation

Acylation of anisole and 3-methylanisole was performed with several acylating reagents (acetylation by AcCl and Ac₂O and bromoacetylation by BrAcCl and (BrAc)₂O) over different solid acid catalysts. The reaction conditions were optimized with respect to the acylation reagent, overall yield, solid acid catalyst, and the products selectivities. While acylation of anisole with acetyl chloride or acetic anhydride resulted in its full conversion to para-substituted acetophenone, the use of bromoacetyl bromide or bromoacetic anhydride yielded also the ortho-substituted product. Acylation of 3-methylanisole also yielded both para- and ortho-substitutions, and the products distribution was affected by the reaction conditions and catalyst type. It was found that while more acidic catalysts (caesium salt of heteropolyacid and zeolites) were the most active towards anisole acylation, the most active catalysts for the acylation of 3-methylanisole were ion-exchange catalysts. Employing HY-740 zeolite resulted in the highest ortho-selectivity in the acylation of anisole with bromoacetyl bromide and bromoacetic anhydride and in the acylation of 3-methylanisole with acetic anhydride.     

Studies on O-,N-Acylation of 3-Hydroxyisoxazole and Their Regioselective Synthesis(Ⅰ)——O-,N-acylation of 5-Methyl-3-hydroxyisoxazole with 2,2-Dimethyl 3-Substituted Cyclopropanecarboxylic Chlorides

The reactions of 5-methyl-3-hydroxyisoxazole with 2, 2-dimethyl, 3-substituted cyclopropanecarboxylic chlorides give O-acyl-5-methyl-3-hydroxyisoxazole and N-acyl-5-methylisoxazolin-3-one derivatives. The ratio of O-acyl to N-acyl product depends upon the acylation reagents. O-acyl derivatives can be converted to the N-acyl compounds by isomerization under acidic conditions or heating.     

Acylation of Alcohols and Amines with Vinyl Acetates Catalyzed by Cp(2)Sm(thf)(2)

Cp(2)Sm(thf)(2) was found to be an efficient catalyst for the acylation of alcohols and amines with esters under mild conditions. In the present acylation, vinyl and isopropenyl acetates served as good acylating agents. Thus, a variety of alcohols and amines underwent acylation with vinyl and isopropenyl acetates in the presence of Cp(2)Sm(thf)(2) to give the corresponding esters and amides in good to excellent yields. This catalytic acylation of alcohols and amines offers an additional useful method by the use of various esters, instead of acid anhydrides and acid chlorides, as acylating agents under very mild conditions.     

3-羟基异恶唑的O-和N-酰化及其区域选择性研究 Ⅱ.3-羟基-5-甲基异恶唑O-和N-酰化产物的选择性合成

本文研究了不同反应条件下3-羟基-5-甲基异恶唑(1)与3-甲基-2- 对氯苯基丁酰氯(2a)的反应,提出了区域选择性合成O-和N-酰化产物的方法.在三乙胺存在下,乙腈为溶剂,1和2a～2e反应得到含量为88～96%的O-酰化产物3a～3e,而若将1 转化为相应的异恶唑硅醚4,再与2a～2i反应,则得到含量为86～97%的N-酰化产物5a～5i.试验表明,在DMAP催化下,3a和5a可发生O-/N-酰基转移反应