平行双铂丝微电极的制作及特性研究

本文首次报道了平行双铂丝微电极的制作方法。并用循环伏安法和计时电流法对其特性进行了研究。实验表明,不同工作方式下电极呈现不同的响应,对于可逆氧化还原物质,当电极在产生—收集方式时,电流成倍增加,达到稳态电流时间大大缩短。本文还研究了这种电极对铁氰化钾的线性响应范围和检出限,对其工作原理也进行了初步探讨。     

二茂铁修饰碳黑微电极同时测定多巴胺和抗坏血酸

研究了神经递质多巴胺(DA)和抗坏血酸(AA)在二茂铁修饰碳黑微电极上的电化学行为。实验结果表明,在pH4.5的磷酸盐中,DA在该电极上的线性范围为2.0×10-6～4.0×10-3mol/L,检出限(3σ)为1.0×10-6mol/L;AA在该电极上的线性范围为6.0×10-6～1.0×10-3mol/L,检出限(3σ)为2.0×10-6mol/L;用这种电极可以同时测定多巴胺,抗坏血酸。     

聚氨基乙酸修饰碳黑微电极同时测定多巴胺和抗坏血酸

用电化学方法将氨基乙酸聚合在碳黑微电极表面制得聚氨基乙酸修饰碳黑微电极,并用循环伏安法在pH 7.0的磷酸盐缓冲介质中,研究了该修饰电极的电化学行为.结果表明:在此缓冲介质中,多巴胺和抗坏血酸经在-200 mV(vs.SCE)富集30 s后,在此修饰电极上发生催化氧化反应,并分别在320 mV及42 mV处呈现各自的峰电位(Epa),在多巴胺和抗坏血酸的I″p值及其浓度之间分别在2.0×10-8～1.0×10-4mol·L-1,4.0×10-7～1.0×10-3mol·L-1范围呈线性关系,检出限(3σ)分别为6.0×10-9mol·L-1及1.0×10-7mol·L-1.此修饰电极有良好的重复性和稳定性,只需将用过的电极在400 mV置于同一缓冲溶液中清洗0.5～2.0 min,即可方便地再生恢复原有性能.应用此方法分析了含有多巴胺及抗坏血酸的混合溶液,测定结果的相对标准偏差(n=7)在1.6 9,6～2.6%之间,回收率在96%～104%之间.     

电化学活化碳纤维微电极和脑神经递质及抗坏血酸在体测定

本文采用一种简单电化学方法,即恒电流法处理自制碳纤维电极,在脑神经递质测定中显示了很高的灵敏度和分辨能力.活化后的电极对多巴胺的检测限达5×10^-8mol.dm^-3,对多巴胺和抗坏血酸的伏安峰分离达170mV.作者使用该电极,采用半微分伏安法测定了活体大鼠脑内抗坏血酸,3,4-二羟苯乙酸和5-羟吲哚乙酸的浓度分别为1.7×10^-4,2.1×10^-5和 3.3×10^-6mol·dm^-3.本文对电极的制作,活化条件,伏安峰判别,在体药物实验和电极活化机理等进行了研究和探讨.     

果蔬中L—抗坏血酸的示波计时电位K3Fe（CN）6滴定法研究

本文报导的方法是在南京大学高鸿教授研究的K_3Fe(CN)_6示波极谱滴定法(在PH8的K_2HPO_4—KH_2PO_4—KBr底液中,用0.04660mol/LK_3Fe(CN)_6标准溶液对纯抗坏血酸测定)的基础上,考虑到L—抗坏血酸(以下简称V_e)在碱性、中性介质中稳定性差,如用于V_e含量很微的果蔬测定,对结果影响大。本文改为H_2C_2O_4—KBr的酸性介质作底液,用     

双柱碳纤维微电极的研究及其在测定多巴胺中的应用

报道了双柱微电极的制作方法,提出了用双柱碳纤维微电极在抗坏血酸存在下选择性地测定多巴胺.探讨了电极反应机理.多巴胺的浓度在5.0×10^-4～5.0×10^-6mol/L范围内与收集电流成正比.抗坏血酸浓度<5.0×10^-4mol/L时对测定结果无影响.     

库仑滴定法测定Vitamin C片及黄瓜、青椒中抗坏血酸的含量

建立了以1.0 mol.L-1碘化钾和1.0 mol.L-1醋酸混合液作为电解液的恒电流库仑滴定法测定抗坏血酸含量的方法。结果表明,方法的回收率在98.3%~100.8%之间,RSD在0.21%~0.56%(n=3)。该法可直接用于V itam in C片及黄瓜、青椒等样品中抗坏血酸含量的测定,方法简便灵敏,结果令人满意。     

伏安型植物组织生物微电极的研究——茄子组织碳糊微电极的研究

茄子组织生物微电极在儿茶酚测定中表现出了较高的生物催化活性,而对抗坏血酸测定则为稳态响应,这表明该电极能有效地消除抗坏血酸的干扰。该电极的灵敏度高,重现性好,对多巴胺测定的线性范围为5.8×10~(-6)～6.5×10~(-4)mol/L,检出下限为:2.9×10~(-6)mol/L。     

维生素C的交流示波极谱滴定分析

在盐酸介质中 ,用K3 [Fe(CN) 6]标准溶液直接滴定Vc,以K3 [Fe(CN) 6]在交流示波极谱图上的切口出现指示滴定终点 .本法操作简便 ,灵敏准确 ,选择性强 ,应用于单方药物制剂Vc片剂和复方药物制剂感冒敏以及强力Vc银翘片中Vc的含量测定 ,结果满意     

Gold Nanoparticles Modified Titania Nanotube Arrays for Amperometric Determination of Ascorbic Acid

Development and use of highly ordered, vertically aligned TiO₂ nanotube arrays modified with gold nanoparticles for the selective detection of ascorbic acid (AA) in the presence of uric acid and glucose are reported here. Gold nanoparticles were electrodeposited on the Nanotube arrays by CV. The sensor was characterized using SEM, EDS, CV, and EIS. It showed very good performance with a sensitivity of 46.8 μA mM^?1 cm^?2, response time below 2 seconds and linearity in the range of 1 μM to 5 mM with a detection limit of 0.1 μM and was tested for the AA concentration in pharmaceutical preparations.     

Electrooxidation and Amperometric Detection of Ascorbic Acid at GC Electrode Modified by Electropolymerization of N,N‐Dimethylaniline

The polymer film of N,N‐dimethylaniline (DMA) is deposited on the electrochemically pretreated glassy carbon (GC) electrode by continuous electrooxidation of the monomer. This poly N,N‐dimethylaniline (PDMA) film‐coated electrode can be used as an amperometric sensor of ascorbic acid (AA). The polymer film (thickness (?): 0.3±0.02 μm) having positive charge in its backbone attracts the anionic species AA. Thus, the anodic peak potential (350 mV vs. Ag|AgCl|NaCl_(sat)) for the oxidation of AA at the bare electrode is largely shifted to the negative value (150 mV) at this electrode. The PDMA film‐coated electrode is stable in acidic, alkaline and neutral media and can sense AA at different pH's. The diffusion coefficients of AA in solution (D) and in film (D_s) were estimated by rotating disk electrode voltammetry: D=(5.5±0.1)×10^?6 cm² s^?1 and D_s=(6.3±0.2)×10^?8, (6.0±0.2)×10^?8 and (4.7±0.2)×10^?8 cm² s^?1 for 0.5, 1.5 and 3.0 mM AA, respectively. A permeability of AA through the PDMA film was found to decrease with increasing the concentration of AA in the solution. In the chronoamperometry, the current response for the oxidation of AA at different times elapsed after potential‐step application is linearly increased with the increase in AA concentration in a wide range of its concentration from 25 μM to 1.65 mM. In the hydrodynamic amperometry, a successive addition of 10 μM AA caused the successive increase in current response with equal amplitude and the sensitivity was calculated as 0.178 μA cm^?2 μM^?1. So, the fouling of the electrode surface caused by the oxidized product of AA is markedly eliminated at this PDMA film‐coated electrode. A flow injection analysis based on the present electrode was performed to estimate the concentration of vitamin C in fruit juice.     

Congo Red Immobilized on a Silica/Aniline Xerogel: Preparation and Application as an Amperometric Sensor for Ascorbic Acid

Congo red (CR) was immobilized on a silica/aniline xerogel through electrostatic interaction. The dye is strongly retained and is not easily leached from the xerogel matrix. The material containing the adsorbed dye was used to prepare a carbon paste electrode and the electrochemical properties of the hybrid material were investigated using cyclic voltammetry and amperometry. The modified electrode was used to study the electrochemical oxidation of ascorbic acid. The adsorbed dye mediates ascorbic acid oxidation at the solid electrode surface‐solution interface at an anodic potential of 0.18 V at pH 7, in a 0.5 mol L^?1 KCl solution. This novel modified carbon paste electrode shows good analytical performance for the determination of ascorbic acid in commercial Vitamin C tablets.     

A New Redox Reaction of Ascorbic Acid at Platinum Electrodes

A pair of new redox peaks of ascorbic acid at a platinum electrode was found and studied in detailed by spectroelectrochemistry and electrochemistry technologies. This is a quasi‐reversible redox reaction with a one‐electron transfer process. The intermediate of tertiary carbon free radical exists in this process. The appearance reaction rate constant and the diffusion coefficient were investigated. A possible reaction mechanism has been proposed.     

Determination of Ascorbic Acid by a Composite-Modified Platinum Electrode

Thin composite layers of poly(3,4-ethylenedioxythiophene) and poly(4-lithium styrene sulfonic acid) were formed on a platinum surface. The modified electrode platinum/polyethylenedioxythiophene:poly(4-lithium styrene sulfonic acid) was characterized by cyclic voltammetry, chronocoulometry, and electrochemical impedance spectroscopy. The results showed that the electrode may be used as a working electrode for electroanalytical methods. This electrode was used for the determination of ascorbic acid. The effect of composite layer thickness on the functionality of the electrode was characterized for ascorbic acid determination. Another investigated aspect was the process of ascorbic acid oxidation in solutions of various pH values. The results showed that the modified electrode was suitable for the determination of ascorbic acid in various electrolytes from pH 2 to 7.6 in the presence and absence of buffer solutions. The linear dynamic range of ascorbic acid concentrations corresponded to its concentrations in physiological fluids.     

Determination of Diaryliodonium Species by Reverse Iodometric Titration with Ascorbic Acid

Diaryliodonium salts are used in organic chemistry, materials science and pharmaceutical chemistry. For the quantitative analysis of diaryliodonium salts, only instrumentally demanding techniques requiring highly skilled operators are available. Surprisingly, no titration method taking advantage of the oxidising ability of diaryliodonium is available in the literature. In the present work, a titration method for the determination of diaryliodonium salts is presented. It is based on the reaction of diaryliodonium species with ascorbic acid, whose excess is subsequently determined by means of iodometric potentiometric titration. Application of the protocol to various diaryliodonium salts revealed the scope and limitations of the method.     

Rapid Method for the Micro-Determination of Hydrazine by Amperometric Titration With Potassium Iodate

Abstract

An amperometric method, with potassium iodate as the titrant, for the rapid and precise determination of micro amounts of hydrazine salts is described. Hydrazine dihydrochloride, hydrazine sulfate and hydrazine hydrate could be quantitatively analyzed at the concentration range of 4 × 10^?7 -4×10^?3 M in the presence of 5 M hydrochloric acid. Hydrazine salts, 2×10^?4 -4×10^?3 M, were titrated in 5 minutes with a relative error and a relative standard deviation of 0.1%. It was also found that hydrazine dihydrochloride can be precisely determined, without any interference, even in the presence of hydroxylamine which is ten times as much as the former.

The suitable applied potential between the rotating platinum indicator microelectrode and the silver plate-silver chloride reference electrode was + 0.7V.     

固蓝盐B分光光度法测定药物中抗坏血酸

探讨了一种简便的选择性高的药物中抗坏血酸的测定方法。该方法是基于在酸性介质中抗坏血酸和固蓝盐B的反应,产物的最大吸收为420nm.摩尔吸光系数为1.31×10~4L·mol~(-1)·cm~(-1).方法已应用于某些药物中抗坏血酸的测定,结果与碘量法一致,回收率为98.4％～105％,相对标准偏差低于3.7％。