Determination of lead(II) by argentimetry

A titrimetric method for determination of lead(II), based on the reaction between plumbite and silver ions, is described. Sodium hydroxide solution is added to the sample until the precipitate of lead hydroxide has redissolved. The solution is then made 0.025M in sodium chloride and titrated with silver nitrate. The titration is monitored with a silver electrode. An error smaller than 0.5% has been obtained for 0.05M lead (II).     

Preconcentration of cyanide from water by extraction with tributyltin hydroxide

Samples of water (500 ml) are extracted with 25 ml of 0.25M tributyltin hydroxide in trichloroethylene, which is then stripped with 2M sodium hydroxide, the organic reagent being used for a further extraction of the water sample; this cycle is carried out four times. The combined sodium hydroxide extracts are then titrated with silver nitrate solution, with p-dimethylbenzylidenerhodanine as indicator. Mean recoveries are around 99%, and the limit of determination is 4 microg/l. Thiocyanate, sulphide, methanethiol and complex cyanides do not interfere.     

Analytik der polyacrylnitrilfasern : V über fine abgewandete reduktionsmethode zur bestimmung geringer schwefelmengen in acrylnitrilpolymerisaten

Sulphur contents (0.01–0.2% S) in polyacrylonitriles (50–100 mg samples) can be estimated by decomposition of the polymer by heating with KOH, reduction of the sulphate formed (with acetic acid, hydriodie acid, and hypophosphite) and absorption of hydrogen sulphide in 1 N sodium hydroxide. Sulphide is then determined polarographically utilizing the anodic sulphide wave, or potentiometrically with 0.001 M mercuric chloride as titrant and amalgamated silver wire and stainless steel wire as electrodes. The whole procedure is done easily in a stream of nitrogen and can therefore be applied even when the atmosphere is contaminated with sulphur-containing substances.     

Potentiometric studies on thioacetamide by means of a sulphide ion-selective membrane electrode

The sulphide ion-selective electrode has been found to be applicable to the determination of thioacetamide in the concentration range of 10^-1–10^-3 M by direct potentiometry and titration with silver nitrate. The effects of the acid and alkali content of the solutions on the titration reaction have been studied. In alkaline and slightly acidic solutions the product of the reaction is silver sulphide; in solutions in which the acid concentration exceeds 0.5 M, a precipitate of silver thioacetamide is formed. If the alkali concentration of the solution is lower than that corresponding to the amount of acid formed during the titration, another potential jump occurs before the end-point owing to the decrease of sulphide'concentration governed by hydrolysis.     

Potentiometric studies of dithiooxamide with a sulphide-selective membrane electrode

The sulphide-selective electrode is applicable to the determination of dithiooxamide by titration with silver nitrate. The effect of the alkali content of the solutions on the reaction has been studied. The reaction products are silver sulphide, oxalic acid, and nitric acid. If the alkali concentration of the solution is lower than that equivalent to the acid formed during the titration, the amount of sulphide produced by hydrolysis decreases and the equilibrium potential is established more slowly.The determination is rapid and accurate in the presence of 1 M sodium hydroxide.     

Potentiometric determination of 8-chlorotheophylline

Two methods are described for the potentiometric determination of 8-chlorotheophylline in aqueous solution. Both methods are based on the reaction of 8-chlorotheophylline with silver ions. In the first, the nitric acid produced in the reaction is titrated with sodium hydroxide. In the second, the 8-chlorotheophylline is titrated directly with silver nitrate in sodium carbonate medium. Both methods give reasonably accurate and reproducible results, and are suitable for the assay of 8-chlorotheophylline in pharmaceutical preparations.     

Voltammetric,potentiometric and amperometric studies with a rotated aluminum wire electrode : Amperometric titration of fluoride with aluminum

The rotated aluminum electrode is a suitable indicator electrode in the amperometric titration of fluoride, Fluoride in concentrations varying between 1.10^-4 and 2.10^-3M was titrated with a standard aluminum nitrate solution in aqueous buffer solutions (pH between 3.6 and 46) Equilibrium was established within 15 mim. The fluoride-aluminum ratio at the (true) end-point was found to increase from 2 2 in 10^-4M fluoride to 28 in. 2.10^-3M fluoride. The titration calculated from the stability constants of the various aluminum-fluoride complexes were found to be in excellent agreement with the experimental curves.From a practical point of view titration in an acetate buffer in 50% alcohol in the presence of 0 5 M potassium or sodium nitrate is recommended. The fluoride-aluminum ratio at the end-point was found to be 5 9 ± 0 1 and independent of the fluoride concentration.     

Polarography of some sulphur-containing compounds : Part XII. Anodic waves of monoalkyldithiocarbamates and their reactions with heavy metals

Monoalkyldithiocarbamates give two anodic polarographic waves, corresponding to a one-electron and a two-electron process. A reaction scheme is proposed. The unusual behaviour observed during controlled-potential electrolysis in sodiumhydroxide media is interpreted as a chemical reaction of the primary electrolysis product; the species formed gives a wave similar to the original compound. Different adsorption phenomena are probably caused by varying orientation of the mercury compound on the electrode surface. The adsorbed layer formed in sodium hydroxide solution is so close-packed that it prevents hydroxyl ions from penetrating and thus giving an anodic wave. For analytical purposes, 0.1 M sodium hydroxide is the most suitable supporting electrolyte; linear calibration graphs can be obtained over the range 5 · 10^-5–1 · 10^-3M.     

Potentiometric determination of tetraphenylborate with silver nitrate

A simple potentiometric method for determining the tctraphenylborate ion (C₆H₅)₄B- contents of organic amine tetraphcnylborate salts has been developed. The compounds arc dissolved in 1 : 1 aqueous acetone; and the solution is buffered at a pH of 5 with 3M acetic acid and 3M sodium acetate. The resulting solution is then titrated with 0.06N aqueous silver nitrate, using a silver indicating electrode, a glass reference electrode and a Beckman pH meter to indicate EMF changes. Platinum electrodes in conjunction with the Malmstadt automatic titrator can also be used. Good end-points were obtained for all structure types except the primary aromatic amine borates. Values for (C₆H₅)₄B- found were within 2% of theory for 22 compounds so analyzed.     

Coulometric generation of molybdenum(v)

Molybdenum (V) was generated at a platinum cathode from 0.7 M molybdenum(VI) in 4 M sulfuric acid. A current efficiency of 99.9% was attained. A limiting current density of 0.05 mA/cm²/mM was found. The formal potential of the Mo(VI)–Mo(V) couple in 4 M sulfuric acid was determined to be ca. 0.55 V vs. N.H.E. Chromium(VI) solutions were titrated over a wide range of sample size and generating current. Amperometric titration curves were interpreted from current-voltage curves. Titrations could be performed in the presence of oxygen at the 1μeq. level. The effect of nitrate, perchlorate, orthophosphate, and chloride ions on the titration was determined.     

Coulometric argentometric determination of microamounts of sulphur in iron and steel after reduction to hydrogen sulphide with iron(II) in strong phosphoric acid medium

A coulometric method was developed for the determination of microamounts of sulphur in iron and steel. Hydrogen sulphide is quantitatively evolved by reduction with iron(II) in strong phosphoric acid medium and is titrated with electrolytically generated silver ion from a silver anode. Microamounts of sulphide (2.96–224.3 μg) in sodium sulphide standard solutions could be determined with an error of only a few percent. Sulphur in a potassium sulphate standard solution is quantitatively reduced to hydrogen sulphide and could be separated from the solution by heating and determined accurately. Trace amounts of sulphur (7–100 μg g^?1) in iron and steels could be determined with a standard deviation of 0.7–2.1 μg g^?1.     

Neue Bestimmungsmethode für organisch gebundenes Jod,Brom und Chlor

The catalytic dehalogenation with sodium tetrahydroborate enables rapid and simple halogen determinations especially in solutions, for example of X-ray contrasters. Organic bound iodine (in water, resp. dimethylformamide) is splitted off by NaBH₄ in the presence of palladium under stirring within 15 min at room temperature. More stable bromine and chlorine compounds need 10 min boiling of the reaction mixture with palladium on charcoal. After decomposition of the excessive sodium tetrahydroborate with acetone and addition of sulphuric acid, the halide ions are titrated potentiometrically in the known manner with silver nitrate solution using a silver/silver chloride electrode. Poisoning of the catalyst and volatility of the sample are possible disturbances.     

Polarography of some sulphur-containing compounds : Part XII.Anodic waves of dialkyldithiocarbamates

Dialkyldithiocarbamates give only a one-electron anodic wave. The various adsorption phenomena are probably caused by varying orientation of the mercury compounds on the electrode surface; the irregular i-t curves recorded at —0.04 V and the anomalous behaviour of the anodic current between +0.2 V and —0.4 V can be interpreted as the behaviour of an adsorbed film at the electrode. Analytical measurements are best made in 60% ethanolic 0.1 M sodium hydroxide media at concentrations of about 10^-5 M dialkyldithiocarbamate; a method is given for the analysis of the monoalkyl and dialkyl compounds in mixtures.     

Gaseous catalysts for end-point indication in titrimetric analysis in the microgram range

The method of end-point detection described is very sensitive. In titrations with sodium sulphide, the first drop of titrant in excess cause evolution of hydrogen sulphide which acts as a catalyst for the indicating iodine—azide reaction. The gas formed at the end-point is transferred by a nitrogen stream to the indicator vessel. Microgram amounts of metal ions (Sb, Ni, Fe, Hg⁺ Cd, Pb⁺ Cu, Ag⁺ Cu) and permanganate can be titrated in acidic solution with standard sulphide solution. In a variation of this method, acid-base titrations are possible.     

Development of oxopyrrolidine-based anti-cancer compounds: DNA binding, in silico, cell line studies, drug-likeness and mechanism at supra-molecular level

Due to an increasing demand for effective anti-cancer drugs, an oxopyrrolidine-based ligand, sodium 1-(3-(2-aminoethylamino)propyl)-5-oxopyrrolidine-2-carboxylate, was synthesised by the sodium hydride-assisted coupling of pyroglutamic acid with 1,3-diiodopropane under a nitrogen atmosphere. The intermediate thus formed was allowed to react with ethylenediamine in acetonitrile. The ligand formed individual complexes with Cu(II) and Ni(II) metal ions, respectively. The complexes were relatively resistant to degradation in PBS at physiological pH. The DNA-binding constants (K _b) for the ligand, copper and nickel complexes were 2.09 × 104 M^-1, 2.37 × 104 M^-1 and 2.11 × 104 M^-1, respectively, revealing the strong binding of these complexes with DNA. Haemolysis assays indicated that the ligand and its complexes were less toxic to rabbit RBCs than doxorubicin. Lipinski’s parameters calculated for the reported compounds indicated their good oral bioavailability. All the compounds exhibited good activities towards MCF-7 (wild type) cancer cell lines. The results of in silico studies, DNA-binding and anti-cancer activities indicated that the reported compounds might be interacting with DNA as one of their possible mechanisms of action.     

(Perhalogenmethylthio)heterocyclen. XXI. Reaktionen halogenierter perhalogenmethylthiopyrrole: Salz- und radikalbildung,dimerisierung

2-Chloro-3,4,5-tris(trifluoromethylthio)pyrrole ( 2a ), 3-Chloro-2,4,5-tris(trifluoromethylthio)pyarrole ( 2b ) and 3,4-dichloro-2,5-bis(trifluromoethylthio)pyrrole ( 2c ) react with silver nitrate/silver acetate in good yield to give the corresponding N-silver salts 3a-c . Compound 2b forms with an aqueous potassium hydroxide solution the N-potassium salt 4 . Compounds 3a and 3b react with iodine to give the dimeers 2,2′-dichloro-3,3,′ 4,4′5,5′-hexakis(trifluoromethylthio)-2,2′-bi-2H-pyrrolyl ( 5a ) and 3,3′-dichloro-2,2′,4,4′,5,5′-hexakis(trifluoromethylthio)-2,2′-bi-2H-pyrrolyl ( 5b ). The dimers dissociate in solution to the corresponding pyrrolayl radicals. The esr and endor spectra of 3-chloro-2,4,5-tris(trifluoromethylthio)pyrrolyl were measured; coupling constants are given. For the newly prepared substances melting-points, ¹⁹F-nmr and ir spectroscopical data are provided.     

Amperometric determination of organic isothiocyanates

An amperometric titration method is described for the determination of 1-5 mg of organic isothiocyanates, based on their quantitative reaction with n-butylamine in dimethylfonnamide to form N,N-disubstituted thioureas which are then titrated amperometrically in aqueous ammonia-ammonium nitrate buffer with silver nitrate (dropping mercury electrode at -0.56V). The end-point corresponds to a silver:thiourea ratio of 2:1, with precipitation of silver sulphide. The method is simple, accurate, widely applicable, and gives reproducible results.     

Ion-selective carbon-paste electrodes for halides and silver(I) ions

The behaviour of a simple type of ion-selective electrode for halogens and silver has been studied. The electrode consists of a plastic body filled with carbon paste, the surface of which can be easily renewed. The paste composition is based on carbon-nujol (5:1, w/v) or carbon-paraffin wax (3:1,w/w) containing a prepared mixture of silver halide-silver sulphide (1–30%). The electrodes have low ohmic resistance and show a rapid Nernstian response (within 2–5 mV) for halide and silver ions down to 5·10^-5M chloride, 1·10^-5M bromide and 5·10^-7M iodide with the respective electrodes. Ions forming very stable complexes with halide or silver and those having strong oxidizing or reducing action interfere.     

Reaction of 3-aminoquinoline-2,4-diones with isothiocyanic acid—an easy pathway to thioxo derivatives of imidazo[1,5-c]quinazolin-5-ones and imidazo[4,5-c]quinolin-4-ones

3-Amino-1H,3H-quinoline-2,4-diones react with thiourea or potassium thiocyanate in boiling acetic acid to give novel 2,3-dihydro-3-thioxoimidazo[1,5-c]quinazolin-5(6H)-ones in high yields. However, if the starting compounds are substituted with a benzyl group at position 3, a C-debenzylation proceeds to give 2,3-dihydro-2-thioxo-1H-imidazo[4,5-c]quinolin-4(5H)-ones. According to a proposed reaction mechanism, a molecular rearrangement of the primarily formed mono-substituted thiourea takes place. All compounds were characterized by ¹H, ¹³C and ¹⁵N NMR and IR spectroscopy as well as by mass spectrometry.     

Trace fluoride determination with specific ion electrode

A method is described for determining 10^-5–10^-4M fluoride in a variety of solutions potentiometrically with a fluoridc-specific electrode, by a standard addition method. Any change of ionic strength or the nature of the solution that might alter activity coefficients or junction potentials is minimized. The relationship between potential and fluoride concentration thus follows the Nernst equation, and the unknown concentration can be calculated. Experimental data are given for solutions of sodium choride, sodium nitrate, acidified sodium silicate and sodium hydroxide, lithium chloride, and phosphoric acid. Metal ions (e.g., Al³⁺, UO₂²⁺, Fe³⁺, Th⁴⁺) that interfere by forming complexes with fluoride can be precomplexed with phosphoric acid. The relative error is estimated at 10%, and the relative standard deviation is less than 5% over the concentration range 10^-5–10^-4M fluoride.