首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 46 毫秒
1.
For over two decades, the high-temperature phase transition (HTPT) at around T p = 180 °C on KH2PO4 (KDP), which involves an ionic conductivity increase, constitutes a controversial subject; while most authors ratify a physical transformation (tetragonal → monoclinic phase transition), others defend the chemical transformation. A careful high-temperature phase behavior examination of this acid salt by means of modulated and conventional differential scanning calorimetry, thermogravimetric analysis, simultaneous thermogravimetric and differential scanning calorimetry, impedance spectroscopy, and temperature evolution of X-ray diffraction was performed to provide a possible solution to this long-standing issue. We found that the structural phase transition does not take place. Instead, a chemical transformation occurs at T p. When KDP is heated through this temperature, the sample initially corresponding to a single phase (tetragonal) transforms to a sample composed of two solid phases: tetragonal KDP, located at its bulk, and monoclinic potassium metaphosphate (KPO3), located at its surface. Most of the water produced evaporates, but a small portion of liquid water bonds to KPO3. Because this is of polymeric nature, it takes the role of a host matrix that contains liquid water regions. Consequently, given that part of the water dissolves a portion of surface salt (providing protons), the surface sample system behaves in a similar manner to a polymer electrolyte membrane where the proton transport mechanism includes the vehicle type, using hydronium (H3O+) as a charge carrier. On further heating, the bulk tetragonal KDP phase reduced to its total decomposition. The metastability of the high-temperature phase below T p is also explained.  相似文献   

2.
N. Nouiri  K. Jaouadi  T. Mhiri  N. Zouari 《Ionics》2016,22(9):1611-1623
Synthesis and structural characterization by single-crystal X-ray diffraction method, thermal behavior, and electrical proprieties are given for a new compound with a superprotonic phase transition Cs2(HSO4)(H2AsO4). The title compound crystallizes in the monoclinic system with the P21/n space group. The structure contains zigzag chains of hydrogen-bonded anion tetrahedra that extend in the [010] direction. Each tetrahedron is additionally linked to a tetrahedron neighboring chain to give a planar structure with hydrogen-bonded sheets lying parallel to (10ī). The existence of O–H and (S/As)–O bonds in the structure at room temperature has been confirmed by IR and Raman spectroscopy in the frequency ranges 4000–400 cm?1and 1200–50 cm?1, respectively. Differential scanning calorimetry analysis of the superprotonic transition in Cs2(HSO4)(H2AsO4) showed that the transformation to high temperature phase occurs at 417 K by one-step process. Thermal decomposition of the product takes place at much higher temperatures, with an onset of approximately 534 K. The superprotonic transition was also studied by impedance and modulus spectroscopy techniques. The conductivity in the high temperature phase at 423 K is 1.58 × 10?4 Ω?1 cm?1, and the activation energy for the proton transport is 0.28 eV. The conductivity relaxation parameters associated with the high disorder protonic conduction have been examined from analysis of the M”/M”max spectrum measured in a wide temperature range. Transport properties of this material appear to be due to the proton hopping mechanism.  相似文献   

3.
The Na superionic conductor (NASICON) NaNbAlP3O12 compound was prepared by the conventional solid-state reaction method. The formation of single-phase material was confirmed by X-ray diffraction studies, and it was found to be a hexagonal phase at room temperature. The electrical conductivity was measured in the frequency range from 200 Hz to 5 MHz and temperatures between 573 and 773 K using impedance spectroscopy technique. The obtained results were analyzed by fitting the experimental data to the equivalent circuit model. The analysis of Nyquist plots has revealed the contribution of three electrically active regions corresponding to the bulk mechanism, distribution of grain boundaries, and electrode processes. Besides, the frequency dependence of the conductivity is interpreted in terms of Jonscher’s law. Temperature dependence of the power law exponent s strongly suggests that the non-overlapping small polaron tunneling (NSPT) model is the dominant transport process. The variation of the imaginary part of the complex modulus as a function of angular frequency at several temperatures shows a double relaxation peak suggesting the presence of grains and grain boundaries in the sample. An analysis of the dielectric constants ε″ and loss tangent tan (δ) with frequency shows a distribution of relaxation times.  相似文献   

4.
A Li0.5FeV1.5O4 sample was synthesized using sol-gel route. The X-ray diffraction study indicates formation of spinel phase (with Fd3m space group) for this sample. LiO4, LiO6, and V-O bonds were identified from the Raman spectrum, while LiO4 and Fe-O bonds were identified from the FTIR spectrum of this sample phase. The FESEM study indicates formation of inhomogeneous grains. The surface area of 74.39 m2/g was estimated from the Brunauer-Emmett-Teller (BET) surface area analysis technique. The cyclic voltammetry study of Li0.5FeV1.5O4 indicates an anodic peak at 2.1 V while a cathodic peak at 1.98 V. The charge-discharge study exhibits two voltage plateaus respectively at 2.1 and at 4 V. Stable electrochemical capacity of 40 mAh/g for Li0.5FeV1.5O4 was found for 30 cycles. The electrochemical impedance spectroscopy study indicates smaller bulk resistance and higher ionic diffusion, i.e., less Warburg impedance for this phase. An energy density of 89 Wh/kg, a power density of 33 W/kg, and a 90% Coulombic efficiency was achieved with relatively good cyclic stability from Li0.5FeV1.5O4.  相似文献   

5.
Lithium pyrophosphate compound Li2CuP2O7 has been synthesized through solid state reaction method. FTIR and XRD results, realized at room temperature, indicate respectively the dominant feature of pyrophosphate anion (P2O7)4? and a pure monoclinic phase with I2/a space group. Electrical and dielectric properties have been studied using impedance spectroscopy complex over a wide temperature (576–710 K) and frequency (209 Hz–1 MHz) range. From the direct and alternative conductivities (DC and AC), electrical conduction is found to be thermally activated process. The frequency-dependent AC conductivity obeys Jonscher’s universal power law σAC~Aωs. The differential scanning calorimetry spectrum discloses phase transition at 622 K.  相似文献   

6.
The phase composition and the temperature dependence of the magnetization of the Er0.45Ho0.55Fe2 compound in coarse-grained, microcrystalline, and submicrocrystalline states are investigated experimentally. It is found that, upon heating under vacuum, the Er0.45Ho0.55Fe2 microcrystalline powder with a crystalline grain size of ∼1 μm undergoes decomposition into pure iron and rare-earth (erbium and holmium) oxides and nitrides at a temperature of 500 K. The changes observed in the phase composition of the microcrystalline powder due to annealing are confirmed by x-ray diffraction analysis. Heating of the Er0.45Ho0.55Fe2 submicrocrystalline sample leads to a partial change in the phase composition. The phase composition of a large crystal (∼1 mm in size) remains unchanged upon heating to 1080 K. It is shown that the thermal stability of the Er0.45Ho0.55Fe2 compound depends on the crystalline grain size. __________ Translated from Fizika Tverdogo Tela, Vol. 44, No. 6, 2002, pp. 1060–1063. Original Russian Text Copyright ? 2002 by Mulyukov, Sharipov, Korznikova.  相似文献   

7.
Vinyl ethylene carbonate (VEC) is investigated as an electrolyte additive to improve the electrochemical performance of LiNi0.4Mn0.4Co0.2O2/graphite lithium-ion battery at higher voltage operation (3.0–4.5 V) than the conventional voltage (3.0–4.25 V). In the voltage range of 3.0–4.5 V, it is shown that the performances of the cells with VEC-containing electrolyte are greatly improved than the cells without additive. With 2.0 wt.% VEC addition in the electrolyte, the capacity retention of the cell is increased from 62.5 to 74.5 % after 300 cycles. The effects of VEC on the cell performance are investigated by cyclic voltammetry(CV), electrochemical impedance spectroscopy(EIS), x-ray powder diffraction (XRD), energy dispersive x-ray spectrometry (EDS), scanning electron microscopy (SEM), and attenuated total reflectance-Fourier transform infrared (ATR-FTIR). The results show that the films electrochemically formed on both anode and cathode, derived from the in situ decomposition of VEC at the initial charge–discharge cycles, are the main reasons for the improved cell performance.  相似文献   

8.
The Li3V2(PO4)3/C (LVP/C) cathode materials for lithium-ion batteries were synthesized via ethylene glycol-assisted solvothermal method. The phase composition, phase transition temperature, morphology, and fined microstructure were studied using X-ray diffraction (XRD), differential thermal analyzer (DTA), scanning electron microscope (SEM), and transmission electron microscope (TEM), respectively. The electrochemical properties, impedance, and electrical conductivity of LVP/C cathode materials were tested by channel battery analyzer, the electrochemical workstation, and the Hall test system, respectively. The results shown that the appropriate amount of water added to ethylene glycol solvent contributes to the synthesis of pure phase LVP. The LVP10/C cathode material can exhibit discharge capacities of 128, 126, 126, 123, 124, and 114 mAh g?1 at 0.1, 0.5, 2, 5, 10, and 20 C in the voltage range of 3.0–4.3 V, respectively. Meanwhile, it shows also a stable cycling performance with the capacity retention of 89.6% after 180 cycles at 20 C.  相似文献   

9.
In this investigation, Mn3O4 spinel-type oxide was synthesized at low temperature using the Pechini process. We employed a sol-gel route, in which a solution of Mn(II) in a mixture of citric acid and ethylene glycol was heated to form a polymeric precursor, followed by annealing at lower temperature. The oxide obtained was identified by X-ray diffraction, scanning electron spectroscopy, and Raman spectroscopy. The results revealed that the formation of Mn3O4 hausmannite structure with a minor secondary phase of MnSO4 occurred at or above 280 °C. The sample powder consisted of fine grains with homogeneous morphology and an average size close to 1 μm was obtained. This new preparation procedure yielded an electrode oxide which appears to be a promising cathode material for fuel cells and metal-air batteries.  相似文献   

10.
Li1,3Ti0,7Al0,3(PO4)3 (LATP) powder was obtained by a conventional melt-quenching method and consolidated by field-assisted sintering technology (FAST) at different temperatures. Using this technique, the samples could be sintered to relative densities in the range of 93 to 99 % depending on the sintering conditions. Ionic and thermal conductivity were measured and the results are discussed under consideration of XRD and SEM analyses. Thermal conductivity values of 2 W/mK and ionic conductivities of 4?×?10?4 Scm?1 at room temperature were obtained using relatively large particles and a sintering temperature of 1000 °C at an applied uniaxial pressure of 50 MPa.  相似文献   

11.
A comparison of electrochemical performance between LiFe0.4Mn0.595Cr0.005PO4/C and LiMnPO4/C cathode materials was conducted in this paper. The cathode samples were synthesized by a nano-milling-assisted solid-state process using caramel as carbon sources. The prepared samples were investigated by XRD, SEM, TEM, energy-dispersive X-ray spectroscopy (EDAX), powder conductivity test (PCT), carbon-sulfur analysis, electrochemical impedance spectroscopy (EIS), and galvanostatic charge-discharge cycling. The results showed that LiFe0.4Mn0.595Cr0.005PO4/C exhibited high specific capacity and high energy density. The initial discharge capacity of LiFe0.4Mn0.595Cr0.005PO4/C was 163.6 mAh g?1 at 0.1C (1C = 160 mA g?1), compared to 112.3 mAh g?1 for LiMnPO4/C. Moreover, the Fe/Cr-substituted sample showed good cycle stability and rate performance. The capacity retention of LiFe0.4Mn0.595Cr0.005PO4/C was 98.84 % over 100 charge-discharge cycles, while it was only 86.64 % for the pristine LiMnPO4/C. These results indicated that Fe/Cr substitution enhanced the electronic conductivity for the prepared sample and facilitated the Li+ diffusion in the structure. Furthermore, LiFe0.4Mn0.595Cr0.005PO4/C composite presented high energy density (606 Wh kg?1) and high power density (574 W kg?1), thus suggested great potential application in lithium ion batteries (LIBs).  相似文献   

12.
Epitaxial BaFe1.8Cr0.2As2 thin films with the tetragonal c-axis perpendicular to the thin film surface were grown on (LaAlO3)0.3(Sr2AlTaO6)0.7 (LSAT) single crystalline substrates using pulsed laser deposition (PLD). Resistive measurements indicate the existence of two transitions at temperatures of about 80 K and 40 K. The transition at 80 K is attributed to the structural transition from the high temperature tetragonal phase to the low temperature orthorhombic phase accompanied with the magnetic transition from a paramagnetic to an antiferromagnetic state as known for doped bulk systems. Below T ≈ 40 K the magnetization curves measured perpendicularly to the orthorhombic c-axis in fields up to 9 Tesla show two inflexion points indicating metamagnetic transitions.  相似文献   

13.
N. Nouiri  K. Jaouadi  N. Zouari  T. Mhiri 《Ionics》2017,23(6):1461-1470
The Rb3(HSeO4)2.5(H2PO4)0.5 compound was prepared and its thermal behavior and electric properties were investigated. The thermogravimetry (TGA) analysis and the differential scanning calorimetric (DSC) show the presence of a structural phase transition of the title compounds at 374 K which is confirmed by the variation of fp and σdc as a function of temperature. The complex impedance of the Rb3(HSeO4)2.5(H2PO4)0.5 compound has been investigated in the temperature range of 295–453 K and in the frequency range 209 Hz–1 MHz. The impedance plots show semicircle arcs at different temperatures, and an electrical equivalent circuit has been proposed to explain the impedance results. The circuits consist of the parallel combination of bulk resistance Rp and constant phase elements CPE1 in series with fractal capacity CPE2. The frequency dependence of the conductivity is interpreted in terms of Jonscher’s law. The conductivity dc follows the Arrhenius relation. The near value of activation energies obtained from the analysis of modulus, conductivity data, and circuit equivalent confirm that the transport is through the ion hopping mechanism, dominated by the motion of the H+ proton in the structure of the investigated materials.  相似文献   

14.
The lithium dihydrogen phosphate LiH2PO4 has been investigated by X-ray powder diffraction, scanning electron microscopy (SEM), and electrical impedance spectroscopy. The Rietveld refinements based on the XRD patterns show that the compound is crystallized in the orthorhombic system with Pna21 space group, and the refined unit cell parameters are a = 6.2428 Å, b = 7.6445 Å, and c = 6.873 Å. The electrical properties were studied using complex impedance spectroscopy as a function of frequency (104–107 Hz) at various temperatures (300–400 K). The Nyquist plots are well fitted to an equivalent circuit consisting of a series of combination of grains and inhomogeneous electrode surface effect. The frequency dependence of the conductivity is interpreted in terms of Jonscher’s law. Moreover, the near value of the activation energies obtained from the equivalent circuit and analysis of M″ confirms that the transport is through ion hopping mechanism dominated by the motion of the proton in the structure of the investigated material.  相似文献   

15.
Guoqiang Liu  Lei Wen  Yue Li  Yulong Kou 《Ionics》2015,21(4):1011-1016
The pure phase P2-Na2/3Ni1/3Mn2/3O2 was synthesized by a solid reaction process. The optimum calcination temperature was 850 °C. The as-prepared product delivered a capacity of 158 mAh g?1 in the voltage range of 2–4.5 V, and there was a phase transition from P2 to O2 at about 4.2 V in the charge process. The P2 phase exhibited excellent intercalation behavior of Na ions. The reversible capacity is about 88.5 mAh g?1 at 0.1 C in the voltage range of 2–4 V at room temperature. At an elevated temperature of 55 °C, it could remain as an excellent capacity retention at low current rates. The P2-Na2/3Ni1/3Mn2/3O2 is a potential cathode material for sodium-ion batteries.  相似文献   

16.
Thermal decomposition of (NH4)2ZrF6 resulting in ZrO2 formation within the temperature range of 20°–750°С has been investigated by means of thermal and X-ray diffraction analysis and IR and Raman spectroscopy. It has been established that thermolysis proceeds in six stages. The vibrational-spectroscopy data for the intermediate products of thermal decomposition have been obtained, systematized, and summarized.  相似文献   

17.
In order to study the influence of powder calcination temperature on lithium ion conductivity, synthesized Li1.3Ti1.7Al0.3(PO4)3 (LATP) was calcined at temperatures between 750 and 900 °C. The shape and size of the particles were characterized employing scanning electron microscopy (SEM), and specific surface area of the obtained powder was measured. The crystallinity grade of different heat-treated powders was calculated from XRD spectra. Posteriorly, all powders were sintered at 1100 °C employing field-assisted sintering (SPS), and the electrical properties were correlated to the calcination conditions. The highest ionic conductivity was observed for samples made out of powders calcined at 900 °C.  相似文献   

18.
Polycrystalline samples of Ba4SrRTi3V7O30 (R=Sm and Dy), members of the tungsten-bronze family, were prepared using a high-temperature, solid-state reaction technique and studied their electrical properties (using complex impedance spectroscopy) in a wide range of temperature (31–500°C) and frequency (1 kHz-1 MHz). Preliminary structural (XRD) analyses of these compounds show the formation of single-phase, orthorhombic structures at room temperature. The scanning electron micrographs (SEM) provided information on the quality of the samples and uniform distribution of grains over the entire surface of the samples. Detailed studies of the dielectric properties suggest that they have undergone ferroelectric-paraelectric phase transition well above the room temperatures (i.e., 432 and 355°C for R= Sm and Dy, respectively, at frequency 100 kHz). Measurements of electrical conductivity (ac and dc) as a function of temperature suggest that the compounds have semiconducting properties much above the room temperature, with negative temperature coefficient of resistance (NTCR) behavior. The existence of ferroelectricity in these compounds was confirmed from a polarization study.   相似文献   

19.
LiSn2P3O12 with sodium (Na) super ionic conductor (NASICON)-type rhombohedral structure was successfully obtained at low sintering temperature, 600 °C via citric acid-assisted sol-gel method. However, when the sintering temperature increased to 650 °C, triclinic structure coexisted with the rhombohedral structure as confirmed by X-ray diffraction analysis. Conductivity–temperature dependence of all samples were studied using impedance spectroscopy in the temperature range 30 to 500 °C, and bulk, grain boundary and total conductivity increased as the temperature increased. The highest bulk conductivity found was 3.64?×?10?5 S/cm at 500 °C for LiSn2P3O12 sample sintered at 650 °C, and the lowest bulk activation energy at low temperature was 0.008 eV, showing that sintering temperature affect the conductivity value. The voltage stability window for LiSn2P3O12 sample sintered at 600 °C at ambient temperature was up to 4.4 V. These results indicated the suitability of the LiSn2P3O12 to be exploiting further for potential applications as solid electrolytes in electrochemical devices.  相似文献   

20.
Lead-free Na0.5Bi0.5TiO3 (NBT) and (1 ? x)Na0.5Bi0.5TiO3 + xBaTiO3 with x = 0.1 and 0.2 (where x = 0.1 and 0.2 are named as NBT1 and NBT2, respectively), (1 ? y)Na0.5Bi0.5TiO3 + yBa0.925Nd0.05TiO3 with y = 0.1 and 0.2 (where y = 0.1 and 0.2 are named as NBT3 and NBT4, respectively)-based relaxor ferroelectric ceramics were prepared using the sol-gel method. The crystal structure was investigated by X-ray diffraction (XRD) at room temperature (RT). The XRD patterns confirmed the presence of the rhombohedral phase in all the samples. The electrical properties of the present NBT-based samples were investigated by complex impedance and the modulus spectroscopy technique in the temperature range of RT–600 °C. The AC conductivity was found to increase with the substitution of Ba2+ ions to the NBT sample whereas it significantly decreased with the addition of Nd3+ ions. The more anion vacancies in Ba-added samples and the lower anion vacancies in Nd-added samples were found to be responsible for higher and lower conductivities, respectively.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号