Resistivity and thermoelectric power of Bi2Sr2Ca−xPrxCu2Oy system

Samples of Bi₂Sr₂Ca_1−xPr_xCu₂O_y have been characterized by resistivity and thermoelectric power measurements. All metallic samples show superconductivity with a maximum T_c = 90 K at X = 0.2. The sample of x = 0.6 shows a crossover from hopping conduction at low temperature above T_c to metallic conduction at high temperature. For the metallic samples below x = 0.6, the results of thermoelectric power are well fitted by both of a phenomenological band spectrum model and the Nagaosa and Lee model.     

Characterization of nonstoichiometric nickel manganite spinels NixMn3−x□3δ/4O4+δ by temperature programmed reduction

Cation deficient spinels Ni_xMn_3−x□_3δ/4O_4+δ (0≤x≤1) have been prepared by thermal decomposition of mixed oxalates Ni_x/3Mn_(3−x)/3(C₂O₄)·nH₂O in air at 623 K. They have been characterised by temperature programmed reduction (TPR) under H₂, the reaction being followed by gravimetric and powder X-ray diffraction measurements. It has been shown that TPR proceeds in several steps. The first steps correspond to the loss of nonstoichiometric oxygen leading to the formation of a stoichiometric oxide. During the following stages the manganese cations are reduced, causing the spinel structure to be destroyed, and the formation of solid solution of NiO in a cubic MnO. Subsequently, Ni²⁺ cations undergo a reduction to metallic nickel, and, finally, a mixture of nonstoichiometric MnO_1−δ and metallic nickel is formed. These oxides contain a high level of vacancies which vary with the nickel content with a maximum of δ≈1 near x=0.6. This nonstoichiometry is ascribed both to the presence of Ni³⁺ and excess of Mn⁴⁺.     

An examination of the initial oxidation of a uranium-base alloy (U–14.1 at.% Nb) by O2 and D2O using surface-sensitive techniques

The corrosion resistance of uranium is greatly enhanced by alloying with niobium. In this study the initial stages of corrosion of a specific uranium-base alloy (U–14.1 at.% Nb) by O₂ or D₂O have been examined using the surface specific techniques of X-ray photoelectron spectroscopy (XPS), thermal programmed desorption (TPD), static secondary-ion mass spectroscopy (SSIMS), and sputtered neutrals mass spectroscopy (SNMS). XPS studies of the U–14.1 at.% Nb surface following oxidation using O₂ at 300 K indicate production of a thin oxide overlayer of stoichiometric UO_2.0 intermixed with Nb₂O₅. The same stoichiometry is exhibited for uranium when the oxide is prepared at 500 K with O₂; although, niobium is much less oxidized exhibiting a mixture of NbO and Nb. Contrary to previous XPS literature, SNMS depth profiling studies reveal that oxidation by O₂ is much greater (as judged by oxide layer thickness) than that exhibited by D₂O. An oxide layer thickness of less than 20 Å was created using D₂O as an oxidant at 300 K with exposures >3500 L (oxide layers created from O₂ are significantly greater at much smaller exposures). Formation of a critical density of Nb₂O₅ is suggested to be responsible for the enhanced corrosion resistance by preventing diffusion of O⁻ (O²⁻) or OD⁻/OH⁻ into the oxide/metal interface region. The domains of stability of hydroxyl formation have also been followed using TPD, SSIMS and XPS. Maximal surface hydroxyl concentrations (Θ_rel=0.30) are obtained at a surface temperature of 175 K for these experimental conditions.     

Transport properties of SrCe0.95Y0.05O3−δ and its application for hydrogen separation

Transport properties of SrCe_0.95Y_0.05O_3−δ were studied by impedance spectroscopy and by measuring open-cell voltage (OCV) and gas permeation. Ionic transference numbers were determined by measuring the OCV of concentration cells and water vapor evolution of an O₂/H₂ fuel cell. We observed interfacial polarization on the basis of the I–V curves obtained by discharging a hydrogen concentration cell or an O₂/H₂ fuel cell. The observed high protonic conductivity (high proton and low oxide ion transference numbers) makes SrCe_0.95Y_0.05O_3−δ a potential material for hydrogen separation. From proton conductivity measurements, under a given hydrogen partial pressure difference of 4%/0.488%, the hydrogen permeation rate (of a dense membrane with 0.11 cm in thickness) was calculated to be ≈0.072 cm³ (STP) cm⁻² min⁻¹ at 800°C, whereas the permeation rate calculated from short-circuit current measurements was ≈0.023 cm³ (STP) cm⁻² min⁻¹ at 800°C. The difference between calculated and observed permeation rates is probably due to interfacial polarization.     

氩、氢混合等离子体处理对GaAs表面性质及发光特性的影响

介绍了一种氩、氢混合等离子体清洗GaAs基片的实验工艺,深入研究了氩、氢等离子体清洗GaAs表面污染物和氧化层,并活化表面性能的基本原理,同时讨论了气体流量、溅射功率和清洗时间等不同溅射参数对等离子体清洗效果的影响。结果表明,在氩气和氢气流量分别为10 cm³/min和30 cm³/min,溅射功率为20 W,清洗时间为15 min的条件下,GaAs样品的光致发光强度提高达139.12%,样品表面的As-O键和Ga-O键基本消失。     

XPS investigation of preferential sputtering of S from MoS2 and determination of MoSx stoichiometry from Mo and S peak positions

The preferential sputtering of S from bulk MoS₂ standard samples exposed to 3 keV Ar⁺ ion bombardment has been studied by XPS. The MoS_x stoichiometry decreases from MoS₂ to MoS_1.12 with a concomitant reduction in the Mo 3d_5/2 binding energy from 229.25 to 228.35 eV. The altered layer extends to a depth of 3.8 nm and is proposed to consist of a single amorphous MoS_x phase in which Mo has a varying number of nearest neighbour S atoms. Using peak positions alone it is possible to determine the MoS_x stoichiometry to an accuracy of x±0.1 from a plot of MoS_x stoichiometry against (Mo 3d_5/2–S 2p_3/2) binding energy. The results are of strong current interest for coating analysis applications as MoS₂ is a compound capable of providing low friction properties when incorporated into hard coatings.     

Investigation of the Li1+xV3O8 electrode–organic electrolyte interface by scanning photoelectron microscopy

To investigate the formation of a solid electrolyte interface (SEI) on the Li_1+xV₃O₈ electrode surface in the thermodynamic stability range of the organic electrolyte, we applied scanning photoelectron microscopy (SPEM) to a pristine electrode and to an electrode after ten cycles. The F K-edge absorption spectrum of the cycled electrode showed that LiF forms on the electrode surface during the lithium insertion–extraction process in the Li_1+xV₃O₈/Li cell. The photoelectron spectrum for the cycled electrode showed intense spectral features corresponding to Li 1s, F 2s, F 2p, and P 2p electron signals, whereas these spectral features were of negligible intensity for the pristine electrode. The above results give strong support for the formation of an SEI that consists of LiF and compounds containing phosphorus during operation of the battery. The SPEM images also revealed that the fluorine distribution on the surface of the cycled electrode was inhomogeneous.     

Structure and properties of Bi2Sr2CaCu2Ox/Bi2Sr2CuOx superlattices prepared by RF magnetron sputtering

We have prepared Bi₂Sr₂CaCu₂O_x/Bi₂Sr₂CuO_x (2212/2201) superlattices with various stacking periodicity by multitarget RF magnetron sputtering. Their crystal structure and electrical properties were investigated. The superlattice was found to be successfully constructed from the data of XRD patterns, AES, etc. The critical temperature increased almost linearly with increasing thickness of the 2212 phase up to a thickness of 6 unit cells. On the other hand, it did not decrease as the thickness of the 2201 layers was increased. The unit cell/unit cell superlattice showed T_{c zero} of 30 K.     

Influence of N2:(N2 + Ar) flow ratio and substrate temperature on the properties of zirconium nitride films prepared by reactive dc magnetron sputtering

Preferred crystal orientation and low electrical resistivity are required for ZrN_x films applied in electronic devices. In this paper, effects of N₂:(N₂+Ar) flow ratio (F(N₂)) and substrate temperature on the properties of the films deposited on glass substrate by reactive dc sputtering are investigated. In a wide range of F(N₂) (4–24%), the films show fcc NaCl structure. While for F(N₂) in the ranges of 5–12, 12–24 and >24%, the films show (1 1 1)/(2 0 0), (1 1 1) only and amorphous structures, respectively. The electrical resistivity increases with F(N₂) from 5 to 24%, and can be controlled to some extent by changing the substrate temperature.     

SiO2 passivation film effects on microwave characteristics of YBa2Cu3O7−x-based resonators

SiO₂ film coated as a passivation layer for YBa₂Cu₃O_7−x (YBCO)-based microwave devices is investigated by measuring the microwave characteristics of microstrip line resonators. The SiO₂ film is deposited with its 0.3 to 0.4 μm thickness by a sputtering method using Ar + 30%O₂ plasma. These deposition conditions do not degrade the microwave characteristics and the critical temperature (T_c). Next, the SiO₂ film coated resonators are compared with the uncoated ones for two kinds of degradation conditions: a 200°C annealing in air, and an exposure to air at 85°C and 85% RH (relative humidity). We find that the SiO₂ passivation film prevents the YBCO thin film from the surface degradation and reacting with water.     

Passivation of TiO2 by ultra-thin Al-oxide

The passivation of sol–gel TiO₂ by ultra-thin layers of Al-oxide has been investigated using transient and spectral photovoltage (PV) techniques. The ultra-thin layers of Al-oxide were prepared by the ion-layer gas reaction (ILGAR) technique and modified by thermal treatments in air, vacuum or Ar/H₂S atmosphere. The samples where characterized by elastic recoil detection analysis (ERDA), X-ray photoelectron spectroscopy (XPS), and contact potential difference (CPD) technique. Without an Al-oxide surface layer, electronic states in the forbidden gap of TiO₂ are formed during thermal treatments in vacuum and Ar/H₂S. The trap density is strongly reduced at the TiO₂/Al-oxide interface. The formation of electronic defects is prevented by a closed ultra-thin layer of Al-oxide.     

Normal-state transport properties of Ba1−xKxBiO3 crystals

The normal-state transport properties of Ba_1−xK_xBiO₃ crystals with a wide range of potassium compositions (0≤x≤0.62) were studied. Although the host material BaBiO₃ has a monoclinic structure, the system changes from a monoclinic to an orthorhombic structure with a small doping of potassium (0≤x<0.35) and behaves similar to a doped semiconductor, without exhibiting superconductivity. In the composition range, holes are majority carriers in the transport phenomena. When x exceeds a critical value (0.35), the system goes into a cubic superconducting phase with a single metallic band. The vicinity of the critical composition transport phenomena is easy to understand assuming the existence of two conducting channels that are made up of metallic and semiconducting phases. Maximum T_c exceeding 30 K was observed at x0.4, where carrier density was at its maximum. Overdoping with potassium suppresses superconductivity. In the metallic composition of x>0.45, transport seems to correlate with the phonon mode with an energy distribution of 15–43 meV.     

Observation of unrecoverable domains in two-dimensional-arrayed Pr0.5Ca0.5MnO3−y junctions

Two-dimensional-arrayed 14×14 sandwich-type junctions of Au–Pr_1−xCa_xMnO_3−y (PCMO, x=0.5)–SrRuO₃ were fabricated on SrTiO₃ (0 0 1) substrates. The resistivity–voltage (ρ–V) characteristics of each junction was measured by a two-probe method. The junctions that return to the insulating state after removing the voltage (recoverable) and the ones that remain metallic (unrecoverable) were found to co-exist in one PCMO film. The variation in the lattice constant of the PCMO film, rather than the variation of the composition, is thought to be related to the separation of recoverable–unrecoverable domains. Among several samples with a PCMO layer fabricated under various conditions, the junctions with thin PCMO layers deposited at low temperature showed a pronounced hysteresis in their ρ–V characteristics. The clear hysteresis and good crystallinity of PCMO films were correlated.     

Photocurrent in superconducting YBa2Cu3O7−x films induced by an infrared free electron laser

Since the discovery of high-temperature cuprate superconductors, there has been much intensive study about the mechanism of them. However, identifying the dynamical mechanism behind them remains one of the great challenges in condensed matter physics. We investigated the high-temperature YBa₂Cu₃O_7−x superconducting films by using a free electron laser (FEL). The method is a type of photoelectron spectroscopy called a free electron laser internal photoemission. The spectrum of the photocurrent induced by FEL was measured in the case of 15 K and 100 K. We estimated the superconductive gap energy of YBa₂Cu₃O_7−x by comparing the photocurrent spectrum of the superconductive state with that of non-superconductive state.     

层数变化对堆叠生长的MoS_(2(1-x))Se_(2x)电子结构的影响

二维过渡金属硫化物因其独特的光电特性在多功能光电器件方面具有广泛的应用前景.为了进一步拓展其在微纳光电子器件方面的应用范围,并提高器件性能,人们开展了通过合金手段改变端组分材料配比实现对二维半导体材料带隙调控的带隙工程以及调控生长条件改变材料形貌和结构的缺陷工程研究.本文利用光学、原子力和扫描电子显微镜等设备以及拉曼和光致发光光谱等手段对由化学气相沉积法生长出来的堆叠状MoS_(2(1-x))Se_(2x)合金的性质进行了研究.不同于大多数单层或少层MoS_(2(1-x))Se_(2x)合金的情况,堆叠生长的阶梯状MoS_(2(1-x))Se_(2x)合金材料在厚度从2.2 nm (约3层)一直增加到5.6 nm (约7层)时都显出了较强的发光特性,甚至在100 nm厚时,样品的发光谱线仍具有两个发光峰.两个激子发光峰分别来源于自旋轨道耦合造成的价带劈裂.随着厚度的增加,两个峰都逐渐红移,显示了合金掺杂时的能带弯曲效应.拉曼光谱给出了类MoS_2和类MoSe_2两套振动模.随着厚度的增加,拉曼峰位几乎不移动,但面内的两个振动模E_(2g(Mo-Se))和E_(2g(Mo-s))逐渐显现并增强.显然缺陷和应力是影响堆叠生长MoS_(2(1-x))Se_(2x)合金样品电子结构的主要因素,这为特殊功能器件的制备和可控缺陷工程的研究提供了有益的参考.     

Ferromagnetic Zr1−xMnxCo2 laves phase compounds

Structure and magnetic properties of the Zr_1−xMn_xCo_2+δ alloys were studied for 0 x <0.7, δ=0, 0.45. The cubic C15 Laves phase structure shows Mn solubility up to x≈0.4. The other Laves phase with the hexagonal C36 structure found for x0.5 apparently has a small region of Mn solubility in the vicinity of Zr_0.4Mn_0.6Co₂. Though the parent Mn-free compounds are known to be paramagnetic, the Mn-substituted alloys show ferromagnetic behavior with the Curie temperatures up to 625 K and the room-temperature saturation magnetization of about 100 emu/g. The onset of ferromagnetism with the Mn substitution for Zr may be caused by polarization of itinerant 3d electrons, like it was earlier supposed for the off-stoichiometric ZrCo_2+δ. The universal composition dependencies of the intrinsic magnetic properties for different δ can be obtained, if plotted against the amount of zirconium atoms missing in its sublattice. The room-temperature anisotropy with the noticeable anisotropy field of 24 kOe and the 1 1 0 easy magnetization direction laying in a basal plane was found in the hexagonal Zr_0.5Mn_0.5Co₂.     

Superconductivity due to charge transfer to the CuO2 sheet from the (Tl,Pb) O layer in Tl0.5Pb0.5Sr2−xNdxCuO5−δ

The superconductivity of Tl_0.5Pb_0.5Sr_2−xNd_xCuO_5−δ was observed for x ≥ 0.3, although the calculated Cu valence assuming Tl³⁺ and Pb⁴⁺ is slightly above or below 2.0. The binding energy of the Tl and Pb 4f core levels measured by XPS shifted to higher energy than those of Tl³⁺ and Pb⁴⁺ in the reference materials, showing that the Tl and Pb valences are lower than 3 + and 4 +, respectively. These observations strongly suggest that holes in the CuO₂ sheet are created by charge transfer from the (Tl,Pb)O layer, similar to the double-layered Tl---Ba cuprates.

In contrast, the temperature variation of electrical conductivity of Tl_0.5Pb_0.5Sr₂CuO_5−δ changed from metallic to semiconducting with increasing oxygen deficiency, δ, and no superconductivity was observed through any control of δ. Although XPS measurement also suggested that Tl and Pb valences lowered with increasing oxygen deficiency, δ, the reason why the system did not show superconductivity can be understood by the depletion of oxygen from the CuO₂ plane during deoxygenation.     

Temperature dependence of induced magnetic anisotropy in metallic glasses (Fe1 − xCox)78Si10B12

The variations of induced magnetic anisotropy with annealing and measuring temperatures in metallic glasses (Fe_{1 − x}Co_x)₇₈Si₁₀B₁₂ have been measured. It was found that K_u (T) was proportional to Mⁿ_s (T) for T below 200°C, and the index n varied with the cobalt content x and annealing conditions, not being smaller than 3. To the predictions of the existing pair-ordering and single-ion theories, the above results are anomalous. By considering the distributions of exchange integrals and activation energies in metallic glasses, this anomalous behaviour could be explained properly.     

铜钨合金高温高压性质的第一性原理研究

采用基于密度泛函理论的第一性原理方法,研究了三种不同比例铜钨合金(Cu3W,Cu W,Cu W3)的基态及高温、高压下的电子结构、弹性性质和热力学性质.弹性常数计算结果表明Cu3W为结构不稳定相,Cu W和Cu W3为结构稳定相,与声子色散曲线得到的结论一致.通过对态密度的分析,发现随压强的增大,金属键键能增大,并且态密度有向深能级移动的趋势.通过准简谐德拜模型和准简谐近似模型分别计算、分析和对比了三种铜钨合金在不同温度和压强下的体弹模量、热膨胀系数、德拜温度和比热容.     

Out-of-plane conductivity in Bi2Sr2CuOy crystals

We present extensive measurements of anisotropic resistivity on Bi₂Sr₂CuO_y crystals grown from melts with different Bi/Sr ratios and doped with Pb. We find that the temperature variation of the c-axis resistivity _c(T) is correlated with the in-plane resistivity _ab. Depending on the starting compositions, the normal-state in-plane resistivity _ab can either show localized conduction at low temperature or be metallic (d_ab/dT < 0) in the whole temperature range. Correspondingly, a change of the T dependence of _c from nonmetallic (d_c/dT < 0) in the whole measured temperature range (4.2–300 K) to a mixed (d_c/dT < 0 at low T but d_c/dT> 0 at high T) conduction is observed. In accompany, the magnitude of _c at low T decreases by about two orders. We have quantified the trend of the _c(T) and examined some current proposals concerning the out-of-plane transport.