PIN型和NIP型硅薄膜太阳电池中绒面陷光结构和陷光性能研究

对于硅薄膜太阳电池来说, 无论是PIN型还是NIP型太阳电池, 采用绒面陷光结构来提高入射光的有效利用率是提高太阳电池效率的重要方法之一.本文采用标度相干理论对PIN和NIP型电池的绒面结构的陷光性能进行了数值模拟. 结果表明: PIN电池中前电极和NIP电池中背电极衬底粗糙度分别为160和40 nm时可获得理想的陷光效果; 在不同粗糙度背电极衬底上制备a-SiGe:H电池发现, 使用40和61.5 nm 背电极可获得相当的短路电流密度, 理论分析和实验得到了一致的结果. 关键词： 陷光结构 光散射能力 标量相干理论 硅基薄膜太阳电池     

基于阳极氧化铝纳米光栅的薄膜硅太阳能电池双重陷光结构设计与仿真

本文提出了表面和底部均带有阳极氧化铝(AAO)纳米光栅的薄膜硅太阳能电池双重陷光结构,利用FDTD软件仿真研究了AAO纳米光栅的周期、厚度和占空比对薄膜硅太阳能电池短路电流密度的影响,并对AAO结构参数进行了优化.仿真结果表明,表面AAO最佳结构参数是周期440 nm,厚度75 nm,占空比0.5,底部AAO最佳结构参数是周期380 nm,厚度90 nm,占空比为0.75.双重AAO组合陷光结构可有效增加薄膜硅太阳能电池在280—1100 nm范围内的光吸收,吸收相对增强可以达到74.44%.     

Unlinking absorption and haze in thin film silicon solar cells front electrodes

We study the respective influence of haze and free carrier absorption (FCA) of transparent front electrodes on the photogenerated current of micromorph thin film silicon solar cells. To decouple the haze and FCA we develop bi‐layer front electrodes: a flat indium tin oxide layer assures conduction and allows us to tune FCA while the haze is adjusted by varying the thickness of a highly transparent rough ZnO layer. We show how a minimum amount of FCA leads only to a few percents absorption for a single light path but to a strong reduction of the cell current in the infrared part of the spectrum. Conversely, a current enhancement is shown with increasing front electrode haze up to a saturation of the current gain. This saturation correlates remarkably well with the haze of the front electrode calculated in silicon. This allows us to clarify the requirements for the front electrodes of micromorph cells. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Light scattering of nanocrystalline TiO2 film used in dye-sensitized solar cells

This paper studies the light scattering and adsorption of nanocrystalline TiO2 porous films used in dye-sensitized solar cells composed of anatase and/or rutile particles by using an optical four-flux radiative transfer model. These light properties are difficult to measure directly on the functioning solar cells and they can not be calculated easily from the first-principle computational or quantitative theoretical evaluations. These simulation results indicate that the light scattering of 1 25 nm TiO2 particles is negligible, but it is effective in the range of 80 and 180 nm. A suitable mixture of small particles （10 nm radius）, which are resulted in a large effective surface, and of larger particles （150 nm radius）, which are effective light scatterers, have the potential to enhance solar absorption significantly. The futile crystals have a larger refractive index and thus the light harvest of the mixtures of such larger rutile and relatively small anatase particles is improved in comparison with that of pure anatase films. The light absorption of the 10μm double-layered films is also examined. A maximal light absorption of double-layered film is gotten when the thickness of the first layer of 10 urn-sized anatase particles is comparable to that of the second larger rutile layer.     

周期结构表面散射系数测试及修正方法*

无规入射散射系数是描述结构声反射特性的重要参数,在周期结构等典型扩散体的声学设计和室内声场模拟中具有重要的作用。本文给出了混响室法测试无规入射散射系数的原理,对正弦型周期结构进行了实验测试,并针对测试中存在的缺陷,提出了一种考虑空气间隙吸声的修正方法,经验证具有较好的修正效果。     

A glass thinning and texturing method for light incoupling in thin‐film polycrystalline silicon solar cells application

For polycrystalline silicon (poly‐Si) thin‐film solar cells on ～3 mm borosilicate glass, glass thinning reduces the glass absorption and light leaking to neighbouring cells; the glass texturing of the sun‐facing side suppresses reflection. In this Letter, a labour‐free wet etching method is developed to texture and thin the glass at the same time in contrast to conventionally separated labour‐intensive glass thinning and texturing processes. For 2 cm² size poly‐Si thin‐film solar cells on glass superstrate, this wet etching successfully thins down the glass from 3 mm to 0.5 mm to check the ultimate benefit of the process and introduces a large micron texture on the sun‐facing glass surface. The process enhances J_sc by 6.3% on average, with the optimal J_sc enhancement of 8%, better than the value of 4.6% found in the literature. This process also reduces the loss in external quantum efficiency (EQE loss), which is due to light leaking to neighbouring cells, dramatically. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

The specular component of light scattering and the charac- terization of the height distribution for random surfaces

The relations between the specular reflection component of the intensity scattered by random surfaces and the height distributions of the surfaces are analyzed theoretically. In the extraction of the height distribution, both the phase and the amplitude of the specular wave are required. The measured specular intensity data versus the perpendicular component of the wave vector are used for the retrieval of the phase distribution of the specular wave, in which the Ger-chberg-Saxton iterative algorithm is employed, and the characterization of the height distribution of random surfaces is accomplished. In the experiment, two samples with Gaussian and quasi-two level height distributions, respectively, are practically measured and the results of the height probability density function obtained by light scattering method are in good accordance with those by atomic force microscopy. The method of this paper is of important significance for the characterizations and studies of random surfaces.     

用蒙特卡罗方法计算光通过薄层随机分布粒子的散射

本文利用蒙特卡罗方法计算准直光束通过薄层随机分布粒子散射的透射和反射光强,并和输运理论的扩散近似结果做了比较。当散射接近各向同性时两者符合良好。当散射明显地成为各向异性时,蒙特卡罗方法的结果是合理的,而输运理论的扩散近似失效。     

Initial growth of intrinsic microcrystalline silicon thin film: Dependence on pre-hydrogen glow discharge and substrate surface morphology

We found the decreases of amorphous incubation volume from Raman spectra and surface roughness from AFM in hydrogenated microcrystalline silicon (μc-Si:H) films deposited with a pre-hydrogen glow discharge. The above phenomena are attributed to the increase in the nuclei density as observed by AFM measurements. Substrate surface morphology of eagle2000 glass modified by wet etching also has a positive effect on the nucleation and crystalline formation. In addition, μc-Si:H doped layer is also beneficial for decreasing the amorphous incubation layer thickness because of surface roughness and crystallinity in the μc-Si:H doped layer.     

前后光栅周期对于双光栅结构薄膜太阳能电池光俘获效应的影响

本文用时域有限差分法对硅层等效厚度为100 nm的具有不同前后光栅周期的介质/金属双光栅结构薄膜太阳能电池进行了模拟分析,比较了三角形最佳相同与不同周期光栅结构的吸收光谱特性,分析了光栅高度、填充比、硅吸收层厚度对最佳相同和不同周期光栅结构光吸收特性的影响,以及相应结构中导致光吸收增强的共振模式.结果表明前后光栅周期为1:1的共形双光栅结构中存在光泄漏现象,偏离1:1后的光栅结构可有效地抑制低级次衍射光的泄漏,前光栅周期小于后光栅周期的结构光吸收性能的提高来自于平面波导模式在吸收层中的有效激发和传播,而前光栅周期大于后光栅周期的结构光吸收性能的提高则来自于后光栅界面上所激发的等离子体极化模式.在较厚的硅吸收层厚度,前后光栅周期比为1:2和1:3的电池结构也会出现光泄漏现象,从而使具有最大光吸收效率的结构偏离这些周期比结构的位置.     

薄膜硅/晶体硅异质结电池中本征硅薄膜钝化层的性质及光发射谱研究

本文采用甚高频等离子体化学气相沉积技术 (VHF-PECVD) 制备薄膜硅/晶体硅异质结电池中的本征硅薄膜钝化层, 光发射谱 (OES) 测量技术研究了硅薄膜沉积过程中等离子体发光谱随时间的变化. 结果表明: 在实验优化条件下等离子体发光谱很快达到稳定 (大约25 s), 并且SiH^*/H_α^* 的比值随时间变化较小, 避免了生长过程中硅薄膜结构的不均匀性, 这主要是SiH₄没有完全耗尽避免了SiH₄的反向扩散. 进一步研究了沉积参数对稳态发光谱和硅薄膜性质的影响, 结果表明: 随着硅烷浓度增加, H_α^*峰强度减小, SiH^*峰强度增加, 薄膜从微晶转变成非晶, 非晶硅薄膜钝化效果好; 随着沉积气压增大, H_α^*和 SiH^*峰强度先增加后减小, 高气压下H_α^*和 SiH^*峰强度下降主要是反应前驱物的聚合形成高聚合物, 不利于形成高质量的硅薄膜, 因此钝化效果下降; 随着反应功率密度增加, H_α^*和 SiH^*峰强度增大, 当功率密度为150 mW/cm² 趋于饱和, 硅薄膜的致密度和钝化效果也开始下降, 50 mW/cm²的低功率密度下硅薄膜钝化效果差可能是由于原子H 浓度低, 不能完全钝化单晶硅表面的悬挂键. 关键词： 薄膜硅 异质结 光发射谱 钝化     

化学气相沉积中影蔽效应对硅薄膜表面形貌和微结构的影响

采用斜入射热丝化学气相沉积技术(OAD-HWCVD),研究了气流入射角度(θ)对氢化非晶硅(a-Si:H)薄膜表面和微结构的影响.实验发现,薄膜厚度为1μm时,均方根粗糙度与tanθ成指数关系;在入射角度为75°时,薄膜表面由自仿射表面转变为mound表面.采用拉曼谱和红外谱表征了硅薄膜的微结构随气流入射角度的变化.在薄膜转变为mound表面生长之前,随入射角度的增加,准局域的影蔽效应使得薄膜中微空洞的数目及尺寸增加,导致薄膜微结构因子升高、致密度下降、薄膜质量变差.在薄膜转变为mound表面生长之后,非局域的影蔽效应导致大尺度的空洞,同时薄膜中以Si-Hn(n 2)形式存在的氢增多.本文以非晶硅薄膜为例,结合标度理论,分析了薄膜生长过程中的表面形貌和微结构与影蔽效应的关系.     

太阳电池用本征微晶硅材料的制备及其结构研究

采用VHF-PECVD技术制备了系列不同硅烷浓度和反应气压的微晶硅薄膜.运用拉曼散射光谱和 x射线衍射对制备的材料进行了结构分析.在实验研究的范围内，制备材料的晶化程度随硅烷 浓度的增加而降低.XRD的测试结果表明：制备的微晶硅材料均体现了(220)方向择优.应用在 电池的有源层中，制备出了效率达7.1%的单结微晶硅太阳电池，电池的结构是glass/ZnO/p( μc-Si:H)/i(μc-Si:H)/n(a-Si:H/Al)，没有ZnO背反射电极，有源层的厚度仅为1.2μm. 关键词： 本征微晶硅薄膜 拉曼光谱 x射线衍射     

Photonic nanostructures for advanced light trapping in silicon solar cells: the impact of etching on the material electronic quality

Dry plasma etching, commonly used by the Photonics community as the etching technique for the fabrication of photonic nanostructures, could be a source of device performance limitations when used in the frame of silicon photovoltaics. So far, the lack of silicon solar cells with state‐of‐the‐art efficiencies utilizing nanophotonic concepts shows how challenging their integration is, owing to the trade‐off between optical and electrical properties. In this study we show that dry plasma etching results in the degradation of the silicon material quality due to (i) a high density of dangling bonds and (ii) the presence of sub‐surface defects, resulting in high surface recombination velocities and low minority carrier lifetimes. On the contrary, wet chemical anisotropic etching used as an alternative, leads to the formation of inverted nanopyramids that result in low surface recombination velocity and low density of dangling bonds. The proposed inverted nanopyramids could enable high efficiency photonic assisted solar cells by offering the potential to achieve higher short‐circuit current without degrading the open circuit voltage. (© 2016 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Nanoimprint texturing of transparent flexible substrates for improved light management in thin‐film solar cells

We present a nanoimprint based approach to achieve efficient light management for solar cells on low temperature transparent polymer films. These films are particularly low‐priced, though sensitive to temperature, and therefore limiting the range of deposition temperatures of subsequent solar cell layers. By using nanoimprint technology, we successfully replicated optimized light trapping textures of etched high temperature ZnO:Al on a low temperature PET film without deterioration of optical properties of the substrate. The imprint‐textured PET substrates show excellent light scattering properties and lead to significantly improved incoupling and trapping of light in the solar cell, resulting in a current density of 12.9 mA/cm², similar to that on a glass substrate. An overall efficiency of 6.9% was achieved for a flexible thin‐film silicon solar cell on low cost PET substrate. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

光源的偏振态对动态光散射颗粒测量结果的影响

研究了在动态光散射纳米颗粒测量中,光源的偏振态对测量结果的影响。采用了粒径为100nm、体积浓度为0.5%的标准颗粒作为样品,使He-Ne激光通过起偏器得到0°～180°方向的偏振光,测量了散射光强、偏振度和粒径测量值的变化,计算了相应的粒径均值偏差和标准差,并将这一结果与无偏振He-Ne激光入射进行了比较。结果表明,当入射光为线偏振光时,偏振方向垂直于散射面时测量效果最好;另一方面,由于颗粒系散射迭加造成的散射光偏振度降低,使线偏振光源与无偏振光源产生的散射光偏振度无明显差别,证明在测量中可以使用无偏振He-Ne激光代替。     

Morphology and structure of gold-lithium niobate thin film: A laboratory source X-ray scattering study

Laboratory source X-ray scattering set-up has been used to determine the complete morphology and structure of an optically important composite thin film. Analysis of grazing incidence small angle X-ray scattering, X-ray reflectivity and powder diffraction data of Au/LiNbO₃ thin film prepared by sequential deposition of gold and lithium niobate on float glass substrate suggest that the Au-nanocrystallites are dispersed in amorphous medium, which although have average separation but do not have any long range periodicity other than growth or z-direction. The morphology of the nanocomposite thin film determined through X-ray scattering measurements agrees well with the measured optical absorption.     

微晶硅锗薄膜作为近红外光吸收层在硅基薄膜太阳电池中的应用

采用射频等离子体增强化学气相沉积技术,制备了具有一定晶化率不同Ge含量的氢化微晶硅锗(μcSi1-xGex:H)薄膜.通过Ⅹ射线荧光谱、拉曼光谱、X射线衍射谱、傅里叶红外谱、吸收系数谱和电导率的测试,表征了μc-Si_(1-x)Ge_x:H的材料微结构随Ge含量的演变.研究表明:提高Ge含量可以增强μc-Si_(1-x)Ge_x:H薄膜的吸收系数.将其应用到硅基薄膜太阳电池的本征层中可以有效提高电池的短路电流密度(J_(sc)).特别是在电池厚度较薄或陷光不充分的情况下,长波响应的提高会更为显著.应用ZnO衬底后,在Ge含量分别为9%和27%时,μc-Si_(1-x)Ge_x:H太阳电池的转换效率均超过了7%.最后,将μc-Si_(1-x)Ge_x:H太阳电池应用在双结叠层太阳电池的底电池中,发现μc-Si_(0.73)Ge_(0.27):H底电池在厚度为800 nm时即可得到比1700 nm厚微晶硅(μc-Si:H)底电池更高的长波响应.以上结果体现μc-Si_(1-x)Ge_x:H太阳电池作为高效近红外光吸收层,在硅基薄膜太阳电池中应用的前景.