The dynamic characteristics of harvesting energy from mechanical vibration via piezoelectric conversion

As an alternative power solution for low-power devices, harvesting energy from the ambient mechanical vibration has received increasing research interest in recent years. In this paper we study the transient dynamic characteristics of a piezoelectric energy harvesting system including a piezoelectric energy harvester, a bridge rectifier, and a storage capacitor. To accomplish this, this energy harvesting system is modeled, and the charging process of the storage capacitor is investigated by employing the in-phase assumption The results indicate that the charging voltage across the storage capacitor and the gathered power increase gradually as the charging process proceeds, whereas the charging rate slows down over time as the charging voltage approaches to the peak value of the piezoelectric voltage across the piezoelectric materials. In addition, due to the added electrical damping and the change of the system natural frequency when the charging process is initiated, a sudden drop in the vibration amplitude is observed, which in turn affects the charging rate. However, the vibration amplitude begins to increase as the charging process continues, which is caused by the decrease in the electrical damping （i.e., the decrease in the energy removed from the mechanical vibration）. This electromechanical coupling characteristic is also revealed by the variation of the vibration amplitude with the charging voltage.     

Prompt efficiency of energy harvesting by magnetic coupling of an improved bi-stable system

In order to improve the transform efficiency of bi-stable energy harvester(BEH),this paper proposes an advanced bi-stable energy harvester(ABEH),which is composed of two bi-stable beams coupling through their magnets.Theoretical analyzes and simulations for the ABEH are carried out.First,the mathematical model is established and its dynamical equations are derived.The formulas of magnetic force in two directions are given.The potential energy barrier of ABEH is reduced and the snap-through is liable to occur between potential wells.To demonstrate the ABEH's advantage in harvesting energy,comparisons between the ABEH and the BEH are carried out for both harmonic and stochastic excitations.Our results reveal that the ABEH's inter-well response can be elicited by a low-frequency excitation and the harvester can attain frequent jumping between potential wells at fairly weak random excitations.Thus,it can generate a higher output power.The present findings prove that the ABEH is preferable in harvesting energy and can be optimally designed such that it attains the best harvesting performance.     

外加磁场压电悬臂梁能量采集系统的磁化电流法磁力研究

以外加磁场压电悬臂梁能量采集系统结构为研究对象, 根据磁化电流方法探讨了具有悬臂梁特征的系统结构的磁场作用力及其计算方法, 给出了相应的磁力计算模型, 并将计算结果与实验数据进行了对比. 研究表明, 磁化电流方法导出的磁力计算模型存在偏差, 其磁力计算误差随着磁铁间距缩小而增大. 通过引入悬臂梁末端磁铁的偏转角度, 对磁化电流法计算模型进行改进, 得到合理的外加磁场压电悬臂梁能量采集系统的磁力计算模型, 为该能量采集系统的进一步研究提供了可靠的磁力计算理论依据.     

随机激励下双稳态压电俘能系统的相干共振及实验验证

随着压电晶体材料的迅速发展, 基于压电效应的能量采集系统是俘获环境中的宽带随机振动能量的一种有效途径. 研究了有限宽带随机激励作用下, 磁斥力双稳态压电俘能系统的相干共振俘能机理, 并进行了实验验证. 运用Euler-Maruyama方法求解了随机非线性压电振动耦合方程, 比较分析了相干共振发生前后系统的动力学特性和俘能效率, 然后基于Kramers逃逸速率解释了相干共振. 最后的随机振动实验结果验证了双稳态压电俘能系统的相干共振俘能机理. 并且观察到: 当相干共振发生时, 系统会在两个势能阱之间剧烈运动, 此时宽带随机振动能量会被转化为大幅值窄带低频振动响应, 从而极大地提高了宽带随机振动能量的俘获效率.     

带碰撞双稳态压电俘能系统的俘能特性研究

双稳态俘能系统的运动常常会陷入单个势能阱中, 导致俘能效率降低. 为了解决这个问题, 本文提出了一类带碰撞的磁斥力双稳态压电振动能量采集系统. 建立了该碰撞双稳态系统的机电耦合方程, 分析了碰撞对双稳态系统动力学特性的影响. 研究了确定性激励和低强度随机激励下碰撞对系统响应特性和俘能效率的影响. 结果表明: 简谐激励下, 碰撞能够使得原双稳态系统的单阱小幅周期运动转变为双阱间的大幅运动, 从而有效地提高输出功率. 得到了低强度随机激励下, 不同碰撞间隙对系统动力响应特性和输出功率的影响规律. 对一个给定的随机激励, 存在一个最优的碰撞间隙, 此时碰撞能够将原双稳态系统单阱内的随机运动转化为频繁的双阱跳跃, 出现大幅值运动, 从而大幅提高了系统的俘能效率.     

基于磁化电流法的双稳压电悬臂梁磁力精确分析

双稳压电悬臂梁结构常常用于振动能量采集系统,其中的非线性磁力与系统势函数和动力学方程的建立紧密相关,非线性磁力的正确分析和精确计算对系统振动响应和能量采集效果的准确预测至关重要.本文采用形状函数分析方法,通过悬臂梁弯曲斜率的整体积分计算,得到了悬臂梁末端的运动轨迹及其末端磁铁精确的位置与姿态,并由此根据磁化电流理论建立了双稳压电悬臂梁能量采集系统的磁力计算模型,给出了末端磁铁受到的水平轴向磁力和竖直纵向磁力及其合磁力的变化规律.数值模拟发现,随着末端磁铁竖直纵向位移逐渐增大,磁铁受到的水平轴向磁力和竖直纵向磁力都会依次由排斥力转变为吸引力,从而导致磁力合力的方向会随磁铁位移发生跨越两个象限的大幅度变化.实验验证表明,磁力计算结果与实验测量结果符合良好,其精确度优于现有文献方法的精度,因此本文的方法可以准确预测双稳压电悬臂梁振动过程的磁力变化规律.     

采用磁电换能器的振动能量采集器

采用磁致伸缩/压电层合磁电换能器设计了一个振动能量采集器,该能量采集器采用悬臂梁作为振动敏感机构,并用四个NdFeB磁铁组成磁路放在悬臂梁末端.该磁路在空气隙中产生梯度较大的非均匀磁场,使得磁电换能器在较小的振动下感应到较大的磁场变化量,输出较高的功率.利用等效磁荷理论,分析了空气隙磁场分布以及振动时磁路受到的磁力,并用林斯泰特-庞加莱法研究了能量采集器的非线性振动特性,同时将能量采集器的振动方程和换能器的磁电特性结合,分析了能量采集器谐振时的机-磁-电转换特性.通过实验表明：理论与实验符合得较好,且在加 关键词： 振动能量采集 磁致伸缩/压电层合材料 机磁电转换 非线性振动     

悬臂梁压电振子宽带低频振动能量俘获的随机共振机理研究

研究了利用系统非线性来提高悬臂梁压电振子宽带低频振动能量俘获效率的随机共振机理,通过增加一对矩形永磁铁对传统线性悬臂梁压电振子结构进行了改进,结果揭示:在外部非线性磁力作用以及合适的磁铁间距条件下,这种外加磁力悬臂梁压电振子会构成一个双稳系统,在外部宽带低频随机振动源激励下发生随机共振现象,且发生随机共振时的输出电压明显增大,从而可以扩展悬臂梁压电振子的共振频率范围、提高低频振动能量的转化输出. 关键词： 压电悬臂粱 振动能量俘获 宽带低频 随机共振     

非线性磁式压电振动能量采集系统建模与分析

为便于评价、优化磁式压电振动能量采集系统的性能,系统研究了该类系统的建模与分析方法,建立了非线性的分布参数模型用于描述系统的非线性动力学行为,并采用谐波平衡法给出了谐波响应的解析解.随后利用仿真模型分析了磁铁间距、加速度幅值、负载阻抗对输出功率的影响,比较了不同激励频率和加速度幅值下的最优阻抗.结果表明:双稳态特性适用于低强度的振动环境,且愈接近临界区域,输出功率愈高,而单稳态渐硬特性适用于高强度振动环境,其最优间距并不靠近临界区域;阱间大幅运动和阱内小幅运动均存在高低能量态共存的现象,愈接近临界区域,现象愈明显;激振频率是影响最优负载阻抗的决定性因素.     

弹性支撑双稳压电悬臂梁振动响应及能量采集研究

在分析了常规刚性支撑非线性能量采集系统的研究基础上,提出外部磁铁弹性支撑的结构设想,保证系统在低强度激励条件下也能处于双稳态振荡,提高机电能量转换效率.研究表明,对于强度变化的随机激励历程,弹性支撑非线性能量采集系统不需要实时调整磁铁间距,能够更好地迎合强度时刻变化的随机激励源,实现高效的机电能量转换.     

Analysis of thermal energy harvesting using ferromagnetic materials

This Letter aims at giving a preliminary investigation of the thermal energy harvesting capabilities of a technique using the temperature-dependent permeability of ferromagnetic materials. The principles lie in the modification of the magnetic field caused by the variation of the permeability due to the temperature change, hence generating a voltage across a coil surrounding the circuit. The technique can be made truly passive by the use of magnets for applying bias magnetic field. Theoretical results, validated by experimental measurements, show a voltage output of 1.2 mV at optimal load of 2 Ω under 60 K temperature variation in 5 s (with a maximum slope of 25 K s⁻¹). Further improvements, such as the use of low resistivity coil and magnet with high remnant magnetic field, indicate that it is possible to convert up to 7.35 μJ cm⁻³ K⁻² cycle⁻¹.     

Electrostatic energy harvesting enhancement using variable equivalent permittivity

This Letter exposes an electrostatic-based vibration energy scavenging scheme using a two-layer configuration made of a high permittivity material and a low permittivity layer of variable thickness. Because of the significant change in the permittivity allowed by this process, the capacitance ratio variation is much larger than in the case of a single layer (whatever the permittivity of the latter), therefore allowing an increased efficiency and a significant energy gain, by a typical factor of 50.     

Stacked and folded piezoelectrets for vibration-based energy harvesting

ABSTRACT

Vibration-based energy harvesting with piezoelectrets can be significantly improved by using multiple layers of these materials. In particular, folding or stacking of piezoelectrets or a combination of these methods results in increased power output of the energy harvesters. The possibilities of these procedures are explored, together with the effect of seismic mass, resonance frequency, and terminating resistance. It is found that with seismic masses of about 20 g and using radiation-crosslinked polypropylene (IXPP) as a piezoelectret, power outputs of up to 80 µW can be achieved for an acceleration of 1 g. Expected dependencies of generated power on frequency, folding and stacking parameters, in particular number of layers, and on seismic mass, are confirmed.     

窄带随机激励双稳压电悬臂梁响应机制与能量采集研究

具有中心频率的窄带随机振动是一种典型的环境振动,其振动特征与环境的变化密切相关.本文以双稳压电悬臂梁能量采集系统为研究对象,分析系统在不同磁铁间距下的等效线性固有频率特性,以带通滤波器输出一定带宽的窄带随机激励模拟环境振动,研究系统的响应和能量采集特征.研究表明,对于一定带宽的窄带随机激励,一方面系统始终存在一个固定的磁铁间距使其输出达到峰值,另一方面当激励中心频率在一定范围内变化时,系统还分别存在另外两个或一个不同磁铁间距也能使系统输出达到峰值,而且该峰值特性是系统在其等效线性固有频率处诱导双稳或单稳“共振”形成的.研究结果可为具有窄带随机激励特征的振动能量采集提供一定的理论和技术支持.     

基于幂次相互作用的二维磁性团簇耦合能研究

在扩散限制凝聚模型基础上,采用Monte Carlo方法模拟了磁耦合作用随粒子间距离幂次变化的磁性粒子动力学凝聚过程.重点研究了在不同幂指数α值下团簇在生长过程中,即随着粒子数N的增加,团簇平均耦合能E_c(N)的演化过程.模拟结果表明:对于α≥5时,E_c(N)随着粒子数N的增加变化较小;当α=2时,E关键词： 扩散限制凝聚模型 幂次相互作用 耦合能     

Broad-band polarization-independent metamaterial absorber for solar energy harvesting applications

A novel broad-band polarization-independent with wide-angle metamaterial absorber(MA) is investigated and demonstrated for solar energy harvesting applications. The proposed MA is composed of two metal layers which have different thickness and a dielectric layer which is sandwiched between these metal layers. By this combination, the proposed MA indicates plasmonic resonance characteristic. Numeric results show that proposed MA has perfect absorption characteristic which is above 88.28% with wide-angle for all visible region. It shows almost perfect absorption of 98.4% at the resonance frequency of 621.76 THz and has also 90% absorption between frequencies of 445 THz and 770 THz which is nearly all visible light region. Besides, numerical results validate that the proposed MA could achieve very high absorption at wide-angles of incidence for both transverse electric (TE) and transverse magnetic (TM) waves.. The proposed MA and its variations enable for solar cell applications due to have upper ratio of 90% in the widest range of visible spectrum comparing to the studies in literature. In order to show additional features of the proposed structure, parametric studies are realized and discussed. Furthermore, the absorption characteristic of proposed MA is investigated for infrared and ultraviolet region. The enhancement of absorption of the structure will provide new type of sensors in these frequency ranges.     

A prototype DC triboelectric generator for harvesting energy from natural environment

A prototype direct current Triboelectric Generator (DC-TEG) has been demonstrated to generate dc voltages by converting rotational mechanical energy into electrical energy. The generator primarily consists of four rotating wheels (two copper electrodes and two triboelectric wheels) utilizing polytetrafluoroethylene (PTFE) tape and nylon fabric as the triboelectric materials in its design. Once subjected to mechanical rotation, the interaction between the two triboelectric materials generates equal, but opposite charges and deposits them on the copper electrodes resulting in a dc voltage across an external load resistor. The power performance of the generator, with changes in angular frequency, has been measured. The DC-TEG can generate a dc voltage of about 1.5 mV across an external load of 15.14 kΩ at a rotational speed of 10 rev/sec. The dependences of current and power on the angular frequency have also been measured. Preliminary results suggest that the relationship between the dc voltage and angular frequency of rotation is quadratic, however further measurements at relatively higher angular frequencies are needed before a proper mathematical model may be established. The work here presents a new, cost-effective DC-TEG design for power scavenging from any naturally or artificially occurring rotational mechanical motion facilitated by either wind or flowing water for self-powered systems.     

Study on signal intensity of low field nuclear magnetic resonance via an indirect coupling measurement

We carry out an ultra-low-field nuclear magnetic resonance (NMR) experiment based on high-T c superconducting quantum interference devices (SQUIDs). The measurement field is in a micro-tesla range (～10 μT-100 μT) and the experiment is conducted in a home-made magnetically-shielded-room (MSR). The measurements are performed by the indirect coupling method in which the signal of nuclei precession is indirectly coupled to the SQUID through a tuned copper coil transformer. In such an arrangement, the interferences of applied measurement and polarization field to the SQUID sensor are avoided and the performance of the SQUID is not destroyed. In order to compare the detection sensitivity obtained by using the SQUID with that achieved using a conventional low-noise-amplifier, we perform the measurements using a commercial room temperature amplifier. The results show that in a wide frequency range (～1 kHz-10 kHz) the measurements with the SQUID sensor exhibit a higher signal-to-noise ratio. Further, we discuss the dependence of NMR peak magnitude on measurement frequency. We attribute the reduction of the peak magnitude at high frequency to the increased field inhomogeneity as the measurement field increases. This is verified by compensating the field gradient using three sets of gradient coils.     

Transverse coupling between two general biisotropic slabs

The general formulation for the determining of transverse coupling behaviour between two different biisotropic slabs is proposed based on the method of conventional field perturbation, and some special cases are considered. Since biisotropic medium is a generalization of the well-studied nonreciprocal and reciprocal chiral media, our results are suitable for much more cases.     

Spin coupling and magnetic field effects on the finite-size free energy and its non-extensivity for 1-D Ising model with nearest and next-nearest neighbor interactions in nanosystem

The effects of second-neighbor spin coupling interactions and a magnetic field are investigated on the free energies of a finite-size 1-D Ising model. For both ferromagnetic of nearest neighbor (NN) and next-nearest neighbor (NNN) spin coupling interactions, the finite-size free energy first increases and then approaches a constant value for any size of the spin chain. In contrast, when NNN and NN spin coupling interactions are antiferromagnetic and ferromagnetic, respectively, the finite-size free energy gradually decreases by increasing the competition factor and eventually vanishes for large values of it. When a magnetic field is applied, the finite-size free energy decreases with respect to the case of zero magnetic fields for both ferromagnetic and antiferromagnetic spin coupling interactions. Deviation of free energy per size for finite-size systems relative to the infinite system increases when the spin coupling interactions as well as the f parameter (the ratio of the magnetic field to NN spin coupling interaction) increase.