An improved EEHEMT model for kink effect on AIGaN/GaN HEMT

In this paper, a new current expression based on both the direct currect （DC） characteristics of the A1GaN/GaN high election mobility transistor （HEMT） and the hyperbolic tangent function tanh is proposed, by which we can describe the kink effect of the A1GaN/GaN HEMT well. Then, an improved EEHEMT model including the proposed current expression is presented. The simulated and measured results of Ⅰ-Ⅴ, S-parameter, and radio frequency （RF） large-signal characteristics are compared for a self-developed on-wafer A1GaN/GaN HEMT with ten gate fingers each being 0.4-μm long and 125-p-m wide （Such an A1GaN/GaN HEMT is denoted as A1GaN/GaN HEMT （10 × 125 μm））. The improved large signal model simulates the Ⅰ-Ⅴ characteristic much more accurately than the original one, and its transconductance and RF characteristics are also in excellent agreement with the measured data.     

AlGaN表面坑状缺陷及GaN缓冲层位错缺陷对AlGaN/GaN HEMT电流崩塌效应的影响

利用金属有机气相外延(MOVPE)技术生长了具有不同AlGaN表面坑状缺陷和GaN缓冲层位错缺陷密度的AlGaN/GaN 高电子迁移率晶体管(HEMT)样品,并对比研究了两种缺陷对器件栅、漏延迟电流崩塌效应的影响.栅延迟测试表明,AlGaN表面坑状缺陷会引起栅延迟电流崩塌效应和源漏电阻的增加,而且表面坑状缺陷越多,栅延迟电流崩塌程度和源漏电阻的增加越明显.漏延迟测试显示,AlGaN表面坑状缺陷对漏延迟电流崩塌影响不大,而GaN缓冲层位错缺陷主要影响漏延迟电流崩塌.研究结果表明,AlGaN表面坑状缺陷和Ga关键词：AlGaN/GaN HEMT电流崩塌坑状缺陷位错缺陷     

AlGaN/GaN高电子迁移率晶体管中kink效应的半经验模型

初步分析了AlGaN/GaN 器件上的kink效应. 在直流模型的基础上, 建立了AlGaN/GaN 高电子迁移率晶体管中kink效应的半经验模型, 并加入了kink效应发生的漏源偏压与栅源偏压的关系. 该模型得出较为准确的模拟结果, 可用来判断kink效应的发生和电流的变化量. 最后, 我们采用模型仿真结合实验分析的方法, 对kink效应进行了一定的物理研究, 结果表明碰撞电离对kink效应的发生有一定的促进作用.     

AlGaN/GaN HEMT器件直流扫描电流崩塌机理及其物理模型

通过对AlGaN/GaN HEMT器件直流扫描情况下电流崩塌现象和机理的分析,建立了一个AlGaN/GaN HEMT器件的直流扫描电流崩塌模型.该模型从AlGaN/GaN器件工作机理出发,综合考虑了器件结构、半导体表面与界面,以及量子阱特殊结构对电流崩塌的影响.实验反复证明了该模型与实验结果有良好的一致性.关键词：AlGaN/GaN HEMT直流扫描电流崩塌模型     

AlGaN/GaN 高速电子迁移率晶体管器件电流坍塌效应与界面热阻和温度的研究

本文系统研究了AlGaN/GaN基高速电子迁移率晶体管器件界面热阻和工作温度对器件在高功率下的电流坍塌效应的影响规律.研究发现低漏极电压下热电子是导致负微分输出电导的重要因素,器件工作温度变高会使负微分输出电导减小.高漏极电压下自加热效应是导致电流坍塌的一个重要因素.随着界面热阻的增加,器件跨导降低,阈值电压增大.同时,由于工作环境温度的增高,器件随之温度增高,载流子迁移率会显著降低. 最终这两种因素会引起AlGaN/GaN基高速电子迁移率晶体管器件显著的电流坍塌效应,从而降低了器件整体性能.关键词：AlGaN/GaN HEMT 器件热电子效应自加热效应电流坍塌效应     

Kink effect in AlGaN/GaN high electron mobility transistors by electrical stress

The kink effect is studied in an AlGaN/GaN high electron mobility transistor by measuring DC performance during fresh, short-term stress and recovery cycle with negligible degradation. Vdg plays an assistant role in detrapping electrons and short-term stress results in no creation of new category traps but an increase in number of active traps. A possible mechanism is proposed that electrical stress supplies traps with the electric field for activation and when device is under test field-assisted hot-electrons result in electrons detrapping from traps, thus deteriorating the kink effect. In addition, experiments show that the impact ionization is at a relatively low level, which is not the dominant mechanism compared with trapping effect. We analyse the complicated link between the kink effect and stress bias through groups of electrical stress states: Vds = 0-state, off-state, on-state (on-state with low voltage, high-power state, high field state). Finlly, a conclusion is drawn that electric field brings about more severe kink effect than hot electrons. With the assistance of electric field, hot electrons tend to be possible to modulate the charges in deep-level trap.     

AIGaN／GaN高速电子迁移率晶体管器件电流坍塌效应与界面热阻和温度的研究

本文系统研究了A1GaN／GaN基高速电子迁移率晶体管器件界面热阻和工作温度对器件在高功率下的电流坍塌效应的影响规律．研究发现低漏极电压下热电子是导致负微分输出电导的重要因素,器件工作温度变高会使负微分输出电导减小．高漏极电压下自加热效应是导致电流坍塌的一个重要因素．随着界面热阻的增加,器件跨导降低,阂值电压增大．同时,由于工作环境温度的增高,器件随之温度增高,载流子迁移率会显著降低．最终这两种因素会引起A1GaN／GaN基高速电子迁移率晶体管器件显著的电流坍塌效应,从而降低了器件整体性能．     

中子辐照对AlGaN/GaN高电子迁移率晶体管器件电特性的影响

本文采用能量为1 MeV的中子对SiN钝化的AlGaN/GaN HEMT(高电子迁移率晶体管)器件进行了最高注量为1015cm-2的辐照.实验发现:当注量小于1014cm-2时,器件特性退化很小,其中栅电流有轻微变化(正向栅电流IF增加,反向栅电流IR减小),随着中子注量上升,IR迅速降低.而当注量达到1015cm-2时,在膝点电压附近,器件跨导有所下降.此外,中子辐照后,器件欧姆接触的方块电阻退化很小,而肖特基特性退化却相对明显.通过分析发现辐照在SiN钝化层中引入的感生缺陷引起了膝点电压附近漏电流和反向栅泄漏电流的减小.以上结果也表明,SiN钝化可以有效地抑制中子辐照感生表面态电荷,从而屏蔽了绝大部分的中子辐照影响.这也证明SiN钝化的AlGaN/GaN HEMT器件很适合在太空等需要抗位移损伤的环境中应用.     

AlGaN/GaN HEMTs grown on silicon (001) substrates by molecular beam epitaxy

We report the realization of an AlGaN/GaN HEMT on silicon (001) substrate with noticeably better transport and electrical characteristics than previously reported. The heterostructure has been grown by molecular beam epitaxy. The 2D electron gas formed at the AlGaN/GaN interface exhibits a sheet carrier density of 8×10¹² cm⁻² and a Hall mobility of 1800 cm²/V s at room temperature. High electron mobility transistors with a gate length of 4 μm have been processed and DC characteristics have been achieved. A maximum drain current of more than 500 mA/mm and a transconductance g_m of 120 mS/mm have been obtained. These results are promising and open the way for making efficient AlGaN/GaN HEMT devices on Si(001).     

场板结构AlGaN/GaN HEMT的电流崩塌机理

在不同的漏偏压下,研究了钝化和不同场板尺寸AlGaN/GaN HEMT对电流崩塌的抑制能力.实验结果表明,钝化器件对电流崩塌的抑制能力随着漏偏压的升高而显著下降;在高漏偏压下,场板的尺寸对器件抑制崩塌的能力有较大影响,而合适尺寸的场板结构在各个漏偏压下都能够很好的抑制电流崩塌.深入分析发现,场板结构不仅能够抑制虚栅的充电过程,而且提供了放电途径,有利于虚栅的放电,从而抑制电流崩塌.在此基础上,通过建立场板介质对虚栅放电的模型,解释了高漏偏压下场板的尺寸对器件抑制崩塌的能力有较大影响的原因.关键词：AlGaN/GaN HEMT场板电流崩塌     

场板结构AlGaN/GaN HEMT的电流崩塌机理

在不同的漏偏压下，研究了钝化和不同场板尺寸AlGaN/GaN HEMT对电流崩塌的抑制能力.实验结果表明，钝化器件对电流崩塌的抑制能力随着漏偏压的升高而显著下降；在高漏偏压下，场板的尺寸对器件抑制崩塌的能力有较大影响，而合适尺寸的场板结构在各个漏偏压下都能够很好的抑制电流崩塌.深入分析发现，场板结构不仅能够抑制虚栅的充电过程，而且提供了放电途径，有利于虚栅的放电，从而抑制电流崩塌.在此基础上，通过建立场板介质对虚栅放电的模型，解释了高漏偏压下场板的尺寸对器件抑制崩塌的能力有较大影响的原因.     

The physical process analysis of the capacitance-voltage characteristics of AlGaN/AlN/GaN high electron mobility transistors

This paper deduces the expression of the Schottky contact capacitance of AlGaN/AlN/GaN high electron mobility transistors (HEMTs), which will help to understand the electron depleting process. Some material parameters related with capacitance-voltage profiling are given in the expression. Detailed analysis of the forward-biased capacitance has been carried on. The gate capacitance of undoped AlGaN/AlN/GaN HEMT will fall under forward bias. If a rising profile is obviously observed, the donor-like impurity or trap is possibly introduced in the barrier.     

F离子注入新型Al0．25Ga0．75N／GaNHEMT器件耐压分析

为了缓解AlGaN／GaNhighelectronmobilitytransistors（HEMT）器件n型GaN缓冲层高的泄漏电流,本文提出了具有氟离子注入新型Al0．25Ga0．75N／GaNHEMT器件新结构．首先分析得出n型GaN缓冲层没有受主型陷阱时,器件输出特性为欧姆特性,这样就从理论和仿真方面解释了文献生长GaN缓冲层掺杂Fe,Mg等离子的原因．利用器件输出特性分别分析了栅边缘有和没有低掺杂漏极时,氟离子分别注入源区、栅极区域和漏区的情况,得出当氟离子注入源区时,形成的受主型陷阱能有效俘获源极发射的电子而减小GaN缓冲层的泄漏电流,击穿电压达到262v通过减小GaN缓冲层体泄漏电流,提高器件击穿电压,设计具有一定输出功率新型A1GaN／GaNHEMT提供了科学依据．     

Optimization of two-dimensional electron gases and – characteristics for AlGaN/GaN HEMT devices

In this paper, we take account of the spontaneous and piezoelectric polarization effect at the heterointerface in the AlGaN/GaN HEMT device, and one-dimensional Schrödinger–Poisson equations are solved self-consistently using a nonuniform mesh; using our findings, the AlGaN/GaN heterostructure conduction band and the two-dimensional electron gas (2DEG) density are investigated. The dependences of the 2DEG characteristics on the Al fraction, the thickness of each layer, the donor concentration and the gate voltage are investigated through simulation. The output characteristics are simulated using a quasi-2D model; a saturation voltage and threshold voltage are also shown. The influence of the spacer layer width on the 2DEG density is calculated for the first time. An explanation and analyses are given.     

高击穿电压的AlGaN/GaN FP-HEMT研究与分析

就蓝宝石衬底上制备的AlGaN/GaN场板(field plate)HEMT器件、常规HEMT器件性能进行了分析对比.结果证明两种结构的器件直流参数变化不大,但是采用场板后器件的击穿电压从52V提高到了142V.在此基础上利用Sivaco软件对两种器件进行模拟仿真,深入分析了FP对器件击穿电压的影响.