Room temperature NO_2 gas sensing of Au-loaded tungsten oxide nanowires/porous silicon hybrid structure

In this work, we report an enhanced nitrogen dioxide(NO_2) gas sensor based on tungsten oxide(WO_3)nanowires/porous silicon(PS) decorated with gold(Au) nanoparticles. Au-loaded WO_3 nanowires with diameters of 10 nm–25 nm and lengths of 300 nm–500 nm are fabricated by the sputtering method on a porous silicon substrate. The high-resolution transmission electron microscopy(HRTEM) micrographs show that Au nanoparticles are uniformly distributed on the surfaces of WO_3 nanowires. The effect of the Au nanoparticles on the NO_2-sensing performance of WO_3 nanowires/porous silicon is investigated over a low concentration range of 0.2 ppm–5 ppm of NO_2 at room temperature(25℃). It is found that the 10-? Au-loaded WO_3 nanowires/porous silicon-based sensor possesses the highest gas response characteristic. The underlying mechanism of the enhanced sensing properties of the Au-loaded WO_3 nanowires/porous silicon is also discussed.     

The light-enhanced NO₂ sensing properties of porous silicon gas sensors at room temperature

The NO2 gas sensing behavior of porous silicon(PS) is studied at room temperature with and without ultraviolet(UV) light radiation.The PS layer is fabricated by electrochemical etching in an HF-based solution on a p +-type silicon substrate.Then,Pt electrodes are deposited on the surface of the PS to obtain the PS gas sensor.The NO2 sensing properties of the PS with different porosities are investigated under UV light radiation at room temperature.The measurement results show that the PS gas sensor has a much higher response sensitivity and faster response-recovery characteristics than NO2 under the illumination.The sensitivity of the PS sample with the largest porosity to 1 ppm NO2 is 9.9 with UV light radiation,while it is 2.4 without UV light radiation.We find that the ability to absorb UV light is enhanced with the increase in porosity.The PS sample with the highest porosity has a larger change than the other samples.Therefore,the effect of UV radiation on the NO2 sensing properties of PS is closely related to the porosity.     

The light-enhanced NO2 sensing properties of porous silicon gas sensors at room temperature

The NO2 gas sensing behavior of porous silicon（PS） is studied at room temperature with and without ultraviolet（UV） light radiation.The PS layer is fabricated by electrochemical etching in an HF-based solution on a p ＋-type silicon substrate.Then,Pt electrodes are deposited on the surface of the PS to obtain the PS gas sensor.The NO2 sensing properties of the PS with different porosities are investigated under UV light radiation at room temperature.The measurement results show that the PS gas sensor has a much higher response sensitivity and faster response-recovery characteristics than NO2 under the illumination.The sensitivity of the PS sample with the largest porosity to 1 ppm NO2 is 9.9 with UV light radiation,while it is 2.4 without UV light radiation.We find that the ability to absorb UV light is enhanced with the increase in porosity.The PS sample with the highest porosity has a larger change than the other samples.Therefore,the effect of UV radiation on the NO2 sensing properties of PS is closely related to the porosity.     

Investigations on Pd:SnO2/porous silicon structures for sensing LPG and NO2 gas

P-type porous silicon (PS) structure has been prepared by anodic electrochemical etching process under optimized conditions. Photoluminescence studies of the PS structure show emission at longer wavelengths (red) for the excitation at 365 nm. Scanning electron microscope investigations of the PS surface confirm the formation of uniform porous structure, and the pore diameter have been estimated as 25 μm. Pd:SnO₂/PS/p-Si heterojunction with top gold ohmic contact developed by conventional methods has been used as the sensor device. Sensing properties of the device towards liquefied petroleum gas (LPG) and NO₂ gas have been investigated in an indigenously developed sensor test rig. The response and recovery characteristics of the sensor device at different operating temperatures show short response time for LPG. From the studies, maximum sensitivity and optimum operating temperature of the device towards LPG and NO₂ gas sensing has been estimated as 69% at 180 °C and 52% at 220 °C, respectively. The developed sensor device shows a short response time of 25 and 57 s for sensing LPG and NO₂ gases, respectively. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006.     

Growth of ZnO Nanostructures on Porous Silicon and Oxidized Porous Silicon Substrates

We have investigated an oxidation of substrate effect on structural morphology of zinc oxide (ZnO) rods. ZnO rods are grown on porous silicon (PS) and on thermally oxidized porous silicon substrates by carbothermal reduction of ZnO powder through chemical vapour transport and condensation. Porous silicon is fabricated by electrochemical etching of silicon in hydrofluoric acid solution. The effects of substrates on morphology and structure of ZnO nanostructures have been studied. The morphology of substrates is studied by atomic force microscopy in contact mode. The texture coefficient of each sample is calculated from X-ray diffraction data that demonstrate random orientation of ZnO rods on oxidized porous silicon substrate. The morphology of structures is investigated by scanning electron microscopy that confirms the surface roughness tends to increase the growth rate of ZnO rods on oxidized PS compared with porous silicon substrate. A green emission has been observed in ZnO structures grown on oxidized PS substrates by photoluminescence measurements.     

氧化钨纳米线气敏传感器的制备及其室温NO_2敏感特性

纳米结构的氧化钨有高比表面积和气体吸附能力,在气体传感器领域得到了广泛研究.本文采用磁控溅射金属钨薄膜和两步热氧化工艺在二氧化硅衬底上生长出氧化钨纳米线.通过改变第二步氧化温度,研究退火温度对氧化钨纳米线气敏特性的影响.采用扫描电子显微镜、X射线衍射仪、X射线光电子能谱分析仪和透射射电子显微镜表征材料的微观特性和晶体结构,利用静态配气法测试气敏性能.研究结果表明,经过退火处理后氧化钨纳米线密度略微降低,300℃比400℃退火后的氧化钨结晶性差,对应的表面态含量多,有利于室温气体敏感性.测试NO_2的气敏性能,经过对比得出300℃退火温度下制备的氧化钨纳米线在室温下表现出较很好的气敏响应,对6 ppm(1 ppm=10~(-6))NO_2达到2.5,对检测极限0.5 ppm NO_2响应达1.37.氧化钨纳米线在室温下表现出反常的P型响应,是因为氧化钨纳米线表面被氧气吸附形成反型层,空穴取代电子成为主要载流子所致.     

Chemical modification of porous and corrugated silicon surfaces in polyacrylic acid solutions

The chemical modification of porous silicon (PS) surfaces makes it possible to eliminate weak silicon-hydrogen bonds and prevent the formation of Si-O and Si-OH groups deep in pores and on a corrugated silicon surface. Hence, the effect of PS aging is not observed during its storage in air, and the porous layer??s composition is stable. Surfaces have been modified in polyacrylic acid solutions. The surface composition is analyzed on the basis of X-ray absorption spectra, and the morphology is investigated via scanning electron microscopy. It has been ascertained that the composition and morphology of a surface treated in polyacrylic acid solutions depend on the PS preparation method.     

Multiparametric sensor based on DBR porous silicon for detection of ethanol gas

We are here concerned with fabrication possibility of multiparametric gas sensor based on porous silicon. In order to use the porous silicon as a gas sensor, we made the DBR (distributed Bragg reflector) porous silicon onto silicon wafer and monitored the change of three parameters during exposure of DBR porous silicon to ethanol gas. The sensing parameters were the shift of reflectance peak, the PL (photoluminescence) intensity, and the electrical conductance. As a result, the spectra of reflectance and PL shifted toward longer wavelength. The electrical conductivity increases rapidly. After removing the gas, all sensing parameters return exactly to the initial value.     

High-resolution analytical electron microscopy of catalytically etched silicon nanowires

We report on the characterization of hexagonally ordered, vertically aligned silicon nanowires (SiNW) by means of analytical transmission electron microscopy. Combining colloidal lithography, plasma etching, and catalytic wet etching arrays of SiNW of a sub-50 nm diameter with an aspect ratio of up to 10 could be fabricated. Scanning transmission electron microscopy has been applied in order to investigate the morphology, the internal structure, and the composition of the catalytically etched SiNW. The analysis yielded a single-crystalline porous structure composed of crystalline silicon, amorphous silicon, and SiO _x with x≤2.     

Deposition and microstructure characterization of atmospheric plasma-sprayed ZnO coatings for NO2 detection

This work studied the possibility of using a sensor based on plasma-sprayed zinc oxide (ZnO) sensitive layer for NO₂ detection. The atmospheric plasma spray process was employed to deposit ZnO gas sensing layer and the obtained coating structure was characterized by scanning electron microscopy and X-ray diffraction analysis. The influences of gas concentration, working temperature, water vapor in testing air on NO₂ sensing performance of the ZnO sensors were studied. ZnO sensors showed a good sensor response and selectivity to NO₂ at an optimal working temperature.     

Fabrication of ZnO nanostructures of various dimensions using patterned substrates

ZnO nanostructures were grown on silicon, porous silicon, ZnO/Si and AlN/Si substrates by low-temperature aqueous synthesis method. The shape of nanostructures greatly depends on the underlying surface. Scattered ZnO nanorods were observed on silicon substrate, whereas aligned ZnO nanowires were obtained by introducing sputtered ZnO film as a seed layer. Furthermore, both the combination of nanorods and the bunch of nanowires were found on porous silicon substrates, whereas platelet-like morphology was observed on AlN/Si substrates. XRD patterns suggest the crystalline nature of aqueous-grown ZnO nanostructures and high-resolution transmission electron microscopy images confirm the single-crystalline growth of the ZnO nanorods along [0 0 1] direction. Room-temperature photoluminescence characterization clearly shows a band-edge luminescence along with a visible luminescence in the yellow spectral range.     

衬底对化学气相沉积法制备氧化硅纳米线的影响

通过化学气相沉积法在不同衬底上制备了大量的氧化硅纳米线.选用衬底为Si片、带有约100nm厚SiO2氧化层Si片和石英片.利用场发射扫描电子显微镜(SEM)和透射电镜(TEM，配备有能谱仪)对样品的表面形貌、结构和成分进行研究.结果表明：这些纳米线都为非晶态，但在不同衬底上生长的纳米线形貌、尺寸和化学成分不同.讨论了各种衬底对不同特征氧化硅纳米线生长的影响. 关键词： 化学气相沉积 纳米线 纳米颗粒     

Laser assisted chemical vapour deposition of silicon oxide layers

This paper focuses on the deposition of silicon oxide thin films, using laser assisted CVD based on a CO₂ laser, and on the feasibility of the process for coating porous silicon samples. Scanning electron and atomic force microscopy were used to analyse the morphology and microstructure of the films, while structure and chemical composition were determined by Fourier transform infrared and Rutherford backscattering spectroscopy. Two-wavelength ellipsometry was used for thickness and refractive index evaluation. The photoluminescence of SiO₂/PS was measured and compared with that of uncoated samples.     

少子寿命和表面形貌与多孔硅发光性能的关系

研究了不同时间腐蚀的多孔硅的光致发光性能与多孔硅的表面形貌和少子寿命之间的关系。结果表明,多孔硅的发光来自与氧空位有关的缺陷,而多孔硅表面的氢原子能够钝化多孔硅表面的非辐射中心从而提高多孔硅的发光效率。多孔硅的空隙度随腐蚀时间的延长而增大,这也导致了多孔硅的少子寿命的降低,从而造成多孔硅的光致发光效率随多孔硅空隙度的增大以及少子寿命的降低而提高。另外,原子力显微照片表明长时间的腐蚀使多孔硅表面层被化学腐蚀,从而降低了多孔硅表面的粗糙度。     

Preparation and room temperature NO_2-sensing performances of porous silicon/V_2O_5nanorods

In this paper, porous silicon/V₂O₅ nanorod composites are prepared by a heating process of as-sputtered V film on porous silicon (PS) at 600 ℃ for different times (15, 30, and 45 min) in air. The morphologies and crystal structures of the samples are investigated by field emission scanning electron microscope (FESEM), x-ray diffractometer (XRD), x-ray photoelectron spectroscopy (XPS), and Raman spectrum (RS). An improved understanding of the growth process of V₂O₅ nanorods on PS is presented. The gas sensing properties of samples are measured for NO₂ gas of 0.25 ppm～3 ppm at 25 ℃. We investigate the effects of the annealing time on the NO₂-sensing performances of the samples. The sample obtained at 600 ℃ for 30 min exhibits a very strong response and fast response-recovery rate to ppm level NO₂, indicating a p-type semiconducting behavior. The XPS analysis reveals that the heating process for 30 min produces the biggest number of oxygen vacancies in the nanorods, which is highly beneficial to gas sensing. The significant NO₂ sensing performance of the sample obtained at 600 ℃ for 30 min probably is due to the strong amplification effect of the heterojunction between PS and V₂O₅ and a large number of oxygen vacancies in the nanorods.     

Hydrothermal synthesis and gas sensing properties of variety low dimensional nanostructures of SnO2

New morphologies often play an important role in deciding the properties of nanomaterials. In current study, we synthesize various types of low dimensional SnO₂ nanostructure materials using a simple hydrothermal process. We find that the SnO₂ nanorods, nanowires and nanosheets show higher gas response as well as lower operating temperature as compared to that of nanospheres. In addition, the obtained nanosheets SnO₂ are found to show best sensing performances owing to the largest surface area and porous structure providing many quick passages to absorb and desorb gas, suggesting that the gas sensing properties of nanocrystals can be significantly improved by tailoring the shape and morphology of nanocrystals. Such an unexpected morphology holds substantial promise for rendering low dimensional nano-SnO₂ as a potential gas sensing material for future sensor application.     

n型有序多孔硅基氧化钨室温气敏性能研究

利用电化学腐蚀方法制备了n型有序多孔硅, 并以此为基底用直流磁控溅射法在其表面溅射不同厚度的氧化钨薄膜. 利用X射线和扫描电子显微镜表征了材料的成分和结构, 结果表明, 多孔硅的孔呈柱形有序分布, 溅射10 min的WO₃薄膜是多晶结构, 比较松散地覆盖在整个多孔硅的表面. 分别测试了多孔硅和多孔硅基氧化钨在室温条件下对二氧化氮的气敏性能, 结果表明, 相对于多孔硅, 多孔硅基氧化钨薄膜对二氧化氮的气敏性能显著提高. 对多孔硅基氧化钨复合结构的气敏机理分析认为, 多孔硅和氧化钨薄膜复合形成的异质结对良好的气敏性能起到主要作用, 氧化钨薄膜表面出现了反型层引起了气敏响应时电阻的异常变化. 关键词： 有序多孔硅 氧化钨薄膜 二氧化氮 室温气敏性能     

Characterization of nanostructured CuO–porous silicon matrix formed on copper-coated silicon substrate via electrochemical etching

A pulsed anodic etching method has been utilized for nanostructuring of a copper-coated p-type (100) silicon substrate, using HF-based solution as electrolyte. Scanning electron microscopy reveals the formation of a nanostructured matrix that consists of island-like textures with nanosize grains grown onto fiber-like columnar structures separated with etch pits of grooved porous structures. Spatial micro-Raman scattering analysis indicates that the island-like texture is composed of single-phase cupric oxide (CuO) nanocrystals, while the grooved porous structure is barely related to formation of porous silicon (PS). X-ray diffraction shows that both the grown CuO nanostructures and the etched silicon layer have the same preferred (220) orientation. Chemical composition obtained by means of X-ray photoelectron spectroscopic (XPS) analysis confirms the presence of the single-phase CuO on the surface of the patterned CuO–PS matrix. As compared to PS formed on the bare silicon substrate, the room-temperature photoluminescence (PL) from the CuO–PS matrix exhibits an additional weak ‘blue’ PL band as well as a blue shift in the PL band of PS (S-band). This has been revealed from XPS analysis to be associated with the enhancement in the SiO₂ content as well as formation of the carbonyl group on the surface in the case of the CuO–PS matrix.     

银纳米颗粒/多孔硅复合材料的制备与气敏性能研究

采用双槽电化学腐蚀法以电阻率为10-15 Ω·cm的p型<100>晶向的单晶硅片制备了孔径约为1.5 μm, 孔深约为15-20 μm的p型多孔硅, 并以此多孔硅作为基底采用无电沉积法通过调控沉积时间在其表面沉积了不同厚度的银纳米颗粒薄膜. 采用扫描电子显微镜和X 射线衍射仪表征了银纳米颗粒/多孔硅复合材料的形貌和微观结构, 结果表明银纳米颗粒较均匀的分布于多孔硅的表面上且沉积时间对产物的形貌有重要影响. 采用静态配气法在室温下研究了银纳米颗粒/多孔硅复合材料对NH₃的气敏性能. 气敏测试结果表明沉积时间对产物的气敏性能影响较大. 当沉积时间较短时, 适量银纳米颗粒掺杂的多孔硅复合材料由于其较高的比表面积以及特殊的形貌和结构, 对NH₃气体表现出较高的灵敏度、优良的响应/恢复性能. 室温下, 其对50 ppm 的NH₃气体的气敏灵敏度可以达到5.8左右.     

TEM characterisation of porous silicon

In this work, the results of a structural investigation by transmission electron microscopy of porous silicon and porous silicon-based devices is reported. This investigation covers a wide range of porous silicon materials going from photoluminescent micro- or meso-porous silicon to macro-porous layers as well as some recent applications of this material for the fabrication of porous silicon and Si/SiO2 superlattices, suspended thick membranes and gas sensor devices. It appears that the structural investigation technique here employed, is a fundamental tool for the optimisation of the technological processing of this material. From the results reported in this work, a quite comprehensive view of the potentialities and limitations of the applications of porous silicon in the field of optical and gas sensor devices should also emerge. Finally, some solutions to the problems usually met during the technological processing of this material are proposed.