o-Dianisidine: a new reagent for selective spectrophotometric, flow injection determination of chlorine.

A flow injection analysis (FIA) procedure for the determination of free chlorine in industrial formulations and water samples is proposed. The manifold is provided with a gas-diffusion unit which permits the removal of interfering species and also the preconcentration of chlorine. The determination of chlorine is performed on the basis of the oxidation by o-dianisidine as a chromogenic reagent to a coloured product which can be monitored at 445 nm. The method (for a preconcentration step of 60 s) is linear over the range 0.04-1.00 mg l(-1) of chlorine, the limit of detection is 0.04 mg l(-1), the reproducibility of the procedure (as RSD of the slope) is 3.7% for a series of four independent calibrations, the precision (as RSD of a series of 30 continuous FIA peaks of 0.56 mg l(-1) of chlorine) is 1.4% and the sample throughput is 40 h(-1). A detailed comparative study of the analytical characteristics of a single mono-channel reverse FIA assembly and the same system but provided with a Fluoropore membrane filter of 0.5 microm pore size was performed to check the advantages of the new approach in terms of sensitivity, selectivity and limit of detection.     

Flow injection turbidimetric determination of thiamine in pharmaceutical formulations using silicotungstic acid as precipitant reagent

A simple flow injection system is proposed for the determination of thiamine in pharmaceutical formulations. The determination is based on the precipitation reaction of thiamine with silicotungstic acid in acidic medium to form a thiamine silicotungstate suspension that is measured at 420 nm. Adding 0.05% (w/v) poly(ethyleneglycol) in the carrier solution (0.5 mol l(-1) hydrochloric acid), an improvement in the sensitivity, repeatability and baseline stability of the flow injection system was obtained. The calibration graph was linear in the thiamine concentration range from 5.0x10(-5) to 3.0x10(-4) mol l(-1) with a detection limit of 1.0x10(-5) mol l(-1). The relative standard deviations for ten successive measurements of 1.0x10(-4) mol l(-1) and 2.5x10(-4) mol l(-1) thiamine were less than 1% and an analytical frequency of 90 h(-1) was obtained.     

Electrochemical determination of minoxidil in different pharmaceutical formulations by flow injection analysis.

The electrochemical behavior and amperometric-FIA quantification of minoxidil at a glassy carbon electrode is described. The procedure is based on electrochemical oxidation at 0.800 V (vs. Ag/AgCl/NaCl(3 M) in a phosphate buffer solution. Minoxidil was determined over the range 1 x 10(-7) - 1 x 10(-4) M. Different analytical parameters and electrode stability were analyzed to obtain the best electrode performance. The optimal conditions were: working potentials, 0.800 V; flow rate, 0.74 mL min(-1); and solution pH 7.0. This system allowed a sampling rate of 120 samples per hour without any pretreatment. The proposed method was used for minoxidil quantification in pharmaceutical preparations with satisfactory results. The accuracy of FIA-amperometric method was established by a comparison with the conventional UV determination technique using a paired t-test indicating the absence of systematic errors.     

Flow-injection spectrophotometric determination of methyldopa in pharmaceutical formulations

A flow-injection spectrophotometric procedure is proposed for methyldopa determination in pharmaceutical preparations. The determination is based on formation of a yellow product (measured at 410 nm) after complexation of methyldopa with molybdate. Under optimal conditions, Beer's law is obeyed in a concentration range of 50-200 mg l⁻¹ methyldopa. Typical correlation between absorbance and analyte concentration was 0.9999. Usual excipients used as additives in pharmaceuticals do not interfere with the proposed method. The analytical frequency was 210 h⁻¹ and the relative standard deviation (R.S.D.) was ≤2% for sample solution containing 150 mg l⁻¹ methyldopa (n = 11). The analytical results obtained in commercial formulations by applying the proposed FIA method were in good agreement with labeled values and those obtained by the Brazilian Pharmacopoeia procedure at 95% confidence level.     

Cost-effective flow injection spectrophotometric assay of iron content in pharmaceutical preparations using salicylate reagent

A new flow injection procedure for an assay of Fe(III) by using salicylate obtained from antipyretic powder, which is a cheap and easily available reagent, is proposed. A red complex was continuously monitored by a laboratory-made green LED colorimeter. A linear calibration was obtained in the range of 1–20 mg Fe l⁻¹ with a detection limit of 0.5 mg Fe l⁻¹ and R.S.D.s of 1.4–5.4% (n=3, for 1–20 mg Fe l⁻¹). The new procedure was applied to assay iron contents in pharmaceutical preparations. The results were in good agreement with those of the USP standard method.     

The spectrophotometric determination of hydroperoxide and peroxide in a lipid pharmaceutical product by flow injection analysis

A sensitive, rapid and automatable flow injection analysis procedure is described for the determination of total hydroperoxides and peroxides in lipid products. All unsaturated lipids are susceptible to degradation by oxidation, and the quantification of these major oxidation products is an essential measure of lipid product stability. In this methodology a lipid emulsion is dispersed and injected into an acidic solution of propan-2-ol, which is then merged with iodide ion in situ in a two-stream manifold. The lipid hydroperoxide oxidises acidified iodide to iodine, which is detected spectrophotometrically at 350 nm. The closed conditions prevent interference from atmospheric oxygen and the short reaction time minimises interference from side reactions. Conditions were optimised, using experimental design, for a lipid product under development at GlaxoWellcome. A two-level half-fractional factorial design was applied to screen for the critical factors, followed by a multi-level central composite design to optimise these variables. The resulting method was fully validated and is linear down to 0.1 nmol ml-1. This approach should be applicable to other lipid formulations and offers significant advantages in terms of speed, automation and precision compared with existing manual procedures.     

Four spectrophotometric methods for determination of nitrofurazone in pharmaceutical formulations

Four simple and sensitive visible spectrophotometric methods (A-D) for the determination of nitrofurazone in bulk samples and pharmaceutical formulations are described. They are based on the formation of colored species by treating either its reduction product with 3-methylbenzothiazolin-2-one hydrazone in the presence of ferric chloride (method A: _max 600 nm) or its hydrolysis product with thiobarbituric acid (method B: _max 520 nm, 440 nm) or barbituric acid (method C: _max 400 nm) or by oxidizing it with excess N-bromosuccinimide and determining the consumed NBS using metol-isonicotinic acid hydrazide (method D: _max 620 nm).     

Reverse flow injection spectrophotometric determination of iron(III) using chlortetracycline reagent

A simple reversed flow injection colourimetric procedure for determining iron(III) was proposed. It is based on the reaction between iron(III) with chlortetracycline, resulting in an intense yellow complex with a suitable absorption at 435 nm. A 200 μl chlortetracycline reagent solution was injected into the phosphate buffer stream (flow rate 2.0 ml min⁻¹) which was then merged with iron(III) standard or sample in dilute nitric acid stream (flow rate 1.5 ml min⁻¹). Optimum conditions for determining iron(III) were investigated by univariate method. Under the optimum conditions, a linear calibration graph was obtained over the range 0.5–20.0 μg ml⁻¹. The detection limit (3σ) and the quantification limit (10σ) were 0.10 and 0.82 μg ml⁻¹, respectively. The relatives standard deviation of the proposed method calculated from 12 replicate injections of 2.0 and 10.0 μg ml⁻¹ iron(III) were 0.43 and 0.59%, respectively. The sample throughput was 60 h⁻¹. The proposed method has been satisfactorily applied to the determination of iron(III) in natural waters.     

Determination of lithium in pharmaceutical formulations used in the treatment of bipolar disorder by flow injection analysis with spectrophotometric detection

In this work, a flow injection system with spectrophotometric detection was developed for the determination of lithium in pharmaceutical formulations used in the treatment of bipolar disorder. Reaction between Quinizarine (1,4-dihydroxyanthraquinone) and Li(I) ion in alkaline medium containing dimethylsulfoxide (DMSO) was explored for this purpose. The flow system was optimized regarding to its chemical (DMSO, Quinizarine and NaOH concentrations and sample pH) and physical parameters (sample loop volume, carrier flow rate and reactor length) in order to establish better conditions in terms of sensitivity and sampling frequency. The results obtained showed that the concentration of DMSO in the reagent solution presents remarkable influence on the magnitude of analytical signal. Chemical species that could be found in the formulations such as Na(I), K(I), Mg(II), Ca(II), Ti(IV), Cl⁻, CO₃²⁻ e sodium dodecylsulfate were tested as possible interfering ions. Among them, only non-monovalent cations presented noticeable interference on lithium signal. However, they were not found in concentrations high enough to cause interference in the determination of lithium in the samples. Sample preparation was performed by sonicating a slurry prepared by dispersing 100 mg of powdered sample in 15 mL of 0.10 mol L⁻¹ HCl solution. Results obtained by developed methodology were not statistically different from those obtained by flame emission spectrometry. In the optimized conditions the method presented a linear range of 5-40 mg L⁻¹ and a relative standard deviation of 3.6% at 5 mg L⁻¹ Li concentration. Detection and quantification limits were 0.54 and 1.8 mg L⁻¹, respectively. Sampling frequency, calculated as the time interval passed between two consecutive injections, was 60 samples per hour. The methodology was successfully applied in the determination of lithium in three commercial samples.     

Use of microemulsions in flow injection analysis: spectrophotometric determination of copper

The use of microemulsions as media for liquid/liquid extraction is considered, with particular reference to the copper(II)/2,9-dimethyl-1,10-phenanthroline complex. Aqueous copper(II) standards covering the range 2.5 × 10^?5–7.5 × 10^?3 M were determined by a batch extraction procedure and by three flow-injection extraction procedures, one based on a pre-made water in oil microemulsion, one on a water in oil microemulsion formed on-line and one on an oil in water microemulsion.     

Simultaneous spectrophotometric determination of uranium and thorium by flow injection analysis using selective masking.

A flow injection system for the simultaneous determination of uranium and thorium has been developed by using selective masking and a spectrophotometric detector with two flow cells aligned with the same optical path. The injected sample solution was first mixed with a reagent solution containing Chromazurol S (CAS) and cetyltrimethylammonium chloride (CTMAC), and the total absorbance of uranium- and thorium-CAS complexes was measured in the first flow cell at 620 nm. The sample stream was then mixed with an EDTA solution in order to convert the thorium-CAS complex to a thorium-EDTA complex, and the absorbance of the uranium-CAS complex was measured in the second flow cell. The detection limits were 10 microg dm(-3) for uranium and 7 microg dm(-3) for thorium. The calibration graphs were linear (r < 0.9998) at least over the ranges of 0.1 to 10 mg dm(-3) for uranium and 0.08 to 8 mg dm(-3) for thorium. The RSDs were less than 1.5% (n = 3) in the calibration range. Uranium and thorium of up to the 6-fold concentration to each other could be determined in admixtures with relative errors of less than 3.3%. The sample throughput was 24 per hour. The proposed system was successfully applied to the analysis of a uranium-thorium ore mock solution by coupling with anion-exchange in a magnesium nitrate medium to eliminate interference from coexisting elements.     

Flow injection manifold for the direct spectrophotometric determination of bismuth in pharmaceutical products using Methylthymol Blue as a chromogenic reagent

A new simple and rapid flow injection method is reported for the direct determination of bismuth in pharmaceutical products. Methylthymol Blue (MTB) was used as a chromogenic reagent and the absorbance of the colored Bi(III)-MTB complex produced was monitored at 548 nm. The various chemical and physical variables were optimized and a study of interfering ions was also carried out. Linear calibration graphs were obtained from 0 to 100 mg l-1 Bi(m) (120 injections per hour). The precision was very good (sr = 1.3%) and the limit of detection was cL = 0.150 mg l-1. The average accuracy was also very good (er = 0.75%) and was evaluated by comparison of the results obtained with those claimed by the manufacturers. The method was found to be adequately selective, considering the ions that the samples contain.     

Enzymatic determination of vitamin A in pharmaceutical formulations with spectrophotometric detection

An enzymatic method for the determination vitamin A (retinol) is reported using soluble and immobilized alcohol dehydrogenase, isolated from rabbit liver. The reaction is based on the oxidation of retinol and simultaneous reduction of NAD⁺ to NADH followed by spectrophotometric detection at 340 nm. The calibration graph was linear over the range of 2.0–10 μM with correlation coefficients of 0.9967 and 0.9992 (n = 5) for soluble and immobilized alcohol dehydrogenase respectively, with relative standard deviations (n = 3) in the range of 0.5–1.2%. The limit of detection was lower than 1.0 μM. The proposed method was applied to determine vitamin A in pharmaceuticals, and the results obtained were in reasonable agreement with the amount labeled. The results were compared using spectrophotometric reference method, and no significant difference was found between the results of the both methods.     

Flow-injection turbidimetric determination of homatropine methylbromide in pharmaceutical formulations using silicotungstic acid as precipitant reagent

A flow-injection turbidimetric procedure exploiting merging zones is proposed for determining homatropine methylbromide (HMB) in pharmaceutical preparations. The determination is based on the precipitation reaction of homatropine methylbromide with silicotungstic acid in acidic medium to form a precipitate, which was measured at 410 nm. The analytical curve was linear in the HMB concentration range from 8.1 × 10⁻⁵ to 2.2 × 10⁻⁴ mol l⁻¹, with a detection limit of 5.0 × 10⁻⁶ mol l⁻¹. The recoveries ranged from 96 to 103%, the sampling frequency was 70 determinations per hour and relative standard deviations were less than 1.5% (n = 10). The results obtained for commercial formulations using the FIA procedure were in good agreement with those obtained by using a comparative method.     

流动注射光度法直接测定海水中的微量苯胺

基于苯胺与亚硝酸盐的重氮化反应及反应产物与甲萘酚的显色,借助流动分析技术,实现了海水中苯胺含量的分析测定。体系以30.9g/L的NaCl做载液、人工海水配制标准样品,对各个影响因素进行了优化。苯胺浓度在0.01～1.0mg/L范围内与相对峰高呈线性关系,线性方程ΔH(mV)=200.53ρ+1.0728(n=8,ρ为苯胺浓度mg/L),相关系数R2=0.9982。方法的检出限(3σ)为0.005mg/L,相对标准偏差(RSD)为4.8%(n=11)。考察了共存离子、不同盐度样品对分析测定的影响。用于实际海水样品的分析,回收率为95.8%～106.6%。     

Flow injection spectrophotometric determination of anionic surfactants using methyl orange as chromogenic reagent

A flow injection(FI) spectrophotometric method for the determination of anionic surfactants was developed on the basis of the competition for the cationic surfactant cetyl pyridine (CP+) chloride between the acidic dye methyl orange (MO) and anionic surfactants. In a pH 5.0 medium the cation of cetyl pyridine (CP+) reacts with dissociated methyl orange (MO-) to form an ion-associate complex, causing a blue shift of lambda(max) from 465 nm for MO- to 358 nm for the CP+ x MO- associate. The MO- in the ion-associate complex can be quantitatively substituted by such anionic surfactants as sodium dodecyl benzene sulfonate (DBS) or sodium lauryl sulfate (LS), leading to an increase in the absorbance measured at 465 nm. This increased absorbance value is proportional to the concentration of anionic surfactants. Various chemical and physical parameters for the FI spectrophotometric method were optimized, and interference-free levels were examined. At the optimized conditions, Beer's law was obeyed in the range 1.4 approximately 25 mg/L sodium DBS for an injected sample volume of 180 microL, and a detection limit of 0.22 mg/L for sodium DBS was achieved at a sampling rate of 90 h(-1). Eleven determinations of a 16 mg/L sodium DBS solution gave a RSD of 0.4%. The proposed method has successfully been applied to the determination of anionic surfactant concentration in waste water and in detergents.     

A simple flow injection spectrophotometric procedure for the determination of diazepam in pharmaceutical formulation.

A single-channel flow injection (FI) manifold with spectrophotometric detection has been designed and fabricated for diazepam determination. A 100 microl sample and/or standard solution containing diazepam was injected into a flowing stream of 0.1 mol L(-1) hydrochloric acid with the optimum flow rate of 6.8 mL min(-1). As soon as the sample reached the detector, the FI signal as a peak was recorded at 360 nm. The optimum conditions for microg amounts of diazepam were achieved. A linear calibration graph over the range of 2-110 mg L(-1) diazepam was obtained with the regression equation Y = 0.2926X + 0.5896 (r2 = 0.9929). The method was very sensitive, since as little as 0.60 mg L(-1) could be detected; very reproducible with an RSD of 3.3% (n=11); and very rapid with a sampling rate of 100 h(-1). The limit of quantitation (10 sigma) was 2.0 mg L(-1). The proposed FI procedure has been satisfactorily applied to the quantitation of diazepam in commercial pharmaceutical formulations. The obtained results were in excellent agreement with those obtained by the conventional spectrophotometric method, verified by the student t-test at the 95% confidence level.     

Indirect spectrophotometric determination of diltiazem hydrochloride in pure form and pharmaceutical formulations

Three simple, accurate, and sensitive spectrophotometric methods (A, B and C) have been described for the indirect assay of diltiazem hydrochloride (DIL.HCl), either in pure form or in pharmaceutical formulations. The first method (A) is based on the oxidation of DIL.HCl by N-bromosuccinimide (NBS) and determination of unconsumed NBS by measuring the decrease in absorbance of amaranth dye (AM) at a suitable λ _max =521 nm. Other methods (B) and (C) involve the addition of excess cerric ammonium sulfate (CAS) and subsequent determination of the unconsumed oxidant by a decrease in the red color of chromotrope 2R (C2R) at a suitable λ _max =528 nm or a decrease in the orange-pink color of rhodamine 6G (Rh6G) at λ _max =525 nm, respectively. Regression analysis of Beer-Lambert plots showed good correlation in the concentration ranges 3.0–9.0, 3.5–7.0 and 3.5–6.3 μg ml⁻¹ for methods A, B and C, respectively. The apparent molar absorptivity, Sandell's sensitivity, detection and quantification limits were calculated. The proposed methods have been applied successfully for the analysis of the drug in its pure form and its dosage form. No interference was observed from a common pharmaceutical adjuvant. Statistical comparison of the results with the reference method shows excellent agreement and indicates no significant difference in accuracy and precision.     

Sequential injection spectrophotometric determination of phenylephrine hydrochloride in pharmaceutical preparations

A fully automated sequential injection spectrophotometric method for the determination of phenylephrine hydrochloride in pharmaceutical preparations is reported. The method is based on the condensation reaction of the analyte with 4-aminoantipyrine in the presence of potassium ferricyanide. The absorbance of the condensation product was monitored at 503 nm. A linear relationship between the relative peak height and concentration was obtained in the range 0.5-17.5 mg l⁻¹. The detection limit (as 3σ value) was 0.09 mg l⁻¹ and repeatability was 0.8 and 0.6% at 2.5 and 5 mg l⁻¹, respectively. Results obtained by this method agreed very well with those obtained by the AOAC official method.