用光电子能谱研究CdTe太阳电池的背接触特性

CdTe太阳电池的背电极须采用高功函数金属。通过采用光电子能谱(XPS)分析了高功函数金属Au和Ni分别作为背电极的CdTe太阳电池背接触特性,发现在背电极剥离后,Au在ZnTe/ZnTe∶Cu背接触层表面以Au单质形式存在,扩散深度较浅;Ni扩散到ZnTe/ZnTe∶Cu复合层的深度比Au大,且大多呈离子态,与ZnTe/ZnTe∶Cu复合层中的富Te离子形成Ni_xTe,提高了掺杂浓度,使电池性能获得改善。在两样品中还发现,不论是Te的峰还是Zn的峰,其峰的位移变化都很小,说明两样品中Te和Zn的存在形式没有发生变化。     

CdTe太阳电池的不同背电极和背接触层的特性研究

用Ni替代Au来作为CdTe太阳电池的背电极，比较了Ni,Ni/Au,Au/Ni及Au背电极对电池性能的影响.发现Ni作为背电极和ZnTe/ZnTe:Cu复合层接触，电池的开路电压V_oc略有降低，填充因子FF有增有减，变化幅度不大，但因短路电流I_sc有较大的提高，转换效率η平均增长4％.测试了不同背电极的CdTe太阳电池的暗I-V和C-V特性，对背电极剥离后的样品进行了XPS测试分析.结果表明，Ni扩散到ZnTe/ZnTe:Cu复合层的深度比Au多，且大多呈离子态，与ZnTe/ZnTe:Cu复合层中的富Te离子形成Ni_xTe，提高了掺杂浓度，使电池性能获得改善. 关键词： 金属背电极 复合背接触层 转换效率 CdTe太阳电池     

稀土掺杂CdTe太阳电池背接触层ZnTe的第一性原理研究

结合CdS/CdTe太阳电池背接触层的制备要求考虑, 利用基于密度泛函理论平面波超软赝势方法和广义梯度近似, 计算了未掺杂ZnTe、稀土Y、Gd掺杂ZnTe的能带和电子态密度, 得到了不同体系下系统总能和晶格常数. 研究表明, 稀土Y和Gd掺杂后ZnTe结构的稳定性均提高, 掺杂Y使ZnTe与CdTe的晶格匹配更好. 计算表明, 掺杂可使载流子发生简并, 掺Y比掺Gd电子有效质量小, 掺Y与掺Gd的载流子浓度数量级相同. 根据计算结果分析了稀土掺杂对ZnTe背接触层的影响. 关键词： ZnTe 稀土掺杂 第一性原理 太阳电池背接触层     

CdTe太阳电池背接触层的XPS研究

采用共蒸发法在不同条件下制备了ZnTe和ZnTe∶Cu多晶薄膜,通过XRD和XPS研究了它们的结构和各元素的浓度分布。结果表明,不同衬底温度下沉积的薄膜,结构无明显变化,利用XPS溅射剖析获得了薄膜中各成分浓度随溅射时间变化的分布图,发现不同条件下制备的薄膜,溅射速率不同,各成分随溅射时间的变化也不相同。薄膜中Cu的浓度随溅射时间增加而快速增加,并达到一极大值,然后快速下降。根据Cu浓度的变化研究了ZnTe层对Cu原子的阻挡作用,通过对Cu浓度随时间变化分布图的比较,作者认为,用70 ℃制备ZnTe,而后在常温下制备ZnTe∶Cu的复合膜作为CdTe太阳电池的背接触层,能有效阻挡Cu原子的扩散,提高电池效率。     

新型硒化锑薄膜太阳电池背接触优化

硒化锑(Sb₂Se₃)具有低毒、原材料丰富和光电性能优异等优点,被认为是最具有发展潜力的薄膜太阳电池光吸收层材料之一.但目前Sb₂Se₃薄膜太阳电池光电转换效率与碲化镉、铜铟镓硒和钙钛矿等太阳电池相比仍存在较大差距.限制Sb₂Se₃薄膜太阳电池光电转换效率进一步提升的关键因素之一是,太阳电池结构中Mo背电极和Sb₂Se₃薄膜构建的背接触界面处容易形成较高的势垒,降低载流子的抽取效率.本工作则对Mo背电极进行热处理生成缓冲层MoO₂薄膜,发现缓冲层MoO₂的引入,可有效地促进Sb₂Se₃薄膜的择优取向生长,同时实现太阳电池Mo/MoO2/Sb₂Se₃背接触势垒降低,相应的填充因子、开路电压和短路电流密度均获得显著提高,构建的太阳电池光电转换效率从5.04%提升至7.05%.     

基于氧化镍背接触缓冲层碲化镉薄膜太阳电池的研究

采用电子束蒸发法制备了NiO薄膜,并对其作为碲化镉薄膜太阳电池背接触缓冲层材料进行了相关研究.NiO缓冲层的加入使得碲化镉太阳电池开路电压显著增大.通过X射线光电子能谱测试得到的NiO/CdTe界面能带图表明NiO和CdTe的能带匹配度很好.NiO是宽禁带P型半导体材料,在电池背接触处形成背场,减少了电子在背表面处的复合,从而提高电池开路电压.通过优化NiO薄膜厚度,制备得到转换效率为12.2%、开路电压为789 mV的碲化镉太阳电池.研究证实NiO是用来制备高转换效率、高稳定性碲化镉薄膜太阳电池的一种极有前景的缓冲层材料.     

CdS/CdTe薄膜太阳电池的深能级瞬态谱和光致发光研究

用深能级瞬态谱和光致发光研究了无背接触层的CdS/CdTe薄膜太阳电池的杂质分布和深能级中心.得到了净掺杂浓度在器件中的分布.确定了两个能级位置分别在E_V+0365 eV和E_V+0282 eV的深中心,它们的浓度分别为167×10¹² cm^-3和386×10¹¹ cm^-2,俘获截面分别为143×10^-14cm²和153×10^-16cm².它们来源于以化学杂质形式存在的Au和（或）Te_Cd^-复合体,或与氩氧气氛下沉积CdTe时的氧原子相关. 关键词： 深能级瞬态谱 光致发光 CdS/CdTe太阳电池     

不同温度下制备的CdTe薄膜对太阳电池光电性能的影响

在不同温度下用近空间升华法（CSS）制备了CdTe多晶薄膜,结合I-V,C-V特性及深能级瞬态谱研究了不同温度制备的CdTe薄膜对CdS/CdTe太阳电池性能的影响.结果表明,制备温度对电池组件的开路电压影响不大,对短路电流和填充因子有影响,CdTe薄膜的深中心对温度和频率的响应基本一致.580℃制备的样品暗饱和电流密度最小,载流子浓度较高,光电特性较好,而且空穴陷阱浓度较低,深中心复合作用较小.在此研究基础上制备出了面积为300 mm×400 mm 关键词： 制备温度 CdTe薄膜 深能级瞬态谱（DLTS） CdS/CdTe太阳电池     

具有高阻抗本征SnO2过渡层的CdS/CdTe多晶薄膜太阳电池

采用超声喷雾热解法制备了具有高阻抗的本征SnO2透明导电膜,将其运用在CdS层减薄了的CdS/CdTe多晶薄膜太阳电池中,对减薄后的CdS薄膜进行了XRD,AFM图谱分析,并对电池进行了光、暗I-V,光谱响应和C-V测试.结果表明,在高阻膜上沉积的减薄CdS薄膜(111)取向更明显,但易形成微孔.引入高阻层后,能消除CdS微孔形成的微小漏电通道,有效保护p-n结,改善了电池的并联电阻、填充因子和短波响应,使载流子浓度增加,暗饱和电流密度减小,从而电池性能得到改善,电池转换效率增加了14.4%.     

具有高阻抗本征SnO2过渡层的CdS/CdTe多晶薄膜太阳电池

采用超声喷雾热解法制备了具有高阻抗的本征SnO₂透明导电膜，将其运用在CdS层减薄了的CdS/CdTe多晶薄膜太阳电池中，对减薄后的CdS薄膜进行了XRD,AFM图谱分析，并对电池进行了光、暗I-V，光谱响应和C-V测试.结果表明，在高阻膜上沉积的减薄CdS薄膜(111)取向更明显，但易形成微孔.引入高阻层后，能消除CdS微孔形成的微小漏电通道，有效保护p-n结，改善了电池的并联电阻、填充因子和短波响应，使载流子浓度增加，暗饱和电流密度减小，从而电池性能得到改善，电池转换效率增加了14.4%. 关键词： CdTe电池 过渡层 效率     

碲化镉薄膜太阳电池中的关键科学问题研究

文章对CdTe薄膜太阳电池中的4个关键科学问题进行了讨论,并对电池器件的性能进行了研究,其中包括高质量硫化镉薄膜、背接触层、CdS/CdTe界面和CdCl2热处理性能的研究。文章作者研究了背电极接触层中Cu掺杂含量对电池性能的影响,通过改变背接触层中Cu的含量,可以改变Cu与Te反应产生的物相成分,从而发现以Cu1.4Te为主导的背接触缓冲层能有效地减少电池I—V 曲线中的“翻转”(roll-over)现象,同时能有效地降低背接触势垒。此外,还研究了CdS/CdTe界面的CdCl2热处理反应,发现当热处理温度高于350℃时,CdS与CdTe之间的互扩散开始发生,此温度对应于CdS由立方相转变为六方相;而在550℃热处理后,S 和Te 互扩散形成的CdSxTe1-x 化合物,其x 值高达11%。通过优化电池制备工艺,获得了在AM1.5标准光源下高达14.6%的CdTe电池转换效率。     

Deep level transient spectroscopy investigation of deep levels in CdS/CdTe thin film solar cells with Te:Cu back contact

Deep levels in Cds/CdTe thin film solar cells have a potent influence on the electrical property of these devices. As an essential layer in the solar cell device structure, back contact is believed to induce some deep defects in the CdTe thin film. With the help of deep level transient spectroscopy (DLTS), we study the deep levels in CdS/CdTe thin film solar cells with Te:Cu back contact. One hole trap and one electron trap are observed. The hole trap H1, localized at E_v+0.128~eV, originates from the vacancy of Cd (V_Cd. The electron trap E1, found at E_c-0.178~eV, is considered to be correlated with the interstitial Cu_i⁼ in CdTe.     

Short-circuit current improvement in CdTe solar cells by combining a ZnO buffer layer and a solution back contact

Conventional CdTe solar cells have a CdS window layer, in which an absorption loss of photons with more than 2.4 eV occurs through the CdS layer. A thinner CdS layer was applied to enhance light transmission and a ZnO buffer layer with a band gap of 3.3 eV was introduced to suppress shunting through the thinner CdS window layer. A 100-nm thick ZnO layer sputter-deposited at 300 °C had uniform coverage on a transparent conductive oxide (TCO) after a subsequent high-temperature process. The ZnO layer was effective in preventing shunting through the CdS window layer so that the open-circuit voltage and fill factor of the CdTe solar cells were recovered and the short-circuit current was enhanced over that of the conventional CdTe solar cell. In the ZnO/CdS/CdTe configuration, the short-circuit current was further improved throughout the visible wavelength region by replacing the Cu-metal contact with a Cu solution contact. As a result the short-circuit current from 21.7 to 26.1 mA/cm² and the conversion efficiency of the CdTe solar cell increased from 12 to 15% without antireflective coating. Our result indicates that the Cu solution back contact is a critical factor for achieving a higher cell efficiency in addition to ZnO buffer layer.     

Recombination-induced voltage-dependent photocurrent collection loss in CdTe thin film solar cell

Recently, the efficiency of CdTe thin film solar cell has been improved by using new type of window layer Mg_xZn_1-xO (MZO). However, it is hard to achieve such a high efficiency as expected. In this report a comparative study is carried out between the MZO/CdTe and CdS/CdTe solar cells to investigate the factors affecting the device performance of MZO/CdTe solar cells. The efficiency loss quantified by voltage-dependent photocurrent collection efficiency (η_C(V')) is 3.89% for MZO/CdTe and 1.53% for CdS/CdTe solar cells. The higher efficiency loss for the MZO/CdTe solar cell is induced by more severe carrier recombination at the MZO/CdTe p—n junction interface and in CdTe bulk region than that for the CdS/CdTe solar cell. Activation energy (E_a) of the reverse saturation current of the MZO/CdTe and CdS/CdTe solar cells are found to be 1.08 eV and 1.36 eV, respectively. These values indicate that for the CdS/CdTe solar cell the carrier recombination is dominated by bulk Shockley—Read—Hall (SRH) recombination and for the MZO/CdTe solar cell the carrier recombination is dominated by the p—n junction interface recombination. It is found that the tunneling-enhanced interface recombination is also involved in carrier recombination in the MZO/CdTe solar cell. This work demonstrates the poor device performance of the MZO/CdTe solar cell is induced by more severe interface and bulk recombination than that of the CdS/CdTe solar cell.     

Thermally evaporated CdS/CdTe thin film solar cells: Optimization of CdCl2 evaporation treatment on absorber layer

CdCl₂ treatment is crucial in the fabrication of highly efficient CdS/CdTe thin-film solar cells. This study reports a comprehensive analysis of thermal evaporated CdS/CdTe thin-film solar cells when the CdTe absorber layer is CdCl₂ annealed at temperatures from 340 to 440 °C. Samples were characterized for structural, optical, morphological and electrical properties. The films annealed at 400 °C showed better crystallinity with a cubic zinc blende structure having large grains. Higher refractive index, optical conductivity, and absorption coefficient were recorded for the CdTe films annealed at 400 °C with CdCl₂. Optimum photoactive properties for CdS/CdTe thin-film solar cells were also obtained when samples were annealed at 400 °C for 20 min with CdCl₂, and the best device exhibited V_OC of 668.4 mV, J_SC of 13.6 mA cm⁻², FF of 53.9% and an efficiency of 4.9%.     

化学水浴法制备大面积CdS薄膜及其光伏应用

采用化学水浴法制备了大面积CdS多晶薄膜,研究了薄膜的形貌、结构和光学性质,结果表明,大面积CdS多晶薄膜具有良好的均匀性,通过优化CdS多晶薄膜,制成了不同CdS窗口层厚度的CdTe小面积太阳电池,减薄CdS薄膜可有效提高器件的短路电流,改善器件性能.随后,在面积30cm×40cm的衬底上制备了全面积为993.6cm²的CdTe太阳电池组件,其27个集成单元的电学性质较为均匀,太阳电池组件的光电转换效率8.13%. 关键词： 化学水浴法(CBD) CdS薄膜 CdTe太阳电池 CdTe太阳电池组件     

Electronic properties and deep level transient spectroscopy of CdS/CdTe thin film solar cells

It is well known that preparing temperatures and defects are highly related to deep-level impurities. In our studies, the CdTe polycrystalline films have been prepared at various temperatures by close spaced sublimation (CSS). The different preparing temperature effects on CdS/CdTe solar cells and deep-level impurities have been investigated by I--V and C--V measurements and deep level transient spectroscopy (DLTS). By comparison, less dark saturated current density, higher carrier concentration, and better photovoltaic performance are demonstrated in a 580oC sample. Also there is less deep-level impurity recombination, because the lower hole trap concentration is present in this sample. In addition, three deep levels, E_v+0.341 eV(H4), E_v+0.226 eV(H5) and E_C-0.147 eV(E3), are found in the 580oC sample, and the possible source of deep levels is analysed and discussed.