Characterization of Indian cigarette tobacco and its smoke aerosol by nuclear and allied techniques

Forty brands of tobacco used in Indian cigarettes, 20 brands of bidis (tobacco rolled in wrapper leaves), 15 brands of chewing tobacco and 15 brands of snuff tobacco were analyzed by nuclear and allied techniques. The elements measured into tobacco can be grouped into seven categories from less than 1 ppm to 5% by weight. Concentration level varied from 0.5-5% for (Ca, K, Cl), 400-1500 ppm (Fe), 200-600 ppm (Na), 100-300 ppm (Ti, Mn, Br and Sr), 10-100 ppm (Cu, Zn and Rb), 1-10 ppm (Cr, Ni, Pb and La) and less than 1 ppm (As, Co, Cd, Sb, Hg and Eu). Among the above elements Cr, Ni, As, Cd, Pb, Hg and Sb are considered toxic. The percentage transfer of the elements from cigarette tobacco to smoke particles during smoking was also estimated using a smoking machine and collecting the smoke particles on a filter paper. The results show that Br, Cr, Sb and Zn have high percentage transfer from tobacco to its smoke of the order of 2-15%. Out of these Sb has the highest 15%. Cobalt, Fe and Sc have lowest percentage of transfer of the order of less than 1%. The percent transfer of these elements from tobacco to tobacco smoke is higher in case of bidis (1.5-3.0 times) as compared to cigarettes. In cigarettes also non-filter cigarettes have higher transfer (2-3 times) as compared to filter tip cigarettes.     

Toxic and essential metals determination in commercial seafood: Paracentrotus lividus by ICP-MS

Toxic and essential metals content was determined by inductively coupled plasma mass spectrometry in commercial sea urchins samples from the Mediterranean Sea and Pacific Ocean. Results show that Chilean samples have the highest values of Cd, As, Ni, Cr and V; Spanish samples have the maximum Hg content while Sicilian samples have the lowest content of toxic metals. The toxic metal traces were compared with the limits of European Community (EC) No. 1881/2006 for bivalve molluscs. All samples exceed Pb and Cd limit levels; regarding Hg levels, only Sicilian and Sardinian samples have Hg content below the EC limits. The dietary intake of toxic and essential elements was evaluated for an adult. Furthermore, our study highlights a correlation between the toxic elements content and the marine environmental conditions of the places of origin even though only the generic FAO fishing area is specified.     

Determination of Essential and Toxic Elements in Vegetables from South Korea

This study reports the determination of trace essential (Co, Cr, Cu, Se, and Zn) and toxic (Al, As, Cd, Hg, and Pb) elements in greenhouse tomatoes, peppers, and cucumbers from supermarkets of Seoul, Busan, Gangneung, Daegu, Daejeon, and Gwangju, South Korea using inductively coupled plasma mass spectrometry, inductively coupled plasma optical emission spectroscopy, and direct mercury analysis. The methods were validated by linearity, limits of detection and quantification, precision, accuracy, and recovery measurements that provided satisfactory results in all cases. Among the essential trace elements, Zn was found to have the highest concentrations (0.84–2.5?mg/kg) followed by Cu (0.21–0.62?mg/kg) and Cr (0.01–0.06?mg/kg). The mean concentrations (mg/kg) of the toxic elements were in the order Al?>?Pb?>?As?>?Cd?>?Hg for tomatoes and cucumbers and Al?>?Pb?>?Cd?>?As?>?Hg for peppers; all were below the permissible limits set by World Health Organization for human consumption. The estimated dietary intake, target hazard quotients (THQs), and hazard indices of the samples were within safe levels. The combined THQ values for the toxic elements in the vegetables were from 0.002 to 0.012 with significant contribution from arsenic, aluminum, cadmium, and mercury. The results of this study show that trace and toxic elements in the analyzed vegetables do not impose any serious health harmful effects for the population upon consumption.     

Determination of minor, trace and toxic elements in chewing tobacco products by instrumental neutron activation analysis and identification of glutamic acid

Tobacco smoking/chewing has been a cause of concern because of it being related with oral cancer. It causes stimulation and ill physiological effects. Ten different brands of spit tobacco, eight gutkaas and five paan masalas have been analyzed for seven minor (Al, Na, K, Ca, Cl, Mg, and P) and 17 trace (As, Ba, Br, Co, Cr, Cs, Cu, Eu, Fe, Hg, La, Mn, Rb, Sb, Sc, Th, and Zn) elements by instrumental neutron activation analysis. Also Ni and Pb were determined by atomic absorption spectrophotometry. Concentration of Cd was below detection limit (<10?mg?kg^?1) in the tobacco samples. Mg, generally added as MgCO₃ to prevent caking, is present as minor constituent in spit tobacco and gutkaas but is below detection limit (<1?g?kg^?1) in paan masalas. Most elemental concentrations vary in a wide range depending on the nature of chewing tobacco. Spit tobacco has been found to be more enriched in essential elements (Ca, K, Na, P, Mn, and Rb), whereas gutkaas contain higher concentrations of Fe, Cr, Cu, and Zn. Paan masalas contain lower contents of other elements but higher content of Hg. Gutkaas also contain higher amounts of As and Pb. Further glutamic acid has been separated from tobacco leaves and characterized as it might bind with some elements.     

Dietary intake of 25 elements by man estimated by neutron activation analysis

The trace element content of the total daily diet (food and beverages) of each of 4 adult males was determined over a period of one week. A method of radiochemical neutron activation analysis is briefly described which enables the determination of up to 31 elements in biological samples. Of the 25 elements determined in the diet 12 are essential elements (Ca, Cl, Co, Cr, Cu, Fe, K, Mn, Mo, Na, Se, Zn) while 6 (As, Ba, Br, Cd, Hg, Sb) are classified as toxic. The average concentrations of the toxic trace elements As, Cd and Hg of the diet are below the provisional tolerable dietary intakes recommended by WHO/FAO. The contents of Cl, Cu, Fe, K, Mn, Na and Zn are adequate to the proposed nutritional requirements.     

Determination of trace and toxic elements in Korean rice CRM by INAA, ICP and AAS

Trace and toxic elements in Certified Reference Material (CRM) made of Korean rice at the Korea Research Institute of Standards and Science have been analyzed by Instrumental Neutron Activation Analysis (INAA). Data intercomparison from the measurement with those of Atomic Absorption Spectrometry (AAS) and Induced Coupled Plasma Spectrometry (ICPS) has been studied. The powdered samples were sterilized at 1.5·10⁶ rad in the bottles using a⁶⁰Co source after sieving and spiking to specific elements such as As, Cd, Cr, Cu and Hg and then the homogeneity of samples was assessed. Rice flour (SRM 1568a) and standard solutions made by the National Institute of Standards Technology (NIST) were used to construct the calibration curves for the INAA and the chemical methods, respectively. The uncertainties and concentration of constituent elements were determined and the possibility of their use for analytical quality control was considered.     

Interlaboratory study of trace and other elements in the iaea powdered human hair reference material,HH-1

A powdered intercomparison material for trace element studies was prepared from human scalp hair and distributed to more than 100 laboratories of which 66 reported results for altogether more than 40 elements. By statistical evaluation of these data certified concentration values were derived for 20 elements, namely As, Au, Br, Ca, Cd, Cl, Co, Cr, Cu, Fe, Hg, Mg, Mn, Na, Pb, S, Sb, Se, Sr and Zn. The data also made it possible to compare different methods of analysis and to judge the value of different levels of experience on the part of the analyst concerned; these comparisons are presented here with special reference to the elements As, Cd, Hg, Pb and Sb.     

Analysis of FDA in-house food reference materials with anticoincidence INAA

In-house reference material (IRM) cocoa powder (CCP) has been in use at US Food and Drug Administration laboratories for about 15 years. A single lot of commercial material was originally characterized for 32 elements by several laboratories and five techniques. A unique approach for basis weight determination based upon ambient relative humidity was developed for CCP, eliminating the need for dry weight determinations. The CCP Reference Sheet is updated by incorporating new results approximately every 5 years. The last update occurred in 2006. As part of an effort to revalidate and update values for CCP, anticoincidence instrumental neutron activation analysis (INAA) was used to determine mass fractions for 16 of the originally characterized elements, as well as to provide information on 16 other elements. Results were in very good agreement with 2006 Reference Sheet values. A new candidate IRM, fresh-frozen swordfish (FFSF) powder, was produced by adding inorganic As, Cd, Cr, Hg, Pb, Sb, and Se to liquid nitrogen-frozen commercial swordfish filets which were then homogenized. Portions of FFSF were analyzed by INAA to provide mass fraction and homogeneity information for As, Cd, Cr, Hg, Sb, and Se as well as for eight other elements occurring naturally in the material. Non-homogeneities were ≤2.5 % for As, Br, Cd, and Cs, and ≤1.8 % for Cr, Hg, Rb, Sb, and Se. Certified reference materials DORM-3 Fish Protein powder and fresh-frozen SRM 1947 Lake Michigan Fish Tissue were analyzed as controls.     

Determination of trace elements by inductively coupled plasma mass spectrometry of biomass and fuel oil reference materials using milligram sample sizes

Most of the analytical techniques used to quantify elements associated with solid samples suffer from high detection limits and cannot be used for trace elements in biomass samples, particularly when only 20 mg are available for analysis. Inductively coupled plasma mass spectrometry (ICP-MS) can achieve detection limits of parts-per-trillion with liquid sample introduction by solution nebulisation. This technique was therefore tested with two standard biomass reference materials: oriental tobacco leaves and cabbage leaves. Two preparations successfully used on coal standards were used to digest the solid samples: a total digestion method (wet ashing digestion) and a partial leaching (microwave extraction). The concentrations of up to seventeen elements (As, Ba, Be, Cd, Co, Cr, Cu, Ga, Mn, Mo, Ni, Pb, Sb, Se, Sn, V and Zn) were measured after the two preparations. The accuracy and sensitivity of the measurements improved when the dilution factor decreased from 5000 to 1000 and to 500. Since the proportion of mineral matter in biomass samples is small (5%), the microwave digestion extracted elements that are generally not completely extracted from coal samples (e.g. Sb). However, some trace element concentrations were below the limit of quantification after microwave extraction, even with a reduced dilution factor (As, Se and Mo) and could not be quantified. A fuel oil was also digested. The trace element concentrations were very low (between 28 and 0.1 microgram g(-1)) but acceptable results were obtained by applying a dilution factor of 100. Only six elements in the fuel oil (As, Ba, Co, Ni, Se and V) had certified or indicated values. Factors affecting the accuracy and sensitivity of the analyses are discussed. The reproducibility of analysis of the tobacco leaf standard was checked over a period of nine months by both digestion methods. The wet ashing method gave acceptable reproducibility for Ba, Cd, Co, Cu, Ga, Mn, Mo, Ni, Pb, V and Zn but poor precision for Cr, Se and Sn and showed evidence of residual chloride interference for As. The microwave extraction gave good reproducibility for As, Ba, Cd, Co, Cr, Cu, Mo, Ni and Zn but poor precision for Se and low recoveries for Ga, Mn, Sn and V. In spite of the small quantities of material analysed, it proved possible to determine the trace elements at levels down to 0.1 microgram g(-1) in the reference materials.     

Determination of toxic and trace elements in algae by instrumental neutron activation analysis

Instrumental neutron activation analysis has been applied in the determination of toxic and other trace elements in a set of three algae materials provided by the International Atomic Energy Agency, with the aim of environmental preservation through enhanced applications of nuclear analytical techniques. The quality of the analysis method has been evaluated by analyzing a number of biological standard reference materials. By adding mineral nutrients, the cultivation of algae for metals is enhanced, in particular, selected toxic heavy metals such as As, Cd, Cr, Hg, Ni and Pb. It is believed that the level of elemental concentration in algae samples are dependent on environmental conditions due to its biochemical properties. Therefore, algae materials may be useful as an indicator or controller of environmental water pollution.     

Trace elements content in size-classified volcanic ashes as determined by inductively coupled plasma-mass spectrometry

At present there is an increasing concern as regards the release of potentially toxic metals into the environment. Volcanic eruptions are a natural source of metals and metalloids in the atmosphere. Toxic trace elements ejected during an eruptive episode may produce hazardous effects for people and the environment in areas close to the volcano. In this context, a study was undertaken to investigate the concentration of metal and metalloids in ashes ejected from Copahue volcano, Neuquén, Argentina. Two samples (A and B) of deposited particles were collected one day after the first eruption and size-fractionated in four sub-samples (S1, S2, S3 and S4). Analysis was performed by inductively coupled plasma-mass spectrometry (ICP-MS) and the accuracy for the entire analytical procedure was performed by means of the certified reference material CRM GBW 07105 Rocks (NRCCRM, China). The elements considered were: As, Cd, Cr, Cu, Hg, Ni, Pb, Sb, U, V and Zn. The adverse effect of potentially interfering species on the mass-spectrometric determination of these elements was also taken into account. The concentration intervals found in the four fractions are as follows (in μg g⁻¹): As, 6.0-2.6; Cd, 0.71-0.36; Cr, 29.5-54.0; Cu, 132-49.0; Hg, 0.020-0.007; Ni, 36.0-26.0; Pb, 15.5-2.55; Sb, 1.07-0.30; U, 2.57-1.94; V, 152-106; Zn, 85.5-55.0. The elements with the highest concentrations were: Cu, V and Zn. All fractions, in both samples, were found to be enriched in some toxic trace elements in the following order Sb>Cd>As. On the contrary, samples were depleted in Ni, Cr and Hg. Lead was the element that exhibits a noticeable difference in concentration between the finer and coarser fractions.     

Evaluation of the bioaccumulation of trace elements in tuna species by correlation analysis between their concentrations in muscle and first dorsal spine using microwave-assisted digestion and ICP-MS

Environmental pollution by metals is a recognized problem worldwide. As a result of the exposure to this pollution, marine species may bioaccumulate metals in both muscle and fishbone, as has been demonstrated in some species of tuna. The objective of this study has been the development and optimization of an inductively coupled plasma-mass spectrometry (ICP-MS) based method, which allows the quantification of 21 elements including priority pollutants and biologically essential elements (B, Mg, Al, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Se, Rb, Sr, Pd, Cd, Ba, La, Hg and Pb) in muscle and in the first spine of the first dorsal fin of albacore (Thunnus alalunga) and bluefin tuna (Thunnus thynnus). A microwave-assisted digestion has been developed for sample treatment, which has been evaluated using isotope dilution analysis (IDA) of Cr, Se, Cd, Ba and Pb. Evaluation of the analytical method in terms of sensitivity (LOQ between 0.002 and 1?mg?kg^?1), accuracy and precision within and between days (CV?<?11.3%) has also been conducted. The developed method has allowed information to be obtained on levels of these metals in both matrices. The correlation analyses performed for each of the metals in both matrices shows a positive linear relationship between the concentrations in muscle and fishbone for Zn, Se, Rb, Cd, As and Hg, which could be due to a higher bioaccumulation of these elements in muscle as it is concluded from the low spine/muscle ratios observed for these elements. The 34 specimens of tuna analyzed show that while the levels of Pb, Cd, Ni, Zn, Cu and Cr in muscle are below the limits set by the WHO/FAO, EC and the US-EPA, Hg shows higher concentration than the limits set by the EC in four samples, indicating a potential risk to human health.     

微波消解-ICP-OES法测定汽车涂料中8种重金属

建立微波消解-电感耦合等离子体发射光谱(ICP-OES)测定汽车涂料中Pb,Cr,Se,Ba,Sb,As,Cd,Hg含量的方法。以HNO_3-H_2O_2(体积比为4∶1)混合酸消解样品,各元素分析谱线:Pb 220.353 nm,Cr 267.716 nm,Se196.090 nm,Ba 233.527 nm,Sb 217.581 nm,As 189.042 nm,Cd 228.802 nm,Hg 184.950 nm。8种元素测定结果的相对标准偏差为2.02%~12.94%(n=6);对白色、蓝色、红色汽车漆样品进行加标回收试验,Pb,Cr,Se,Ba,As,Cd,Hg,的加标回收率为81.26%~99.79%,Sb的回收率为62.43%~87.61%。该方法快速、简便,精密度、准确度较高,可用于汽车涂料中重金属含量的监控。     

黔产市售绿茶重金属的含量特征及健康风险评估

为研究黔产市售绿茶中重金属的含量分布特征及健康风险,以五个生产加工地的黔产市售绿茶为研究对象,分析其9种重金属(Pb、Cr、Cd、Hg、Cu、Zn、Mn、Ni和As)含量,利用美国环境保护署(USEPA)推荐的健康风险评价模型进行人体重金属的健康风险评价。结果表明,五种茶叶中Cr、Cd、Pb、Hg、Cu和As含量均低于国家限量标准。黔产市售绿茶的重金属浸出率大小次序为Zn>Mn>Hg>As>Cd>Pb>Cr>Cu>Ni。健康风险评价结果表明,五个产地的绿茶中重金属通过饮茶途径所产生的健康危害个人年风险大小次序为Cd>As>Mn>Ni>Cr>Hg>Pb>Zn>Cu,茶叶中重金属通过饮茶途径所产生的个人健康危害年风险总和为4.33×10-6~5.73×10-6 a-1,均低于USEPA和ICRP推荐的最大可接受风险水平,表明重金属引起的健康危害极小,其对暴露人群造成的健康危害可忽略不计,绿茶中重金属均处于安全范围内。     

Multielemental Analysis of Agroindustrial By-Products Employed in Animal Feeding by INAA

Instrumental neutron activation analysis (INAA) with gamma-ray spectrometry was applied to determine As, Ca, Cd, Cl, Co, Cu, Cr, Fe, Hg, K, Mg, Mn, Mo, Na, Sb, Se and Zn in the Brazilian agroindustrial by-products. These materials are widely used in ruminant feeding. The results obtained were compared with requirement and maximum tolerable concentrations. The general conclusions from the data obtained were: (1) many by-products presented concentrations of some essential elements lower than the requirement concentrations, while in some concentrations of Cr, Fe, Mg and Se exceeded by a little the maximum tolerable concentrations, (2) the elements As, Cd, Hg and Sb, generally considered toxic, showed concentrations lower than maximum tolerable values.     

Assessment of the health of a river ecosystem due to the impact of pollution from industrial discharge using instrumental neutron activation analysis and inductively coupled plasma-mass spectrometry

Inductively coupled plasma-mass spectrometry (ICP-MS) and neutron activation analysis (NAA) were employed in the determination of heavy metal concentrations in water, plant and sediment samples to assess the extent of heavy metal pollution in a river system which is located within an industrial zone. Elemental concentrations of As, Pb, Hg, Cr, Cu, Cd, Ni and Zn were measured in the samples. Statistical analysis was performed on the data obtained to look for trends in the pollution pattern of these elements on the river system. The trend in concentrations of heavy metals pollution in water samples is in the order of Zn > Cu > Ni > Cr > As > Pb > Hg > Cd, whereas in plants the order is Zn > Cr > Cu > Pb > Ni > As > Hg > Cd and in sediments Zn > Cu > Pb > Ni > As > Hg.     

Some trace elements in the waters,marine organisms and sediments of the Adriatic by neutron activation analysis

A number of investigations of trace elements in the waters, organisms and sediments of the Adriatic, using neutron activation analysis with radiochemical, separations are reported. These include studies of Hg in mussels from the Northern Adriatic, of Hg and Se in edible animals from the Rijeka region, and of seven elements (As, Cd, Cu, Hg, Mn, Se and Zn) in marine invertebrates from the Slovene coast. Additionally, plankton, sediment cores and water samples were taken from a grid of stations covering the whole Adriatic and analyzed for 6 to 11 of the trace elements As, Cd, Co, Cr, Cu, Fe, Hg, Mn, Sb and Zn (Hg only in water). Generally, levels found were not indicative of pollution as compared with oceanic samples, but some evidence of locally increased levels was found, especially for Hg. The levels of eleven trace elements in three marine Intercomparison samples prepared by the IAEA Monaco Laboratory are also presented.     

High-throughput determination of seven trace elements in food samples by inductively coupled plasma-mass spectrometry

A method was developed for high-throughput determinations of 7 elements in food samples, namely antimony (Sb), arsenic (As), cadmium (Cd), chromium (Cr), lead (Pb), mercury (Hg), and tin (Sn). The samples were digested by closed-vessel microwave-assisted digestion using concentrated nitric acid (HNO3) as the medium, followed by microwave- assisted evaporation to concentrate the sample solutions before dilution to the desired volume. The microwave-assisted evaporation procedure effectively reduced the final acid concentration to around 8% before analysis by inductively coupled plasma-mass spectrometry (ICP-MS). This reduction allows determination by ICP-MS to proceed without further sample dilution, which would affect the detection limit. The method was validated, and method recoveries for As, Cd, Cr, Pb, and Hg were within the certified ranges of the chosen certified reference materials. Recoveries of the 7 elements from spiked samples ranged from 93.1 to 103.6%. The standard uncertainties of precision for the 7 elements were between 3.1 and 4.3%. Interlaboratory comparison studies for As, Cd, and Pb gave z-scores ranging from -0.2 to 0.3.     

Summary of preparation and homogeneity characterization of ten agricultural food reference materials for elemental composition

Summary Preparation and development has been completed of ten agricultural/food reference materials (RMs): bovine muscle powder, corn starch, hard red spring wheat flour, soft winter wheat flour, whole milk powder, wheat gluten, corn bran, durum wheat flour, whole egg powder and microcrystalline cellulose. Homogeneity tests for 14 elements, Al, Ca, Cd, Co, Cu, Fe, K, Mg, Mn, Na, Ni, Pb, Sr and Zn were performed by the initiating laboratories by application of precise and reliable analytical methods based on flame atomic absorption spectrometry and graphite furnace atomic absorption spectrometry. An extensive set of analytical results obtained from the interlaboratory cooperative characterization campaign was assessed to provide homogeneity estimates for other elements. Estimates of homogeneity from within-laboratory precision indicated that all materials exhibited acceptable homogeneity for virtually all 29 elements (Al, As, B, Ba, Br, Ca, Cd, Cl, Co, Cr, Cu, Fe, Hg, I, K, Mg, Mn, Mo, N, Na, Ni, P, Pb, Rb, S, Se, Sr, V, Zn) for which best estimate concentration values are available. Two thirds of all homogeneity coefficients of variation were below 5%.     

湖北典型地区茶叶-土壤重金属相关性研究

本文旨在分析湖北典型地区茶叶以及土壤中各种元素的含量,采用原子荧光法(AFS)和电感耦合等离子体质谱法(ICP-MS)等方法对135对茶叶及土壤样品进行测定,并探讨各种元素之间的相互关系和影响。研究结果表明,土壤中元素的分布对茶叶中元素含量分布有一定意义,典型区土壤养分有效磷和碱解氮较丰富,有机质和速效钾较缺乏。典型区茶叶作物表层土壤 Cd、Pb、Cu、Cr、As 均存在不同程度的超标。土壤 Cd 和 Hg 的污染指数高,潜在生态风险强。典型区茶叶可食部分重金属含量均值依次为 Cu>Pb>Cd>Hg>As>Cr,重金属元素在茶叶中含量均为中等变异性。 茶叶对 Cu、Pb 的富集系数明显高于 Hg、As、Cd、Cr,不同茶叶对同一元素的富集能力存在差异。土壤重金属含量与土壤 pH 值、CEC、有效磷、总氮等理化指标关系密切。茶叶重金属含量与土壤重金属含量水平相关性较弱,但与茶叶对重金属的富集能力均呈显著正相关关系。