Remote energy storage in Ni(OH)2 with TiO2 photocatalyst

Oxidative energy generated by UV-irradiated TiO2 photocatalyst was stored in Ni(OH)2 that was 12.5-50 microm apart from the TiO2. It is likely that active oxygen species generated on TiO2 diffused into the gas phase and oxidized Ni(OH)2. Loading the TiO2 with Pt accelerated the remote energy storage by an order of magnitude. It was revealed that the stored energy could be taken out and used chemically or electrochemically. The oxidized Ni(OH)2 was reduced by gaseous formaldehyde, formate, ethanol and H2O2.     

染料敏化太阳电池中双层结构TiO2薄膜空间的电子分布与接触界面转移过程

采用电化学阻抗谱(EIS)研究了双层结构TiO2薄膜的电子积累和与电解液接触界面的电子转移过程. 通过制备纳米颗粒单层和纳米颗粒/亚微米颗粒双层2种不同微结构的TiO2薄膜电极, 对其电容分布、 局域态密度、 薄膜内部电子传输和固/液界面电子转移过程进行了研究. 分析了纳米颗粒/亚微米颗粒双层结构电极对染料敏化太阳电池(DSC)性能的影响. 结果表明, 一定数量的电子会积累在亚微米颗粒层中引起薄膜电极化学电容的增加. 在纳米颗粒层上端覆盖亚微米颗粒后降低了界面复合电阻, 但对薄膜电极的传输性能影响较小. 因此在筛选和制备DSC散射层材料时除应具有良好的光散射性能外, 还应考虑材料的化学电容和界面转移电阻等因素.     

双层分等级TiO_2纳米线制备及其光伏性能研究

采用两步溶剂热反应制备了底层为分等级锐钛矿的TiO_2纳米线阵列,上层为分等级锐钛矿的TiO_2纳米线薄膜的双层结构电极.通过XRD和SEM对其组成和形貌进行了表征,并考察了纳米线薄膜对染料敏化太阳电池(DSSC)光伏性能的影响.实验结果表明,分等级锐钛矿的TiO_2纳米线作为DSSC的光阳极,光电转换效率为4.39%,其效率高于光滑的TiO_2纳米线光阳极电池效率(2.07%).     

Preparation of a nanoporous CaCO3-coated TiO2 electrode and its application to a dye-sensitized solar cell

A nanoporous CaCO3 overlayer-coated TiO2 thick film was prepared by the topotactic thermal decomposition of Ca(OH)2, and its performance as an electrode of a dye-sensitized solar cell was investigated. As compared to bare TiO2, nanoporous CaCO3-coated TiO2 provided higher specific surface area and, subsequently, a larger amount of dye adsorption; this in turn increased short-circuit current (Jsc). Furthermore, the CaCO3 coating demonstrated increased impedance at the TiO2/dye/electrolyte interface and increased the lifetime of the photoelectrons, indicating the improved retardation of the back electron transfer, which increases Jsc, open-circuit voltage (Voc), and fill factor (ff). Thereby, the energy conversion efficiency (eta) of the solar cell improved from 7.8 to 9.7% (an improvement of 24.4%) as the nanoporous CaCO3 layer was coated onto TiO2 thick films.     

Boosting the Energy Density of Flexible Asymmetric Supercapacitor with Three Dimensional Fe2O3 Composite Brush Anode

Flexible asymmetric supercapacitor is fabricated with three dimensional(3D)Fe2O3/Ni(OH)2 composite brush anode and Ni(OH)2/MoO2 honeycomb cathode.Particularly for 3D composite brush anode,a layer of thin Fe2O3 film is firmly adhered on a 3D Ni brush current collector with the assist of Ni(OH)2,functioning as both adherence layer and pseudocapacitive active material.The unique 3D Ni brush current collector possesses large surface area and stretching architecture,which facilitate to achieve the composite anode with high gravimetric capacitance of 2158 F/g.In terms of cathode,Ni(OH)2 and MoO2 have a synergistic effect to improve the specific capacitance,and the resulting Ni(OH)2/MoO2 honeycomb cathode shows a very high gravimetric capacitance up to 3264 F/g.The asymmetric supercapacitor(ASC)has balanced cathode and anode,and exhibits an ultrahigh gravimetric capacitance of 1427 F/g and an energy density of 476 W·h/kg.The energy density of ASC is 3-4 times higher than those of other reported aqueous electrolyte-based supercapacitors and even comparable to that of commercial lithium ion batteries.The device also shows marginal capacitance degradation after 1000 cycles'bending test,demonstrating its potency in the application of flexible energy storage devices.     

Lipid bilayer membrane with atomic step structure: supported bilayer on a step-and-terrace TiO2(100) surface

The formation of a supported planar lipid bilayer (SPLB) and its morphology on step-and-terrace rutile TiO 2(100) surfaces were investigated by fluorescence microscopy and atomic force microscopy. The TiO 2(100) surfaces consisting of atomic steps and flat terraces were formed on a rutile TiO 2 single-crystal wafer by a wet treatment and annealing under a flow of oxygen. An intact vesicular layer formed on the TiO 2(100) surface when the surface was incubated in a sonicated vesicle suspension under the condition that a full-coverage SPLB forms on SiO 2, as reported in previous studies. However, a full-coverage, continuous, fluid SPLB was obtained on the step-and-terrace TiO 2(100) depending on the lipid concentration, incubation time, and vesicle size. The SPLB on the TiO 2(100) also has step-and-terrace morphology following the substrate structure precisely even though the SPLB is in the fluid phase and an approximately 1-nm-thick water layer exists between the SPLB and the substrate. This membrane distortion on the atomic scale affects the phase-separation structure of a binary bilayer of micrometer order. The interaction energy calculated including DLVO and non-DLVO factors shows that a lipid membrane on the TiO 2(100) gains 20 times more energy than on SiO 2. This specifically strong attraction on TiO 2 makes the fluid SPLB precisely follow the substrate structure of angstrom order.     

Preparation of nanoporous MgO-coated TiO2 nanoparticles and their application to the electrode of dye-sensitized solar cells

Sol-gel-derived Mg(OH)(2) gel was coated onto TiO(2) nanoparticles, and the subsequent thermal topotactic decomposition of the gel formed a highly nanoporous MgO crystalline coating. The specific surface area of the electrode that was prepared from the core-shell-structured TiO(2) nanoparticles significantly increased compared with that of the uncoated TiO(2) electrode. The increase in the specific surface area of the MgO-coated TiO(2) electrode was attributed to the highly nanoporous MgO coating layer that resulted from the topotactic reaction. Dye adsorption behavior and solar cell performance were significantly enhanced by employing the MgO-coated TiO(2) electrode. Optimized coating of a MgO layer on TiO(2) nanoparticles enhanced the energy conversion efficiency as much as 45% compared to that of the uncoated TiO(2) electrode. This indicates that controlling the extrinsic parameters such as the specific surface area is very important to improve the energy conversion efficiency of TiO(2)-based solar cells.     

染料敏化TiO2/WO3薄膜电池的光电变色

The light-to-electricity conversion process of the TiO2 nanostructured electrode sensitized by a dye was investigated using the photoelectrochemical method in this paper. At the same time, the WO3 thin film was electrodeposited on conducting glass. The results showed that the dye-sensitized nanoporous TiO2 film has the properties of energy conversion, along with good electrochromic properties of electrodeposited MoO3 thin film. A self-powered smart window was achieved by combining a dye-sensitized nanoporous TiO2 film as the photovoltaic layer and an electrodeposited WO3 film as the electrochromic layer. This window changed from being almost transparent to blue spontaneously under illumination, and thus could modulate light transmittance.     

Dye-sensitized solar cells based on multiwalled carbon nanotube-titania/titania bilayer structure photoelectrode

Dye-sensitized solar cells (DSSCs) were fabricated using multiwalled carbon nanotube (MWCNT)-TiO(2) nanocomposite as a light scattering layer. Morphology of the MWCNT-TiO(2) film was investigated by field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM). FESEM and TEM images demonstrate that MWCNTs and TiO(2) nanoparticles can be dispersed with chitosan. Internal resistance in the DSSC was characterized by electrochemical impedance spectroscopy (EIS). EIS results reveal a decrease in the charge resistance of electrolyte/dye/MWCNT-TiO(2)/TiO(2) interface with increasing MWCNT content up to 3 wt% which leads to an improvement in the photovoltaic performance. Compare with a nanocrystalline TiO(2) single-layer cell, the DSSC based on the MWCNT (3 wt%)-TiO(2)/TiO(2) bilayer structure photoelectrode shows ~100% increase in solar-to-electric energy conversion efficiency, which is attributed to the inclusion of MWCNTs in TiO(2) matrix.     

NanoTiO2-CNT复合膜电极在DMF溶液中对糠醛的异相电催化还原

通过在乙醇中电化学溶解Ti金属阳极合成前驱体Ti(OEt)4和溶胶-凝胶法在Ti表面修饰一层纳米TiO2-碳纳米管(nanoTiO2-CNT)复合膜, 采用循环伏安和电解合成法研究了nanoTiO2-CNT复合膜电极在N, N-二甲基甲酰胺(DMF)中的氧化还原行为以及对糠醛(furfural)还原的电催化活性. 结果发现, nanoTiO2-CNT电极在阴极扫描时有两对氧化还原峰, 可逆半波电位E r1/2 分别为－1.27 V和－2.44 V(vs SCE, 扫描速度100 mV•s-1), 分别对应于TiO2/Ti2O3氧化还原电对的可逆电极过程和TiO2/Ti(OH)3电对的准可逆电极过程；在DMF电解液中nanoTiO2-CNT复合膜中的Ti(IV)/Ti(III)氧化还原电对作为媒质间接电还原糠醛为糠醇, 反应机理为电化学偶联随后化学催化反应(EC′)机理.     

Hydrogen transport through Pd-Ni alloy electrodeposited on Pd substrate

Hydrogen transport through a Pd-Ni alloy electrodeposited on a Pd substrate (Pd-Ni/Pd bilayer symmetric electrode) has been investigated using cyclic voltammetry and a.c. impedance spectroscopy combined with the electrochemical hydrogen permeation method. The permeation build-up current transients and the measured impedance spectra were analyzed using the time-lag method for the bilayer electrode and a complex non-linear least squares data-fitting method based upon the derived Faradaic admittance for the hydrogen absorption into and diffusion through the bilayer electrode under the permeable boundary condition, respectively. The value of the hydrogen diffusivity in the Pd-Ni layer was lower than that in the Pd layer. Furthermore, the values of the charge transfer resistance and equilibrium absorption constant for the Pd-Ni/Pd bilayer electrode were higher than those for the Pd single layer electrode. From the experimental results, the role of the thin Ni(OH)₂ film formed on the Pd-Ni layer surface in the hydrogen transport through the Pd-Ni/Pd bilayer electrode is discussed in terms of its passivating effect and extremely large hydrogen solubility. Received: 22 January 1997 / Accepted: 15 April 1997     

Ni-W-TiO2复合电极在碱性介质中的析氢电催化性能

具有较高的析氢电催化活性的镍基多元合金材料已广为报道。近年来通过复合电沉积技术在电极中掺入RuO2、ZrO2、WC等非溶性固体微粒制备的复合功能电极材料用于析氢方面的研究已有报道,这些复合电极对析氢反应都有明显的催化作用。但是用电沉积的方法在电极中掺入TiO2制备的复合功能材料的研究还未见报道,本文研究了Ni-W-TiO2复合电极的制备、形貌结构以及在碱性介质中的析氢电催化活性和电化学稳定性。     

TiO_2聚苯胺复合膜的光电化学

利用电化学方法制备了TiO2 聚苯胺 (PANI)复合膜 .该膜具有比TiO2 或PANI膜更宽的吸收谱区 ,并且不同于利用聚苯胺光敏化的TiO2 膜 ,表现为两者复合材料膜的性质 .扫描电镜图表明 ,TiO2 微粒不完全覆盖着PANI膜 .根据TiO2 微粒光电流谱带的阈值能可得复盖在部分氧化态聚苯胺膜上的TiO2 微粒的禁带宽度为 3.0eV .部分氧化态聚苯胺膜的光电流谱遵循Fowler定律 ( 1/2 ～hυ成线性 ) .通过Fowler图得出部分氧化态聚苯胺的绝缘母体禁带宽度为 3.33eV ,并证实该绝缘母体为还原态聚苯胺 .从Mott Schottky图得到在 0 .0 5mol/LK3Fe(CN) 6 /K4 Fe(CN) 6 溶液中 (pH =8.52 )部分氧化态聚苯胺的平带电位为 0 .13V ,掺杂浓度为 5.3× 10 18cm- 3;TiO2 PANI复合膜的平带电位为 - 0 .6 5V ,掺杂浓度为 9.1× 10 19cm- 3.解释了TiO2 PANI复合膜的光电化学过程并描绘出其能带图 .利用TiO2 PANI复合膜能够有效地光降解苯酚溶液 .     

固定在氧扩散膜表面的TiO2光催化膜

本文提出用氧扩散膜作TiO₂光催化膜的载体,介绍了氧扩散膜的制备及TiO₂在氧扩散膜表面的固定方法,TiO₂光催化膜的表面形态与微结构,不同条件下光催化分解草酸的速度.研究结果表明,以氧扩散膜作载体的TiO₂光催化薄膜表现出了较高的光催化活性.文中详细分析了氧扩散膜的作用.     

Enhanced remote photocatalytic oxidation on surface-fluorinated TiO2

The mobile nature of active oxygen species generated on the UV-illuminated TiO2 surface is now well-recognized. Surface oxidants not only migrate two-dimensionally but also desorb from the surface to be air-borne oxidants. The remote photocatalytic oxidation (PCO) of stearic acids over the surface-fluorinated TiO2 (F-TiO2) film was carried out in the ambient air to study the effects of fluorination on the desorption of oxidants from the surface. The F-TiO2 film was faced to a stearic acid-coated glass plate separated by a small gap (typically 30 microm), and the photocatalytic degradation of the stearic acid was monitored by Fourier transform infrared measurement or gas-chromatographic CO2 production analysis. Remote photocatalytic degradation of stearic acids was markedly faster with F-TiO2 than with the pure TiO2 film, which indicates that the generation of air-borne oxidants is enhanced over the F-TiO2 surface. The remote PCO activity was higher with a higher surface fluoride concentration, higher UV intensity, and smaller gap. The remote photocatalytic activity of F-TiO2 was maximal at a relative humidity of 50% and did not show any sign of deactivation with repeated reactions. The production of CO2 that evolved as a result of the remote PCO of stearic acids was enhanced when H2O2 vapor was present but was strongly inhibited in the presence of ammonia gas that should scavenge OH radicals. Judging from various evidences, the air-borne oxidants in remote PCO are most likely OH radicals and the surface fluorination of TiO2 seems to facilitate the desorption of OH radicals.     

医用多孔NiTi合金表面溶胶-凝胶法制备TiO2涂层

采用溶胶-凝胶法结合浸渍提拉工艺在多孔NiTi合金表面制备出了结构均一的锐钛矿型TiO2涂层,并在溶胶中添加聚乙二醇(PEG)作为造孔剂,进而在多孔NiTi合金表面制备出内层致密、外层多孔的TiO2复合涂层。SEM分析结果表明,TiO2涂层均匀地覆盖了多孔NiTi合金基体的外表面以及孔的内表面。Hanks溶液中的阳极极化曲线结果表明,与未处理的多孔NiTi合金相比,具有致密TiO2涂层的多孔NiTi合金其耐腐蚀性能有了显著提高。而多孔TiO2复合涂层进一步增大了多孔NiTi合金的实际表面积,提高了材料表面的生物活性。     

TiO2纳米片/巢状分级结构纳米阵列薄膜的制备及其在染料敏化太阳能电池中的应用

采用水热合成法在氟掺杂二氧化锡(FTO)导电玻璃基底上得到TiO2纳米阵列薄膜,并进一步通过NaOH溶液水热处理制备了由巢状纳米阵列及纳米片覆盖层构成的TiO2纳米阵列分级结构一体化薄膜.采用场发射扫描电镜(FE-SEM),X射线衍射(XRD),紫外-可见(UV-Vis)漫反射光谱和吸收光谱技术对TiO2薄膜的结构和性质进行表征.FE-SEM结果表明:分级结构TiO2薄膜膜厚为1.5μm,薄膜由一层纳米片覆盖层(约0.2μm高)和一层巢状纳米阵列层(约1.3μm高)组成.XRD谱图表明TiO2薄膜为锐钛矿相.UV-Vis光谱显示分级结构TiO2薄膜具有较强的光捕获能力和染料吸附能力.TiO2纳米片/巢状分级结构纳米阵列薄膜作为光阳极,可有效地提高染料敏化太阳能电池的光电转换效率,其短路电流(Jsc)为7.79mA·cm-2,开路电压(Voc)为0.80V,填充因子(FF)为0.40,光电转换效率(η)为2.48%,其光电转换效率较TiO2纳米阵列薄膜提高了近10倍.     

MRCI investigation of different isomers of Ni2O2H2(+)

The geometrical and electronic structures of different isomers of Ni(2)O(2)H(2)(+) are investigated by multireference configuration interaction (MRCI) calculations using natural atomic orbital basis sets. The lowest-lying isomer, Ni(2)(OH)(2)(+), has a rhombic shape with two OH groups bridging the Ni atoms. The next isomer in energetic order with a relative energy of 0.29 eV consists of a linear NiONi(OH(2))(+) chain. Other structures with a rhombic shape, (NiH)(2)O(2)(+), with H bound to the Ni atoms have considerably higher energies, above 4 eV. Especially the low-lying isomers are characterised by a large number of low-lying electronic terms. The product Ni(2)O(2)H(2)(+) of the reaction of Ni(2)O(2)(+) with small alkanes is likely to have the rhombic Ni(2)(OH)(2)(+) structure. The reaction energy of the reaction Ni(2)O(2)(+) + H(2)→ Ni(2)(OH)(2)(+) is estimated to be about -3.5 eV.     

TiO2/SnO2复合空心球在染料敏化太阳能电池中的应用

采用模板辅助法制备了SnO2/TiO2复合空心球,样品直径为1.5~4.0μm,比表面积达到了92.9 m^2·g^-1,复合空心球表现出优越的光散射性能.以这种复合空心球作为染料敏化太阳能电池的光阳极,电池的光电转换效率可达到7.72%,高于SnO2微米球(2.70%)和TiO2微米球(6.26%).此外,以锐钛矿型TiO2纳米晶作为底层,SnO2/TiO2复合空心球作为光散射层制备的双层结构光阳极,电池光电转换效率进一步提升至8.43%.     

温度对掺杂球形Ni(OH)_2质子扩散的影响

应用微电极恒电位阶跃法研究了在Ni(OH) 2 电极的阳极及阴极过程反应中 ,温度对球形Ni(OH) 2 的质子扩散系数和表观扩散活化能的影响 .研究表明 ,于Ni(OH) 2 中掺杂Co和Co +Zn后可降低其阳极和阴极过程的表观扩散活化能 ,增大质子扩散系数 ,掺Co的效果更加明显 ,而掺Zn则增大表观扩散活化能 ,降低了扩散系数 .这说明前者的掺入其作用是降低了质子扩散阻力使电极的反应活性增加、而后者的掺入则是增大了质子的扩散阻力而使电极反应活性降低 .