Suppression of gain narrowing in multi-TW lasers with negatively and positively chirped pulse amplification

A laser scheme implementing a combination of negatively and positively chirped pulse amplification (NPCPA) is demonstrated. This method of amplification suppresses spectral narrowing typically appearing in chirped pulse amplification (CPA) lasers thus supporting pulse spectrum much broader than a conventional CPA. With a NPCPA Ti:Sapphire laser we have achieved laser pulses of 50 nm spectral width and 150 mJ energy without any additional spectral correction. The scheme appears as an easy and reliable solution to preserve spectral bandwidth in Ti:Sapphire lasers, especially at high power levels up to the Petawatt regime. PACS 42.60 By, Lh; 42.65 Re     

Generation of accurately synchronized pump source for optical parametric chirped pulse amplification

We demonstrate the generation of ultra-short pulses at 1064 nm by continuous-wave seeded non-collinear optical parametric amplification in a -barium borate crystal pumped by the second harmonics of a femtosecond Ti:sapphire laser. After two stages of seeded parametric amplifiers, the generated pulses at 1064 nm were accurately synchronized with the fundamental pump pulses, which could be used as seeding pulses for further amplification and then frequency doubling to produce an accurately synchronized pump source for optical parametric amplification of chirped pulses from the same Ti:sapphire laser. PACS 42.65.Re; 42.65.-k; 52.35.Mw     

输出能量4mJ的1kHz飞秒掺钛蓝宝石激光再生放大研究

针对高能量千赫兹重复频率飞秒激光的应用需求,设计了一套采用线性再生腔结构的高效率飞秒钛宝石激光啁啾脉冲放大系统.通过优化腔型设计,在重复频率为1 kHz、单脉冲能量为20 mJ的527 nm激光抽运下,将展宽后的800 nm啁啾脉冲激光的能量放大到5.8 mJ,对应斜效率达到30.7%.进一步通过色散补偿压缩脉冲宽度,获得了单脉冲能量为4 mJ、脉冲宽度为45.7 fs的输出,稳定性测量表明激光的能量抖动仅为0.18%(均方根值).     

Optical parametric chirped pulse amplification based on photonic crystal fibre

A compact two-stage optical parametric chirped pulse amplifier based on photonic crystal fibre is demonstrated.A 1064-nm soliton pulse is obtained in a home-made photonic crystal fibre (PCF) with femtosecond pulse pumping and then amplified to 2 mJ in an Nd:YAG regenerative amplifier.After the amplified pulses pass through the LBO crystal,the 532-nm double-frequency light with an energy of 0.8 mJ and a duration of over 100 ps at 10-Hz repetition rate is generated as a pump source in the following two-stage optical parametric amplification (OPA).The 850-nm chirped signal light gain from the stretcher is 1.5×10 4 in the first-stage OPA while it is 120 in the second-stage OPA.The total signal gain of optical parametric chirped pulse amplification (OPCPA) can reach 1.8×10 6.     

57 W, 27 fs pulses from a fiber laser system using nonlinear compression

We report on the generation of 27 fs pulses with an average output power of 57 W and a repetition rate of 78 MHz. The pulses are generated by combining a high average power fiber chirped pulse amplification (FCPA) system with a microstructured large-mode-area fiber for nonlinear compression. The FCPA system delivers 270 fs pulses in a linearly polarized beam with diffraction-limited quality. Nonlinear compression is achieved by launching the pulses into a short (few cm) piece of microstructured fiber and subsequent compression by a pair of chirped mirrors. PACS  42.55.Wd; 42.55.Xi, 42.65.Re     

Multi-terawatt laser system generating 12-fs pulses at 100 Hz repetition rate

We have developed a laser system generating high peak-power ultrashort pulses based on the chirped pulse amplification of a Ti:sapphire laser. The pulse duration of the laser is reduced to 12 fs, owing to the successful compensation of gain narrowing during amplification with novel optics. The pulse energy and the repetition rate are 40 mJ and 100 Hz, respectively, as a consequence of sufficient energy extraction from a laser medium in the final stage of a multipass amplifier chain, which is designed to balance focusing with a thermal lens against defocusing with convex mirrors without cryogenic cooling for Ti:sapphire crystals. The laser pulses delivered from this laser system are suitable for generating an intense attosecond pulse train in a vacuum ultraviolet or extreme ultraviolet region.     

Picosecond optical parametric amplification of stimulated Raman as high peak-power source and ultra-sensitive preamplifier

We report the characteristics of the amplified stimulated Raman scattering (SRS) pulses generated in liquid benzene by a picosecond (ps) β-barium borate (BBO) optical parametric amplifier (OPA). When the OPA system was used as an energy amplifier for SRS pulses, with a pump energy of 2.4 mJ at 355 nm for the OPA, the maximum output energy of the amplified SRS was about 0.73 mJ for the signal and 0.18 mJ for the idler, the energy conversion efficiency was 30.4% from the pump beam to the amplified third order Stokes component at 635.1 nm. The total efficiency would be as high as 37.9% if the output of the idler is also included. The corresponding spectral line width of the amplified Raman pulse was 11.8 cm⁻¹ with a pulse width of 10.9 ps and a peak power of 67 MW. The OPA system was also used as an amplifier for very weak Raman signal, the slope gain factor of this amplifier was found to be as high as 4.1 × 10⁷ and the energy detection limit was as low as 14.8 aJ per pulse, or 48 photons at 635.1 nm, in particular. Such a detection limit corresponds to approximately 0.5 photons per pulse if the time-gate of the OPA is reduced to 150 fs and it is about the same as or even better than a recently report on the 0.75 photons detection limit for a 150-fs OPA of coherent signal at 800 nm.     

A powerful diode-pumped laser source for micro-machining with ps pulses in the infrared, the visible and the ultraviolet

We report a ps diode-pumped Nd:YVO₄ laser system for micro-machining applications. The system consists of a passively mode-locked oscillator followed by a regenerative amplifier. It provides laser pulses at 1064 nm with a pulse duration of 10.2 ps, a repetition rate of 20 kHz and an average output power of 10.8 W. This average power corresponds to a pulse energy of 0.54 mJ. Second-harmonic generation in LBO and fourth-harmonic generation in BBO provide visible (532-nm) and ultraviolet (266-nm) radiation with pulse energies of 270 J and 75 J, respectively. Amplification in a diode-pumped single-pass Nd:YVO₄ amplifier increases the pulse energy of the fundamental 1064-nm laser pulses to 1 mJ. PACS 42.55.Xi; 42.60.Da; 42.65.Ky; 42.65.Re     

Multiterawatt laser system based on optical parametric chirped pulse amplification

A compact multiterawatt laser system based on optical parametric chirped pulse amplification is demonstrated. Chirped pulses are amplified from 20 pJ to 900 mJ by two lithium triborate optical parametric preamplifiers and a final KDP optical parametric power amplifier with a pump energy of 5 J at 532 nm from Nd:YAG-Nd:glass hybrid amplifiers. After compression, we obtained a final output of 570-mJ-155-fs pulses with a peak power of 3.67 TW, which is the highest output power from an optical parametric chirped pulse amplification laser, to the best of our knowledge.     

Compact 120 TW Ti:sapphire laser system with a high gain final amplifier

A 120 TW/36 fs laser system based on Ti:sapphire chirped-pulse amplification (CPA) has been successfully established in our lab. The final four pass Ti:sapphire amplifier pumped by an energetic single-shot Nd:YAG—Nd:glass laser was designed and optimized. With 24 J/8 ns pump energy at 532 nm, 300 mJ/220 ps chirped pulse was amplified to 5.98 J in this amplifier, and a total saturated gain of 20 was achieved. The focused intensity of compressed beam could reach to 10²⁰ W/cm² with the M² of 2.0.     

Yb:YAG Innoslab amplifier: efficient high repetition rate subpicosecond pumping system for optical parametric chirped pulse amplification

We report on a Yb:YAG Innoslab laser amplifier system for generation of subpicsecond high energy pump pulses for optical parametric chirped pulse amplification (OPCPA) at high repetition rates. Pulse energies of up to 20 mJ (at 12.5 kHz) and repetition rates of up to 100 kHz were attained with pulse durations of 830 fs and average power in excess of 200 W. We further investigate the possibility to use subpicosecond pulses to derive a stable continuum in a YAG crystal for OPCPA seeding.     

Intense femtosecond pulse shaping using a fused-silica spatial light modulator

We present the design concept of a setup of a pulse shaper to be used for high-power femtosecond lasers. The pulse shaper is constructed from a high-damage threshold fused-silica spatial light modulator and a 4-f optical system based on the design concept to avoid optical damage. We have successfully demonstrated a pulse compression of 20 fs, 5 mJ pulses obtained from a 1 kHz repetition rate Ti:sapphire chirped pulse amplification system at an average power of 5 W.     

Stacking chirped pulse optical parametric amplification

Stacking chirped pulse optical parametric amplification based on a home-built Yb³⁺-doped mode-locked fiber laser and an all-fiber pulse stacker has been demonstrated. Energic 11 mJ shaped pulses with pulse duration of 2.3 ns and a net total gain of higher than 1.1 × 10⁷ at fluctuation less than 2% rms are achieved by optical parametric amplification pumped by a Q-switched Nd:YAG frequency-doubled laser, which provides a simple and efficient amplification scheme for temporally shaped pulses by stacking chirped pulse.     

Active mode locking of a phase-conjugating SBS-laser oscillator

We present a flashlamp-pumped Nd:YAG laser simultaneously emitting pulse structures on microsecond, nanosecond and picosecond time scales. Within a microsecond flashlamp pump pulse a nonlinear reflector based on stimulated Brillouin scattering (SBS) generates several Q-switch pulses. The phase-conjugating effect of the SBS reflector provides a compensation of phase distortions generated inside the laser rod, resulting in transverse fundamental mode operation. Additional acousto-optic loss modulation inside the resonator leads to mode locking. As a result, each Q-switch pulse is subdivided into several picosecond pulses. Energies of up to 2 mJ for the mode-locked pulses with durations between 220 and 800 ps are demonstrated. The wide variability of the lasers temporal output parameters as well as its high beam quality make it a splendid tool for fundamental research in laser materials processing. PACS 42.60.Fc; 42.60.Gd; 42.65.Es     

用钛宝石再生放大器产生高重复率啁啾脉冲列

针对啁啾脉冲放大技术建成的钛宝石激光装置，提出一种获得高重复率激光脉冲列的方法.通过改变钛宝石再生放大器中泡克耳斯盒电光开关的传统工作模式，使得腔内放大的脉冲从某特定时刻起，每当在腔内往返一次就以一定的倒出比例（倒出率）倒出腔内脉冲能量的一部分，从而可以在有限的时间段内产生高重复率的啁啾激光脉冲列.基于Franz-Nodvik放大理论，建立了该高重复率再生放大器的理论模型，通过数值计算，系统地分析了初始增益、倒出时刻、倒出率对输出的脉冲序列的影响.在抽运功率为35mJ、倒出率为1/2的实验条件下，通过腔外的脉冲数量选择器，在一个抽运周期内的有限时间段内已获得了14个幅度相近、单脉冲能量约为0.02mJ、重复率为100MHz的啁啾脉冲序列.从此啁啾脉冲列中选取数个脉冲，通过10TW级的激光系统放大和压缩，已获得100MHz重复率的飞秒太瓦级脉冲列. 关键词： 高重复率 多通放大 啁啾脉冲放大 钛宝石激光器     

采用环形再生腔结构的飞秒激光啁啾脉冲放大研究

采用环形再生腔结构的啁啾脉冲放大技术方案, 在重复频率100 Hz,单脉冲能量33.1 mJ的532 nm激光抽运下, 从钛宝石激光中获得了单脉冲能量9.84 mJ的放大输出, 对应的斜效率达33.1%.在重复频率10 Hz的情况下, 同样获得了单脉冲能量为9.64 mJ, 对应斜效率达36.8%的高效率放大结果. 通过色散补偿压缩该啁啾激光脉冲后的单脉冲能量为6.36 mJ, 脉冲宽度为59.7 fs. 测量结果表明典型的能量不稳定度为1.85%. 关键词： 啁啾脉冲放大 再生放大 飞秒激光 环形腔     

多波段紫外太瓦级CPA系统

基于啁啾脉冲放大(CPA)技术和频率变换技术,构建了一个多波长紫外太瓦量级CPA系统.该系统实现了5种频率的精确同步,可同时输出1 Hz,5 Hz和10 Hz的高能量多波段紫外脉冲.时间抖动小于3 ns的时间同步系统和能量不稳定性小于0.5%rms的kHz预放大系统保证了CPA系统输出的能量不稳定性小于2%rms.最后,通过共线相位匹配方案,得到了64 mJ/400 nm,16 mJ/267 nm和5 mJ/205 nm紫外脉冲输出,对应峰值功率达到太瓦量级. 关键词： 啁啾脉冲放大 光学频率变换 紫外脉冲     

Generation of synchronized signal and pump pulses for an optical parametric chirped pulse amplification based multi-terawatt Nd:glass laser system

Synchronized signal (650 ps) and pump (1.3 ns) pulses were generated using 4-pass geometry in a grating pair based pulse stretcher unit. The pump pulse has been further amplified in a high gain regenerative amplifier. This amplified pulse was used as the pump in an optical parametric chirped pulse amplification based Nd:glass laser system. As the chirped signal pulse and the pump pulse originated from the same oscillator, the time jitter between the pump pulse and the signal pulse can be <50 ps.     

低重复率的Ti:Al2O3飞秒激光放大器研究

本文报道了重复频率为10Hz的Ti:Al₂O₃飞秒激光放大器的研究.基于脉冲啁啾放大技术和采用再生/多通放大装置,得到了能量为8mJ的放大光脉冲,在该放大系统中,激光脉冲获M净增益约8×10⁷.