X-ray photoelectron spectroscopic and electrochemical impedance spectroscopic analysis of RuO2-Ta2O5 thick film pH sensors

The paper reports on investigation of the pH sensing mechanism of thick film RuO₂-Ta₂O₅ sensors by using X-ray photoelectron spectroscopy (XPS) and electrochemical impedance spectroscopy (EIS). Interdigitated conductimetric pH sensors were screen printed on alumina substrates. The microstructure and elemental composition of the films were examined by scanning electron microscopy and energy dispersive spectroscopy. The XPS studies revealed the presence of Ru ions at different oxidation states and the surface hydroxylation of the sensing layer increasing with increasing pH. The EIS analysis carried out in the frequency range 10 Hz–2 MHz showed that the electrical parameters of the sensitive electrodes in the low frequency range were distinctly dependent on pH. The charge transfer and ionic exchange occurring at metal oxide-solution interface were indicated as processes responsible for the sensing mechanism of thick film RuO₂-Ta₂O₅ pH sensors.     

Effects of Polymer Binder,Surfactant and film Thickness on pH Sensitivity of Polymer Thick Film Sensors

Measuring the change of the conductivity of a Polyaniline (PANI) film while in contact with a solution is considered to be a costeffective tool for pH sensing. The device consists of a PANI film deposited between two identical electrodes, reducing the number of fabrication steps. To ensure the sensors display an optimum response to solutions of different pH values, it is important to understand the effect of the polymer binder, surfactant and film thickness. The effect of varying the amount of Polyvinyl butyral (PVB) and Hypermer (PS3) on the pH sensitivity of screen printed thick film sensors is reported.     

Humidity sensors using in situ synthesized sodium polystyrenesulfonate/ZnO nanocomposites

Thin film humidity sensors have been prepared using in situ synthesized inorganic/organic nanocomposites of sodium polystyrenesulfonate (NaPSS) and ZnO. Its humidity sensing characteristics and the sensing mechanism have been investigated by measuring the complex impedance spectra of the sensor at different humidities. The logarithm of the impedance of sensor based on composite film changes linearly by four-orders of magnitude over almost whole humidity range (11-97% RH). Furthermore, the sensor exhibits a quick response (absorption: 2 s, desorption: 2 s) and small hysteresis (less than 2% RH). The composite film shows better sensing properties than NaPSS film, such as better linearity, quicker response. Explanation to the improvement is attempted by taking into account of the composition and structure of the nanocomposites.     

Ionic transport studies on (PEO)6:NaPO3 polymer electrolyte plasticized with PEG400

Conduction characteristics of the poly(ethylene oxide) based new polymer electrolyte (PEO)₆:NaPO₃, plasticized with poly(ethylene glycol) are investigated. Free standing flexible electrolyte films of composition (PEO)₆:NaPO₃ + x wt.% PEG₄₀₀ (30 ? x ? 70) are prepared by solution casting method. A combination of X-ray diffraction (XRD), optical microscopy and differential scanning calorimetry (DSC) studies have indicated enhancement in the amorphous phase of polymer due to the addition of plasticizer. Further, a reduction in the glass transition temperature observed from the DSC result has inferred increase in the flexibility of the polymer chains. The cationic transport number (t_Na⁺) of 0.42 determined through combined ac-dc technique has confirmed ionic nature of conducting species. Ionic conductivity studies are carried out as a function of composition and temperature using complex impedance spectroscopy. The electrolyte with maximum PEG₄₀₀ content has exhibited an enhancement in the conductivity of about two orders of magnitude compared to the host polymer electrolyte. The complex impedance data is analyzed in conductivity, permittivity and electric modulus formalism in order to throw light on transport mechanism. A solid state electrochemical cell based on the above polymer electrolyte with a configuration Na|SPE|(I₂ + acetylene black + PEO) has exhibited an open circuit voltage of 2.94 V. The discharge characteristics are found to be satisfactory as a laboratory cell.     

Development of miniaturized pH biosensors based on electrosynthesized polymer films

A new type of pH biosensor was developed for biological applications. This biosensor was fabricated using silicon microsystem technology and consists in two platinum microelectrodes. The first microelectrode was coated by an electrosynthesized polymer and acted as the pH sensitive electrode when the second one was coated by a silver layer and was used as the reference electrode. Then, this potentiometric pH miniaturized biosensor based on electrosynthesized polypyrrole or electrosynthesized linear polyethylenimine films was tested. The potentiometric responses appeared reversible and linear to pH changes in the range from pH 4 to 9. More, the responses were fast (less than 1 min for all sensors), they were stable in time since PPy/PEI films were stable during more than 30 days, and no interference was observed. The influence of the polymer thickness was also studied.     

Polymerized Nile Blue derivatives for plasticizer-free fluorescent ion optode microsphere sensors

Lipophilic H⁺-selective fluorophores such as Nile Blue derivatives are widely used in ISE-based pH sensors and bulk optodes, and are commonly dissolved in a plasticized matrix such as PVC. Unfortunately, leaching of the active sensing ingredients and plasticizer from the matrix dictates the lifetime of the sensors and hampers their applications in vivo, especially with miniaturized particle based sensors. We find that classical copolymerization of Nile Blue derivatives containing an acrylic side group gives rise to multiple reaction products with different spectral and H⁺-binding properties, making this approach unsuitable for the development of reliable sensor materials. This limitation was overcome by grafting Nile Blue to a self-plasticized poly(n-butyl acrylate) matrix via an urea or amide linkage between the Nile Blue base structure and the polymer. Optode leaching experiments into methanol confirmed the successful covalent attachment of the two chromoionophores to the polymer matrix. Both polymerized Nile Blue derivatives have satisfactory pH response and appropriate optical properties that are suitable for use in ion-selective electrodes and optodes. Plasticizer-free Na⁺-selective microsphere sensors using the polymerized chromoionophores were fabricated under mild conditions with an in-house sonic microparticle generator for the measurement of sodium activities at physiological pH. The measuring range for sodium was found as 10⁻¹-10⁻⁴ M and 1-10⁻³ M, for Nile Blue derivatives linked via urea and amide functionalities, respectively, at physiological pH. The observed ion-exchange constants of the plasticizer-free microsphere were log K_exch = −5.6 and log K_exch = −6.5 for the same two systems, respectively. Compared with earlier Na⁺-selective bulk optodes, the fabricated optical sensing microbeads reported here have agreeable selectivity patterns, reasonably fast response times, and more appropriate measuring ranges for determination of Na⁺ activity at physiological pH in undiluted blood samples.     

Ammonia gas sensor based on electrosynthesized polypyrrole films

In this work, design and fabrication of micro-gas-sensors, polymerization and deposition of poly(pyrrole) thin films as sensitive layer for the micro-gas-sensors by electrochemical processing, and characterization of the polymer films by FTIR, X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM), are reported. The change in conductance of thin polymer layers is used as a sensor signal. The behaviours, including sensitivity, reproducibility and reversibility, to various ammonia gas concentrations ranging from 8 ppm to 1000 ppm are investigated. The influence of the temperature on the electrical response of the sensors is also studied. The experimental results show that these ammonia gas sensors are efficient since they are sensitive to ammonia, reversible and reproducible at room temperature.     

Fabrication of an ammonia gas sensor using inkjet-printed polyaniline nanoparticles

This work details the fabrication and performance of a sensor for ammonia gas analysis which has been constructed via the inkjet-printed deposition of polyaniline nanoparticle films. The conducting films were assembled on interdigitated electrode arrays and characterised with respect to their layer thickness and thermal properties. The sensor was further combined with heater foils for operation at a range of temperatures. When operated in a conductimetric mode, the sensor was shown to exhibit temperature-dependent analytical performance to ammonia detection. At room temperature, the sensor responded rapidly to ammonia (t₅₀ = 15 s). Sensor recovery time, response linearity and sensitivity were all significantly improved by operating the sensor at temperatures up to 80 °C. The sensor was found to have a stable logarithmic response to ammonia in the range of interest (1-100 ppm). The sensor was also insensitive to moisture in the range from 35 to 98% relative humidity. The response of the sensor to a range of common potential interferents was also studied.     

Properties of foam films stabilized with tetraethylammonium perfluorooctane-sulfonate

Properties of single foam films prepared with tetraethylammonium perfluorooctane-sulfonate (TAPOS) were studied. Film thickness was measured as a function of NH₄Cl concentration in the film forming solution. The dependence of the film disjoining pressure versus the film thickness (disjoining pressure isotherms) and the mean lifetime of the films were studied. The dependence of the film thickness on the electrolyte concentration showed the presence of an electrostatic double layer at the film surfaces. The electrostatic double layer component of the disjoining pressure was screened at a NH₄Cl concentration higher than 0.2 M where Newton black films (NBFs) of 6 nm thickness were formed. These films are bilayers of amphiphile molecules and contain almost no free water. The disjoining pressure isotherms of the foam films formed with 0.001 M TAPOS were measured at two different NH₄Cl concentrations (0.005 and 0.0005 M). The Deryaguin-Landau-Verwey-Overbeek (DLVO) theory describes well the isotherms with an electrostatic double layer potential of ∼140 mV. The mean lifetime, a measure of the stability of the NBFs, was measured depending on surfactant concentrations. The observation of NBF was possible above a minimum TAPOS concentration of 9.4 × 10⁻⁵ M. Above this concentration, the lifetime increases exponentially. The dependence of the film lifetime on surfactant concentration is explained by the theory for NBF-rupture by nucleation mechanism of formation of microscopic holes.     

Construction and performance characteristics of new ion selective electrodes based on carbon nanotubes for determination of meclofenoxate hydrochloride

This work offers construction and comparative evaluation the performance characteristics of conventional polymer (I), carbon paste (II) and carbon nanotubes chemically modified carbon paste ion selective electrodes (III) for meclofenoxate hydrochloride are described. These electrodes depend mainly on the incorporation of the ion pair of meclofenoxate hydrochloride with phosphomolybdic acid (PMA) or phosphotungestic acid (PTA). They showed near Nernestian responses over usable concentration range 1.0 × 10⁻⁵ to 1.0 × 10⁻² M with slopes in the range 55.15–59.74 mV (concentration decade)⁻¹. These developed electrodes were fully characterized in terms of their composition, response time, working concentration range, life span, usable pH and temperature range. The electrodes showed a very good selectivity for Meclo with respect to a large number of inorganic cations, sugars and in the presence of the degradation product of the drug (p-chloro phenoxy acetic acid). The standard additions method was applied to the determination of MecloCl in pure solution, pharmaceutical preparations and biological samples. Dissolution testing was also applied using the proposed sensors.     

Polyantimonic acid-based materials evaluated as moisture sensors at ambient temperature

Humidity sensors are in high demand for many applications, such as environmental monitoring and air and food quality control. Despite many inorganic and organic materials exhibit moisture sensing properties, the electrical response of many existing sensors is not stable along the time. Polyantimonic acid (PAA) is characterized by elevated proton conductivity and by high thermal stability: consequently, it is seen as promising proton conductor for usage in humidity sensing devices. In this work, for the first time, PAA-based bulk solid membranes were produced and tested as potential materials for relative humidity (RH) detection and their moisture sensitivity was evaluated. Two different amounts of binder were used for moulding the solid sensors: the ones with 10% of binder were designated as 90PAA, while the ones with 20% were named 80PAA. The structures of the solid samples were investigated by X-ray diffraction (XRD) technique, adsorption–desorption curves via Brunauer–Emmett–Teller (BET), scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) techniques. The electrical behaviour was examined at ambient temperature by electrical impedance spectroscopy in the entire relative humidity (RH) interval (0–100%) and in the frequency range of 40 Hz up to 60 MHz. Electrical response of the materials was correlated with the structural features of the membranes. Both 90PAA and 80PAA sensors showed total resistance 3 × 10⁵ and 3.5 × 10⁵ Ω at 10% RH, respectively. A linear decrease of the resistance on RH was observed in the range 30–90% RH for both sensors. The electrical response of the evaluated PAA-based sensors displays good repeatability and reproducibility: the ones with lower binder content showed higher moisture sensitivity as well as very good time stability over 1 year.

     

Development of a potassium-selective optode for hydroponic nutrient solution monitoring

Highly efficient and reliable plant growth such as that required in biological life support systems for future space-based missions can be better achieved with knowledge of ion concentrations within the hydroponic nutrient solution. This paper reports on the development and application of ion-selective bulk optodes to plant growth systems. Membranes for potassium-selective sensing are reported that have been tailored so that their dynamic range is centred on potassium activities within typical nutrient solution recipes. The developed sensors have been shown to exhibit a potassium activity measuring range from 0.134 to 117 mM at pH 6.0. These bulk optodes show full scale response on the order of several minutes. They show minimal interference to other cations and meet worst-case selectivity requirements for potassium monitoring in the considered half strength Hoagland solution. When continuously immersed in nutrient solution, these sensors demonstrated predicable lifetimes on the order of 50 h. The developed instrument for absorption-based measurements including light source, mini-spectrometer and optode probe is presented. Custom instrument control and monitoring software including a spectral normalization procedure, use of a dual-wavelength absorbance ratio technique and automatic adjustment for pH variation result in an instrument that is self-calibrating and one that can account for effects such as light source fluctuations, membrane thickness variations and a variety of other factors. The low mass, low volume nature of bulk optode sensing systems, make them a promising technology for future space-based plant production systems. Their low-cost and technology transfer potential suggest that they could provide terrestrial growers a new and reliable mechanism to obtain ion-selective knowledge of their nutrient solution, improving yields, reducing costs and aiding in compliance to continually more stringent environmental regulation.     

Immobilisation and assessment of aniline dyes for non-fluorescent pH sensing applications

The attachment of two aniline-based chromophores, Disperse Black 3 and Pararosaniline, to beaded controlled pore glass (CPG) and their testing as fibre optic based pH sensors is described. Synthetic methods for their attachment at specified loadings to CPG were developed. The Disperse Black 3 sensor displayed a rapid response time and a dynamic range between pH 1.0 and 2.5, while the Pararosaniline-bearing sensor gave an extremely slow response time but a large sensing range from pH 1 to 11.     

Sulfadiazine-selective determination in aquaculture environment: selective potentiometric transduction by neutral or charged ionophores

Solid-contact sensors for the selective screening of sulfadiazine (SDZ) in aquaculture waters are reported. Sensor surfaces were made from PVC membranes doped with tetraphenylporphyrin-manganese(III) chloride, α-cyclodextrin, β-cyclodextrin, or γ-cyclodextrin ionophores that were dispersed in plasticizer. Some membranes also presented a positive or a negatively charged additive. Phorphyrin-based sensors relied on a charged carrier mechanism. They exhibited a near-Nernstian response with slopes of 52 mV decade⁻¹ and detection limits of 3.91 × 10⁻⁵ mol L⁻¹. The addition of cationic lipophilic compounds to the membrane originated Nernstian behaviours, with slopes ranging 59.7-62.0 mV decade⁻¹ and wider linear ranges. Cyclodextrin-based sensors acted as neutral carriers. In general, sensors with positively charged additives showed an improved potentiometric performance when compared to those without additive. Some SDZ selective membranes displayed higher slopes and extended linear concentration ranges with an increasing amount of additive (always <100% ionophore). The sensors were independent from the pH of test solutions within 2-7. The sensors displayed fast response, always <15 s. In general, a good discriminating ability was found in real sample environment. The sensors were successfully applied to the fast screening of SDZ in real waters samples from aquaculture fish farms. The method offered the advantages of simplicity, accuracy, and automation feasibility. The sensing membrane may contribute to the development of small devices allowing in locus measurements of sulfadiazine or parent-drugs.     

Single crystal WO3 nanoflakes as quartz crystal microbalance sensing layer for ultrafast detection of trace sarin simulant

Tungsten oxide (WO₃) nanoflakes were synthesized, and characterized by scanning electron microscopy, transmission electron microscopy and X-ray diffraction. Thermogravimetry and X-ray photoelectron spectroscopy demonstrate the existence of strongly bound surface water molecules on the surface of tungsten oxide nanoflakes. WO₃ nanoflake functionalized quartz crystal microbalance sensors were fabricated, and firstly used for detection of trace sarin simulant, dimethyl methylphosphonate (DMMP). The sensors have better reproducibility and stability as well as much shorter response (30 s) and recovery time (73 s) than those functionalized by conventional hydrogen-bond acidic branched copolymers. The strongly bound surface water molecules on the surface of WO₃ nanoflakes are believed to play a key role in achieving such excellent DMMP sensing characteristics.     

Highly sensitive and ultrafast response surface acoustic wave humidity sensor based on electrospun polyaniline/poly(vinyl butyral) nanofibers

Polyaniline (PANi) composite nanofibers were deposited on surface acoustic wave (SAW) resonator with a central frequency of 433 MHz to construct humidity sensors. Electrospun nanofibers of poly(methyl methacrylate), poly(vinyl pyrrolidone), poly(ethylene oxide), poly(vinylidene fluoride), poly(vinyl butyral) (PVB) were characterized by scanning electron microscopy, and humidity response of corresponding SAW humidity sensors were investigated. The results indicated that PVB was suitable as a matrix to form nanofibers with PANi by electrospinning (ES). Electrospun PANi/PVB nanofibers exhibited a core–sheath structure as revealed by transmittance electron microscopy. Effects of ES collection time on humidity response of SAW sensor based on PANi/PVB nanofibers were examined at room temperature. The composite nanofiber sensor exhibited very high sensitivity of ∼75 kHz/%RH from 20 to 90%RH, ultrafast response (1 s and 2 s for humidification and desiccation, respectively) and good sensing linearity. Furthermore, the sensor could detect humidity as low as 0.5%RH, suggesting its potentials for low humidity detection. Attempts were done to explain the attractive humidity sensing performance of the sensor by considering conductivity, hydrophilicity, viscoelasticity and morphology of the polymer composite nanofibers.     

All-solid-state potentiometric sensors for ascorbic acid by using a screen-printed compatible solid contact

The development of all-solid-state potentiometric ion selective electrodes for monitoring of ascorbic acid, by using a screen-printed compatible solid contact is described. The applied methodology is based on the use of PVC membrane modified with some firstly-tested ionophores (triphenyltin(IV)chloride, triphenyltin(IV)hydroxide and palmitoyl-l-ascorbic acid) and a novel one synthesized in our laboratory (dibutyltin(IV) diascorbate). Synthesis protocol and some preliminary identification studies are given. A conductive graphite-based polymer thick film ink was used as an internal solid contact between the graphite electrode and the PVC membrane. The presence and the nature of the solid contact (plain or doped with lanthanum 2,6-dichlorophenolindophenol (DCPI)) seem to enhance the analytical performance of the electrodes in terms of sensitivity, dynamic range, and response time. The analytical performance of the constructed electrodes was evaluated with potentiometry, constant-current chronopotentiometry and electrochemical impedance spectroscopy (EIS). The interference effect of various compounds was also tested. The potential response of the optimized Ph₃SnCl-based electrode was linear against ascorbic acid concentration range 0.005-5.0 mM. The applicability of the proposed sensors in real samples was also tested. The detection limit was 0.002 mM ascorbic acid (50 mM phosphate, pH 5 in 50 mM KCl). The slope of the electrodes was super-Nernstian and pH dependent, indicating a mechanism involving a combination of charge transfer and ion exchange processes. Fabrication of screen-printed ascorbate ISEs has also been demonstrated.     

Mesoporous carbon amperometric glucose sensors using inexpensive,commercial methacrylate-based binders

Two ordered, soft-templated mesoporous carbon powders with cubic and hexagonal framework structure and four different commercial, low cost methacrylate-based polymer binders with widely varying physical properties are investigated as screen printed electrodes for glucose sensors using glucose oxidase and ferricyanide as the mediator. Both the chemistry and concentration of the binder in the electrode formulation can significantly impact the performance. Poly(hydroxybutyl methacrylate) as the binder provides hydrophilicity to enable transport of species in the aqueous phase to the carbon surface, but yet is sufficiently hydrophobic to provide mechanical robustness to the sensor. The current from the mesoporous carbon electrodes can be more than an order of magnitude greater than for a commercial printed carbon electrode (Zensor) with improved sensitivity for model glucose solutions. Even when applying these sensors to rabbit whole blood, the performance of these glucose sensors compares favorably to a standard commercial glucose meter with the lower detection limit of the mesoporous electrode being approximately 20 mg dL⁻¹ despite the lack of a separation membrane to prevent non-specific events; these results suggest that the small pore sizes and high surface areas associated with ordered mesoporous carbons may effectively decrease some non-specific inferences for electrochemical sensing.     

Response surface methodology for the modelling of copper removal from aqueous solutions using micellar-enhanced ultrafiltration

Response surface methodology (RSM) was used to study the cumulative effect of the various parameters, namely surfactant (sodium dodecyl sulphate (SDS), anionic) concentration, pH, and surfactant/metal molar ratio and to optimise the process conditions for the maximum removal of copper from aqueous solutions via micellar-enhanced ultrafiltration (MEUF). For obtaining the mutual interaction between the variables and optimising these variables, a central composite design (CCD) by use of response surface methodology was employed. The analysis of variance (ANOVA) of the quadratic model demonstrated that the model was highly significant. The model was statistically tested and verified by experimentation. Values of pH at the range of ca. 7.5 were very successful for the separation. The maximum rejection coefficient of 98.4% was obtained for the following optimal conditions: SDS/Cu²⁺ molar ratio *r = 7.85, *pH 7.36, *C_surf = 6.82 g/l SDS. A modification of micellar-enhanced ultrafiltration for the removal of copper from aqueous solutions was studied by the implementation of sodium dodecyl sulphate–polyethylene glycol (PEG) aggregates. A full factorial design (FFD) was employed for studying the effect of molar ratio of surfactant/metal, pH and mass ratio of surfactant/polymer at a constant concentration of surfactant equal to 5 g/l. The comparison of the two systems in the region of their common factors showed that the addition of polyethylene glycol caused a slight increase in rejection coefficient of copper but also could function as ‘scavenger’ for surfactant species.     

Development of trichloroacetic acid sensor based on molecularly imprinted polymer membrane for the screening of complex mixture of haloacetic acids in drinking water

This work shows developing conductometric sensor based on molecularly imprinted polymer (MIP) for the screening of complex mixture of haloacetic acids (HAAs) in drinking water. The recognition of the HAAs was achieved by trichloroacetic acid (TCAA)-imprinted polymers synthesised from the copolymerization of 4-vinylpyridine (4-VPD) and ethylene glycol dimethacrylate (EDMA) in the presence of the TCAA template in acetonitrile, either by bulk polymerization (BP) method or by a multi-step swelling polymerization (MSP) method. TCAA-imprinted polymer of both methods was tested for re-binding with the template and its analogs. It was found that these polymers could bind selectively to the template molecule and HAA derivatives. HAA measurements were carried out by the application of the polyvinyl chloride membrane fabricated with TCAA-imprinted polymer on conductometric sensors. The technological parameters (operating frequency, membrane composition, ionic strength and medium pH) for the sensors were identified and optimised in respect to the response to TCAA, using sensor fabricating with BP-based MIP as a model. The selectivity of the sensors constructed with MIPs made by either that of the two imprinting methods was also investigated, which the influence of the method of imprinting on the binding strength and selectivity of the recognition element embedded in sensor was observed. The sensors showed high sensitivity and selectivity for the response toward TCAA, the sensor modified with MSP-based MIP being better. In addition, the sensors, particularly when was constructed with MSP-based MIP exhibited good cross-reactivities with a wide range of HAAs, which is useful for the screening of the group of HAA usually present in chlorinated water in complex mixtures. Thus, the sensor modified with MSP-based MIP was chosen for analytical application. The calibration of this sensor was determined, showing the good linear graphs (R²>0.970) for HAAs over the concentration range of 25-1000 μg/l and the detection limit of each HAA in the range 0.2-5.0 μg/l. Moreover, the results in real analysis of the sensor indicate the simplicity and reliability of the method. The present work demonstrated that the sensor based on TCAA-imprinted polymer is a fast and sensitive screening method of HAAs in drinking water.