Raman characterization of orientation in poly(lactic acid) films

Poly(lactic acid) is a new biopolymer material which is marketed by Cargill Dow Polymers under the tradename Nature Works*. One major application for this material is biaxially oriented films for food packaging because it possesses excellent barrier for flavor constituents, deadfold and heat sealability. Shrinkage must be minimized when the film is heat sealed for these applications and, therefore, characterization of the orientation of the amorphous phase of PLA films is necessary. Raman spectroscopy methodology has been developed to quantify orientation in PLA films. Bands were assigned to crystalline and amorphous phases of PLA such that orientation in both phases could be monitored. Raman depolarization ratios were used to characterize uniaxial systems but were insufficient for most biaxial draws. A new phenomenon for oriented films involving Raman band shifts was observed in these systems, and was shown to be capable of determining orientation, even for symmetrical biaxially drawn films. The origin of these shifts, as well as their use for the quantification of orientation will be discussed. Further, since the line widths of the bands could be used to quantify crystallinity, both crystallinity and orientation could be determined with one measurement.     

Cooperativity length evolution during crystallization of poly(lactic acid)

Effects of stereoregularity and crystallization mode on the amorphous phase dynamics are investigated for poly(lactic acid) PLA. An isothermal crystallization from the melt and a cold crystallization are imposed. For each PLA, the cold crystallization leads to the appearance of a less perfect crystalline phase and to an important rigid amorphous fraction RAF content (35%), although only 10% of RAF is generated after crystallization from the melt. Temperature Modulated Differential Scanning Calorimetry is used to determine the Cooperative Rearranging Regions (CRR) size at the glass transition temperature in the mobile amorphous phase MAP. It is shown that the CRR size in the MAP is not modified by the appearance and the spherulite growth. For the intra-spherulite MAP, a confining effect is evidenced, causing an amorphous phase thickness decrease during crystallization, and inducing a drastic CRR size reduction.     

Synthesis and characterization of poly(l-lactic acid) reinforced by biomesogenic units

To increase the thermal and mechanical properties of poly(l-lactic acid) (PLA), a nontoxic biomesogen PFBH derived from ferulic acid (FA), 4-hydroxybenzoic acid (HBA) and 1,6-hexanediol (HD) was introduced into the PLA backbones by solution polymerization of PLA, PFBH and chain linker hexamethylene diisocyanate (HDI). The content of PFBH was varied from 0 to 30 mol% so that the effects of the biomesogen content on the thermal and physical properties, morphological textures and enzymatic degradation were examined, respectively. The synthesized materials were characterized by means of differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), wide angle X-ray diffraction (WAXD), polarizing light microscopy (PLM) and mechanical property measurements. It was found that introducing biomesogenic units could increase the thermal stability and reinforce the elastic properties, while reduced the melting temperature, the degree of crystallinity and the enzymatic degradation rate. The nontoxicity and biocompatibility of degradation would make the products promising candidates for medical applications in the area of tissue engineering.     

Form birefringence dispersion of an oriented poly(styrene-b-isoprene) triblock copolymer (SIS) with cylindrical texture

Summary We applied Wiener's theory to calculate form birefringence dispersion of an oriented block copolymer from dispersion formulas of refractive indices of bulk polymers corresponding to the blocks forming the microdomains. The nearly perfect concordance of the measured birefringence dispersion with the calculated one seems to indicate an almost complete lack of molecular orientation inside microdomains. The importance of birefringence dispersion involves modification of interference spectrum in white light. This phenomenon may induce errors when ultilizing a Berek compensator for birefringence measurements.With 16 figures     

Biodegradable poly(lactic acid)/chitosan-modified montmorillonite nanocomposites: Preparation and characterization

In this study, the biodegradable poly(lactic acid) (PLA)/montmorillonite (MMT) nanocomposites were successfully prepared by the solution mixing process of PLA polymer with organically-modified montmorillonite (m-MMT), which was first treated by n-hexadecyl trimethyl-ammonium bromide (CTAB) cations and then modified by biocompatible/biodegradable chitosan to improve the chemical similarity between the PLA and m-MMT. Both X-ray diffraction data and transmission electron microscopy images of PLA/m-MMT nanocomposites indicate that most of the swellable silicate layers were disorderedly intercalated into the PLA matrix. Mechanical properties and thermal stability of the PLA/m-MMT nanocomposites performed by dynamic mechanical analysis and thermogravimetric analysis have significant improvements in the storage modulus and 50% loss in temperature when compared to that of neat PLA matrix. The degradation rates of PLA/m-MMT nanocomposites are also discussed in this study.     

Stabilization of poly(lactic acid) by polycarbodiimide

Polycarbodiimide (CDI) was used to improve the thermal stability of poly(l-lactic acid) (PLA) during processing. The properties of PLA containing various amounts of CDI were characterized by GPC, DSC, rheology, and tensile tests. The results showed that an addition of CDI in an amount of 0.1-0.7 wt% with respect to PLA led to stabilization of PLA at even 210 °C for up to 30 min, as evidenced by much smaller changes in molecular weight, melt viscosity, and tensile strength and elongation compared to the blank PLA samples. In order to examine the possible stabilization mechanism, CDI was reacted with water, acetic acid, l-lactic acid, ethanol and low molecular weight PLA. The molecular structures of the reaction products were measured with FTIR. The results showed that CDI could react with the residual or newly formed moisture and lactic acid, or carboxyl and hydroxyl end groups in the PLA samples, and thus hamper the thermal degradation and hydrolysis of PLA.     

Silkworm silk/poly(lactic acid) biocomposites: Dynamic mechanical, thermal and biodegradable properties

Silkworm silk/Poly(lactic acid) (silk/PLA) biocomposites with potential for environmental engineering applications were prepared by using melting compound methods. By means of Dynamic mechanical analysis (DMA), Differential scanning calorimetry (DSC), Thermogravimetric analysis (TGA), Coefficient of thermal expansion test, Enzymatic degradation test and Scanning electron microscopy (SEM), the effect of silk fiber on the structural, thermal and dynamic mechanical properties and enzymatic degradation behavior of the PLA matrix was investigated. As silk fiber was incorporated into PLA matrix, the stiffness of the PLA matrix at higher temperature (70-160 °C) was remarkably enhanced and the dimension stability also was improved, but its thermal stability became poorer. Moreover, the presence of silk fibers also significantly enhanced the enzymatic degradation ability of the PLA matrix. The higher the silk fiber content, the more the weight loss.     

Influences of poly(lactic acid)‐grafted carbon nanotube on thermal,mechanical, and electrical properties of poly(lactic acid)

Poly(lactic acid)‐grafted multiwalled carbon nanotubes (MWNT‐g‐PLA) were prepared by the direct melt‐polycondensation of L ‐lactic acid with carboxylic acid‐functionalized MWNT (MWNT‐COOH) and then mixed with a commercially available neat PLA to prepare PLA/MWNT‐g‐PLA nanocomposites. Morphological, thermal, mechanical, and electrical characteristics of PLA/MWNT‐g‐PLA nanocomposites were investigated as a function of the MWNT content and compared with those of the neat PLA, PLA/MWNT, and PLA/MWNT‐COOH nanocomposites. It was identified from FE‐SEM images that PLA/MWNT‐g‐PLA nanocomposites exhibit good dispersion of MWNT‐g‐PLA in the PLA matrix, while PLA/MWNT and PLA/MWNT‐COOH nanocomposites display MWNT aggregates. As a result, initial moduli and tensile strengths of PLA/MWNT‐g‐PLA composites are much higher than those of neat PLA, PLA/MWNT, and PLA/MWNT‐COOH, which stems from the efficient reinforcing effect of MWNT‐g‐PLA in the PLA matrix. In addition, the crystallization rate of PLA/MWNT‐g‐PLA nanocomposites is faster than those of neat PLA, PLA/MWNT, and PLA/MWNT‐COOH, since MWNT‐g‐PLA dispersed in the PLA matrix serves efficiently as a nucleating agent. It is interesting that, unlike PLA/MWNT nanocomposites, surface resistivities of PLA/MWNT‐g‐PLA nanocomposites did not change noticeably depending on the MWNT content, demonstrating that MWNTs in PLA/MWNT‐g‐PLA are wrapped with the PLA chains of MWNT‐g‐PLA. Copyright © 2008 John Wiley & Sons, Ltd.     

Bionanocomposite based on cellulose nanowhisker from oil palm biomass-filled poly(lactic acid)

Cellulose nanowhiskers (CNW) extracted from plant fibers exhibit remarkable properties that make them suitable for use in the development of bionanocomposites. CNW have demonstrated the capability to enhance the properties of a polymer matrix at low filler loading. In this study, poly (lactic acid) (PLA) bionanocomposites were prepared using the solution casting technique, by incorporating the PLA with the CNW obtained from an oil palm empty fruit bunch (OPEFB). Fourier transform infrared spectroscopy showed no significant changes in the PLA peak positions, which indicates that incorporating the CNW into the PLA did not result in any significant changes in the chemical structure of the PLA. Thermogravimetric analysis, on the other hand, revealed that the bionanocomposites (PLA-CNW) had better thermal stability than the pure PLA. The tensile strength of PLA-CNW increased by 84% with the addition of 3 parts of CNW per hundred resins (phr), and decreased thereafter. Moreover, a linear relationship was observed between the Young's modulus and CNW loading. Elongation at break, however, decreased with the addition of 1-phr CNW, and remained constant with further addition. Transmission electron microscopy revealed that agglomeration of CNW occurred at 5-phr loading, consistent with the tensile strength results. Overall, the CNW obtained from OPEFB can enhance the tensile and the thermal properties of bionanocomposites.     

Porous scaffolds based on cross-linking of poly(L-glutamic acid)

Porous scaffolds based on water-soluble PLGA and CS were prepared. The pores were verified to be alveolate, uniform and continuous. The effects of freezing temperature, freeze-drying time, solid content and molecular weight of reactants on the pore structure of the scaffolds were studied. The scaffold morphology could be adjusted by changing the freezing temperature and solid content of reacting polymer. Their degradation rate can be adjusted by changing the proportion of PLGA and CS. The porosity of scaffolds was higher than 90% and the high swelling ratio showed that these scaffolds had excellent hydrophilic performance. The in vitro culture of chondrocytes indicates that the obtained PLGA/CS porous scaffolds are very promising biomaterials for tissue engineering applications.     

Chemical modification of nanocrystalline cellulose for improved interfacial compatibility with poly(lactic acid)

1. Download high-res image (220KB)
2. Download full-size image

     

Modification of porous poly(ether sulfone) membranes by low‐temperature CO2‐plasma treatment

A general method of modifying the entire cross section of porous poly(ether sulfone) membranes with a low‐temperature CO₂‐plasma treatment is reported. Both surfaces of the membranes are highly hydrophilic, with a water drop on the surface disappearing in less than 1 s, even 6 months after plasma treatment. This high hydrophilicity of both membrane surfaces results from the incorporation of hydrophilic functionalities, as evidenced by Fourier transform infrared spectroscopy and X‐ray photoelectron spectroscopy. The incorporation of these hydrophilic functionalities takes place primarily during plasma treatment, with some incorporation of atmospheric oxygen and nitrogen immediately upon exposure to air. Scanning electron microscopy shows that the membrane surface is covered by a thin, white layer that is likely the result of etching and redeposition of sputtered surface fragments. An increase in the water bubble point and glass‐transition temperature is also observed for CO₂‐plasma‐treated membranes. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2473–2488, 2002     

Chemical modification of poly(lactic acid) and its use as matrix in poly(lactic acid) poly(butylene adipate-co-terephthalate) blends

Poly(lactic acid), PLA, was chemically modified with maleic anhydride (MA) by reactive extrusion. The effect of this modification on molar mass (MM) and acidity was assessed by means of size-exclusion chromatography (SEC) and titration, respectively. PLA MM decreased in the presence of MA solely and of MA and peroxide. Reduction in MM was monitored by the increase in acidity. PLA blends containing poly(butylene adipate-co-terephthalate) (PBAT) were prepared through different mixing protocols, PLA/PBAT, PLA-g-MA/PBAT and PLA/PBAT/MA/peroxide (PLA/PBAT in situ). SEC results and rheological properties revealed reduction in MM and viscosity of the modified blends. PLA/PBAT presented increase in MM and bimodal MM distribution. The calculated interfacial tension was significantly lower for the modified blends, despite the lower average particle area of PLA/PBAT. Surprisingly, the modified blends presented higher yield strength than that predicted by the rule of mixtures, which might indicate interfacial reactions.     

Conjugation of bioactive groups to poly(lactic acid) and poly[(lactic acid)-co-(glycolic acid)] films

A novel PLA-based polymer containing reactive pendent ketone or hydroxyl groups was synthesized by the copolymerization of L-lactide with epsilon-caprolactone-based monomers. The polymer was activated with NPC, resulting in an amine-reactive polymer which was then cast into thin polymeric films, either alone or as part of a blend with PLGA, before immersion into a solution of the cell adhesion peptide GRGDS in PBS buffer allowed for conjugation of GRGDS to the film surfaces. Subsequent 3T3 fibroblast cell adhesion studies demonstrated an increase in cellular adhesion and spreading over films cast from unmodified PLGA. Hence the new polymer can be used to obtain covalent linkage of amine-containing molecules to polymer surfaces.     

Characterisation of multi-extruded poly(lactic acid)

The effect of multiple (up to 10 times) extrusion of polylactide on its mechanical properties (determined by a static tension test), Charpy impact strength, melt flow rate, phase transition temperatures, degradation temperature, and permeability of water vapour and oxygen is presented. It was found that, with raising the number of the extrusion cycles, the tensile strength at break slightly diminished and the impact strength clearly decreased, while the melt flow rate and water vapour and oxygen transmission rates steadily increased. Variation of the number of extrusion cycles did not affect the glass transition temperature, whereas it did cause a lowering of the cold crystallisation temperature and slight diminishing of the melting point. The presented results indicate that PLA technological waste is suitable to be reused as an additive to a neat polymer.     

XPS and wettability characterization of modified poly(lactic acid) and poly(lactic/glycolic acid) films

Poly(lactic acid) (PLA) and poly(lactic/glycolic acid) copolymers (PLGA) are biodegradable drug carriers of great importance, although successful pharmaceutical application requires adjustment of the surface properties of the polymeric drug delivery system to be compatible with the biological environment. For that reason, reduction of the original hydrophobicity of the PLA or PLGA surfaces was performed by applying a hydrophilic polymer poly(ethylene oxide) (PEO) with the aim to improve biocompatibility of the original polymer. PEO-containing surfaces were prepared by incorporation of block copolymeric surfactants, poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (Pluronic), into the hydrophobic surface. Films of polymer blends from PLA or PLGA (with lactic/glycolic acid ratios of 75/25 and 50/50) and from Pluronics (PE6800, PE6400, and PE6100) were obtained by the solvent casting method, applying the Pluronics at different concentrations between 1 and 9.1% w/w. Wettability was measured to monitor the change in surface hydrophobicity, while X-ray photoelectron spectroscopy (XPS) was applied to determine the composition and chemical structure of the polymer surface and its change with surface modification. Substantial reduction of surface hydrophobicity was achieved on both the PLA homopolymer and the PLGA copolymers by applying the Pluronics at various concentrations. In accordance with the wettability changes the accumulation of Pluronics in the surface layer was greatly affected by the initial hydrophobicity of the polymer, namely, by the lactide content of the copolymer. The extent of surface modification was also found to be dependent on the type of blended Pluronics. Surface activity of the modifying Pluronic component was interpreted by using the solubility parameters.     

Molecular orientation in poly(vinyl chloride) studied by Raman spectroscopy and birefringence measurements

The ratios of the intensities of Raman scattering in the C? CI stretching region for eight combinations of sample orientation and directions of polarization of incident and scattered light have been measured for 15 samples of poly(vinyl chloride) (PVC) containing 0, 5, 10, 15 or 20 pph dioctyl sebacate (DOS) plasticizer which had been drawn uniaxially at 22, 70, 75, 80, or 90°C to draw ratios in the range 1–4.5. The birefringences of the samples were also measured. The Raman data were analyzed to give 〈P₂(cosθ)〉_cryst and 〈P₄(cosθ)〉_cryst, the values of the second- and fourth-order Legendre polynomials in cosθ averaged over the distribution of orientations of the crystallites, where θ is the angle between the c axis of a typical crystallite and the draw direction. Comparison of 〈P₂(cosθ)〉_cryst with the birefrigence showed that the crystallites are more highly oriented than the noncrystalline material in samples containing the higher amounts of plasticizer drawn at the higher temperatures. A value of 13.0 × 10^?3 was deduced for the birefringence of fully oriented PVC. The values of 〈P₄(cosθ)〉_cryst for a given 〈P₂(cosθ)〉_cryst were found to be higher than predicted by calculations based on two simple models, the pseudoaffine rigid-rod rotation model and the affine rubber elasticity model.