Effect of the silica content on the physico-chemical and relaxation properties of hybrid polymer/silica nanocomposites of P(EMA-co-HEA)

Poly(ethyl methacrylate-co-hydroxyethyl acrylate) 70/30 %wt/silica, P(EMA-co-HEA)/SiO₂, nanocomposites, with silica contents ranging from 0 to 30 %wt, were synthesized and studied as promising candidate materials for the synthetic matrix of scaffolds for bone substitutes or dentin regeneration. The physico-chemical properties of the hybrids were studied by calorimetry and by contact angle measurements on the surfaces. The dynamic-mechanical and compression properties were analysed. Intermediate silica contents in the range from 10 to 20 %wt of silica rendered co-continuous interpenetrated structures, in which silica produced a reinforcing effect in the polymeric matrix and at the same time conferred bioactivity to the surfaces by improving surface wettability, making these hybrids appropriate for the proposed application. On the contrary, silica percentages below 10 %wt formed disconnected inorganic aggregates at the nanoscale dispersed in the copolymer matrix, which did not modify significantly the copolymer properties. Silica contents above 20 %wt formed denser inorganic networks with few terminal silanol groups available at the surfaces, much more rigid and hardly manageable samples.     

Polymer-silica nanocomposites prepared by sol-gel technique: Nanoindentation and tapping mode AFM studies

Polymer-silica nanocomposites based on poly(2-hydroxyethyl acrylate) (PHEA) have been prepared by the simultaneous polymerization of the organic and the silica phases in a sol-gel process with the silica precursor tetraethyl orthosilicate (TEOS). The structure of this system is investigated using atomic force microscopy (AFM) in the tapping mode and in nanoindentation experiments. The structure of the PHEA/silica hybrids strongly depends on the ratio of both components in the system. For silica weight fractions lower than 0.15, the system consists of aggregated silica particles dispersed in the organic matrix; above that concentration of silica the structure is co-continuous with that of the organic matrix, similarly to two interpenetrated networks.     

The interaction between TEOS and some polyols

Hybrid organic-inorganic materials, silica – polyols (ethylene-glycol – EG; 1,2 propane diol – 1,2PG; 1,3 propane diol – 1,3PG and glycerol – GL), were prepared by a sol-gel process starting from tetraethylorthosilicate (TEOS) and polyols, in acid catalysis. The resulting materials were studied by thermal analysis (in air and nitrogen), FTIR and solid state ²⁹Si-NMR spectroscopy. These techniques evidenced the presence of polyols in the silica matrix both hydrogen bounded and chemically bounded in the silica network. The thermal analysis proves to be the most appropriate technique to evidence the organic chains linked in the matrix network and to follow the thermal evolution of the gels to the SiO₂ matrix.     

Thermal transitions and dynamics in nanocomposite hydrogels

Hydrogels based on nanocomposites of statistical poly(hydroxyethyl acrylate-co-ethyl acrylate) and silica, prepared by simultaneous copolymerization and generation of silica nanoparticles by sol?Cgel process at various copolymer compositions and silica contents, characterized by a fine dispersion of filler, were investigated with respect to glass transition and polymer dynamics by dielectric techniques. These include thermally stimulated depolarization currents and dielectric relaxation spectroscopy, covering together broad ranges of frequency and temperature. In addition, equilibrium water sorption isotherms were recorded at room temperature (25?°C). Special attention was paid to the investigation of effects of silica on glass transition, polymer dynamics (secondary ?? and ?? _sw relaxations and segmental ?? relaxation), and electrical conductivity in the dry systems (xerogels) and in the hydrogels at various levels of relative humidity/water content. An overall reduction of molecular mobility is observed in the nanocomposite xerogels, in particular at high silica contents. Analysis of the results and comparison with previous work on similar systems enable to discuss this reduction of molecular mobility in terms of constraints to polymeric motion imposed by interfacial polymer?Cfiller interactions and by the formation of a continuous silica network interpenetrated with the polymer network at filler contents higher than about 15?wt%.     

Preparation of nonwoven polyimide/silica hybrid nanofiberous fabrics by combining electrospinning and controlled in situ sol-gel techniques

A controlled in situ sol-gel synthesis combined with the electrospinning technique and postspun imidization was applied in the fabrication of polyimide/silica hybrid nonwoven nanofiberous fabrics with excellent thermal and mechanical performance. The nanofiberous fabrics were prepared by electrospinning of the solution of tetraethoxysilane (TEOS) and polyamic acid (PAA). The different silica contents in the fabrics were achieved by varying the amount of TEOS while fitting the solid content of PAA. The final polyimide/silica fabrics was obtained after imidization of PAA and gelation of silica phase simultaneously accomplished through a step-wise heating process. Some specific IR techniques and other characterizations indicated the successful incorporation of the silicon dioxide (SiO₂) into the PI matrix and the relatively even distribution of the SiO₂ in the fabrics. An increase of 133 °C in the decomposition temperature and 4-fold enhancement of the ultimate tensile strength were achieved for the hybrids with a 6.58 wt.% of SiO₂ content, compared to the pure PI fabric. The excellent performance could be attributed to the good compatibility between the polyimide and silica, and good adhesion among the fibers, which resulted from the controlled TEOS hydrolysis and the simultaneous imidization and gelation process.     

Polyacrylate/silica nanocomposite materials prepared by sol-gel process

Polyacrylate/silica nanocomposite was prepared by sol-gel process via in situ emulsion polymerization. The influence of the synthetic conditions, such as the ratio of different monomers and the contents of tetraethoxysilane (TEOS), γ-methacryloxypropyltrimethoxysilane (Z-6030), diethanolamine (DAM) and ammonium persulfate (APS) on the physical mechanical properties of polyacrylate/silica nanocomposite was investigated in details. Dynamics Laser Scattering (DLS) indicated that the average diameter of the polyacrylate/silica latex particles (177 nm) was bigger than that of the pure polyacrylate latex particles (105.3 nm), but the ζ potential of polyacrylate/silica was decreased respectively in contrast to that of the polyacrylate. Differential Scanning Calorimeters (DSC) analysis confirmed that the glass transition temperature of polyacrylate/nano-SiO₂ (T_g = −24 °C) was higher than that of polyacrylate (T_g = −36 °C). UV analysis showed that the UV absorbency of polyacrylate/silica was improved evidently in contrast to that of polyacrylate.     

Preparation and photophysics of polyimide/silica organic/inorganic hybrid composites

In this work, polyimide/silica hybrid composites were prepared by the sol-gel reaction of tetraethoxysilane(TEOS) and the thermal imidization of poly(amic acid) from 3,3′,4,4′-biphenyltetracarboxylic dianhydride(BPDA) and 4,4′-oxydianiline(ODA), and their photophysical properties were investigated using a fluorescence spectroscopy. It was found that the intrinsic fluorescence of poly(4,4′-oxydiphenylene-3,3′4,4′-biphenyltetracarboximide)(BPDA-ODA) such as emission intensity and emission wavelength depends strongly on the changes in the molecular conformations during the sol-gel reaction and the thermal imidization. In conclusion, we found that the fluorescence spectroscopy can provide an insight into how the intermolecular or intramolecular interaction of polyimide in the hybrid composite system is affected by the silica contents, depending on the sample states.     

Encapsulation of Organic Pigment Particles with Silica via Sol-Gel Process

This paper presented a novel preparation method of silica coated organic pigment. In this approach, the surfaces of the organic pigment were first orderly modified by poly(sodium 4-styrenesulfonate) (PSS) and poly(diallyldimethylammonium chloride) (PDADMAC), then coated by silica via sol-gel process of tetraethylorthosilicate (TEOS). The results showed that PVP, pH value, water and TEOS contents had significant influence on the morphology of the silica encapsulated organic pigment. Organic pigments coated silica by this approach could scatter UV ray with wavelength less than 270 nm, and this scattering property increased with more silica coated.     

Preparation and properties of amino-terminated anionic waterborne-polyurethane-silica hybrid materials through a sol-gel process in the absence of an external catalyst

A series of polymer-silica hybrid materials consisting of amino-terminated anionic waterborne-polyurethane (WPU) and inorganic silica particles have been prepared through a sol-gel process in the absence of an external catalyst. Typically, amino-terminated anionic WPU was first synthesized from polycaprolactone, dimethylol propionic acid, and 4,4′-methylenebis(cyclohexyl isocyanate) with specific molar ratios, followed by further reaction with triethylamine and triethylene tetramine to give as-prepared WPU. The WPU obtained was characterized by FTIR spectroscopy and gel permeation chromatography. Subsequently, a series of hybrid materials with different silica contents were prepared by performing sol-gel reactions with tetraethyl orthosilicate (TEOS) in an amino-terminated WPU matrix without the addition of an external catalyst. This was followed by examination by transmission electron microscopy and ²⁹Si solid-state NMR. The terminated primary amine groups attached to the as-prepared WPU chains functioned as an internal base catalyst for the sol-gel process of TEOS. The effect of composition on the thermal stability, mechanical strength, surface wettability, and optical clarity of the hybrid materials was evaluated by the thermogravimetric analysis, dynamic mechanical analysis, contact angle measurement, and UV-visible transmission spectroscopy, respectively.     

Synthesis and micromechanical properties of flexible, self-supporting polymer-SiO2 nanofilms

Large-scale, self-supporting ultrathin films composed of an elastomeric polyacrylate network interpenetrated by a silica (SiO2) network were synthesized and characterized. The organic network was first photopolymerized and the silica structure was subsequently developed in situ in the preformed organic gel. Composition and morphology of the hybrid interpenetrated network (IPN) nanofilms were characterized by infrared spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy and compared with the case of zirconia (ZrO2) hybrid IPN reported earlier. Young modulus, ultimate tensile strength, and ultimate tensile elongation were determined for different organic/inorganic molar ratios and give some insights on how the composition of the nanofilms influence their robustness and self-supporting properties.     

Preparation and properties of polybenzoxazole-silica nanocomposites via sol-gel process

A novel organic/inorganic hybrid material has been prepared through the sol-gel process. A high temperature polymer, polybenzoxazole (PBO), was chosen as the organic phase due to its inherent low dielectric constant and low water absorption. The inorganic phase was generated via sol-gel reaction from a silica precursor, phenyltriethoxysilane (PTEOS). Due to the hydroxyl groups in the PBO precursor backbone and the water release during the cyclization of the precursor, the sol-gel reaction proceeded without the addition of water and any catalyst. After curing at 350 °C, we obtained the PBO/silica nanocomposites. From TEM and SEM photographs, the silica particles dispersed in the PBO matrix were nano-sized. With an addition of 100 wt% of PTEOS, the T_g of PBO was increased 35 °C. The dielectric constant of the hybrid materials increased with the increasing amount of PTEOS.     

Silica reinforcement of epoxidized natural rubber by the sol-gel method

The sol-gel technique was employed to prepare silica-reinforced vulcanizates using tetraethylorthosilicate (TEOS) and epoxidized natural rubber (ENR). The rubber was first precured with 3-aminopropyltriethoxysilane (APS) by heat pressing at 180°C for a range of cure time. The resultant rubber sheets or vulcanizates were swelled in TEOS, and subsequently subjected to a sol-gel reaction in butylamine aqueous solution. Hydrolysis and condensation of the TEOS resulted in the formation of silica particles in the rubber network yielding silica-contained vulcanizates. Silica content as high as 28% and TEOS-to-silica conversion of over 60% were observed. When prepared under certain reaction conditions, the sol-gel vulcanizates obtained were more rigid and stronger than a typical sulfur-cured ENR vulcanizate that contained comparable amount of silica. Comparative stress-strain and dynamic mechanical property analysis suggest that chemicals bond are formed between the silica particles and the rubber network in the ENR-APS-sol-gel vulcanizate. Thus, the in situ silica reinforcement of ENR was successfully established.On leave from School of Industrial Technology, University Sains Malaysia, Minden, 11800, Penang, Malaysia.     

Silica-titania sol-gel hybrid materials: synthesis, characterization and potential application in solid phase extraction

The biphenilaminepropylsilica and biphenilaminepropylsilicatitania were synthesized by sol-gel method, in two steps: (a) biphenylamine reacts with chloropropyltrimethoxysilane and (b) the product of reaction was polycondensed with tetraethylorthosilicate (TEOS) or TEOS and titanium isopropoxide. The sol-gel materials were characterized using infrared spectroscopy and N₂ adsorption-desorption isotherms and they were employed as sorbents for carcinogenic N-containing compound retention, in aqueous solution, using the SPE technique. The N-containing compounds adsorption was influenced by the titania presence and the sorption process seems to happen in the pores with higher organic density.     

An investigation on structure and texture of silica-magnesia xerogels

Silica-magnesia xerogels were prepared by reacting tetraethoxysilane (TEOS) and magnesium chloride (MgCl₂) under acidic conditions. The TEOS/MgCl₂ molar ratio was varied from 1:0 to 0:1. The xerogels were characterized by a set of complementary techniques, namely, Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), nitrogen adsorption, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDX). Magnesium contents of silica-magnesia xerogels were between 1.3 and 16.0 wt%. Increasing TEOS/MgCl₂ molar ratio affords higher homogeneity and crystallinity. The presence of low Mg content (<5%) increases specific surface area compared to bare silica. A cubic grain morphology was observed for xerogels with higher Mg content.     

Preparation of “Green” Composites by the Sol-Gel Process: In Situ Silica Filled Natural Rubber

“Green” composites with different amounts of in situ silica nano-particles were prepared by a sol-gel reaction of tetraethoxysilane (TEOS) in natural rubber (NR). The control of swelling degree of TEOS in NR and concentration of n-butylamine in water was useful to change the amount of generated in situ silica in the uncured NR matrix. In situ silica up to 42 parts per hundred rubber by weight (phr) was successfully filled in the NR matrix. The particle size of in situ silica became larger with the increase of silica content from ca. 10 nm to ca. 40 nm for 10 phr--40 phr loadings in the NR matrix, respectively. Even when the amount of in situ silica content was high, the dispersion of in situ silica particles was more homogeneous than that of commercial silica (VN-3). The reinforcement effect of the in situ silica for NR vulcanizates increased with increasing the in situ silica content.     

Spherical hybrid silica particles modified by methacrylate groups

Organic–inorganic hybrid materials have been used as fillers to reinforce dental resin composites, which require strengthening to improve their performance in large stress-bearing applications such as crowns and multiple-unit restorations. Homogeneous organic–inorganic hybrid materials with high performance were prepared by mixing 3-methacryloxypropyltrimethoxysilane (MPTS) and tetraethylorthosilicate (TEOS) synthesized by the sol–gel route. The matrix was prepared by hydrolyzing and condensing the TEOS and MPTS, using basic catalysis and excess water. The resulting xerogel was treated at 50, 100, 150, and 200 °C for 4 h, and the structure was analyzed by thermogravimetry (TG/DTA), photoluminescence (PL), nuclear magnetic resonance (NMR ²⁹Si and ¹³C), transmission electron microscopy (TEM), infrared spectroscopy (IR), and Raman spectroscopy. The PL spectra displayed the Eu³⁺ lines characteristic of ⁵D₀ → ⁷F_{J (J = 0, 1, 2, 3, 4)} ions, and the blue emission was ascribed to the silica matrix. TG, MNR and infrared spectroscopy analyses indicated the hybrid silica was stable, with the organic part present up to 150 °C. Increasing the temperature of the heat treatment was found to increase the degree of hydrolysis. The size and morphology of the silica particles were identified by TEM.     

Influence of calcination temperature on structural and magnetic properties of nanocomposites formed by Co-ferrite dispersed in sol-gel silica matrix using tetrakis(2-hydroxyethyl) orthosilicate as precursor

Effects of calcination temperatures varying from 400 to 1000°C on structural and magnetic properties of nanocomposites formed by Co-ferrite dispersed in the sol-gel silica matrix using tetrakis(2-hydroxyethyl) orthosilicate (THEOS) as water-soluble silica precursor have been investigated. Studies carried out using XRD, FT-IR, TEM, STA (TG-DTG-DTA) and VSM techniques. Results indicated that magnetic properties of samples such as superparamagnetism and ferromagnetism showed great dependence on the variation of the crystallinity and particle size caused by the calcination temperature. The crystallization, saturation magnetization M_s and remenant magnetization M_r increased as the calcination temperature increased. But the variation of coercivity H_c was not in accordance with that of M_s and M_r, indicating that H_c is not determined only by the crystallinity and size of CoFe₂O₄ nanoparticles. TEM images showed spherical nanoparticles dispersed in the silica network with sizes of 10-30 nm. Results showed that the well-established silica network provided nucleation locations for CoFe₂O₄ nanoparticles to confinement the coarsening and aggregation of nanoparticles. THEOS as silica matrix network provides an ideal nucleation environment to disperse CoFe₂O₄ nanoparticles and thus to confine them to aggregate and coarsen. By using THEOS as water-soluble silica precursor over the currently used TEOS and TMOS, the organic solvents are not needed owing to the complete solubility of THEOS in water. Synthesized nanocomposites with adjustable particle sizes and controllable magnetic properties make the applicability of Co-ferrite even more versatile.     

Structure development during sol-gel process in organic-silica networks

Two types of the organic-silica hybrid networks were prepared and their formation and structure were studied in dependence on reaction conditions. The silica phase was formed by the sol-gel process from tetraethoxysilane (TEOS) or alkoxysilane endcapped prepolymers. The organic phase was composed of linear poly(oxypropylene) chain or the epoxide network arising by curing the diglycidyl ether of Bisphenol A (DGEBA) with poly(oxypropylene)diamine. Fast development of the structure during polymerization was followed by the in-situ small-angle X-ray scattering measurement. One- and two-stage polymerization procedures result in formation of heterogeneous but optically transparent nanocomposites with different structures.     

Structural Study of Silica Xerogel Composites Containing Pd Aggregates

Composites containing Pd aggregates dispersed in amorphous silica are of interest from both a fundamental and applied point of view because of their attractive catalytic properties. The silica powders added with palladium, prepared by the sol-gel method, were studied using X-ray diffraction, and IR- and UV-Vis-spectrophotometry. Silica xerogel samples were prepared using a ethanol/H₂O/TEOS molar ratio of 4:11.6:1 and loaded with sodium tetrachloropalladate. The silica xerogel microstructure of the powders was studied as a function of annealing temperature. Attention was paid to the evolution of the glass matrix as well as the palladium aggregates in the SiO₂ matrix. We found in our samples partial crystallization of the glass matrix in form of quartz and cristobalite phases with palladium oxide and metallic palladium phase at 1000^∘C. The Rietveld refinement method was used in order to determine the percentage of the phase contents.     

The Application of a Sol-Gel Technique to Preparation of a Heavy Metal Biosorbent from Yeast Cells

In this work we compared biosorbents obtained by encapsulation of polysaccharides, isolated from waste brewing biomass, in sol-gel derived silicates and an organic polymer. Biosorbents were prepared by mixing cross-linking-agents—organic or siliceous—with dried cells envelopes. Siliceous prepolymers were synthezised via transesterification and hydrolysis from tetraethoxysilane (TEOS) and methanol. Sorption of Cd2+, Cu2+ and Ag+ by biosorbent granules (0.25–0.6 mm) was examined in batch and in a packed column. The biosorbent prepared by interesterification of TEOS showed a 2–3 times higher intensity of sorption than the biosorbent cross-linked with epichlorohydrin (the most effective cross-linking organic agent) while the sorption capacity of both biosorbents was equal. The specific surface area of the silica matrix was 597 m2/g but only traces of metals were sequestered from solution with a concentration of Cd2+ of 50 mg/l. The biosorbent with a silica matrix is a heterogeneous material containing microporous matrix inclusions of thin cell walls. Its high sorption intensity and good mechanical strength will be useful in continuous metal uptake of low concentrations of metals.