Electroactive shape memory effect of radiation cross-linked SBS/LLDPE composites filled with carbon black

The poly(styrene-b-butadiene-b-styrene) (SBS) triblock copolymer and linear low-density polyethylene (LLDPE) were blended and irradiated by γ rays to prepare shape memory polymer (SMP). Different weight fractions of conductive carbon black (CB) were filled into SMP to form a novel electroactive shape memory CB/SBS/LLDPE composite. The CB reinforced radiation cross-linked SBS/LLDPE blends for the improvement of the mechanical weakness and conductivity of SBS/LLDPE bulk and for wide practical engineering uses. The electroactive shape memory CB/SBS/LLDPE composites were investigated by electrical properties, mechanical, dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and electroactive shape memory effects. It is found that the tensile strength, storage modulus, and resistance against mechanical and thermal mechanical cycle loading in the developed composites increased due to the role of reinforcement of CB. The melting temperatures and volume resistance of the composites decreased with the increment of CB for excellent electrical conductivity of CB. The electroactive shape memory effects of developed CB/SBS/LLDPE composites were affected by CB weight fractions and applied voltage, while good shape recovery could be obtained in the shape recovery test. When the CB fraction is more than 5 wt%, full recovery can be observed after tens of seconds and shape recovery speed increased with CB fractions and voltage increasing. However, the shape recovery rate decreases slightly with increment of cycle times.     

Physical Microfabrication of Shape‐Memory Polymer Systems via Bicomponent Fiber Spinning

As emerging technologies continue to require diverse materials capable of exhibiting tunable stimuli‐responsiveness, shape‐memory materials are of considerable significance because they can change size and/or shape in controllable fashion upon environmental stimulation. Of particular interest, shape‐memory polymers (SMPs) have secured a central role in the ongoing development of relatively lightweight and remotely deployable devices that can be further designed with specific surface properties. In the case of thermally‐activated SMPs, two functional chemical species must be present to provide (i) an elastic network capable of restoring the SMP to a previous strain state and (ii) switching elements that either lock‐in or release a temporary strain at a well‐defined thermal transition. While these species are chemically combined into a single macromolecule in most commercially available SMPs, this work establishes that, even though they are physically separated across one or more polymer/polymer interfaces, their shape‐memory properties are retained in melt‐spun bicomponent fibers. In the present study, we investigate the effects of fiber composition and cross‐sectional geometry on both conventional and cold‐draw shape memory, and report surprisingly high levels of strain fixity and recovery that generally improve upon strain cycling.

     

Structure–property relationships of fatty acid swollen,crosslinked natural rubber shape memory polymers

This article investigates shape memory polymers (SMPs) fabricated by swelling sulfur crosslinked natural rubber with four different molten fatty acids: lauric, myristic, palmitic, and stearic acid. As inexpensive additives, they allow commodity natural rubber to be directly converted to SMPs. The shape memory properties are investigated as a function of wt% fatty acid, the choice of fatty acid, and the applied load during shape memory programming. It is found that increasing the wt% acid improves the shape fixity up to ca. 97% at ≥50 wt% fatty acid, at which point the recovery starts to decline with increasing wt% acid due to network failure during shape programming. The shape fixity is found to depend on the yield stress and modulus of the fatty acid network, which both increase with increasing wt% acid. The choice of fatty acid also varies the trigger temperature for shape memory, which scales with the melting point of the fatty acid. Serendipitously, it is found that alignment of the fatty acid crystals during programming produces stiffer networks whose modulus increase with applied load, which counterbalances the higher elastic energy stored in the rubber network to produce lower sensitivity of the shape fixity to the applied load. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 673–687     

Redox‐ and Glucose‐Induced Shape‐Memory Polymers

A novel redox‐induced shape‐memory polymer (SMP) is prepared by crosslinking β‐cyclodextrin modified chitosan (β‐CD‐CS) and ferrocene modified branched ethylene imine polymer (Fc‐PEI). The resulting β‐CD‐CS/Fc‐PEI contains two crosslinks: reversible redox‐sensitive β‐CD‐Fc inclusion complexes serving as reversible phases, and covalent crosslinks serving as fixing phases. It is shown that this material can be processed into temporary shapes as needed in the reduced state and recovers its initial shape after oxidation. The recovery ratio and the fixity ratio are both above 70%. Furthermore, after entrapping glucose oxidase (GOD) in the system, the material shows a shape memory effect in response to glucose. The recovery ratio and the fixity ratio are also above 70%.

     

Shape memory and mechanical properties of cross-linked polyethylene/clay nanocomposites

Shape memory polymer (SMP) such as cross-linked low-density polyethylene (XLDPE), can return from its temporary shape to the original (permanent) shape upon heating. SMP in comparison with shape memory alloy (SMA) and shape memory ceramic (SMC) has lower stiffness, so generates lower recovery force when it is being used as an actuator. Also, when SMP is reinforced with traditional micro-fillers, it often loses its shape memory effect due to the high weight fraction of filler (20-30%). To overcome these disadvantages, nanoclays can be used. The smart resultant nanocomposite, even in small clay loading level (0-10 wt.%), shows higher modulus, strength, and the other physical properties such as higher recovery force, required to act as an actuator.In this work, the effect of modified montmorillonite on mechanical and shape memory properties as well as the force generation of a shape memory cross-linked low density polyethylene were investigated.The results show that the modulus of elasticity, the recovery temperature, the recovery force and force recovery rate increase with increasing organoclay in nanocomposites, but final recovery strain decreases slightly.     

Thermoreversibly Crosslinked Poly(ε‐caprolactone) as Recyclable Shape‐Memory Polymer Network

A new concept to build shape memory polymers (SMP) combining outstanding fixity and recovery ratios (both above 99% after only one training cycle) typical of chemically crosslinked SMPs with reprocessability restricted to physically crosslinked SMPs is demonstrated by covalently bonding, through thermoreversible Diels–Alder (DA) adducts, star‐shaped poly(ε‐caprolactones) (PCL) end‐functionalized by furan and maleimide moieties. A PCL network is easily prepared by melt‐blending complementary end‐functional star polymers in retro DA regime, then by curing at lower temperature to favour the DA cycloaddition. Such covalent network can be reprocessed when heated again at the retro DA temperature. The resulting SMP shows still excellent shape memory properties attesting for its good recyclability.

     

Evaluating shape memory behavior of polymer under deep-drawing conditions

Thermoplastic polyurethanes (TPU) are a popular family of shape memory polymers (SMP) due to their excellent abrasion & weather resistant, and mechanical strength. However, conventional processing operations or their combination with other polymers by adhesion or blending can affect their unique shape memory behavior. Currently, there are no effective methods to study and quantify the shape memory behavior of SMP based polymer laminates as they would respond to deep drawing operations. In this paper, a new method was introduced to effectively quantify the recovery behavior of TPU based polymer laminates undergoing simultaneous stretching and bending operations at different processing temperatures. The results presented show the value of developing a shape recovery characterization method that resembles the stresses of thermoforming to properly assess formability of shape memory polymers used in laminate constructions.     

苯乙烯基形状记忆聚合物热力学行为的有限元分析

对苯乙烯基形状记忆聚合物进行了拉伸实验研究,测定了该材料在25℃、30℃、40℃和50℃时的弹性模量和屈服极限.根据实验结果,建立了苯乙烯基形状记忆聚合物的材料参数方程,描述了苯乙烯基形状记忆聚合物在玻璃体转化过程中,材料参数和温度的关系.在假设形状记忆聚合物为各向同性材料的基础上,将Tobushi等建立的热力学本构方程从一维扩展到三维.基于有限元分析软件ABAQUS的二次开发功能,针对上述本构方程和材料参数方程,编写了可供ABAQUS调用的UMAT函数,并对苯乙烯基形状记忆聚合物实现形状记忆效应的高温变形、应力冻结和形状恢复等热力学过程,进行了有限元数值模拟分析.     

Shape-memory behavior of bisphenol A-type cyanate ester/carboxyl-terminated liquid nitrile rubber coreacted system

Bisphenol A-type cyanate ester (BACE) was modified by carboxyl terminated liquid nitrile rubber (CTBN) exhibiting shape memory properties. Shape memory BACE/CTBN copolymer was a new kind of smart materials, which has huge development potential and promising future. A series of shape memory BACE/CTBN copolymers were prepared by varying mass ratio of BACE and CTBN. The mechanical performance, thermal properties, and shape memory effect of the BACE/CTBN copolymers were systematically investigated. It was found that the BACE/CTBN copolymers have excellent shape-memory behavior, and the glass transition temperature (T _g ) of the copolymers can be adjusted with the content of CTBN. The shape recovery speed increases with the increment of the content of CTBN and the shape fixed ratio and shape recovery ratio are almost 100 %.     

Swelling behavior and mechanical properties of endlinked poly (dimethylsiloxane) networks and randomly crosslinked polyisoprene networks

Measurements of the equilibrium degree of swelling and of the equilibrium modulus were performed on poly(dimethylsiloxane) networks (PDMS) and on polyisoprene vulcanizates. The results support the concept that topological interactions between network chains, e.g. entanglements or the like, have a large influence on the rubber elastic behavior, at least within a certain range of network densities.PDMS networks having network chains of different lengths and varying functionlities of the crosslinks were prepared in bulk by endlinking fractionated ,-divinyl PDMS via multifunctional hydrogen-siloxanes (f=3 to 22). Natural rubber (NR) and synthetic liquid polyisoprene (IR) were cured in bulk with various amounts of dicumyl peroxide to give randomly crosslinked samples.The experimentally determined moduli and degrees of swelling were compared with theoretical predictions based on the phantom network theory and affine network theory, taking into account only chemical crosslinks. The observed discrepancies can be traced back to a contribution of topological interactions (trapped entanglements) to the total effective network density. The modulus and swelling data are consistent, thus ruling out non-equilibrium effects.     

Recent Insights Into the Biomedical Applications of Shape‐memory Polymers

Shape‐memory polymers (SMP) are versatile stimuli‐responsive materials that can switch, upon stimulation, from a temporary to a permanent shape. This advanced functionality makes SMP suitable and promising materials for diverse technological applications, including the fabrication of smart biomedical devices. In this paper, advances in the design of SMP are discussed, with emphasis on materials investigated for medical applications. Future directions necessary to bring SMP closer to their clinical application are also highlighted.

     

Two-way shape memory behavior of styrene-based bilayer shape memory polymer plate

In this work, a bilayer shape memory polymer (SMP) composite plate with two-way shape memory behavior is simulated, in which two types of styrene-based SMPs with well-separated glass transition temperatures are assembled in parallel. The finite element (FE) software ABAQUS is selected to exhibit the two-way shape memory effect during the shape recovery step and the Generalized Maxwell Model with the WLF equation is applied to characterize the temperature-dependent properties of the SMP bilayer plates. The effect factors of axial predeformation, thermal expansion coefficient and plate thickness are all considered for the two-way shape memory behavior of the styrene-based bilayer SMP plate. After that, a smart gripper composed of four SMP composite plates is proposed to realize grabbing and releasing functions for one-step and staged heating recovery. The FE results provide some necessary theoretical guidelines for future soft smart structural designs and optimization.     

Room temperature deformable shape memory composite with fine‐tuned crystallization induced via nanoclay particles

It is known that particular types of semi‐crystalline/elastomer polymer blends exhibit shape memory effects (SME) due to the dispersion of two immiscible phases. In this study, the crystal structure of polylactic acid (PLA)/ thermoplastic polyurethane (TPU) based shape memory polymer (SMP) is altered by incorporating small amounts of montmorillonite (MMT) nanoclay. The results indicate the incorporation of MMT can improve the compatibility of the two different polymers. Moreover, the presence of MMT affects the total crystallinity of the SMP and improves mechanical properties. Lastly, uniaxial stretching deformation can be applied to the SMP at room temperature conditions while maintaining its shape memory properties. With 1 wt % MMT particles, the recovery ratio (Rr) was nearly 95%, which indicated a strong recovery effect. The shape‐fixing ratio (Rf) remained above 95% for all composites due to plastic deformation applied at room temperature. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1197–1206     

Thermal-mechanical behavior of styrene-based shape memory polymer tubes

Styrene-based shape memory polymer (SMP) tubes were fabricated and their basic mechanical properties in different deformation states were investigated. The tensile, compression, bending and twisting shape memory properties of the tubes were analyzed and discussed, and the results indicated that SMP tubes exhibit good shape fixity ratio and shape recovery ratio. In addition, the shape recovery behavior was investigated at different heating rates. These experimental results will provide guidance for future applications of SMP tube structures.     

Reversible TAD Chemistry as a Convenient Tool for the Design of (Re)processable PCL‐Based Shape‐Memory Materials

A chemically cross‐linked but remarkably (re)processable shape‐memory polymer (SMP) is designed by cross‐linking poly(ε‐caprolactone) (PCL) stars via the efficient triazolinedione click chemistry, based on the very fast and reversible Alder–ene reaction of 1,2,4‐triazoline‐3,5‐dione (TAD) with indole compounds. Typically, a six‐arm star‐shaped PCL functionalized by indole moieties at the chain ends is melt‐blended with a bisfunctional TAD, directly resulting in a cross‐linked PCL‐based SMP without the need of post‐curing treatment. As demonstrated by the stress relaxation measurement, the labile character of the TAD–indole adducts under stress allows for the solid‐state plasticity reprocessing of the permanent shape at will by compression molding of the raw cross‐linked material, while keeping excellent shape‐memory properties.

     

Epoxy shape memory polymer (SMP): Material preparation,uniaxial tensile tests and dynamic mechanical analysis

The utilization of epoxy shape memory polymers (SMPs) as engineering materials for deployable structures has attracted considerable attention due to their excellent thermo-mechanical endurance and satisfactory processability. Knowledge of static and dynamic mechanical properties is essential for analyzing structural behavior and recovery, especially for new epoxy SMPs. In this paper, a new epoxy SMP was prepared with epoxy and aromatic amine curing agent. Uniaxial tensile tests and digital image correlation were used to obtain static mechanical properties. Dynamic mechanical analysis was carried out to evaluate glass transition temperatures that corresponded to the heat in the recovery process.It was found that elastic modulus, Poisson’s ratio and shear modulus are 1413 MPa, 0.35 and 591 MPa, respectively. The beginning of glass transition temperature of 37.4 °C could be effectively achieved by electrical heaters, validating the shape memory properties of epoxy SMPs. In general, this study could provide useful observations and basic mechanical properties of epoxy SMPs.     

形状记忆高分子材料

作为一种新型的功能材料,形状记忆高分子不仅具有形变量大、赋形容易、形状恢复温度便于调整、加工方便的优点,而且种类丰富、质轻价廉.按形状记忆的方式,它可分为热致感应型、光致感应型和化学物质感应型等,能满足不同的应用需求.     

Omnidirectional Shape Memory Effect via Lyophilization of PEG Hydrogels

Device applications of shape memory polymers demand diverse shape changing geometries, which are currently limited to non‐omnidirectional movement. This restriction originates from traditional thermomechanical programming methods such as uniaxial, biaxial stretching, bending, or compression. A solvent‐modulated programming method is reported to achieve an omnidirectional shape memory behavior. The method utilizes freeze drying of hydrogels of polyethylene glycol networks with a melting transition temperature around 50 °C in their dry state. Such a process creates temporarily fixed macroporosity, which collapses upon heating, leading to significant omnidirectional shrinkage. These shrunken materials can swell in water to form hydrogels again and the omnidirectional programming and recovery can be repeated. The fixity ratio (R _f) and recovery ratio (R _r) can be maintained at 90% and 98% respectively upon shape memory multicycling. The maximum linear recoverable strain, as limited by the maximum swelling, is ≈90%. Amongst various application potentials, one can envision the fabrication of multiphase composites by taking advantages of the omnidirectional shrinkage from a porous polymer to a denser structure.

     

Stability and deterioration of a shape memory polymer fabric composite under thermomechanical stress

Fibres and fabrics are often used to reinforce shape memory polymers (SMPs) to improve their mechanical strength and properties, and such composites have been widely used in engineering. However incorporation of fibres and fabrics in SMPs is often accompanied with the deterioration of thermomechanical properties and shape memory effect. The thermomechanical properties and deterioration mechanisms of a shape memory polymer composite (SMPC) under repeated mechanical stress were investigated. Up to 100% extension, the SMPCs showed good shape memory effect with excellent shape recovery ratio, recovery stress and mechanical properties; while beyond that the recovery ratio and recovery stress of the composites deteriorated rapidly due to the significant delamination and debonding of fibres and fabrics from the SMP resin and accumulation of broken fibres.     

Shape recovery studies for coupled deformations in an epoxy based amorphous shape memory polymers

In this work, the effect of sequence of shape setting on the shape recovery response for an epoxy based amorphous SMP was studied. The shape setting for coupled axial-twist deformations was done at two different temperatures within the glass transition band. A simple set-up with cameras was used to study the shape recovery behavior under free recovery experiments. Results show that the recovery behavior is independent of sequence of shape setting process but a shift in the shape recovery curve is noticed. The shape memory cycle for coupled deformations was also simulated in ABAQUS-VUMAT using the model proposed earlier by the authors based on multiple natural configurations. The simulated results show the capability of the model to analyze the memory effects of an amorphous polymer subjected to coupled deformations.