强氧化条件下非晶态Ni—Zr合金的表面结构及组成表征

用ＸＰＳ，ＵＰＳ，ＩＳＳ，ＳＥＭ方法分别对Ｎｉ２４Ｚｒ７６和Ｎｉ３６Ｚｒ６４两种组份的非晶态合在氧气压强为５×１０＾４Ｐａ温度为２５０℃～３００℃，的强氧化条件下，氧化前后表面的形貌及化学组成分析，结果表明，表面优化氧化Ｚｒ，并形成ＺｒＯ２物种，在非晶态Ｎｉ２４Ｚｒ７６合金中没有发现Ｎｉ的氧化，而Ｎｉ３６Ｚｒ６４组份的合金中Ｎｉ被氧化生成了ＮｉＯｘ（１〈ｘ〈１．５），氧化后表面富Ｚｒ将氧化后的Ｎｉ     

非晶Ni_(88)P_(12)合金薄膜的表面形貌特征与晶化行为的研究

采用化学镀的方法在３６３Ｋ和ｐ型Ｓｉ（１００）衬底上制得非晶Ｎｉ８８Ｐ１２合金薄膜．利用Ｘ射线衍射、Ｘ射线光电子能谱、扫描隧道显微镜和原子力显微镜对非晶合金薄膜及其经处理后形成的氧化态、还原态和晶态的结构、组分和表面的形貌特征作了研究，并对它的晶化行为作了初步探讨．结果表明，非晶合金薄膜是由纳米级微粒聚集成微米级颗粒组成；在低于晶化温度条件下经氧化和还原处理后的薄膜表面晶化；在晶化过程中，合金薄膜的非晶纳米微粒转变为微晶后长大成晶粒，其表面结构光滑平坦，几何边界清晰     

高密度脉冲电流对非晶Fe-Ni-Si-B合金结构弛豫与晶化的促进效应

对非晶Ｆｅ_７３Ｎｉ_５Ｓｉ_８Ｂ_１４合金分别进行了高密度脉冲电流及真空退火处理．用穆斯堡尔谱学与透射电子显微镜技术研究了处理后非晶的微观结构与晶化行为．实验结果表明，与退火处理相比，高密度脉冲电流产生的“电子风”促进了非晶合金的结构弛豫与晶化．随电流密度显著增加，这一促进效应进一步增强     

化学沉积非晶态合金的热学分析

用ＤＴＡ法分析表明沉积法获得的非晶态Ｎｉ－Ｐ合金各特征温度的晶化激活能明显低于激冷法获得的非晶合金。在同一升温速率下，脉冲化学沉积层的初始晶化激活能和晶化起始温度Ｔｏｎ都高于化学沉积层，说明脉冲化学沉积层的热稳定性优于化学沉积层。     

稀土镍磷非晶合金的PAS和DSC研究

文中报导了在Ｎｉ－Ｐ非晶合金中掺入稀土元素钇（Ｙ）的诱导共沉积方法；并通过正电子湮没寿命谱和示差扫描量热计研究了Ｎｉ－Ｐ－Ｙ非晶合金的缺陷态及热稳定性；还从不同角度讨论了稀土元素对该合金热稳定性的贡献。     

铁基纳米晶合金的热膨胀研究

研究了铁基纳米晶合金Ｆｅ_１３．５Ｃｕ_１Ｎｂ_３Ｓｉ_１３．５Ｂ_９和Ｆｅ_９１Ｚｒ_７Ｂ_２的热膨胀特性，并与相应成分的非晶合金做了比较。结果表明，在居里温度以下，纳米晶合金的热膨胀系数比非晶合金大得多，而在居里温度以上，两者几乎相等。认为上述的热膨胀的差别可能与铁基非晶态合金中存在的因瓦效应有关。 关键词：     

锗酸盐晶体压致非晶化的研究

高压拉曼散射研究表明．ＣｕＧｅＯ３，Ｌｉ２ＧｅＯ３和Ｌｉ６Ｇｅ２Ｏ７三种晶体分别在７，１２和１１ＧＰａ压力下转变为非晶。在高于起始转变压力以上一定范围压致非晶是可逆的，ＣｕＧｅＯ３，Ｌｉ２ＧｅＯ３和Ｌｉ６Ｇｅ２Ｏ７压致非晶的不可逆转变压力分别为１４．１，２０和２０ＧＰａ。压致非晶ＣｕＧｅＯ３的重新晶化温度在６００℃附近。锗酸及系列晶体的压致非晶化与它们的成份和结构有关，随着在这一系列晶体中Ｌｉ２Ｏ含量的增加，压致非晶化的压力趋于减小。     

负载金属对SO^2—4／ZrO2催化剂超强酸性和反应性能的影响

本文研究了气氛和负载金属对ＳＯ＾２－４／ＺｒＯ２超强酸催化剂正戊烷异构化反应性能的影响。ＳＯ＾２－４／ＺｒＯ２催化剂在Ｎ２中初活性较高，但稳定性很差，在Ｈ２中活性很低。负载Ｐｒ可显著地改善催化剂的活性，选择性和稳定性，负载Ｎｉ则使催化剂活性反而降低。催化剂的红外光谱试验结果表明，Ｈ２可使结合在ＺｒＯ２上的ＳＯ＾２－４，部分还原，减少超强酸位，Ｐｒ对ＳＯ＾２－４的还原有阻抑作用，使催化剂表面保留较多     

硼酸锂系列晶体的高压拉曼散射研究

本文进行了硼酸锂系列晶体的高压拉曼散射及其压致相变的研究。对于三硼酸锂（ＬｉＢ３Ｏ５），我们发现在５．０ＧＰａ有一可逆的晶态到晶态的相变，在２７．０ＧＰａ有一不可逆的晶态到非晶态的相变。二硼酸锂（Ｌｉ２Ｂ４Ｏ７）不可逆压致非晶相变发生在３２．０ＧＰａ附近。对于一硼酸锂，我们研究了０—５５．８ＧＰａ范围内的高压拉曼光谱，只在２．０ＧＰａ发现了一个晶态到晶态的相变，但未发现不可逆压致非晶化现象。在硼酸锂系列晶体中，不可逆压致非晶化的压力随Ｌｉ２Ｏ的含量的增加而升高。硼酸锂晶体中Ｌｉ２Ｏ的含量越高，压致非晶化越不容易发生，这与熔体急冷法制备硼酸锂玻璃的规律是一致的。     

纳米（Li2AO4）1—x—（ZrO2）x固体电解质陶瓷

用溶液凝胶共混法制备了纳米级的Ｌｉ２ＳＯ４－ＺｒＯ２复合固体电解质陶瓷。在复合陶瓷中，Ｌｉ２ＳＯ４、ＺｒＯ２的晶粒平均尺寸分别为４５、２７ｎｍ。晶粒尺寸的纳米化在材料中引入了大量的界面结构和表面结构。研究了掺不同量的纳米ＺｒＯ２第二相对Ｌｉ２ＳＯ４相变温度、相变行为及体系电导的影响，在纳米ＺｒＯ２作用下，Ｌｉ２ＳＯ４的相变温度可以降低１４０℃。在适当配比时，在５４０℃其离子电导可达到０．２Ｓ／ｃｍ     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.