Preparation and characterization of novel macroporous cellulose beads regenerated from ionic liquid for fast chromatography

Macroporous cellulose beads (MCB) used as anion exchangers were successfully prepared from cellulose solution in ionic liquid by double emulsification followed by cross-linking and modification with diethylaminoethyl. The pore structure and properties of the MCB were investigated and the results were compared with homogeneous cellulose beads (HCB). The MCB in size of about 71 μm is characterized by two sets of pores, i.e., diffusion pores (10–20 nm) and macropores (800–2000 nm), determined by mercury porosimeter. In addition, the bed permeability and effective porosity for BSA of MCB-packed column are 58% and 25% higher than those of HCB-packed column, respectively. The adsorption properties of MCB were evaluated, and compared with HCB and commercial absorbent (Sepharose 6 Fast Flow, CSFF). It is found that the pore diffusivity of BSA in MCB is over 7.9 times higher than HCB, and 6.7 times higher than CSFF, respectively. While the equilibrium adsorption capacity (q_m) of BSA on MCB is obviously lower than that on HCB and CSFF, the dynamic binding capacity (DBC) on MCB at 10% breakthrough reaches 47.7 mg/mL, higher than HCB (40.3 mg/mL) and CSFF (46.2 mg/mL) at flow rate of 360 cm/h. In addition, the MCB-packed column showed better column efficiency over the HCB packed one. Therefore, we demonstrated that the MCB possessed more advantages than other ones, like HCB and CSFF, and was expected as an ideal material for fast chromatography.     

IgG adsorption on a new protein A adsorbent based on macroporous hydrophilic polymers. I. Adsorption equilibrium and kinetics

Experimental determination and modeling of IgG binding on a new protein A adsorbent based on a macroporous resin were performed. The new adsorbent consists of polymeric beads based on hydrophilic acrylamido and vinyl monomers with a pore structure optimized to allow favorable interactions of IgG with recombinant protein A coupled to the resin. The particles have average diameter of 57 μm and a narrow particle size distribution. The IgG adsorption equilibrium capacity is 46 mg/cm³ and the effective pore diffusivity determined from pulse response experiments for non-binding conditions is 8.0 × 10⁻⁸ cm²/s. The IgG adsorption kinetics can be described with the same effective diffusivity by taking into account a heterogeneous binding mechanism with fast binding sites, for which adsorption is completely diffusion controlled, and slow binding sites for which adsorption is controlled by the binding kinetics. As a result of this mechanism, the breakthrough curve exhibits a tailing behavior, which appears to be associated with the slow binding sites. A detailed rate model taking into account intraparticle diffusion and binding kinetics is developed and is found capable of predicting both batch adsorption and breakthrough behavior over an ample range of experimental conditions. The corresponding effective diffusivity is independent of protein concentration in solution over the range 0.2–2 mg/cm³ and of protein binding as a result of the large pore size of the support matrix. Overall, the small particle size and low diffusional hindrance allow capture of IgG with short residence times while attaining substantial dynamic binding capacities.     

Dextran-grafted cation exchanger based on superporous agarose gel: Adsorption isotherms,uptake kinetics and dynamic protein adsorption performance

A novel chromatographic medium for high-capacity protein adsorption was fabricated by grafting dextran (40 kDa) onto the pore surfaces of superporous agarose (SA) beads. The bead was denoted as D-SA. D-SA, SA and homogeneous agarose (HA) beads were modified with sulfopropyl (SP) group to prepare cation exchangers, and the adsorption and uptake of lysozyme on all three cation-exchange chromatographic beads (SP-HA, SP-SA and SP-D-SA) were investigated at salt concentrations of 6–50 mmol/L. Static adsorption experiments showed that the adsorption capacity of SP-D-SA (2.24 mmol/g) was 78% higher than that of SP-SA (1.26 mmol/g) and 54% higher than that of SP-HA (1.45 mmol/g) at a salt concentration of 6 mmol/L. Moreover, salt concentration had less influence on the adsorption capacity and dissociation constant of SP-D-SA than it did on SP-HA, suggesting that dextran-grafted superporous bead is a more potent architecture for chromatographic beads. In the dynamic uptake of lysozyme to the three cation-exchange beads, the D_e/D₀ (the ratio of effective pore diffusivity to free solution diffusivity) values of 1.6–2.0 were obtained in SA-D-SA, indicating that effective pore diffusivities of SP-D-SA were about two times higher than free solution diffusivity for lysozyme. At 6 mmol/L NaCl, the D_e value in SA-D-SA (22.0 × 10⁻¹¹ m²/s) was 14.4-fold greater than that in SP-HA. Due to the superior uptake kinetics in SA-D-SA, the highest dynamic binding capacity (DBC) and adsorption efficiency (the ratio of DBC to static adsorption capacity) was likewise found in SP-D-SA. It is thus confirmed that SP-D-SA has combined the advantages of superporous matrix structure and drafted ligand chemistry in mass transport and offers a new opportunity for the development of high-performance protein chromatography.     

Synthesis, characterization and DNA binding studies of penta- and hexa-coordinated diorganotin(IV) 4-(4-nitrophenyl)piperazine-1-carbodithioates

Two chlorodiorganotin(IV) complexes with general formula R₂SnClL (R = n-C₄H₉(1) and C₂H₅(2) and a diphenyltin(IV) derivative with general formula Ph₂SnL₂(3), where L = 4-(4-nitrophenyl)piperazine-1-carbodithioate ligand, were prepared and characterized by elemental analysis, Raman, FT-IR, multinuclear NMR (¹H, ¹³C and ¹¹⁹Sn) and mass spectrometry. On the basis of spectroscopic data the effective coordination number of Sn atom was found five (1 and 2) and six (3) both in solution and solid state. Electrochemical, kinetic and thermodynamic parameters of complexes 1-3, interacting with DNA were evaluated by cyclic voltammetry. The linearity of the plots between the peak current (I) and the square root of the scan rate (ν^1/2) indicated the electrochemical processes to be diffusion controlled. The diffusion coefficients of the free (D_f) and DNA bound forms (D_b), standard rate constants (ks) and charge transfer coefficients (α) were determined by the application of Randle-Sevcik, Nicholson and Kochi equations. The values of binding constant and binding site size were evaluated from voltammetric data. The results revealed the following increasing order of binding strength: 1 (5.4 × 10³) < 3 (8.4 × 10³) < 2 (1.24 × 10⁴) M⁻¹. The UV-Vis spectroscopic data also indicated the same order of binding strength. Furthermore, the binding mode was suggested on the base of shift in peak potential (CV) and absorption maxima (UV-Vis spectroscopy).     

Facilitated transport of Am(III) through a flat-sheet supported liquid membrane (FSSLM) containing tetra(2-ethyl hexyl) diglycolamide (TEHDGA) as carrier

Facilitated transport of Am(III) in nitric acid medium using tetra(2-ethyl hexyl) diglycolamide (TEHDGA) in n-dodecane as carrier was studied. It was aimed at finding out the physico-chemical model for the transport of Am(III) using TEHDGA/n-dodecane as carrier under various experimental parameters like feed acidity, carrier concentration, varying strippant, varying membrane pore size, etc. The feed acidity and carrier concentrations were varied from 1 M to 6 M HNO₃ and 0.1 M to 0.3 M TEHDGA/n-dodecane, respectively. The transport of Am(III) increased with increase in feed acidity and carrier concentration reaching maximum at 3 M HNO₃ and 0.2 M TEHDGA/n-dodecane, respectively. Several stripping agents were tested and 0.1 M HNO₃ was found to be the most suitable stripping agent for this system. Almost quantitative transport of Am(III) was observed at about 180 min with feed acidity of 3 M HNO₃, 0.1 M HNO₃ as strippant and 0.2 M TEHDGA/n-dodecane as carrier. The pore size of the membrane support was varied from 0.20 μm to 5 μm and the permeation coefficient increased with increase in pore size up to 0.45 μm (2.43 × 10⁻³ cm/s), and then decreased with further increase in pore size. The plot between permeation coefficient vs. (membrane thickness)⁻¹ was linear which showed that the Am(III) transport was membrane diffusion limited. The membrane diffusion coefficient calculated from the graph was found to be 1.27 × 10⁻⁶ cm²/s and its theoretical value was 1.22 × 10⁻⁶ cm²/s. The stability of the carrier against leaching out of the membrane support as well as the integrity of membrane support was studied over a period of 30 days and was found to be satisfactory within the studied time period.     

Tris(2,2'-bipyridyl)ruthenium(II) electrochemiluminescence sensor based on carbon nanotube/organically modified silicate films

In this paper, a novel electrochemiluminescence (ECL) sensor was constructed to determine herring sperm (HS) double-stranded (ds) DNA. Tetramethoxysilane and dimethyldimethoxysilane were selected as co-precursors to form an organically modified silicate (ORMOSIL) film for the immobilization of multiwall carbon nanotubes (MWNTs) wrapped by poly(p-styrenesulfonate) (PSS), and then Tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) was successfully immobilized on a glassy carbon electrode via ion-association. PSS was employed to increase the conductivity of the ORMOSIL film and disperse the cut MWNTs, which were cut and shortened in a mixture of concentrated sulfuric and nitric acids, in the film. It was found that MWNTs could adsorb Ru(bpy)₃²⁺ and acted as conducting pathways to connect Ru(bpy)₃²⁺ sites to the electrode. MWNTs also played a key role as materials for the mechanical and thermal properties. The ECL performance of this modified electrode was evaluated in a flow injection analysis (FIA) system, and the detection limit (S/N = 3) for HS ds-DNA was 2.0 × 10⁻⁷ g mL⁻¹ with a linear range from 1.34 × 10⁻⁶ to 6.67 × 10⁻⁴ g mL⁻¹ (R² = 0.9876). In addition, the ECL sensor presented excellent characteristics in terms of stability, reproducibility and application life.     

Defluoridation kinetics of 200 °C calcined bauxite, gypsum, and magnesite and breakthrough characteristics of their composite filter

Reaction kinetics and breakthrough characteristics in water defluoridation were studied through experiments with 200 °C-calcined bauxite, gypsum and magnesite and their composite filter. The aim was to determine defluoridation potential of a composite filter of the three locally sourced natural materials in contribution towards fluorosis mitigation. The materials were crushed and sieved to particle sizes of 1.2-1.4 mm diameter, and then heat-treated at 200 °C for 2 h. Their defluoridation capacities and reaction kinetics were determined in batch. A composite was then prepared in the ratio of the loading capacities. Breakthrough characteristics were experimented on in fixed bed through bed depth service time (BDST) design model, empty bed residence time (EBRT) optimisation model and the two parameter-logistics (2-PL) model. Mean loading capacities of 5.6, 3.4 and 1.7 mg F⁻/g were obtained for bauxite, gypsum and magnesite, respectively. Loading capacities decreased, while sorption percentages increased, with increase in dose level. Second order kinetics observed had rate constants 4.07 × 10⁻², 1.87 × 10⁻², 1.59 × 10⁻² g mg⁻¹ min⁻¹ for bauxite, gypsum and magnesite, respectively. Composites, bauxite and gypsum decreased, while magnesite increased water pH. Time at 50% breakthrough (τ) obtained experimentally compared well with τ obtained through the two-parameter logistics model indicating good fitness of data to the model. Greater doses obtained higher breakthrough times that were, 120, 210, 255 and 360 min for 45, 75, 120 and 150 g, respectively. Critical bed depth (Z_o), 7.71 cm and an operating line, ? = 4 × 10⁻⁴δ − 0.0757δ + 4.86 (? = adsorbent exhaustion rate, δ = EBRT) were obtained. The water quality was within recommended quality limits for pH, apparent colour, hardness, and residual concentrations of SO₄²⁻, Cl⁻, Fe²⁺, and Al³⁺ in fixed bed. The research showed that a composite filter of the three materials, prepared in the ratio of their loading capacities and calcined at 200 °C, is a potential defluoridating filter in fixed bed configuration.     

Comparison of pyrimethanil-imprinted beads and bulk polymer as stationary phase by non-linear chromatography

A pyrimethanil-imprinted polymer (P1) was prepared by iniferter-mediated photografting a mixture of methacrylic acid and ethylene dimethacrylate onto homemade near-monodispersed chloromethylated polydivinylbenzene beads. The chromatographic behaviour of a column packed with these imprinted beads was compared with another column packed with irregular particles obtained by grinding a bulk pyrimethanil-imprinted polymer (P2). The comparison was made using the kinetic model of non-linear chromatography, studying the elution of the template and of two related substances, cyprodinil and mepanipyrim. Extension of the region of linearity, capacity factors for the template and the related substances, column selectivity, binding site heterogeneity, apparent affinity constant (K) and lumped kinetic association (k_a) and dissociation rate constant (k_d) were studied during a large interval of solute concentration, ranging between 1 and 2000 μg/ml. From the experimental results obtained, in the linearity region of solute concentration column selectivity and binding site heterogeneity remained essentially the same for the two columns, while column capacity (at 20 μg/ml, P1 = 23.1, P2 = 11.5), K (at 20 μg/ml, P1 = 8.3 × 10⁶ M⁻¹, P2 = 2.5 × 10⁶ M⁻¹) and k_a (at 20 μg/ml, P1 = 3.5 μM⁻¹ s⁻¹, P2 = 0.47 μM⁻¹ s⁻¹) significantly increased and k_d (at 20 μg/ml, P1 = 0.42 s⁻¹, P2 = 0.67 s⁻¹) decreased for the column packed with the imprinted beads. These results are consistent with an influence of the polymerisation method on the morphology of the resulting polymer and not on the molecular recognition properties due to the molecular imprinting process.     

Synthesis and DNA cleavage properties of ternary Cu(II) complexes containing histamine and amino acids

The ternary complexes of [Cu^II(Hist)(Tyr)]⁺1 and [Cu^II(Hist)(Trp)]⁺2 have been synthesized, structurally characterized and their DNA binding and cleavage abilities probed. The intrinsic binding constants (K_b) for complexes/CT-DNA were also determined (K_b = 2.7 × 10² for complex 1 and K_b = 2.2 × 10² for complex 2). These complexes exhibit their nuclease activity on plasmid DNA, which seems to depend on the nature of the aromatic moiety. The DNA hydrolytic cleavage rate constants were also determined for complexes 1 and 2, which are 0.91 and 0.79 h⁻¹, respectively.     

Structural and conductivity studies of Y10−xLaxW2O21

The aim of this work was to determine structural parameters of the Y_10−xLa_xW₂O₂₁ (x=0-10) solid solution series and investigate their electric properties. Crystallographic data shows a gradual increase in symmetry with increasing La content, as the structure evolves from orthorhombic, Y₁₀W₂O₂₁, towards the pseudo-cubic structure of Y₅La₅W₂O₂₁. The solubility limit of La₂O₃ was found to be 50% (x=5). Above this level two phases were observed, La₆W₂O₁₅ and (La,Y)_10+xW_2−xO_21−δ. The conductivity of Y rich samples was very low, with σ of the order 2×10⁻⁵-5×10⁻⁵ S cm⁻¹ at 1000 °C, whilst ionic conductivity was observed for most La rich doped samples. The highest conductivity was observed for La₁₀W₂O₂₁ and its doped analogues, at 1×10⁻³-5×10⁻³ S cm⁻¹ at 1000 °C. Unit cell parameters were determined as a function of temperature from 0 to 1000°C, and thermal expansion of these materials was determined from temperature studies carried out at the Australian Synchrotron facility in Melbourne, Victoria, Australia.     

Durable diagnosis of seminal vesicle and sexual gland diseases using the nano optical sensor thin film Sm-doxycycline complex

A new method in which a nano optical sensor for diagnosis of different diseases of seminal vesicle and sexual gland was prepared. The working principle of the method depends on the determination of the fructose concentration in semen of different patients by using nano optical sensor thin film Sm-doxycycline doped in sol–gel matrix. The assay is based on the quenching of the characteristic emission bands of Sm³⁺ present in silica doped Sm-doxycycline nanooptode thin film by different fructose concentrations in acetonitrile at λ_ex = 400 nm. This method was optimized for parameters, such as, solvent effect, operational stability, shelf life and interference parameters. Good and reproducible linearity (1 × 10⁻⁹ – 5.0 × 10⁻⁵ mol L⁻¹) with a detection limit of 9.0 × 10⁻¹⁰ mol L⁻¹ and quantification limit of detection (LOQ) 2.7 × 10⁻⁹ mol L⁻¹ were obtained. Seminal fructose determination in different patient samples after appropriate dilutions confirmed the reliability of this technique. The method was successfully applied for routine fructose monitoring in human semen samples of different cases such as; obstructive and non-obstructive azoospermia, inflammation of male accessory glands, atrophy of seminal vesicle, congenital vas deferens and retrograde ejaculation.     

Photovoltammetric behavior and photoelectrochemical determination of p-phenylenediamine on CdS quantum dots and graphene hybrid film

A photoelectroactive film composed of CdS quantum dots and graphene sheets (GS) was coated on F-doped SnO₂ (FTO) conducting glass for studying the electrochemical response of p-phenylenediamine (PPD) under photoirradiation. The result indicated that the cyclic voltammogram of PPD on CdS–GS hybrid film became sigmoidal in shape after exposed under visible light, due to the photoelectrocatalytic reaction. Such a photovoltammetric response was used to rapidly optimize the photoelectrocatalytic activity of hybrid films composed of different ratios of CdS to GS toward PPD. The influences of scan rate and pH on the photovoltammetric behavior of PPD on CdS–GS film revealed that although the controlled step for electrochemical process was not changed under photoirradiation, more electrons than protons might participate the photoelectrocatalytic process. Furthermore, the photoelectroactive CdS–GS hybrid film was explored for PPD determination based on the photocurrent response of film toward PPD. Under optimal conditions, the photocurrent signal on CdS–GS film was linearly proportional to the concentration of PPD ranging from 1.0 × 10⁻⁷ to 3.0 × 10⁻⁶ mol L⁻¹, with a detection limit (3S/N) of 4.3 × 10⁻⁸ mol L⁻¹. Our work based on CdS–GS hybrid film not only demonstrated a new facile photovoltammetric way to study the photoinduced electron transfer process of PPD, but also developed a sensitive photoelectrochemical strategy for PPD determination.     

Direct electrochemistry and electrocatalysis of cytochrome c immobilized on gold nanoparticles-chitosan-carbon nanotubes-modified electrode

A robust and effective nanohybrid film based on gold nanoparticles (GNPs)/chitosan (Chit)/multi-walled carbon nanotubes (MWNTs) was prepared by a layer-by-layer self-assembly technique. Cytochrome c (Cyt c) was successfully immobilized on the nanohybrid film modified glassy carbon (GC) electrode by cyclic voltammetry. The direct electron transfer between Cyt c and the modified electrode was investigated in detail. Cyt c shows a couple of quasi-reversible and well-defined cyclic voltammetry peaks with a formal potential (E^0′) of −0.16 V (versus Ag/AgCl) in pH 7.0 phosphate buffer solution (PBS). The Cyt c/GNPs/Chit/MWNTs modified GC electrode gives an improved electrocatalytic activity towards the reduction of hydrogen peroxide (H₂O₂). The sensitivity is 92.21 μA mM⁻¹ cm⁻² and the calculated apparent Michaelis-Menten constant () is 0.791 mM, indicating a high-catalytic activity of Cyt c. The catalysis currents increase linearly to the H₂O₂ concentration in a wide range of 1.5 × 10⁻⁶ to 5.1 × 10⁻⁴ M with a correlation coefficient 0.999. The detection limit is 9.0 × 10⁻⁷ M (at the ratio of signal to noise, S/N = 3). Moreover, the modified electrode displays rapid response (5 s) to H₂O₂, and possesses good stability and reproducibility.     

Quantitative study of stereospecific binding of monoclonal antibody to anti-benzo(a)pyrene diol epoxide-N-dG adducts by capillary electrophoresis immunoassay

The stereospecific binding of monoclonal antibody (mAb) 8E11 to anti-benzo(a)pyrene diol epoxide (BPDE)-dG adducts in single nucleoside, long oligonucleotide, and genomic DNA were quantitatively evaluated using noncompetitive and competitive capillary electrophoresis (CE) immunoassays. Two single-stranded TMR-BPDE-90mers containing a single anti-BPDE-dG adduct with defined stereochemistry and a fluorescent label at 5′-end were used as fluorescent probes for competitive CE immunoassay. To quantitatively evaluate the binding affinity through competitive CE immunoassays, a series of equations were derived according to the binding stoichiometry. The binding of mAb 8E11 to trans-(+)-anti-BPDE-dG displays strongest affinity (K_b: 3.57 × 10⁸ M⁻¹) among all four investigated anti-BPDE-dG mononucleoside adducts, and the cis-(−)-anti-BPDE-dG displays lowest affinity (K_b: 1.14 ×10⁷ M⁻¹). The binding of monoclonal antibody (mAb) 8E11 to BPDE-dG adducts in long DNA (90mer) preferentially forms the complex with a stoichiometry of 1:1, and that mAb 8E11 displays a slightly higher affinity with trans-(+)-anti-BPDE-90mers (K_b: 6.36 ± 0.54 × 10⁸ M⁻¹) than trans-(−)-anti-BPDE-90mers (K_b: 4.52 ± 0.52 × 10⁸ M⁻¹). The mAb 8E11 also displays high affinity with BPDE-dG adducts in genomic DNA (K_b: 3.74 × 10⁸ M⁻¹), indicating its promising applications for sensitive immuno-detection of BPDE-DNA adducts in genomic DNA.     

Influence of hole mobility on the response characteristics of p-type nickel oxide thin film based glucose biosensor

RF sputtered p-type nickel oxide (NiO) thin film exhibiting tunable semiconductor character which in turns enhanced its functional properties. NiO thin film with high hole mobility is developed as a potential matrix for the realization of glucose biosensor. NiO thin film prepared under the optimized deposition conditions offer good electrical conductivity (1.5 × 10⁻³ Ω⁻¹-cm⁻¹) with high hole mobility (2.8 cm² V⁻¹ s⁻¹). The bioelectrode (GO_x/NiO/ITO/glass) exhibits a low value of Michaelis–Menten constant (K_m = 1.05 mM), indicating high affinity of the immobilized GO_x toward the analyte (glucose). Due to the high surface coverage (2.32 × 10⁻⁷ mol cm⁻²) of the immobilized enzyme on to the NiO matrix and its high electrocatalytic activity, the prepared biosensor exhibits a high sensitivity of 0.1 mA (mM⁻¹-cm⁻²) and a good linearity from 25 to 300 mg dL⁻¹ of glucose concentration with fast response time of 5 s. Various functional properties of the material (mobility, crystallinity and stress) are found to influence the charge communication feature of NiO thin film matrix to a great extent, resulting in enhanced sensing response characteristics.     

Electrochemical analysis of methylparathion pesticide by a gemini surfactant-intercalated clay-modified electrode

In this study, an hybrid material obtained by the intercalation of a gemini surfactant between the layers of smectite-type clay, was fully characterized by X-ray diffraction (XRD), infrared spectroscopy (FTIR) and N₂ adsorption-desorption experiments (BET method). To ascertain the intercalation process of the starting clay by the dimeric surfactant, the permselectivity and ion exchange properties of the organoclay were investigated by ion exchange voltammetry using [Fe(CN)₆]³⁻ and [Ru(NH₃)₆]³⁺ as redox probes, by the means of a clay film-modified electrode. Due to its organophilic character, the surfactant-intercalated complex was evaluated as electrode modifier for the accumulation of methylparathion (MP) pesticide. The electroanalytical procedure involves two steps: preconcentration under open-circuit followed by voltammetric detection by square wave voltammetry: the peak current obtained (after 5 min preconcentration in 4 × 10⁻⁵ mol L⁻¹ MP) on a glassy carbon electrode coated by a thin film of the modified clay was more than five times higher than that exhibited by the same substrate covered by a film of the pristine clay. This opens the way to the development of a sensitive method for the detection of the pesticide. Many parameters that can affect the stripping response (surfactant loading of the hybrid material, film composition, pH of the detection medium, preconcentration time, electrolysis potential and duration as well as some other instrumental parameters) were systematically investigated to optimize the sensitivity of the organoclay-modified electrode. After optimization, a linear calibration curve for MP was obtained in the concentration range from 4 × 10⁻⁷ to 8.5 × 10⁻⁶ mol L⁻¹ in acetate buffer (pH 5), with a detection limit of 7 × 10⁻⁸ mol L⁻¹ (signal-to-noise ratio equal to 3). The interference effect of various inorganic ions likely to influence the stripping determination of the pesticide was also examined, and the described method was applied to spring water analysis.     

Study on the binding behavior of bovine serum albumin with cephalosporin analogues by chemiluminescence method

The luminol-bovine serum albumin chemiluminescence system was proposed for the first time. It was found that the hydrophilic luminol bound to the hydrophilic domain at Trp¹³⁴ of BSA with accelerating the electrons transferring rate of excited 3-aminophthalate, which led to the enhancement CL intensity of luminol at 425 nm. The increment of chemiluminescence intensity was proportional to the concentrations of bovine serum albumin from 5.0 × 10⁻¹¹ to 1.0 × 10⁻⁸ mol L⁻¹ with the linear equation of ΔI = 7.47C_BSA + 4.89 (R² = 0.9950). Based on the remarkable quenching effect of cephalosporin on the luminol-bovine serum albumin chemiluminescence system, the interaction of bovine serum albumin-cephalosporin was studied by flow injection-chemiluminescence method. A valuable model for studying the interaction of bovine serum albumin-cephalosporin was constructed and the formula lg[(I₀ − I)/I] = lg K_D + n lg[D] was obtained. The binding parameters calculated by the model did agree very well with the results obtained by fluorescence quenching method. The major binding force of bovine serum albumin with cephalosporins was the hydrophobic effect. The binding ability of cephalosporin analogues to bovine serum albumin followed the pattern: cefoperazone, ceftriaxone and cefotaxime > cefuroxime and cefaclor > cefadroxil, cefradine and cefazolin, which was close to the order of their antibacterial ability. Using flow injection chemiluminescence method also obtained the stoichiometric ratio, the average of association constant K_P and dissociation degree α of luminol-bovine serum albumin were 1:1, 1.12 × 10⁷ L mol⁻¹ and 0.086, respectively.     

A novel solid-state electrochemiluminescence detector for capillary electrophoresis based on tris(2,2'-bipyridyl)ruthenium(II) immobilized in Nafion/PTC-NH2 composite film

A new electrochemiluminescence (ECL) detector for capillary electrophoresis (CE) based on tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) immobilized in Nafion/PTC-NH₂ (an ammonolysis product of 3,4,9,10-perylenetetracarboxylic dianhydride (PTCDA)) composite film was presented for the first time. The Nafion/PTC-NH₂ composite film could effectively immobilize tris(2,2′-bipyridyl)ruthenium(II) via ion-exchange and electrostatic interaction. Cyclic voltammetric and ECL behavior of Nafion/PTC-NH₂/Ru composite film was investigated compared to Nafion/Ru composite. The Nafion/PTC-NH₂/Ru composite film exhibited good ECL stability and simple operability. Then the CE with solid-state ECL detector system was successfully used to detect sophora - a quinolizidine type - alkaloids as sophoridine (SR) and matrine (MT). The CE-ECL parameters that affected separation and detection were optimized. Under the optimized conditions, the linear range was from 2.5 × 10⁻⁸ to 2 × 10⁻⁶ mol/L for SR, 1.0 × 10⁻⁸ to 1.0 × 10⁻⁶ mol/L for MT. The detection limit (S/N = 3) was estimated to be 5 × 10⁻⁹ and 10⁻⁹ mol/L for SR and MT, respectively. It was shown that the CE coupling with solid-state ECL detector system exhibited satisfying sensitivity of analysis.     

Poly(methylene blue) functionalized graphene modified carbon ionic liquid electrode for the electrochemical detection of dopamine

An ionic liquid 1-butylpyridinium hexafluorophosphate based carbon ionic liquid electrode (CILE) was used as the substrate electrode and a poly(methylene blue) (PMB) functionalized graphene (GR) composite film was co-electrodeposited on CILE surface by cyclic voltammetry. The PMB–GR/CILE exhibited better electrochemical performances with higher conductivity and lower electron transfer resistance. Electrochemical behavior of dopamine (DA) was further investigated by cyclic voltammetry and a pair of well-defined redox peaks appeared with the peak-to-peak separation (ΔE_p) as 0.058 V in 0.1 mol L⁻¹ pH 6.0 phosphate buffer solution, which proved a fast quasi-reversible electron transfer process on the modified electrode. Electrochemical parameters of DA on PMB–GR/CILE were calculated with the electron transfer number as 1.83, the charge transfer coefficients as 0.70, the apparent heterogeneous electron transfer rate constant as 1.72 s⁻¹ and the diffusional coefficient (D) as 3.45 × 10⁻⁴ cm² s⁻¹, respectively. Under the optimal conditions with differential pulse voltammetric measurement, the linear relationship between the oxidation peak current of DA and its concentration was obtained in the range from 0.02 to 800.0 μmol L⁻¹ with the detection limit as 5.6 nmol L⁻¹ (3σ). The coexisting substances exhibited no interference and PMB–GR/CILE was applied to the detection of DA injection samples and human urine samples with satisfactory results.     

Electrochemical behaviors of guanosine on carbon ionic liquid electrode and its determination

The electrochemical behaviors of guanosine on the ionic liquid of N-butylpyridinium hexafluorophosphate (BPPF₆) modified carbon paste electrode (CPE) was studied in this paper and further used for guanosine detection. Guanosine showed an adsorption irreversible oxidation process on the carbon ionic liquid electrode (CILE) with the oxidation peak potential located at 1.12 V (vs. SCE) in a pH 4.5 Britton-Robinson (B-R) buffer solution. Compared with that on the traditional carbon paste electrode, small shift of the oxidation peak potentials appeared but with a great increment of the oxidation peak current on the CILE, which was due to the presence of ionic liquid in the modified electrode adsorbed the guanosine on the surface and promoted the electrochemical response. The electrochemical parameters such as the electron transfer coefficient (α), the electron transfer number (n), and the electrode reaction standard rate constant (k_s) were calculated as 0.74, 1.9 and 1.26 × 10⁻⁴ s⁻¹, respectively. Under the optimal conditions the oxidation peak current showed a good linear relationship with the guanosine concentration in the range from 1.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol/L by cyclic voltammetry with the detection limit of 2.61 × 10⁻⁷ mol/L (3σ). The common coexisting substances showed no interferences to the guanosine oxidation. The CILE showed good ability to distinguish the electrochemical response of guanosine and guanine in the mixture solution. The urine samples were further detected by the proposed method with satisfactory results.