Determination of pharmaceuticals in river water by column switching of large sample volumes and liquid chromatography–diode array detection,assisted by chemometrics: An integrated approach to green analytical methodologies

An analytical method for the simultaneous determination of nine β-blockers (sotalol atenolol, nadolol, pindolol, metoprolol, timolol, bisoprolol, propanolol and betaxolol) and two analgesics (paracetamol and phenazone) in river water by liquid chromatography and diode array detection is reported. The method involves a modified precolumn switching methodology replacing the small precolumn with a short C18 liquid chromatography column (50 mm × 4.6 mm, 5 μm particle size), thus allowing the preconcentration of large water sample volumes whereas interferences eluting at the first of the chromatogram were discarded to waste. This approach allowed to preconcentrate 30 mL river water samples, modified with 0.4% MeOH, achieving univariate method detection and determination limits ranged between 0.03 and 0.16 μg L⁻¹ and between 0.2 and 0.5 μg L⁻¹, respectively, with precision values lower than 9.4% for spiking levels at the quantitation limits of each analyte and lower than 4.0%, except bisoprolol (8.3%), for higher spiking levels (1.0 μg L⁻¹ of all analytes). Matrix background was reduced in three way data by a baseline correction following the Eilers methodology, whereas multivariate curve resolution and alternating least squares in combination with the standard addition calibration method, applied to these data, coped with overlapping peak, systematic (additive) and proportional (matrix effect) errors. The method was successfully applied for the determination of the target pharmaceuticals in river water from three places in a river stream with acceptable recoveries and precision values, taking into account the complexity of the analytical problem. The joint statistical test for the slope and the intercept of the linear regression between the nominal concentration values versus those predicted, showed that the region computed contained the theoretically expected values (0) for the intercept and (1) for the slope (at a confidence level of 95%), which indicates the absence of both constant and proportional errors in the predicted concentrations.     

Chemometric assisted solid-phase microextraction for the determination of anti-inflammatory and antiepileptic drugs in river water by liquid chromatography-diode array detection

In the present work, an analytical method for the simultaneous determination of seven non steroidal anti-inflammatory drugs (naproxen, ketoprofen, diclofenac, piroxicam, indomethacin, sulindac and diflunisal) and the anticonvulsant carbamazepine is reported. The method involves preconcentration and clean-up by solid-phase microextraction using polydimethylsiloxane/divinylbenzene fibers, followed by liquid chromatography with diode array detection analysis. Parameters that affect the efficiency of the solid-phase microextraction step such as soaking solvent, soaking period, desorption period, stirring rate, extraction time, sample pH, ionic strength, organic solvent and temperature were investigated using a Plackett-Burman screening design. Then, the factors presenting significant positive effects on the analytical response (soaking period, stirring rate, stirring time) were considered in a further central composite design to optimize the operational conditions for the solid phase microextraction procedure. Additionally, multiple response simultaneous optimization by using the desirability function was used to find the optimum experimental conditions for the on-line solid-phase microextraction of analytes in river water samples coupled to liquid chromatography and diode array detection. The best results were obtained using a soaking period of 5 min, stirring rate of 1400 rpm and stirring time of 44 min. The use of solid-phase microextraction technique avoided matrix effect and allowed to quantify the analytes in river water samples by using Milli-Q based calibration graphs. Recoveries ranging from 71.6% to 122.8% for all pharmaceuticals proved the accuracy of the proposed method in river water samples. Method detection limits were in the range of 0.5-3.0 microgL(-1) and limits of quantitation (LOQs) were between 1.0 and 4.0 microgL(-1) for pharmaceutical compounds in river water samples. The expanded uncertainty associated to the measurement of the concentration ranged between 8.5% and 29.0% for 20 microgL(-1) of each analyte and between 9.0% and 29.5% for the average of different concentration levels. The main source of uncertainty was the calibration step in both cases.     

Fast liquid chromatography-diode array detection assisted by chemometrics for quantification of seven ultraviolet filters in effluent wastewater

A fast chromatographic method is presented for simultaneous quantification of seven organic ultraviolet (UV) filters (benzophenone-3,4-methylbenzilidene camphor, octocrylene, 1-(4-tert-butylphenyl)-3-(4-methyoxyphenyl)1,3-propanedione), ethylhexyl methoxy cinnamate, ethylhexyl salicylate and homosalate) in effluent wastewater samples. The UV filters were pre-concentrated by Bond Elut-ENV cartridges and separated on an ODS column (15 cm × 0.46 cm, 5 μm) in less than 2.5 min using a non-aqueous mobile phase of methanol-acetonitrile (50:50, v/v) with flow-rate of 1.5 mL min⁻¹. Appropriate baseline correction through asymmetric least squares was applied to reduce the matrix of background signals in three way data. Then, second-order calibration based on multivariate curve resolution-alternating least squares (MCR-ALS) was implemented on the unfolded three-way data obtained from liquid chromatography with diode array detection (LC-DAD) through standard addition calibration method for handling co-eluted peaks, systematic and proportional errors. Recoveries ranging from 76% to 130% and %RSD values less than 11.2 for all UV filter shows the accuracy and precision of the proposed method in wastewater samples. In addition, statistical t-test as well as computed elliptical joint confidence region (EJCR) confirms the accuracy of the proposed method and indicates the absence of both constant and proportional errors in the predicted concentrations. This study demonstrates that coupling of the fast HPLC-DAD method with powerful algorithm of MCR-ALS can be considered as an efficient method for quantification of UV filters in highly contaminated samples of wastewaters where both time and cost per each analysis can be reduced significantly.     

Comparative study of the determination of trimethylamine in water and air by combining liquid chromatography and solid-phase microextraction with on-fiber derivatization

This work describes a new approach for the determination of trimethylamine (TMA) in water and air by liquid chromatography (LC). The assay is based on the employment of a solid-phase microextraction (SPME) fiber for sampling and for derivatization of the analyte with the fluorogenic reagent 9-fluorenylmethyl chloroformate (FMOC). The fiber, with a Carbowax-templated resin −50 μm coating, was first immersed into a solution of the reagent. Once loaded with the reagent, the fiber was immersed into the water samples or exposed to the air samples in order to extract and to derivatize the analyte. Finally, the fiber was placed into a HPLC-SPME interface to desorb and transfer the TMA-FMOC derivative to the LC equipment. A comparative study of the analytical characteristics of the procedure in water and air samples was carried out. Under optimized conditions, the proposed approach permits the quantification of TMA in solution within the 1.0-10.0 μg/ml interval and in air within the 25-200 mg/m³ interval. The limits of detection were 0.25 μg/ml and 12 mg/m³ (25 °C, 1.013 × 10⁻⁵ Pa) in water and air, respectively. The utility of the proposed method for determining TMA in different kind of samples is discussed.     

On-line determination of organophosphorus pesticides in water by solid-phase microextraction and gas chromatography with thermionic-selective detection

This paper describes the extraction of 49 organophosphorus pesti-cides (OPPs) from water samples using solid-phase microextraction (SPME). Three fibers, including a 15-μm XAD-coated fiber, a 85-μm polyacrylate-coated fiber, and a 30-μm polydimethylsilox-ane-coated fiber (PDMS), were evaluated here. The effects of stirring and the addition of NaCl to the sample were examined for the polyacrylate-coated fiber. The precision of the technique was examined for all three fibers and the extraction kinetics were investigated using the XAD- and polyacrylate-coated fibers. With some exceptions, the XAD- and polyacrylate-coated fibers performed better than the PDMS-coated fiber. The superiority of the XAD-nd polyacrylate-coated fiber. The superiority of the XAD- and polyacrylate-coated fibers over the PDMS-coated fibers can be attribuibuted to the aromatic functionalities of the XAD and the polar functionalities in the polyacrylate. The relatively high percent RSDs indicate that the SPME technique needs to be further refined before it can be used for anything other than screening. A more effective form of agitation than mechanical stirring may be neccessary to reduce variability and achieve a faster equilibrium between the sample and the SPME fiber.     

Fast quantitative analysis of four tyrosine kinase inhibitors in different human plasma samples using three‐way calibration‐ assisted liquid chromatography with diode array detection

A simple method has been developed by combining high‐performance liquid chromatography with diode array detection with the alternating trilinear decomposition method for simultaneous determination of four tyrosine kinase inhibitors in different human plasma samples. Chromatographic separation of the analytes was performed on a reversed‐phase column with methanol (65%, v/v, A) and 0.1% aqueous solution of formic acid (35%, v/v, B). Analysis time was 5.0 min per run and analytes could be completely eluted within 2.8??3.8 min. The calibration concentration ranges of vandetanib, pazopanib, afatinib and dasatinib were designed as 0.50–6.10, 0.50–6.10, 0.70–7.00 and 0.70–7.00 μg·mL^?1, respectively. The intra‐ and inter‐day RSDs ranged between 0.1 and 8.9%. Quantitative information could be extracted from the unsegregated interferences of different human plasma samples with the aid of the “second‐order advantage” of three‐way (second‐order) calibration methods. All results demonstrated that the proposed method for direct quantitative analysis of four tyrosine kinase inhibitors in different complex systems possessed good characteristics of rapidity, sensitivity and efficiency, and it is expected to be an attractive choice in the fast analysis of clinical samples.     

Orthogonal array designs for the optimization of liquid-liquid-liquid microextraction of nonsteroidal anti-inflammatory drugs combined with high-performance liquid chromatography-ultraviolet detection

Orthogonal array designs (OADs) were applied for the first time to optimize liquid-liquid-liquid microextraction (LLLME) conditions for the analysis of three nonsteroidal anti-inflammatory drug residues (2-(4-chlorophenoxy)-2-methylpropionic acid, ketoprofen, and naproxen) in wastewater samples. Six relevant factors were investigated: type of organic solvent, composition of donor phase and acceptor phase, stirring speed, extraction time and salt concentration. In the first stage, mixed-level orthogonal array design, an OA16 (4(1) x 2(12)) matrix was employed to study the effect of six factors, by which the effect of each factor was estimated using individual contributions as response functions. Based on the results of the first stage, 1-octanol was chosen as organic solvent for extraction. The other five factors were selected for further optimization using an OA16 (4(5)) matrix and a 4 x 4 table to locate more exact levels for each variable. The relative standard deviations for the reproducibility of optimized LLLME varied from 6.2 to 7.1%. The coefficients of determination for calibration curves were higher than 0.9950. The method detection limits for drugs spiked in ultrapure water were in the range of 0.03-0.3 ng/mL. The final optimized conditions were applied to the analysis of drug residues in three wastewater samples in Singapore.     

Trace determination of sulfonamides residues in meat with a combination of solid-phase microextraction and liquid chromatography-mass spectrometry

An integrated method of combining solid-phase microextraction (SPME) with liquid chromatography-mass spectrometry (LC-MS) was evaluated for determination trace amount of sulfonamides in meat products. Eight commonly used sulfonamides, sulfadiazine (SDZ), sulfathiazole (STZ), sulfamerazine (SMR), sulfamethazine (SMT), sulfamonomethoxine (SMMX), sulfamethoxazole (SMXZ), sulfaquinoxaline (SQX) and sulfadimethoxine (SDMX), were investigated in this study. Chromatography was performed on a C₁₈ reversed-phase column using an isocratic acetonitrile in water as the mobile phase. Fiber coated with a 65 μm thickness of polydimethylsiloxane/divinylbenzene (PDMS/DVB) was used to extract sulfonamides at optimum conditions. Analytes were desorbed with static desorption in an SPME-HPLC desorbed chamber for 15 min and then determined by LC-MS. The detection limits of these sulfonamides in pork were from 16 μg kg⁻¹ (SMT) to 39 μg kg⁻¹ (SMMX). According to the analysis, the linear range was from 50 to 2000 μg kg⁻¹ with relative standard deviation (R.S.D.s) value below 15% (intra-day) and 19% (inter-day). The proposed method was tested by analyzing meats from a local market for sulfonamides residues. Some sulfonamides in our study were detected in the meat samples. The concentration of these residual sulfonamides ranged from 66 μg kg⁻¹ (SDZ) to 157 μg kg⁻¹ (SQX) in a chicken sample. The results demonstrate that the SPME-LC-MS system is highly effective in analyzing trace sulfonamides in meat products.     

Study of solid-phase extraction for the determination of sequestering agents in river water by high-performance liquid chromatography

Anion-exchange solid-phase extraction accompanied with high-performance liquid chromatography has been developed for the determination of six kinds of aminopolycarboxylic acids (APCAs) in river water [N-(2-hydroxyethyl)ethylenediaminetriacetate (HEDTA), ethylenediaminetetraacetate (EDTA), 1,3-propanediaminetetraacetate (PDTA), diethylenetriaminepentaacetate (DTPA), 1,2-propanediaminetetraacetate (MeEDTA), and O,O′-bis(2-aminoethyl)ethyleneglycoltetraacetate (GEDTA)]. The enrichment of APCAs using an anion-exchange cartridge was successfully done by the removal of anions, which competed with APCAs in anion-exchange processes. Barium chloride solution was added to river water and the mixture was passed through On Guard II Ag and H cartridges and then a Bond Elut Jr.SAX cartridge to enrich APCAs. After elution, APCAs were analyzed on two reversed phase C30 columns connected in series and detected with ultraviolet detection. The enrichment using solid-phase extraction permitted the determination of APCAs in river water at concentrations as low as 1 nM. Good recoveries (83–111%) were obtained for each APCA by the standard addition method on three river water samples with high accuracy (RSD 1.8–9.5%). Applying this method, two kinds of APCAs, EDTA and DTPA, were determined in samples from the Oyabe and Senbo Rivers in Japan.     

Determination of fentanyl in human breath by solid-phase microextraction and gas chromatography–mass spectrometry

Fentanyl, a kind of intravenous narcotic analgesic, is widely used in clinical anesthesia. As a potential pollution, it was detected in both the air of the cardiothoracic operating room and patients' expiratory circuit. However, whether the fentanyl in patients' expiratory circuit is exhaled by patients is unknown. In this study, breath samples were taken from the expiratory circuits of anesthetic machine linked to the patients who received intravenous fentanyl, a solid-phase microextraction (SPME) coupled with gas chromatography–mass spectrometry (GC–MS) method was developed to detect and quantify fentanyl in breath samples. The parameters influencing adsorption (extraction time, temperature,) and desorption (desorption time) of the analyte on the fiber were investigated and validated for method development. The developed method was proved to be simple, easy, and inexpensive and offer high sensitivity and reproducibility. Linear range was obtained from 0.05 ng/mL to 0.8 ng/mL. The limit of detection was 0.01 ng/mL while an interday precision of less than 12.13% (n = 5) could be achieved. Six patients were involved in this study; results showed presence of fentanyl in the breath of patients who received intravenous fentanyl, and fentanyl concentrations in breath varied from 6.00 to 20.89 pg/mL. In conclusion, fentanyl can be exhaled by patients who received intravenous fentanyl.     

Analysis of phenylurea and propanil herbicides by solid-phase microextraction and liquid chromatography combined with post-column photochemically induced fluorimetry derivatization and fluorescence detection

This study examines the application of solid-phase microextraction coupled with high performance liquid chromatography combined with post-column photochemically induced fluorimetry derivatization and fluorescence detection (SPME-HPLC-PIF-FD) for the determination of four phenylurea herbicides (monolinuron, diuron, linuron and neburon) and propanil in groundwater. Direct immersion (DI) SPME was applied using a 60 μm polydimethylsiloxane/divinylbenzene (PDMS/DVB) fiber for the extraction of the pesticides from groundwater samples. An AQUASIL C₁₈ column (150 mm × 4.6 mm i.d., 5 μm) was used for separation and determination in HPLC. The method was evaluated with respect to the limits of detection (LODs) and the limits of quantification (LOQs) according to IUPAC. The limits of detection varied between 0.019 μg L⁻¹ and 0.034 μg L⁻¹. Limits of quantification ranged between 0.051 μg L⁻¹ and 0.088 μg L⁻¹. These values meet the recommended limits for individual pesticides in groundwater (0.1 μg L⁻¹) established by the EU. Recoveries ranged between 86% and 105% and relative standard deviation values between 2% and 8%.     

Solid phase extraction and HPLC determination of veterinary pharmaceuticals in wastewater

This work focuses on the application of SPE-HPLC analysis of important veterinary pharmaceuticals from different classes in highly complex wastewater matrix. The pharmaceutical investigated included three sulfonamides (sulfamethazine, sulfadiazine and sulfaguanidine), a sulfonamide synergist (trimethoprim), a tetracycline (oxytetracycline), a fluoroquinolone (enrofloxacine) and a β-lactame (penicillin G/procaine). The method involves pre-concentration and clean-up by solid phase extraction (SPE) using Oasis HLB extraction catridges. Final analysis of the selected pharmaceutical compounds was carried out by high-performance liquid chromatography (HPLC) coupled with diode array detector (DAD). Recoveries were ranged from 68.3 to 97.9% with relative standard deviation below 8.4%. Only for sulfaguanidine low recovery was obtained. Limits of quantification were in the range 1.5-100 μg/L depending on pharmaceutical. The described method was applied to the determination of pharmaceuticals in wastewater samples from pharmaceutical industry.     

Continuous solid-phase extraction and gas chromatography–mass spectrometry determination of pharmaceuticals and hormones in water samples

A semi-automatic flow-based method for the simultaneous determination of 9 pharmaceuticals and 3 hormones in water samples in a single analytical run is proposed. The analytes were retained on a solid-phase extraction sorbent column and 1 μL of the eluate analysed by gas chromatography in combination with electron impact ionization mass spectrometry in the SIM mode. The sorbent used, Oasis-HLB, provided near-quantitative recovery of all analytes. The proposed method was validated with quite good analytical results including low limits of detection (0.01–0.06 ng L⁻¹ for 100 mL of water) and good linearity (r² > 0.993) throughout the studied concentration ranges. The method provided good accuracy (recoveries of 85–103%) and precision (between- and within-day RSD values less than 7%) in the determination of the pharmaceuticals and hormones in tap, river, pond, well, swimming pool and wastewater.     

Development and optimization of the SPE procedure for determination of pharmaceuticals in water samples by HPLC‐diode array detection

This paper focuses on the investigation of different types of SPE sorbents for the preconcentration of eight veterinary pharmaceuticals from water samples. The pharmaceuticals studied were sulfamethazine, sulfadiazine, sulfaguanidine, trimethoprim, oxytetracycline, enrofloxacin, norfloxacin and penicillin G/procaine. Five different SPE materials (Strata‐X, Strata‐X‐C, Strata SDB‐L, Strata C8 and Strata C18) from Phenomenex were compared with Oasis HLB with a view to obtaining the best cartridges for all pharmaceuticals investigated. Extraction efficiency was determined by HPLC with diode array detection (DAD). HPLC‐DAD separation and quantification of the selected pharmaceuticals were carried out under gradient elution by a binary mixture of 0.01 M oxalic acid and ACN based on cyano modified column (LiChrosphere 100 CN) from Merck. Strata‐X provided the best results in the preconcentration of 100 mL water samples, yielding average pharmaceutical recoveries of higher than 90%, except for sulfaguanidine (76.1%). The developed Strata‐X‐HLPC‐DAD method was validated and applied, for the efficient investigation of reverse osmosis/nanofiltration membranes and for the removal of these eight pharmaceuticals from the production wastewater samples. NF90 and XLE membranes were shown to be the best for the rejection of all investigated pharmaceuticals.     

Dispersive liquid–liquid microextraction combined with high performance liquid chromatography-DAD detection for the determination of sulfonylurea herbicides in water samples

A new method for the determination of four sulfonylurea herbicides (metsulfuron-methyl, chlorsulfuron, bensulfuron-methyl and chlorimuron-ethyl) in water samples was developed by dispersive liquid–liquid microextraction coupled with high performance liquid chromatography-diode array detector. Parameters that affect the extraction efficiency, such as the kind and volume of the extraction and disperser solvent, extraction time and salt addition, were investigated and optimised. Under the optimum conditions, the enrichment factors were in the range between 102 and 216. The linearity of the method was obtained in the range of 1.0–100 ng mL^?1 with the correlation coefficients (r) ranging from 0.9982 to 0.9995. The method detection limits were 0.2–0.3 ng mL^?1. The proposed method has been successfully applied to the analysis of target sulfonylurea herbicides in river, stream and well water samples with satisfactory results.     

Optimization of a sensitive method for the determination of nitro musk fragrances in waters by solid-phase microextraction and gas chromatography with micro electron capture detection using factorial experimental design

A solid-phase microextraction method (SPME) followed by gas chromatography with micro electron capture detection for determining trace levels of nitro musk fragrances in residual waters was optimized. Four nitro musks, musk xylene, musk moskene, musk tibetene and musk ketone, were selected for the optimization of the method. Factors affecting the extraction process were studied using a multivariate approach. Two extraction modes (direct SPME and headspace SPME) were tried at different extraction temperatures using two fiber coatings [Carboxen–polydimethylsiloxane (CAR/PDMS) and polydimethylsiloxane–divinylbenzene (PDMS/DVB)] selected among five commercial tested fibers. Sample agitation and the salting-out effect were also factors studied. The main effects and interactions between the factors were studied for all the target compounds. An extraction temperature of 100 °C and sampling the headspace over the sample, using either CAR/PDMS or PDMS/DVB as fiber coatings, were found to be the experimental conditions that led to a more effective extraction. High sensitivity, with detection limits in the low nanogram per liter range, and good linearity and repeatability were achieved for all nitro musks. Since the method proposed performed well for real samples, it was applied to different water samples, including wastewater and sewage, in which some of the target compounds (musk xylene and musk ketone) were detected and quantified. Figure Stardardized Pareto charts for the main effects and interactions     

A novel method for the determination of total 1,3-octanediols in apple juice via 1,3-dioxanes by solid-phase microextraction and high-speed gas chromatography

In this work, a novel, simple and fast method based on solid-phase microextraction (SPME) followed by high-speed gas chromatography (HSGC) was developed for the analysis of total 1,3-octanediols in apple juices by means of derivatization reaction to volatile 1,3-dioxanes. The derivatization reaction, SPME conditions, glycosidically bound fraction and 1,3-nonanediol as a surrogate standard were studied. The formation of 1,3-dioxanes from 1,3-diols was confirmed by GC–MS. The method was validated obtaining a regression coefficient (r²) of 0.9996, precisions between 0.3 and 9.8%, extraction recoveries in the range 94.7–112.2% and LOD of 2.9 μg l⁻¹. Experimental design has been employed in the optimization of extraction factors and robustness assessment. The method was applied to the analysis of 21 Asturian apple varieties finding a double reciprocal relationship between the concentrations of saturated and unsaturated 1,3-octanediol.     

Suitability of hollow fibre liquid-phase microextraction for the determination of acidic pharmaceuticals in wastewater by liquid chromatography-electrospray tandem mass spectrometry without matrix effects

The applicability of hollow fibre liquid-phase microextraction (LPME), as an alternative to solid-phase extraction (SPE), for the extraction/enrichment of acidic drugs (e.g. ibuprofen, clofibric acid, bezafibrate, etc.) from water samples prior to the determination by LC-ESI-MS-MS has been evaluated. After LPME method optimisation, it was found that this technique can provide very clean extracts, which do not lead to signal suppression during LC-ESI-MS-MS analysis of the analytes. The limits of quantification (0.5-42 ng/L) are suitable for the analysis of these drugs in wastewater. However repeatability needs to been improved (intra-day R.S.D. = 3.4-32%), which may be expected by automation and the development of commercially available devices and fibres specially prepared for analytical purposes. The method was finally applied to wastewater samples (treated and untreated) and results comparable to SPE were obtained.     

Simultaneous determination of ten amphetamine designer drugs in human whole blood by capillary electrophoresis with diode array detection

In recent years, a number of new designer drugs have entered the illicit drug market. The methylenedioxyderivatives of amphetamine represent the largest group of designer drugs. This paper describes a method for screening for and simultaneously quantifying 10 2,5-methylenedioxy-derivatives of amphetamine and phenethylamine in human whole blood, using capillary electrophoresis (CE) with diode array detection (DAD). Using an aqueous pH 2.5 phosphate buffer, CE analysis gave peaks with good symmetry and reproducible migration times. Under these experimental conditions, the 10 amphetamines were resolved in 15 min and without interference from biological matrices (blood). Their identification by migration time was confirmed by their UV spectra recorded with a DAD (190-350 nm). The main advantages of the present method lie in its simplicity, clean and reliable extraction from human whole blood and simultaneous detection and quantification by CE-DAD. The applicability of the method was demonstrated by analysis of in vivo rat blood samples. The method was validated according to international guidelines.     

Optimization of solid-phase microextraction procedures for the determination of tricyclic antidepressants and anticonvulsants in plasma samples by liquid chromatography

Simple, sensitive, and reproducible off-line solid-phase microextraction and liquid chromatography (SPME/LC) methods are described for the determination of seven anticonvulsants and tricyclic antidepressants in human plasma. Factorial design and simplex methodology were applied in the optimization of the SPME procedure for tricyclic antidepressants analyses. Important factors in the SPME efficiency are discussed, such as the fiber coatings (both lab-made and commercial), extraction time, pH, ionic strength, influence of plasma proteins, and desorption conditions. The development of the lab-made fiber coatings, namely, octadecylsilane, aminosilane, and polyurethane, are further described and applied to anticonvulsants analyses. The investigated plasmatic range for the evaluated anticonvulsants, using CW-TPR fiber, were the following: phenylethylmalonamide (3.00–40.0 μg mL⁻¹), phenobarbital (5.00–40.0 μg mL⁻¹), primidone (3.00–40.0 μg mL⁻¹), carbamazepine and carbamazepine-epoxide (2.00–24.0 μg mL⁻¹), phenytoin (2.00–40.0 μg mL⁻¹), and lamotrigine (0.50–12.0 μg mL⁻¹). The antidepressants’ linear plasmatic concentration ranged from 75.0 to 500 ng mL⁻¹ for imipramine, amitriptyline, and desipramine, and from 50.0 to 500 ng mL⁻¹ for nortriptyline, being in all cases, the limit of quantification represented by the lowest value. The precision (interassays) for all investigated drugs in plasma sample spiked with different concentrations of each analyte and submitted to the described procedures were lower than 15%. The off-line SPME/LC methodologies developed allow anticonvulsants and antidepressants analyses from therapeutic to toxic levels for therapeutic drug monitoring.